LM613IWM [NSC]
Dual Operational Amplifiers, Dual Comparators, and Adjustable Reference; 双路运算放大器,双路比较器和可调参考型号: | LM613IWM |
厂家: | National Semiconductor |
描述: | Dual Operational Amplifiers, Dual Comparators, and Adjustable Reference |
文件: | 总22页 (文件大小:1040K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
June 1998
LM613
Dual Operational Amplifiers, Dual Comparators, and
Adjustable Reference
General Description
Features
The LM613 consists of dual op-amps, dual comparators, and
a programmable voltage reference in a 16-pin package. The
op-amps out-performs most single-supply op-amps by pro-
viding higher speed and bandwidth along with low supply
current. This device was specifically designed to lower cost
and board space requirements in transducer, test, measure-
ment, and data acquisition systems.
OP AMP
n Low operating current (Op Amp): 300 µA
n Wide supply voltage range: 4V to 36V
n Wide common-mode range: V− to (V+ − 1.8V)
n Wide differential input voltage: 36V
n Available in plastic package rated for Military Temp.
±
Range Operation
Combining a stable voltage reference with wide output swing
op-amps makes the LM613 ideal for single supply transduc-
ers, signal conditioning and bridge driving where large
common-mode-signals are common. The voltage reference
consists of a reliable band-gap design that maintains low dy-
namic output impedance (1Ω typical), excellent initial toler-
ance (0.6%), and the ability to be programmed from 1.2V to
6.3V via two external resistors. The voltage reference is very
stable even when driving large capacitive loads, as are com-
monly encountered in CMOS data acquisition systems.
REFERENCE
n Adjustable output voltage: 1.2V to 6.3V
n Tight initial tolerance available: 0.6%
n Wide operating current range: 17 µA to 20 mA
n Tolerant of load capacitance
±
Applications
n Transducer bridge driver
n Process and mass flow control systems
n Power supply voltage monitor
n Buffered voltage references for A/D’s
™
As a member of National’s Super-Block family, the LM613
is a space-saving monolithic alternative to a multi-chip solu-
tion, offering a high level of integration without sacrificing
performance.
Connection Diagrams
E Package Pinout
DS009226-1
Top View
DS009226-48
™
Super-Block is a trademark of National Semiconductor Corporation.
© 1999 National Semiconductor Corporation
DS009226
www.national.com
Ordering Information
Reference
Temperature Range
Industrial
Package
NSC
Tolerance & VOS
Drawing
Military
−55˚C ≤ TA ≤ +125˚C
LM613AMN
Commercial
0˚C ≤ TA ≤ +70˚C
—
−40˚C ≤ TA ≤ +85˚C
LM613AIN
±
0.6%
16-Pin
Molded DIP
16-Pin
N16E
J16A
E20A
N16E
M16B
80 ppm/˚C Max.
VOS ≤ 3.5 mV
LM613AMJ/883
(Note 14)
—
—
—
—
Ceramic DIP
20-Pin
LM613AME/883
(Note 14)
LCC
±
2.0%
LM613MN
LM613IN
LM613IWM
LM613CN
16-Pin
150 ppm/˚C Max.
Molded DIP
16-Pin Wide
Surface Mount
VOS ≤ 5.0 mV Max.
—
www.national.com
2
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Thermal Resistance,
Junction-to-Ambient (Note 5)
N Package
100˚C/W
150˚C/W
WM Package
Soldering Information (10 Sec.)
N Package
WM Package
260˚C
220˚C
Voltage on Any Pin Except VR
(referred to V−pin)
(Note 2)
(Note 3)
±
ESD Tolerance (Note 6)
1 kV
36V (Max)
−0.3V (Min)
Current through Any Input Pin
& VR Pin
Operating Temperature Range
±
20 mA
LM613AI, LM613BI:
LM613AM, LM613M:
LM613C:
−40˚C to +85˚C
−55˚C to +125˚C
0˚C ≤ TJ ≤ +70˚C
Differential Input Voltage
Military and Industrial
Commercial
±
±
36V
32V
Storage Temperature Range
−65˚C ≤ TJ ≤ +150˚C
Maximum Junction Temp.(Note 4)
150˚C
Electrical Characteristics
+
These specifications apply for V− GND 0V, V
=
=
=
= = =
5V, VCM VOUT 2.5V, IR 100 µA, FEEDBACK pin shorted to GND,
=
unless otherwise specified. Limits in standard typeface are for TJ 25˚C; limits in boldface type apply over the Operating
Temperature Range.
