TDA8025HN/C1,551 [NXP]
TDA8025 - Low voltage supply smart card interface QFN 32-Pin;型号: | TDA8025HN/C1,551 |
厂家: | NXP |
描述: | TDA8025 - Low voltage supply smart card interface QFN 32-Pin |
文件: | 总38页 (文件大小:180K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TDA8025
IC card interface
Rev. 01 — 6 April 2009
Product data sheet
1. General description
The TDA8025 is a cost-effective analog interface for asynchronous smart cards operating
at 3 V, 1.8 V or optionally, 1.2 V. Using few external components, the TDA8025 provides
integrated supply, protection and control functions for a range of applications.
2. Features
I Integrated circuit smart card interface
I 3 V, 1.8 V or 1.2 V smart card supply
I Low power consumption in inactive mode
I Three protected, half duplex, bidirectional buffered input/output lines (C4, C7 and C8)
I VCC regulation:
N 3 V, 1.8 V or optionally 1.2 V at ± 5 % using one 220 nF and one 470 nF low ESR
multilayer ceramic capacitor.
N Current pulse handling for pulses of 40 nAs at VCC = 3 V, 15 nAs at VCC = 1.8 V or
VCC = 1.2 V up to 20 MHz
I Thermal and short-circuit protection for all card contacts
I Automatic activation and deactivation sequences triggered by short-circuit, card
take-off, overheating, falling VDD(INTF) and VDD(INTREGD)
I Enhanced card-side ElectroStatic Discharge (ESD) protection of > 6 kV
I Clock signal using the internal oscillator or an external crystal (≤ 26 MHz) connected to
pin XTAL1
I Card clock generation up to 20 MHz with synchronous frequency changes of fxtal
,
1⁄2 fxtal, 1⁄4 fxtal or 1⁄8 fxtal using pins CLKDIV1 and CLKDIV2
I Non-inverted control of pin RST using pin RSTIN
I NDS certified
I Supply supervisors during power on and off:
N VDD(INTREGD) using a fixed threshold
N VDD(INTF) using resistor bridge threshold adjustment
I Built-in debouncing on card presence contacts (typically 4.5 ms)
I Multiplexed status signal using pin OFFN
3. Applications
I Pay TV
I Electronic payment
I Identification
I Bank card readers
TDA8025
NXP Semiconductors
IC card interface
4. Quick reference data
Table 1.
Symbol
Supplies
VDDI(REG)
Quick reference data
Parameter
Conditions
Min
Typ
Max
Unit
regulator input
supply voltage
pin CONFIG = ground
3.6
3
5
5.5
3.6
V
V
pin CONFIG = VDDI(REG); regulator is
bypassed
3.3
[1]
VDD(INTF)
interface supply
voltage
pin CONFIG = ground
1.6
1.6
3.0
3.0
3.3
V
V
pin CONFIG = VDDI(REG) and VDD(INTF) not
connected to VDDI(REG) and VDD(INTREGD)
VDDI(REG)
+ 0.3
pin CONFIG = VDDI(REG) with VDD(INTF)
connected to VDDI(REG) and VDD(INTREGD)
3
3.3
3.6
V
IDDI(REG)
regulator input
supply current
inactive mode
VDDI(REG) = 5 V; fxtal = stopped
VDDI(REG) = 5 V; fxtal = 10 MHz;
-
-
-
-
300
2.5
µA
mA
f
CLK = 1⁄8 fXTAL
active mode
VCC = 3 V; ICC = 65 mA
VCC = 1.8 V; ICC = 65 mA
VCC = 1.2 V; ICC = 30 mA
-
-
-
-
-
-
85
85
50
mA
mA
mA
Card supply voltage
VCC
supply voltage
including ripple
inactive mode
no load
−0.1
−0.1
-
-
+0.1
+0.3
V
V
ICC = 1 mA
active mode
3 V card:
ICC < 65 mA DC
single current pulse −100 mA; 2 µs
2.85
2.76
2.76
3.05
3.05
3.05
3.15
3.20
3.20
V
V
V
current pulses of 40 nAs at
ICC < 200 mA; t < 400 ns
1.8 V card:
ICC < 65 mA DC
1.71
1.66
1.66
1.83
1.83
1.83
1.89
1.94
1.94
V
V
V
single current pulse −100 mA; 2 µs
current pulses of 15 nAs with
ICC < 200 mA; t < 400 ns
1.2 V card:
ICC < 30 mA DC
1.1
1.2
1.2
1.2
1.3
1.3
1.3
V
V
V
single current pulse −100 mA; 2 µs
1.1
current pulses of 15 nAs with ICC
< 200 mA; t < 400 ns
1.10
Vripple(p-p)
peak-to-peak ripple pin VCC; 20 kHz to 200 MHz
voltage
-
-
350
mV
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
2 of 38
TDA8025
NXP Semiconductors
IC card interface
Table 1.
Symbol
ICC
Quick reference data …continued
Parameter
Conditions
0 V to 3 V
Min
Typ
Max
65
Unit
mA
supply current
-
-
0 V to 1.8 V
0 V to 1.2 V
up or down
-
-
65
mA
-
-
30
mA
SR
slew rate
0.02
0.14
0.26
V/µs
General
tdeact
Ptot
[2]
deactivation time
total sequence
35
-
80
-
100
µs
total power
dissipation
Tamb = −25 °C to +85 °C
0.56
W
Tamb
ambient temperature
−25
-
+85
°C
[1] To enable the microcontroller to provide the required maximum voltage input level on XTAL1, VDD(INTF) must not exceed
VDD(INTREGD) + 0.3 V. See Section 8.1 on page 7 for specific limitations on the maximum VDD(INTF) voltage and Table 8 on page 23 for
the limits of XTAL1.
[2] See Figure 12 on page 18.
5. Ordering information
Table 2.