LM613AM
LM613AI
Limits
LM613M
LM613I
LM613C
Limits
(Note 8)
1000
1070
2.8
Typical
Symbol
Parameter
Conditions
(Note 7)
Units
(Note 8)
= ∞
IS
Total Supply Current
Supply Voltage Range
RLOAD
,
450
550
2.2
2.9
46
940
1000
2.8
3
µA (Max)
µA (Max)
V (Min)
4V ≤ V+ ≤ 36V (32V for LM613C)
VS
3
V (Min)
36
32
V (Max)
V (Max)
43
36
32
OPERATIONAL AMPLIFIERS
VOS1
VOS Over Supply
4V ≤ V+ ≤ 36V
(4V ≤ V+ ≤ 32V for LM613C)
1.5
2.0
1.0
1.5
15
3.5
6.0
3.5
6.0
5.0
7.0
5.0
7.0
mV (Max)
mV (Max)
mV (Max)
mV (Max)
=
=
−
VOS2
VOS Over VCM
VCM 0V through VCM
(V+ − 1.8V), V+ 30V, V
=
=
0V
Average VOS Drift
(Note 8)
µV/˚C
(Max)
IB
Input Bias Current
10
11
25
30
4
35
40
4
nA (Max)
nA (Max)
nA (Max)
nA (Max)
IOS
Input Offset Current
Average Offset Current
0.2
0.3
5
5
4
pA/˚C
RIN
CIN
en
Input Resistance
Input Capacitance
Voltage Noise
Differential
1000
6
MΩ
Common-Mode
pF
=
f
100 Hz, Input Referred
100 Hz, Input Referred
=
74
=
In
Current Noise
f
58
CMRR
Common-Mode
Rejection Ratio
Power Supply
Rejection Ratio
V+ 30V, 0V ≤ VCM ≤ (V+ − 1.8V)
95
90
80
75
80
75
75
70
75
70
dB (Min)
dB (Min)
dB (Min)
dB (Min)
=
CMRR 20 log (∆VCM/∆VOS
)
+
4V ≤ V+ ≤ 30V, VCM V /2,
110
100
=
PSRR
+
=
PSRR 20 log (∆V /VOS
)
3
www.national.com
Electrical Characteristics (Continued)
+
These specifications apply for V− GND 0V, V
=
=
=
= = =
5V, VCM VOUT 2.5V, IR 100 µA, FEEDBACK pin shorted to GND,
=
unless otherwise specified. Limits in standard typeface are for TJ 25˚C; limits in boldface type apply over the Operating
Temperature Range.
LM613AM
LM613AI
Limits
LM613M
LM613I
LM613C
Limits
Typical
Symbol
Parameter
Conditions
(Note 7)
Units
(Note 8)
(Note 8)
OPERATIONAL AMPLIFIERS
+
=
=
30V,
AV
Open Loop
Voltage Gain
Slew Rate
RL 10 kΩ to GND, V
500
50
100
40
94
40
V/mV
(Min)
V/µs
5V ≤ VOUT ≤ 25V
V+ 30V (Note 9)
=
SR
0.70
0.65
0.8
0.55
0.45
0.50
0.45
=
GBW
VO1
Gain Bandwidth
CL 50 pF
MHz
0.5
MHz
Output Voltage
Swing High
RL 10 kΩ to GND,
V+ − 1.4
V+ − 1.6
V− + 0.8
V− + 0.9
25
V+ − 1.7
V+ − 1.9
V− + 0.9
V− + 1.0
V+ − 1.8
V+ − 1.9
V− + 0.95
V− + 1.0
V (Min)
=
V+ 36V (32V for LM613C)
+
V (Min)
=
=
VO2
Output Voltage
Swing Low
RL 10 kΩ to V ,
V (Max)
V (Max)
mA (Min)
mA (Min)
mA (Min)
mA (Min)
mA (Max)
mA (Max)
mA (Max)
mA (Max)
V+ 36V (32V for LM613C)
=
+
=
=
=
IOUT
ISINK
ISHORT
Output Source Current
VOUT 2.5V, V
0V,
0V,
20
16
IN
V−
−0.3V
15
13
13
=
IN
+
=
Output Sink Current
Short Circuit Current
VOUT 1.6V, V
17
14
13
IN
=
V−
0.3V
9
8