Ordering information
Type number
Package
Name
Description
Version
TDA8025HN
HVQFN32 plastic thermal enhanced very thin quad flat package; no leads;
SOT617-1
32 terminals; body 5 × 5 × 0.85 mm
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
3 of 38
TDA8025
NXP Semiconductors
IC card interface
6. Block diagram
V
DDI(REG)
TEST2
TEST1 TEST4
10 µF
GND
20
CONFIG
16
21
2
3
32
24
19
REGULATOR
TEST
TEST3
100 nF
V
DD(INTREGD)
V
DD(INTF)
R1
10 µF
SUPPLY
INTERNAL
REFERENCE
INTERNAL
OSCILLATOR
TDA8025
PORADJ 25
(1)
R2
VOLTAGE
SENSE
CLKUP
18
14
V
ALARMN
EN1
CC
V
CC
10
9
470 nF
PVCC
CGND
PRES
LOOP
PRESN
220 nF
17
15
22
1
EN4
EN3
RST
SEQUENCER
RESET
GENERATOR
RSTIN
CMDVCCN
OFFN
23
6
CLK
CLOCK
CIRCUIT
CLOCK
GENERATOR
EN2
CLK
CLKDIV1
CLKDIV2
ENCLKIN
VCC_SEL1
VCC_SEL2
V
DD(INTREGD)
INTERFACE
C5
C6
C7
C8
C1
5
MULTIPLEXER
THERMAL
PROTECTION
C2
C3
C4
26
7
11
13
12
I/O
I/O
TRANSCEIVER
Level shifter
(V
)
XTAL
DD(INTF)
8
AUX1
AUX2
I/O
TRANSCEIVER
OSCILLATOR
(V
)
DD(INTREGD)
I/O
220 nF
TRANSCEIVER
4
27
28
29
30
31
100 nF
XTAL1
AUX1UC
AUX2UC
V
XTAL2
I/OUC
001aai957
DD(INTF)
(1) Optional external resistor bridge. If this bridge is not needed, connect pin PORADJ to VDD(INTF)
.
Fig 1. Block diagram
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
4 of 38
TDA8025
NXP Semiconductors
IC card interface
7. Pinning information
7.1 Pinning
terminal 1
index area
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
CMDVCCN
TEST1
TEST3
OFFN
RSTIN
TEST2
V
V
DDI(REG)
DD(INTF)
TDA8025
CLKDIV2
CLKDIV1
GND
V
V
DD(INTREGD)
CC
VCC_SEL1
VCC_SEL2
RST
001aai958
Transparent top view
Fig 2. Pin configuration (HVQFN32)
7.2 Pin description
Table 3.
Pin description
Pin Type[1] Description
Symbol
CMDVCCN
TEST1
1
2
3
4
5
I
microcontroller start activation sequence input; active LOW
test pin; connect to GND
I
TEST2
I
test pin; connect to GND
VDD(INTF)
CLKDIV2
P
I
interface supply voltage
sets the clock frequency; used together with pin CLKDIV1;
see Table 4 on page 12
CLKDIV1
6
7
I
I
sets the clock frequency; used together pin CLKDIV2; see Table 4 on
page 12
VCC_SEL1
optional 1.2 V selection control signal:
active HIGH: VCC = 1.2 V
active LOW: disables 1.2 V selection
3 V or 1.8 V selection control signal:
active LOW: VCC = 3 V
VCC_SEL2
8
I
active HIGH: VCC = 1.8 V when pin VCC_SEL1 is active LOW
card presence contact input; active LOW[2]
card presence contact input; active HIGH[2]
card input/output data line (C7)[3]
card auxiliary 2 input/output data line (C8)[3]
card auxiliary 1 input/output data line (C4)[3]
PRESN
PRES
I/O
9
I
I
10
11 I/O
12 I/O
13 I/O
AUX2
AUX1
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
5 of 38
TDA8025
NXP Semiconductors
IC card interface
Table 3.
Pin description …continued
Symbol
CGND
CLK
Pin Type[1] Description
14
15
16
G
O
I
card signal ground
card clock (C3)
CONFIG
3.3 V or 5 V core regulator supply voltage selection; see Figure 3 on
page 7
RST
VCC
17
18
O
P
card reset (C2)
card supply (C1); decouple to pin CGND using one 470 nF and one
220 nF capacitor with an Equivalent Series Resistance
(ESR) < 100 mΩ
VDD(INTREGD) 19
P
G
P
I
internally regulated supply voltage
ground
GND
20
21
22
23
VDDI(REG)
RSTIN
OFFN
regulator input supply voltage
microcontroller card reset input; active HIGH
NMOS interrupt to microcontroller[4]; active LOW; see Section 8.10
on page 19
O
TEST3
24
25
26
27
28
O
I
test pin; do not connect to the application
PORADJ
ENCLKIN
XTAL2
power-on reset threshold adjustment input[4]
enable external clock on pin XTAL1; active HIGH
crystal connection pin; open when used with an external clock source
crystal connection pin; supply reference VDD(INTREGD)
external clock input; supply reference VDD(INTF)
microcontroller input/output data line[4]
microcontroller auxiliary 1 input/output data line[4]
microcontroller auxiliary 2 input/output data line[4]
test pin; connect to GND
I
O
I
XTAL1
I/OUC
29 I/O
30 I/O
31 I/O
AUX1UC
AUX2UC
TEST4
32
I
[1] I = input, O = output, I/O = input/output, G = ground and P = power supply.
[2] If pin PRESN or pin PRES is true, the card is considered to be present. During card insertion, debouncing
can occur on these signals. To counter this, the TDA8025 has a built-in debouncing timer (typically 4.5 ms).
[3] Using the internal pull-up resistor connected to pin VCC
.
[4] Using the internal pull-up resistor connected to pin VDD(INTF)
.
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
6 of 38
TDA8025
NXP Semiconductors
IC card interface
8. Functional description
Remark: Throughout this document the ISO7816 terminology conventions have been
adhered to and it is assumed that the reader is familiar with these.