8
=
IN
+
=
VOUT 0V,V
3V,
2V,
30
50
50
IN
V−
2V
40
60
60
=
IN
+
=
=
VOUT 5V, V
30
60
70
IN
V−
3V
32
80
90
=
IN
COMPARATORS
VOS
Offset Voltage
4V ≤ V+ ≤ 36V (32V for LM613C),
1.0
2.0
1.0
3.0
6.0
3.0
5.0
7.0
5.0
mV (Max)
mV (Max)
mV (Max)
=
RL 15 kΩ
Offset Voltage
over VCM
0V ≤ VCM ≤ 36V
V+ 36V, (32V for LM613C)
=
1.5
15
6.0
7.0
mV (Max)
µV/˚C
Average Offset
Voltage Drift
(Max)
IB
Input Bias Current
5
25
30
4
35
40
4
nA (Max)
nA (Max)
nA (Max)
nA (Max)
V/mV
8
IOS
Input Offset Current
Voltage Gain
0.2
0.3
500
5
5
=
AV
RL 10 kΩ to 36V (32V for
LM613C)
2V ≤ VOUT ≤ 27V
100
1.5
2.0
20
V/mV
µs
−
=
=
TTL Swing,
tr
Large Signal
V+
1.4V, V
IN
IN
=
Response Time
Output Sink Current
RL 5.1 kΩ
µs
−
=
=
ISINK
V+
0V, V
1V,
10
8
10
8
mA (Min)
mA (Min)
mA (Min)
mA (Min)
µA (Max)
µA (Max)
IN
IN
=
VOUT 1.5V
13
=
VOUT 0.4V
2.8
2.4
0.1
0.2
1.0
0.5
10
0.8
0.5
10
−
ILEAK
Output Leakage
Current
V+
1V, V
0V,
=
=
IN
IN
=
VOUT 36V (32V for LM613C)
VOLTAGE REFERENCE
VR
Voltage Reference
(Note 10)
1.244
1.2365
1.2191
V (Min)
www.national.com
4
Electrical Characteristics (Continued)
+
These specifications apply for V− GND 0V, V
=
=
=
= = =
5V, VCM VOUT 2.5V, IR 100 µA, FEEDBACK pin shorted to GND,
=
unless otherwise specified. Limits in standard typeface are for TJ 25˚C; limits in boldface type apply over the Operating
Temperature Range.
LM613AM
LM613AI
Limits
LM613M
LM613I
LM613C
Limits
Typical
Symbol
Parameter
Conditions
(Note 7)
Units
(Note 8)
(Note 8)
VOLTAGE REFERENCE
1.2515
1.2689
V (Max)
±
±
2%)
150
(
0.6%)
(
Average Temp. Drift
(Note 11)
(Note 12)
10
80
ppm/˚C
(Max)
Hysteresis
3.2
µV/˚C
VR Change
with Current
VR(100 µA) − VR(17 µA)
0.05
1
1
mV (Max)
mV (Max)
0.1
1.1
1.1
V
R(10 mA) − VR(100 µA)
1.5
2.0
0.2
0.6
2.5
2.8
5
5
5.5
0.56
13
mV (Max)
mV (Max)
Ω (Max)
(Note 13)
5.5
R
Resistance
∆VR(10 0.1 mA)/9.9 mA
→
0.56
13
7
∆VR(100 17 µA)/83 µA
→
Ω (Max)
VR Change
VR(Vro Vr) − VR(Vro
7
mV (Max)
mV (Max)
=
=
6.3V)
with High VRO
(5.06V between Anode and
FEEDBACK)
10
10
VR Change with
VANODE Change
VR(V+ 5V) − VR(V+
0.1
0.1
0.01
0.01
22
1.2
1.3
1
1.2
1.3
1
mV (Max)
mV (Max)
mV (Max)
mV (Max)
nA (Max)
nA (Max)
µVRMS
=
=
36V)
(V+ 32V for LM613C)
VR(V+ 5V) − VR(V+
=
=
=
3V)
1.5
35
40
1.5
50
55
IFB
FEEDBACK Bias
Current
VANODE ≤ VFB ≤ 5.06V
29
en
VR Noise
10 Hz to 10 kHz,
30
=
VRO VR
Note 1: Absolute maximum ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the de-
vice beyond its rated operating conditions.