8.1 Power supplies
Two supply selections can be made using pin CONFIG (see Figure 3) depending on the
active state of the pin:
• pin CONFIG is LOW: supply is pin VDDI(REG). The voltage range of the pin is between
3.6 V and 5.5 V. The regulator output range is between 3 V and 3.6 V.
• pin CONFIG is HIGH: supply pins VDDI(REG) and VDD(INTREGD) are connected together
to bypass the regulator. Pin VDDI(REG) voltage is between 3 V and 3.6 V.
Remark: VDD(INTF) must not exceed VDD(INTREGD) + 0.3 V.
10 µF
10 µF
V
V
DDI(REG)
DDI(REG)
10 µF
100 nF
100 nF
V
V
DD(INTREGD)
DD(INTREGD)
GND CONFIG
20 16
GND CONFIG
20 16
21
19
21
19
REGULATOR
REGULATOR
SUPPLY
SUPPLY
INTERNAL
INTERNAL
REFERENCE
REFERENCE
18
14
V
18
14
V
CC
CC
VOLTAGE
SENSE
V
VOLTAGE
SENSE
V
CC
LOOP
CC
470 nF
220 nF
470 nF
220 nF
LOOP
CGND
CGND
001aai959
001aai960
3.6 V < VDDI(REG) < 5.5 V
3 V < VDD(INTREGD) < 3.6 V
Fig 3. Power strategy
The following examples illustrate the voltage restrictions for VDD(INTF)
.
• CONFIG pin driven to GND: when VDD(INTREGD) is generated by the internal regulator,
VDD(INTF) must not exceed 3.3 V.
• CONFIG pin is driven by VDDI(REG) without VDD(INTF) tied to VDDI(REG) while
VDD(INTREGD) is tied to VDDI(REG): VDD(INTF) must not exceed VDDI(REG) + 0.3 V.
• CONFIG pin is driven by VDDI(REG) with VDD(INTF) tied to both VDDI(REG) and
VDD(INTREGD): there no are restrictions for VDD(INTF)
.
The TDA8025 is held in the reset state until VDD(INTREGD) reaches Vth + Vhys and
PORADJ Vth + Vhys plus the tw(POR) delay. If the VDD(INTREGD) and PORADJ signals fall
below Vth, an automatic contact deactivation is triggered.
All interface signals to the microcontroller are referenced to VDD(INTF). In addition, all card
contacts remain inactive during power-up and power-down cycles.
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
7 of 38
TDA8025
NXP Semiconductors
IC card interface
After powering up the device, pin OFFN remains LOW until pins CMDVCCN and PRES
are both HIGH or pin CMDVCCN is HIGH and pin PRESN is LOW. During power off, pin
OFFN is driven LOW when VDD(INTREGD) is below the falling threshold voltage (Vth).
When pin CMDVCCN is HIGH, the internal oscillator frequency (fosc(int)) is switched to Low
frequency (inactive) mode to reduce power consumption.
8.2 Voltage supervisors
8.2.1 Block diagram
V
DD(INTF)
R1
PORADJ
V
DD(INTREGD)
R2
REFERENCE
VOLTAGE
V
DD(INTREGD)
001aai961
Fig 4. Voltage supervisor circuit
8.2.2 Description
The voltage supervisors provide both the Power-On Reset (POR) and supply drop-out
detection functions. They control the internal regulated supply voltage (VDD(INTREGD)) and
the microcontroller interface supply voltage (VDD(INTF)) to ensure problem-free operation of
the TDA8025.
By monitoring both VDD(INTREGD) and VDD(INTF), the voltage supervisors ensure these
voltages are high enough to ensure correct operation of the TDA8025 and flawless
communication between it and the microcontroller. This information is combined and sent
to the digital controller in order to reset the TDA8025.
An extension of the power-on reset pulse width of ± 8 ms (tw(POR)) is used to maintain the
TDA8025 in inactive mode after the supply voltage power on or off sequences (see
Figure 5).
V
+ V
hys
th
V
th
V
DD(INTREGD)
ALARMN
(internal signal)
t
t
w(POR)
w(POR)
Power on
Supply dropout
Power off
001aai962
Fig 5. Voltage supervisors VDD(INTREGD) and VDD(INTF)
Rev. 01 — 6 April 2009
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
8 of 38
TDA8025
NXP Semiconductors
IC card interface
8.2.3 VDD(INTREGD) voltage supervisor with pin PORADJ connected to VDD(INTF)
The TDA8025 remains in inactive mode irrespective of the levels on the command lines
when
• VDD(INTREGD) is less than Vth + Vhys (on pin VDD(INTREGD)
)
• Pin PORADJ (monitoring VDD(INTF)) is less than Vth + Vhys
In both cases, this lasts for the duration of tw(POR) after VDD(INTREGD) (on pin VDD(INTREGD)
)
and VDD(INTF) (on pin VDD(INTF)) have reached a level higher than Vth + Vhys. Two threshold
voltages (Vth) are set by the hardware as follows:
• VDD(INTREGD) threshold voltage: is set to the minimum supply voltage (2.7 V) specified
for the digital part of the TDA8025
• VDD(INTF) threshold voltage: is set to 1.24 V; see Table 8 on page 23 for detailed
information.
8.2.4 VDD(INTF) voltage supervisor with external divider on pin PORADJ
An external resistor bridge can be used to divide VDD(INTF) on pin PORADJ to adapt the
detection threshold when monitoring the microcontroller interface supply voltage.
Connecting the external resistor bridge as illustrated in Figure 4 on page 8 (R1 connected
to VDD(INTF) and R2 connected to GND) to pin PORADJ overrides the internal threshold
voltage Vth on pin VDD(INTF)
.
The threshold voltage on pin VDD(INTF) is calculated as follows:
1 + R1
R2
Vth on pin VDD(INTF) = Vbg
(1)
---------------
where
• Vbg is the bandgap voltage
When the resistor bridge is not used, pin PORADJ must be connected to pin VDD(INTF)
.
8.2.4.1 R1 and R2 resistor value calculation
This section describes how to calculate the values for resistors R1 and R2, taking into
account the IC detector threshold spread and the external resistance, while ensuring
reliable activation.