+
Note 2: Input voltage above V is allowed. As long as one input pin voltage remains inside the common-mode range, the comparator will deliver the correct output.
Note 3: More accurately, it is excessive current flow, with resulting excess heating, that limits the voltages on all pins. When any pin is pulled a diode drop below
−
V , a parasitic NPN transistor turns ON. No latch-up will occur as long as the current through that pin remains below the Maximum Rating. Operation is undefined
and unpredictable when any parasitic diode or transistor is conducting.
Note 4: Simultaneous short-circuit of multiple comparators while using high supply voltages may force junction temperature above maximum, and thus should not
be continuous.
=
Note 5: Junction temperature may be calculated using T
T + P θ . The given thermal resistance is worst-case for packages in sockets in still air. For packages
A D JA
J
soldered to copper-clad board with dissipation from one comparator or reference output transistor, nominal θ is 90˚C/W for the N package, and 135˚C/W for the
JA
WM package.
Note 6: Human body model, 100 pF discharged through a 1.5 kΩ resistor.
=
Note 7: Typical values in standard typeface are for T
25˚C; values in bold face type apply for the full operating temperature range. These values represent the
J
most likely parametric norm.
Note 8: All limits are guaranteed at room temperature (standard type face) or at operating temperature extremes (bold type face).
Note 9: Slew rate is measured with the op amp in a voltage follower configuration. For rising slew rate, the input voltage is driven from 5V to 25V, and the output
@
voltage transition is sampled at 10V and 20V. For falling slew rate, the input voltage is driven from 25V to 5V, and the output voltage transition is sampled at 20V
and 10V.
Note 10:
V is the Cathode-to-feedback voltage, nominally 1.244V.
R
Note 11: Average reference drift is calculated from the measurement of the reference voltage at 25˚C and at the temperature extremes. The drift, in ppm/˚C, is
6
10 •∆V /(VR[25˚C]•∆T ), where ∆V is the lowest value subtracted from the highest, V
is the value at 25˚C, and ∆T is the temperature range. This parameter
J
R
J
R
R[25˚C]
is guaranteed by design and sample testing.
Note 12: Hysteresis is the change in V caused by a change in T , after the reference has been “dehysterized”. To dehysterize the reference; that is minimize the
R
J
hysteresis to the typical value, its junction temperature should be cycled in the following pattern, spiraling in toward 25˚C: 25˚C, 85˚C, −40˚C, 70˚C, 0˚C, 25˚C.
Note 13: Low contact resistance is required for accurate measurement.
5
www.national.com
Electrical Characteristics (Continued)
Note 14: A military RETS 613AMX electrical test specification is available on request. The Military screened parts can also be procured as a Standard Military Draw-
ing.
Simplified Schematic Diagrams
Op Amp
DS009226-2
Comparator
DS009226-3
www.national.com
6
Simplified Schematic Diagrams (Continued)
Reference/Bias
DS009226-4
Typical Performance Characteristics (Reference) TJ 25˚C, FEEDBACK pin shorted to V−
=
=
0V, unless otherwise noted
Reference Voltage vs Temp.
Reference Voltage Drift
Accelerated Reference
Voltage Drift vs Time
DS009226-50
DS009226-49
DS009226-51
Reference Voltage vs
Current and Temperature
Reference Voltage vs
Current and Temperature
Reference Voltage vs
Reference Current
DS009226-52
DS009226-53
DS009226-54
7
www.national.com
Typical Performance Characteristics (Reference) TJ 25˚C, FEEDBACK pin shorted to V−
=
=
0V, unless otherwise noted (Continued)
Reference Voltage vs
Reference Current
Reference AC
Stability Range
FEEDBACK Current vs
FEEDBACK-to-Anode Voltage
DS009226-55
DS009226-56
DS009226-57
FEEDBACK Current vs
FEEDBACK-to-Anode Voltage
Reference Noise Voltage
vs Frequency
Reference Small-Signal
Resistance vs Frequency
DS009226-58
DS009226-59
DS009226-60
Reference Power-Up Time
Reference Voltage with
FEEDBACK Voltage Step
Reference Voltage with
z
100
12 µA Current Step
DS009226-61
DS009226-62
DS009226-63
www.national.com
8
Typical Performance Characteristics (Reference) TJ 25˚C, FEEDBACK pin shorted to V−
=
=
0V, unless otherwise noted (Continued)
Reference Step Response
Reference Voltage Change
with Supply Voltage Step
Reference Change vs
Common-Mode Voltage
z
for 100 µA
Current Step
10 mA
DS009226-65
DS009226-64
DS009226-66
Typical Performance Characteristics (Op Amps) V+ 5V, V− GND 0V, VCM V+/2, VOUT
=
=
=
=
+
=
=
V /2, TJ 25˚C, unless otherwise noted
Input Common-Mode
Voltage Range vs
Temperature
VOS vs Junction
Temperature
Input Bias Current vs
Common-Mode Voltage
DS009226-68
DS009226-69
DS009226-67
Large-Signal
Step Response
Output Voltage Swing
vs Temp. and Current
DS009226-70
DS009226-71
9
www.national.com
Typical Performance Characteristics (Op Amps) V+ 5V, V− GND 0V, VCM V+/2,
=
=
=
=
+
=
=
VOUT V /2, TJ 25˚C, unless otherwise noted (Continued)
Output Source Current vs
Output Voltage and Temp.
Output Sink Current vs
Output Voltage
Output Swing,
Large Signal
DS009226-72
DS009226-73
DS009226-74
Output Impedance vs
Frequency and Gain
Small Signal Pulse
Response vs Temp.
Small-Signal Pulse
Response vs Load
DS009226-76
DS009226-77
DS009226-75
Op Amp Voltage Noise
vs Frequency
Op Amp Current Noise
vs Frequency
Small-Signal Voltage Gain vs
Frequency and Temperature
DS009226-78
DS009226-79
DS009226-80
www.national.com
10
Typical Performance Characteristics (Op Amps) V+ 5V, V− GND 0V, VCM V+/2,
=
=
=
=
+
=
=
VOUT V /2, TJ 25˚C, unless otherwise noted (Continued)
Small-Signal Voltage Gain
vs Frequency and Load
Follower Small-Signal
Frequency Response
Common-Mode Input
Voltage Rejection Ratio
DS009226-81
DS009226-82
DS009226-83
Power Supply Current
vs Power Supply Voltage
Positive Power Supply
Voltage Rejection Ratio
Negative Power Supply
Voltage Rejection Ratio
DS009226-85
DS009226-84
DS009226-86
Slew Rate vs Temperature
Input Offset Current vs
Junction Temperature
Input Bias Current vs
Junction Temperature
DS009226-87
DS009226-88
DS009226-89
11
www.national.com
Typical Performance Characteristics (Comparators)
Output Sink Current
Input Bias Current vs
Common-Mode Voltage
DS009226-10
DS009226-11
DS009226-13
DS009226-15
Comparator
Response Times — Inverting
Input, Positive Transition
Comparator
Response Times — Inverting
Input, Negative Transition
DS009226-12
Comparator
Response Times — Non-Inverting
Input, Positive Transition
Comparator
Response Times — Non-Inverting
Input, Negative Transition
DS009226-14
www.national.com
12
Typical Performance Characteristics (Comparators) (Continued)
Comparator
Response Times — Inverting
Input, Positive Transition
Comparator
Response Times — Inverting
Input, Negative Transition
DS009226-16
DS009226-17
Comparator
Response Times — Non-Inverting
Input, Positive Transition
Comparator
Response Times — Non-Inverting
Input, Negative Transition
DS009226-18
DS009226-19
Typical Performance Distributions
Average VOS Drift
Average VOS Drift
Military Temperature Range
Industrial Temperature Range
DS009226-20
DS009226-21
13
www.national.com
Typical Performance Distributions (Continued)
Average VOS Drift
Average IOS Drift
Commercial Temperature Range
Military Temperature Range
DS009226-22
DS009226-23
Average IOS Drift
Op Amp Voltage
Industrial Temperature Range
Noise Distribution
DS009226-24
DS009226-27
Average IOS Drift
Op Amp Current
Commercial Temperature Range
Noise Distribution
DS009226-25
DS009226-28
www.national.com
14
Typical Performance Distributions
(Continued)
Voltage Reference Broad-Band
Noise Distribution
DS009226-30
FIGURE 2. Reference Equivalent Circuit
DS009226-26
Application Information
VOLTAGE REFERENCE
DS009226-31
FIGURE 3. 1.2V Reference
Capacitors in parallel with the reference are allowed. See the
Reference AC Stability Range typical curve for capacitance
values — from 20 µA to 3 mA any capacitor value is stable.