If for example, the controller is supplied by a regulator at 3.3 V ± 20 %. Activation can be
triggered above VDD(INTF) = 3.3 V − 20 % (in this example 2.64 V). This activation
threshold is defined as VDD(INTF)actmin; i.e. the minimum value of VDD(INTF) above which
activation can always be triggered.
In addition to this external input, activation is permitted provided all the following
conditions are met (see Table 8 on page 23): card presence, IC temperature, VDD(INTF)
and VDD(INTREGD) supplies, etc.
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
9 of 38
TDA8025
NXP Semiconductors
IC card interface
The voltage on PORADJ (VPORADJ) can be calculated as: VPORADJ = α × VDD(INTF)
where:
• VDD(INTF) is the interface supply voltage
• ratio α
1
α =
(2)
(3)
----------------
R1
R2
1 +
------
An activation can be triggered if
Vth(max)
VDD(INTF) × α > Vth(max) VDD(INTF)
>
-------------------
α
where
• Vth(max) is the maximum rising external threshold voltage
The resistance spread of R1 between a minimum value R1min and a maximum value
R1max induces a spread of the ratio α. This is also true for R2. Based on this:
Vth(max)
VDD(INTF)actmin
=
(4)
(5)
-------------------
αmin
where
1
αmin
=
------------------------
R1max
1 +
--------------
R2min
If ∆R1 is the maximum spread of R1 and ∆R2 is the maximum spread of R2 then:
∆R1
R1max = R1nom + ∆R1 = R1nom 1 +
(6)
(7)
---------------
R1nom
∆R2
R2min = R2nom – ∆R2 = R2nom 1 –
---------------
R2nom
Vth(max)
1
1
αmin
=
=
=
(8)
------------------------------------------------------------
----------------------------------------------
R1nom (1 + β)
---------------------------------------
VDD(INTF)actmin
∆R1
R1nom 1 +
---------------
1 +
-------------------------------------
R1nom
R2nom (1 – β)
1 +
--------------------------------------------------
∆R2
R2nom 1 –
---------------
R2nom
where
• where β is the accuracy ratio of R1 and R2 (R1 and R2 are considered to be of the
same type).
Then
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
10 of 38
TDA8025
NXP Semiconductors
IC card interface
R1nom
V
(1 – β)
----------------
(1 + β)
=
=
DD(INTF)actmin – 1
---------------------------------------
(9)
---------------
R2nom
Vth(max)
Rsum
Rsum
R2nom
=
(10)
------------------------------
--------------------------------------------------------------------------------------------
R1nom
V
(1 – β)
----------------
(1 + β)
1 +
1 +
DD(INTF)actmin – 1
---------------
---------------------------------------
R2nom
Vth(max)
If we target 1 % accuracy resistors (β = 0.01) and Rsum = 100 kΩ; Vth(max) = 1.33 V (see
Table 8 on page 23) and VDD(INTF)actmin = 2.64 V then
• R1nom = 50.88 kΩ
• R2nom = 49.12 kΩ
Deactivation always occurs when
Vth(min)
VPORADJ < Vth(min) VDD(INTF)deactmax
=
(11)
-------------------
αmax
where
• Vth(min) is the minimum falling external threshold voltage
• VDD(INTF)deactmax is the maximum value of VDD(INTF) below which deactivation always
occurs
• αmax
Vth(min)
1
αmax
=
=
(12)
----------------------------------------------
R1nom (1 – β)
---------------------------------------------
VDD(INTF)deactmax
1 +
-------------------------------------
R2nom (1 + β)
With the resulting values for R1nom, R2nom and β; Vth(min) = 1.17 V (see Table 8 on
page 23) then VDD(INTF)deactmax is 2.28 V.
8.3 Clock circuits
The clock signal (pin CLK) to the card is either generated by the clock signal input on pin
XTAL1 or from a crystal (fxtal ≤ 26 MHz) connected between pins XTAL1 and XTAL2. The
voltage level applied to pin ENCLKIN defines which clock signal is used. When pin
ENCLKIN is HIGH, connect the external clock to pin XTAL1.
Driving pin ENCLKIN LOW causes the external crystal to generate frequency fxtal. Using
pins CLKDIV1 and CLKDIV2, the crystal frequency can be set to either fxtal, 1⁄2 fxtal, 1⁄4 fxtal
or 1⁄8 fxtal
.
The frequency change is synchronous and as such during transition, no pulse is shorter
than 45 % of the smallest period. In addition, only the first and last clock pulse around the
change have the correct width. When dynamically changing the frequency, the
modification is only effective after 10 periods of XTAL1.
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
11 of 38
TDA8025
NXP Semiconductors
IC card interface
The duty cycle on pin CLK should be between 45 % and 55 %. To ensure this, the
following must be applied:
• when the CLK frequency is fxtal
:
If an external clock is connected to pin XTAL1, the duty cycle should be between 48 %
and 52 % with an input signal period transition time of less than 5 %.
If a crystal is used to generate fxtal, the duty cycle on pin CLK should be between
45 % and 55 % depending on the layout, crystal characteristics and frequency.
• when CLK frequency is either fxtal, 1⁄2 fxtal, 1⁄4 fxtal or 1⁄8 fxtal
:
The duty cycle is guaranteed between 45 % and 55 % of the period frequency
divisions.
When a crystal is used, it runs when pin ENCLKIN is driven LOW.
CLKDIV1
CLKDIV2
6
5
15 CLK
CLOCK
CIRCUIT
ENCLKIN 26
MULTIPLEXER
XTAL
OSCILLATOR
27
28
XTAL1
XTAL2
(1)
≤ 26 MHz
001aai963
(1) External crystal (optional).
Fig 6. Clock circuits
The clock signal is applied to the card based on the activation sequence as shown on the
timing diagrams; see Figure 8 on page 15 to Figure 13 on page 19.
When the signal applied to XTAL1 is controlled by the microcontroller, the clock signal is
sent to the card only after the activation sequence finishes.
Table 4.
Clock configuration
Clock circuitry definition (pins CLKDIV1 and CLKDIV2 can be changed simultaneously; a
>10 XTAL1 period delay is needed. The minimum duration of any CLK state is 10 XTAL1 periods).
CLKDIV1
CLKDIV2
CLK
0
0
1
1
0
1
1
0
1⁄8 fxtal
1⁄4 fxtal
1⁄2 fxtal
fxtal
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
12 of 38
TDA8025
NXP Semiconductors
IC card interface
8.4 Input and output circuits
When pins I/O and I/OUC are driven HIGH using an 11 kΩ resistor between pins I/O and
VCC and/or between pins I/OUC and VDD(INTF), both lines enter the idle state. Pin I/O is
referenced to VCC and pin I/OUC to VDD(INTF), thus allowing operation at VCC ≠ VDD(INTF)
.
The first side on which a falling edge occurs becomes the master. An anti-latch circuit
disables falling edge detection on the other line, making it the slave. After a time delay
td(edge), the NMOS transistor on the slave-side is turned on. It then sends logic 0 to the
master-side. When the master returns logic 1, the PMOS transistor on the slave side is
turned on during the time delay (tpu). After this sequence, both the master and slave return
to their idle states.
The active pull-up feature ensures fast LOW-to-HIGH transitions making the TDA8025
capable of delivering more than 1 mA, up to an output voltage of 0.9 VCC, at a load of
80 pF. At the end of the active pull-up pulse, the output voltage is dependent on the
internal pull-up resistor value and load current. The current sent to and received from the
card’s I/O lines is internally limited to 15 mA at a maximum frequency of 1 MHz.
001aai964
8
4
I
I/O
(A)
V I/O
(V)
OH
V I/O
6
4
2
0
3
2
1
0
I
I/O
OH
0
20
40
60
80
100
t (ns)
Fig 7. Output voltage and current on pins I/O, AUX1 and AUX2 as a function of time
during LOW-to-HIGH transitions
8.5 Inactive mode
After a power-on reset, the circuit enters the inactive mode, ensuring only the minimum
number of circuits are active while the TDA8025 waits for the microcontroller to start a
session. The inactive mode conditions are as follows:
• all card contacts are inactive. The impedance between the contacts and GND is
approximately 200 Ω.
• pins I/OUC, AUX1UC and AUX2UC are high-impedance using the 11 kΩ pull-up
resistor connected to VDD(INTF)
• the voltage generators and crystal oscillator are stopped
• the voltage supervisor is active
• the internal oscillator runs in low frequency mode
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
13 of 38
TDA8025
NXP Semiconductors
IC card interface
8.6 Activation sequence
After the power-on and internal pulse width delay, the microcontroller checks the presence
of the card using signal OFFN.
• The card is present when pins OFFN and CMDVCCN are HIGH
• The card is not present when pin OFFN is LOW and pin CMDVCCN is HIGH
If the card is in the reader (either pin PRESN or pin PRES is true), the microcontroller can
start a card session by pulling pin CMDVCCN LOW. When using an external crystal, the
following sequence is applied (see Figure 8):
1. pin CMDVCCN is pulled LOW (t0)
2. the crystal oscillator is triggered
3. the internal oscillator changes to its high frequency (t1)
4. VCC rises either from 0 V to 3 V or 1.8 V on a controlled slope (t2)
5. pins I/O, AUX1 and AUX2 which were pulled LOW are driven HIGH (t3)
6. the clock (pin CLK) is applied to the C3 contact (t4)
7. pin RST is enabled (t5)
Calculation of the time delays is as follows:
• t1 = t0 + 2.13 ms
• t2 = t1
• t3 = t1 + 5T/2
• t4 = driven by host controller; > t3 and < t5
• t5 = t1 + 11T/2
Remark: The value of period T is 64 times the period interval of the internal oscillator (i.e.
±25 µs. t3 is called td(start) and t5 is called td(end)
.
The clock is applied to the card in one of the following ways:
• using pin RSTIN: The clock (pin CLK) start-up can be selected at either t3 or t5 using
pin RSTIN. When pin RSTIN is HIGH and pin CMDVCCN is LOW, setting pin RSTIN
to LOW between delays t3 and t5 sends signal CLK. Pin RSTIN should be held LOW
until after delay t5. After passing t5, pin RST is a copy of pin RSTIN and has no further
effect on pin CLK. It enables the microcontroller to precisely choose the CLK start by
counting clock cycles from the falling edge of the RSTIN signal.
• not using pin RSTIN: If this feature is not needed, set both pins CMDVCCN and
RSTIN to LOW. The clock (pin CLK) will start at delay t3 (a minimum 200 ns after the
input/output transition). After delay t5, pin RSTIN can be set HIGH to receive the card
Answer To Request (ATR).
Remark: Do not perform activation with pin RSTIN permanently pulled HIGH.
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
14 of 38
TDA8025
NXP Semiconductors
IC card interface
CMDVCCN
XTAL
V
CC
I/O
ATR
CLK
RSTIN
RST
I/OUC
OSCINT
low frequency
t0 t1 = t2
high frequency
t
t4
t
= t
d(start)
d(end) act
001aai965
Fig 8. Activation sequence: CLK controlled by pin RSTIN with the crystal oscillator
CMDVCCN
XTAL
V
CC
I/O
ATR
CLK
> 200 ns
RSTIN
RST
I/OUC
OSCINT
low frequency
t0 t1 = t2
high frequency
t4
t
= t
d(end) act
t
d(start)
001aai966
Fig 9. Activation sequence: CLK not controlled by pin RSTIN with the crystal oscillator
The following sequence occurs when using an external clock connected to pin XTAL1 (see
Figure 10):
1. external clock (XTAL1) started by the microcontroller (t0)
2. CMDVCCN is pulled LOW and the internal oscillator changes to its high frequency (t1)
3. VCC rises either from 0 V to 3 V or 0 V to 1.8 V on a controlled slope (t2)
© NXP B.V. 2009. All rights reserved.