With the reference’s wide stability range with resistive and
capacitive loads, a wide range of RC filter values will perform
noise filtering.
Reference Biasing
The voltage reference is of a shunt regulator topology that
models as a simple zener diode. With current Ir flowing in the
“forward” direction there is the familiar diode transfer func-
tion. Ir flowing in the reverse direction forces the reference
voltage to be developed from cathode to anode. The cath-
ode may swing from a diode drop below V− to the reference
voltage or to the avalanche voltage of the parallel protection
=
Adjustable Reference
The FEEDBACK pin allows the reference output voltage,
ro, to vary from 1.24V to 6.3V. The reference attempts to
hold Vr at 1.24V. If Vr is above 1.24V, the reference will con-
duct current from Cathode to Anode; FEEDBACK current al-
ways remains low. If FEEDBACK is connected to Anode,
V
diode, nominally 7V. A 6.3V reference with V+
allowed.
3V is
=
=
then Vro Vr 1.24V. For higher voltages FEEDBACK is
held at a constant voltage above Anode — say 3.76V for Vro
=
5V. Connecting a resistor across the constant Vr generates
=
a current I R1/Vr flowing from Cathode into FEEDBACK
node. A Thevenin equivalent 3.76V is generated from FEED-
=
BACK to Anode with R2 3.76/I. Keep I greater than one
thousand times larger than FEEDBACK bias current for
<
0.1% error — I≥32 µA for the military grade over the military
temperature range (I≥5.5 µA for a 1% untrimmed error for a
DS009226-29
commercial part).
FIGURE 1. Voltage Associated with Reference
(current source Ir is external)
The reference equivalent circuit reveals how Vr is held at the
constant 1.2V by feedback, and how the FEEDBACK pin
passes little current.
To generate the required reverse current, typically a resistor
is connected from a supply voltage higher than the reference
voltage. Varying that voltage, and so varying Ir, has small ef-
fect with the equivalent series resistance of less than an ohm
at the higher currents. Alternatively, an active current source,
such as the LM134 series, may generate Ir.
DS009226-32
FIGURE 4. Thevenin Equivalent of Reference
with 5V Output
15
www.national.com
Application Information (Continued)
DS009226-36
DS009226-33
=
=
=
=
FIGURE 8. Diode in Series with R1 Causes Voltage
Across R1 and R2 to be Proportional to Absolute
Temperature (PTAT)
R1 Vr/I 1.24/32µ 39k
=
=
R2 R1 {(Vro/Vr) − 1} 39k {(5/1.24) − 1)} 118k
FIGURE 5. Resistors R1 and R2 Program Reference
Output Voltage to be 5V
Connecting a resistor across Cathode-to-FEEDBACK cre-
ates a 0 TC current source, but a range of TCs may be
synthesized.
Understanding that Vr is fixed and that voltage sources, re-
sistors, and capacitors may be tied to the FEEDBACK pin, a
range of Vr temperature coefficients may be synthesized.
DS009226-37
DS009226-34
=
=
I
Vr/R1 1.24/R1
FIGURE 6. Output Voltage has Negative Temperature
Coefficient (TC) if R2 has Negative TC
FIGURE 9. Current Source is Programmed by R1
DS009226-35
DS009226-38
FIGURE 7. Output Voltage has Positive TC
if R1 has Negative TC
FIGURE 10. Proportional-to-Absolute-Temperature
Current Source
DS009226-39
FIGURE 11. Negative-TC Current Source
www.national.com
16
LM124), and increased slew rate as shown in the char-
acteristic curves. A resistor pull-up or pull-down will force
class-A operation with only the PNP or NPN output tran-
sistor conducting, eliminating cross-over distortion.
Application Information (Continued)
Reference Hysteresis
The reference voltage depends, slightly, on the thermal his-
tory of the die. Competitive micro-power products vary — al-
ways check the data sheet for any given device. Do not as-
sume that no specification means no hysteresis.
3. Capacitive Drive: Limited by the output pole caused by
the output resistance driving capacitive loads,
a
pull-down resistor conducting 1 mA or more reduces the
output stage NPN re until the output resistance is that of
the current limit 25Ω. 200 pF may then be driven without
oscillation.