TDA8025_1
Product data sheet
Rev. 01 — 6 April 2009
15 of 38
TDA8025
NXP Semiconductors
IC card interface
4. pins I/O, AUX1 and AUX2 are enabled (t3)
5. CLK is applied to the C3 contact (t4)
6. pin RST is enabled (t5)
Calculation of the time delays is as follows:
• t1 = t0 + 2.13 ms
• t2 = t1 = 3T/2 + 3(1⁄fosc(int)low
)
• t3 = t1 + 5T/2
• t4 = driven by the host controller; > t3 and < t5
• t5 = t1 + 11T/2
Remark: The value of period T is 64 times the period interval of the internal oscillator (i.e.
±25 µs). t3 is called td(start) and t5 is called td(end). fosc(int)low is the low (or inactive mode)
frequency of the defined fosc(int) parameter.
The CLK is applied to the card under control of pin RSTIN in exactly the same way as with
the crystal oscillator.
Remark: Do not perform activation with pin RSTIN permanently pulled HIGH.
CMDVCCN
XTAL1
V
CC
I/O
ATR
CLK
RSTIN
RST
I/OUC
OSCINT
low frequency
t0 t1 = t2
high frequency
t
t4
t
= t
d(start)
d(end) act
001aai967
Fig 10. Activation sequence: CLK controlled by pin RSTIN with an external clock
connected to pin XTAL1
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
16 of 38
TDA8025
NXP Semiconductors
IC card interface
CMDVCCN
XTAL1
V
CC
I/O
ATR
CLK
> 200 ns
RSTIN
RST
I/OUC
OSCINT
low frequency
t0 t1 = t2
high frequency
t4
t
= t
d(end) act
t
d(start)
001aai968
Fig 11. Activation sequence: CLK not controlled by pin RSTIN and with an external clock
connected to pin XTAL1
8.7 Active mode
When the activation sequence has finished, the TDA8025 is in active mode. This mode
enables data exchange between the card and the microcontroller using the input and
output lines.
Depending on the layout and application test conditions, line C2 could become polluted
with high frequency noise from line C3. For example, due to an additional 1 pF
capacitance between lines C2/C3 and/or lines C2/C7. It is recommended that a 100 pF
capacitor is added between line C2 and pin CGND, if this occurs.
When building the application, the following recommendations should be adhered to:
• Keep track C3 as far away as possible from other tracks.
• Keep the connection between pin CGND and line C5 straight. The two capacitors on
line C1 should be connected to this ground track.
• Do not use ground loops between CGND and GND.
Following these layout recommendations will ensure that noise remains within the
specifications and jitter on line C3 is less than 100 ps.
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
17 of 38
TDA8025
NXP Semiconductors
IC card interface
8.8 Deactivation sequence
When a session is completed, the microcontroller sets pin CMDVCCN to HIGH. The
circuit then executes an automatic deactivation sequence by counting the sequencer back
to the inactive state (see Figure 12 and Figure 13):
1. pin RST is pulled LOW (t11)
2. the clock is stopped, pin CLK is LOW (t12)
3. pins I/O, AUX1 and AUX2 are pulled LOW (t13)
4. VCC falls to zero (t14). The deactivation sequence is completed when VCC reaches its
inactive state
5. all card contacts become low-impedance to GND. However, pins I/OUC, AUX1UC and
AUX2UC remain pulled up to VDD(INTREGD) using the 11 kΩ resistor
6. The internal oscillator returns to its low frequency mode
Calculation of the time delays is as follows:
• t11 = t10 + 3T/64
• t12 = t11 + T/2
• t13 = t11 + T
• t14 = t11 + 3T/2
Remark: The value of period T is 64 times the period interval of the internal oscillator (i.e.
±25 µs).
CMDVCCN
RST
CLK
I/O
V
CC
XTAL
OSCINT
high frequency
low frequency
t10 t11
t12
t
t13
t14
001aai969
deact
Fig 12. Deactivation sequence with a crystal oscillator
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
18 of 38
TDA8025
NXP Semiconductors
IC card interface
CMDVCCN
RST
CLK
I/O
V
CC
XTAL1
OSCINT
high frequency
low frequency
t10 t11
t12
t
t13
t14
001aai970
deact
Fig 13. Deactivation sequence with an external clock connected to pin XTAL1
8.9 VCC regulator
Table 5.
Selection of VCC using pins VCC_SEL1 and VCC_SEL2
VCC_SEL1
VCC_SEL2
VCC
0
0
1
1
0
1
0
1
3 V
1.8 V
1.2 V
1.2 V
The VCC buffer is able to continuously deliver up to:
• 65 mA at 3 V
• 65 mA at 1.8 V
• 30 mA at 1.2 V
The VCC buffer has an internal overload protection with a threshold value of ±135 mA.
This detection is filtered, enabling spurious current pulses up to 200 mA with a duration of
up to 200 ns to be drawn by the card without causing deactivation. However, the average
current value must be below maximum.
To enhance VCC stability, one 470 nF capacitor should be tied to pin CGND near pin 18
and one 220 nF capacitor should be tied to pin CGND near the C1 contact. Both
capacitors should have an ESR < 100 mΩ.
8.10 Fault detection
The following conditions are monitored by the fault detection circuit:
• Short-circuit or high current on pin VCC
• Card removal during transaction
• VDD(INTREGD) falling
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
19 of 38
TDA8025
NXP Semiconductors
IC card interface
• VDD(INTF) falling
• Overheating
Fault detection monitors two different situations (see Figure 15 on page 21):
1. Outside card sessions, pin CMDVCCN is HIGH: pin OFFN is LOW if the card is not in
the reader and HIGH if the card is in the reader. Any supply voltage drop on
VDD(INTREGD) or VDD(INTF) is detected by the supply supervisor. This generates an
internal power-on reset pulse but does not act upon the pin OFFN signal. The card is
not powered-up and as such short-circuits and overheating are not detected.
2. Within card sessions, pin CMDVCCN is LOW: when pin OFFN falls LOW, the fault
detection circuit triggers the automatic emergency deactivation sequence (see
Figure 14). When the system controller resets pin CMDVCCN to HIGH, after the
deactivation sequence, pin OFFN is rechecked. If the card is still present, pin OFFN
returns to HIGH. This check identifies the fault as either a hardware problem or a card
removal incident.
On card insertion or removal, bouncing can occur in the PRES and/or PRESN signals.
This depends on the type of card presence switch in the connector (normally open or
normally closed) and the mechanical characteristics of the switch. To correct for this, a
debouncing feature is integrated in to the TDA8025. This feature operates at a typical
duration of 640 × (1⁄fosc(int)low). See Figure 15 for an overview of the debouncing feature.
Remark: fosc(int)low is the low frequency (or inactive) mode of the defined fosc(int)
parameter.
On card insertion, pin OFFN goes HIGH after the debouncing time has elapsed. When the
card is extracted, the automatic card deactivation sequence is performed on the first true
or false transition on pin PRESN or pin PRES. After this pin OFFN goes LOW.
OFFN
PRESN
RST
CLK
I/O
V
CC
XTAL
OSCINT
high frequency
low frequency
t10
t12
t
t13
t14
001aai971
deact
Fig 14. Emergency deactivation sequence after card removal
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
20 of 38
TDA8025
NXP Semiconductors
IC card interface
PRES
OFFN
CMDVCCN
t
t
deb
deb
(1)
(2)
V
CC
001aai972
(1) Deactivation caused by card removal.
(2) Deactivation caused by short circuit.
Fig 15. Operation of debounce feature pin OFFN in combination with pins CMDVCCN,
PRES and VCC
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
21 of 38
TDA8025
NXP Semiconductors
IC card interface
9. Limiting values
Remark: All card contacts are protected against any short-circuit to any other card
contact. Stress beyond the levels indicated in Table 6 can cause permanent damage to
the device. This is a short-term stress rating only and under no circumstances implies
functional operation under long-term stress conditions.
Table 6.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
Conditions
Min
−0.3
−0.3
−0.3
Max
+5.5
+5.5
+5.5
Unit
V
VDDI(REG)
regulator input supply voltage
VDD(INTREGD) internal regulated supply voltage
V
VI
input voltage
pins CMDVCCN, TEST1, TEST2,
CLKDIV2, CLKDIV1, VCC_SEL1,
VCC_SEL2, CONFIG, RSTIN,
OFFN, TEST3, PORADJ, ENCLKIN,
XTAL2, XTAL1, I/OUC, AUX1UC and
AUX2UC
V
card contact pins PRES, PRESN,
I/O, RST, AUX1, AUX2 and CLK
−0.3
+6.5
V
Tstg
Ptot
Tj
storage temperature
−55
-
+150
0.56
150
+85
+6
°C
W
total power dissipation
junction temperature
Tamb = −25 °C to +85 °C
-
°C
°C
kV
Tamb
VESD
ambient temperature
electrostatic discharge voltage
−25
−6
pins I/O, RST, VCC, AUX1, CLK,
AUX2, PRES and PRESN; within
typical application
Human Body Model (HBM); all pins;
EIA/JESD22-A114-B, June 2000
−2
+2
kV
V
Machine Model (MM); all pins;
−200
+200
EIA/JESD22-A115-A, October 1997
Charged Device Model (CDM);
all pins, except corner pins
−500
−750
+500
+750
V
V
only corner pins (1, 8, 9, 16, 17,
24, 25 and 32)
10. Thermal characteristics
Table 7.
Symbol
Rth(j-a)
Thermal characteristics
Parameter
Conditions
Typ
42
Unit
thermal resistance from junction to ambient
with exposed pad soldered
K/W
K/W
without exposed pad soldered
62
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
22 of 38
TDA8025
NXP Semiconductors
IC card interface
11. Characteristics
Table 8.
Characteristics of IC supply voltage
Tamb = 25 °C; all parameters remain within limits but are only statistically tested for the temperature range; fxtal = 10 MHz; all
currents flowing into the IC are positive; unless otherwise specified. Parameters specified as a function of
VDD(INTF), VDDI(REG), VDD(INTREGD) or VCC refer to the actual value at the time of measurement.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Supply
VDDI(REG)
regulator input
supply voltage
pin CONFIG = ground
3.6
3
5
5.5
3.6
V
V
pin CONFIG = VDDI(REG)
regulator is bypassed
;
3.3
[1]
[2]
VDD(INTREGD) internal
regulated supply
voltage
pin CONFIG = ground
3
3.3
3.6
V
VDD(INTF)
interface supply pin CONFIG = ground
1.6
1.6
3.0
3.0
3.3
V
V
voltage
pin CONFIG = VDDI(REG)
VDDI(REG) + 0.3
and VDD(INTF) not
connected to VDDI(REG)
and VDD(INTREGD)
pin CONFIG = VDDI(REG)
3
3.3
3.6
V
with VDD(INTF) connected
to VDDI(REG) and
VDD(INTREGD)
IDDI(REG)
regulator input
supply current
inactive mode
VDDI(REG) = 5 V
-
-
-
-
300
2.5
µA
f
xtal = stopped
VDDI(REG) = 5 V
mA
f
f
xtal = 10 MHz;
CLK = 1⁄8 fxtal
active mode
VCC = 3 V; ICC = 65 mA
VCC = 1.8 V;
-
-
-
-
85
85
mA
mA
I
CC = 65 mA
VCC = 1.2 V;
CC = 30 mA
-
-
-
-
50
mA
I
IDD(INTF)
Vth
interface supply
current
100
µA
threshold voltage pin VDD(INTREGD); falling
pin VDD(INTREGD); rising
2.60
2.65
1.17
1.19
50
2.70
2.80
1.24
1.26
100
2.80
2.95
1.31
1.33
150
V
V
pin PORADJ; falling
V
pin PORADJ; rising
V
Vhys
hysteresis
voltage
pin VDD(INTREGD)
mV
tw(POR)
∆Vth/∆T
power-on reset
pulse width
5
-
8
-
18
ms
threshold voltage
variation with
temperature
0.25
mV/°C
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
23 of 38
TDA8025
NXP Semiconductors
IC card interface
Table 8.