OPERATIONAL AMPLIFIERS AND COMPARATORS
Any amp, comparator, or the reference may be biased in any
way with no effect on the other sections of the LM613, ex-
cept when a substrate diode conducts, see Electrical Char-
acteristics (Note 1). For example, one amp input may be out-
side the common-mode range, another amp may be
operating as a comparator, and all other sections may have
all terminals floating with no effect on the others. Tying in-
verting input to output and non-inverting input to V− on un-
used amps is preferred. Unused comparators should have
non-inverting input and output tied to V+, and inverting input
tied to V−. Choosing operating points that cause oscillation,
such as driving too large a capacitive load, is best avoided.
Comparator Output Stage
The comparators, like the LM139 series, have open-collector
output stages. A pull-up resistor must be added from each
output pin to a positive voltage for the output transistor to
switch properly. When the output transistor is OFF, the out-
put voltage will be this external positive voltage.
For the output voltage to be under the TTL-low voltage
threshold when the output transistor is ON, the output cur-
rent must be less than 8 mA (over temperature). This im-
pacts the minimum value of pull-up resistor.
The offset voltage may increase when the output voltage is
low and the output current is less than 30 µA. Thus, for best
accuracy, the pull-up resistor value should be low enough to
allow the output transistor to sink more than 30 µA.
Op Amp Output Stage
These op amps, like the LM124 series, have flexible and
relatively wide-swing output stages. There are simple rules
to optimize output swing, reduce cross-over distortion, and
optimize capacitive drive capability:
Op Amp and Comparator Input Stage
The lateral PNP input transistors, unlike those of most op
amps, have BVEBO equal to the absolute maximum supply
voltage. Also, they have no diode clamps to the positive sup-
ply nor across the inputs. These features make the inputs
look like high impedances to input sources producing large
differential and common-mode voltages.
1. Output Swing: Unloaded, the 42 µA pull-down will bring
the output within 300 mV of V− over the military tempera-
ture range. If more than 42 µA is required, a resistor from
output to V− will help. Swing across any load may be im-
proved slightly if the load can be tied to V+, at the cost of
poorer sinking open-loop voltage gain.
2. Cross-Over Distortion: The LM613 has lower cross-over
distortion (a 1 VBE deadband versus 3 VBE for the
Typical Applications
DS009226-40
FIGURE 12. High Current, High Voltage Switch
17
www.national.com
Typical Applications (Continued)
DS009226-41
FIGURE 13. High Speed Level Shifter. Response time is approximately
1.5 µs, where output is either approximately +V or −V.
DS009226-42
FIGURE 14. Low Voltage Regulator. Dropout voltage is approximately 0.2V.
DS009226-43
*10k must be low
t.c. trimpot
FIGURE 15. Ultra Low Noise, 10.00V Reference. Total output noise is typically 14 µVRMS
.
www.national.com
18
Typical Applications (Continued)
DS009226-44
FIGURE 16. Basic Comparator
DS009226-46
FIGURE 18. Wide-Input Range
Comparator with TTL Output
DS009226-45
FIGURE 17. Basic Comparator with External Strobe
DS009226-47
FIGURE 19. Comparator with
Hysteresis (∆VH +V(1k/1M))
=
19
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted
20-Lead Small Outline Package (E)
Order Number LM613AME/883
NS Package Number E20A
16-Lead Ceramic Dual-In-Line Package (J)
Order Number LM613AMJ/883
NS Package Number J16A
www.national.com
20
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
16-Lead Small Outline Package (WM)
Order Number LM613IWM
NS Package Number M16B
16-Lead Molded Dual-In-Line Package (N)
Order Number LM613CN, LM613AIN, LM613IN, LM613AMN or LM613MN
NS Package Number N16A
21
www.national.com
Notes
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
Fax: +49 (0) 1 80-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
Email: sea.support@nsc.com
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
相关型号:
LM613IWM/NOPB
Dual Operational Amplifier, Dual Comparator and Adjustable Reference 16-SOIC -40 to 85
TI
LM613IWMX
IC DUAL OP-AMP, 7000 uV OFFSET-MAX, 0.5 MHz BAND WIDTH, PDSO16, SOP-16, Operational Amplifier
NSC
LM613IWMX/NOPB
IC DUAL OP-AMP, 7000 uV OFFSET-MAX, 0.5 MHz BAND WIDTH, PDSO16, SOP-16, Operational Amplifier
NSC
LM613IWMX/NOPB
Dual Operational Amplifier, Dual Comparator and Adjustable Reference 16-SOIC -40 to 85
TI
©2020 ICPDF网 联系我们和版权申明