Characteristics of IC supply voltage …continued
Tamb = 25 °C; all parameters remain within limits but are only statistically tested for the temperature range; fxtal = 10 MHz; all
currents flowing into the IC are positive; unless otherwise specified. Parameters specified as a function of
VDD(INTF), VDDI(REG), VDD(INTREGD) or VCC refer to the actual value at the time of measurement.
Symbol
IL
Parameter
Conditions
Min
−0.1
−1
Typ
+4
-
Max
+10
+1
Unit
µA
leakage current pin PORADJ < 0.5 V
pin PORADJ > 1 V
µA
Card supply voltage[3]
Cdec
decoupling
connected to VCC
550
-
830
nF
capacitance
VCC
supply voltage
including ripple
inactive mode
no load
−0.1
−0.1
-
-
+0.1
+0.3
V
V
ICC = 1 mA
active mode
3 V card:
ICC < 65 mA DC
2.85
2.76
3.05
3.05
3.15
3.20
V
V
single current pulse
−100 mA; 2 µs
current pulses of
40 nAs at
2.76
3.05
3.20
V
ICC < 200 mA;
t < 400 ns
1.8 V card:
I
CC < 65 mA DC
1.71
1.66
1.83
1.83
1.89
1.94
V
V
single current pulse
−100 mA; 2 µs
current pulses of
15 nAs with ICC
1.66
1.83
1.94
V
< 200 mA; t < 400 ns
1.2 V card:
ICC < 30 mA DC
1.1
1.1
1.2
1.2
1.3
1.3
V
V
single current pulse
−100 mA; 2 µs
current pulses of
15 nAs with ICC
< 200 mA; t < 400 ns
1.10
-
1.2
-
1.3
V
Vripple(p-p)
ICC
peak-to-peak
ripple voltage
pin VCC; 20 kHz to
200 MHz
350
mV
supply current
0 V to 3 V
-
-
65
mA
mA
mA
V/µs
0 V to 1.8 V
0 V to 1.2 V
up or down
-
-
65
-
-
30
SR
slew rate
0.02
0.14
0.26
Crystal oscillator: pins XTAL1 and XTAL2
Cext
external
pins XTAL1/XTAL2;
-
-
15
pF
capacitance
depending on the crystal
or resonator specification
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
24 of 38
TDA8025
NXP Semiconductors
IC card interface
Table 8.
Characteristics of IC supply voltage …continued
Tamb = 25 °C; all parameters remain within limits but are only statistically tested for the temperature range; fxtal = 10 MHz; all
currents flowing into the IC are positive; unless otherwise specified. Parameters specified as a function of
VDD(INTF), VDDI(REG), VDD(INTREGD) or VCC refer to the actual value at the time of measurement.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
fxtal
fext
VIL
VIH
crystal frequency card clock reference;
crystal oscillator
2
-
26
MHz
external
frequency
external clock on
pin XTAL1
0
-
-
26
MHz
V
LOW-level input pin XTAL1
voltage
−0.3
+0.3VDD(INTF)
HIGH-level input pin XTAL1
voltage
VDD(INTF)
≤
0.7VDD(INTF)
0.7VDD(INTF)
-
-
VDD(INTF) + 0.3
V
V
VDD(INTREGD)
VDD(INTF)
VDD(INTREGD)
Data lines: pins I/O, I/OUC, AUX1, AUX2, AUX1UC and AUX2UC
>
VDD(INTREGD)
0.3
+
td
delay time
falling edge on pins I/O
and I/OUC or vise versa
-
-
-
-
-
-
-
-
200
100
1
ns
tw(pu)
fio
pull-up pulse
width
ns
input/output
frequency
on data lines
on data lines
MHz
pF
Ci
input
10
capacitance
Data lines to the card: pins I/O, AUX1 and AUX2[4]
Vo
output voltage
output current
inactive mode
no load
0
-
-
-
-
0.1
0.3
−1
V
Io = 1 mA
V
Io
from data lines when in
inactive mode with pins
grounded
-
mA
VOL
LOW-level output IOL = 1 mA
voltage
0
-
-
-
-
-
0.3
V
V
V
V
V
IOL ≥ 15 mA
V
CC − 0.4
VCC
VOH
HIGH-level
no DC load
0.9VCC
VCC + 0.1
VCC + 0.1
VCC + 0.1
output voltage
IOH < −40 µA; 3 V
0.75VCC
0.75VCC
IOH < −20 µA; 1.8 V or
1.2 V card
current limit IOH = −15 mA
0
-
-
-
-
-
0.4
V
V
V
V
V
VIL
LOW-level input VCC = +3 V
−0.3
−0.3
−0.3
0.6VCC
+0.8
voltage
VCC = +1.8 V
+0.6
VCC = +1.2 V
+0.4
VIH
HIGH-level input
voltage
VCC + 0.3
Vhys
IIL
hysteresis
voltage
pin I/O
-
-
350
-
-
mV
LOW-level input pin I/O; VIL = 0 V
current
600
µA
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
25 of 38
TDA8025
NXP Semiconductors
IC card interface
Table 8.
Characteristics of IC supply voltage …continued
Tamb = 25 °C; all parameters remain within limits but are only statistically tested for the temperature range; fxtal = 10 MHz; all
currents flowing into the IC are positive; unless otherwise specified. Parameters specified as a function of
VDD(INTF), VDDI(REG), VDD(INTREGD) or VCC refer to the actual value at the time of measurement.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
IIH
HIGH-level input pin I/O; VIH = VCC
current
-
-
10
µA
tr(i)
tr(o)
tf(i)
input rise time
VIL maximum to
IH minimum
-
-
1.2
0.1
1.2
0.1
13
µs
µs
µs
µs
kΩ
mA
V
output rise time CL ≤ 80 pF; 10 % to 90 %;
-
-
0 V to VCC
input fall time
VIL maximum to
IH minimum
-
-
V
tf(o)
Rpu
IOH
output fall time
CL ≤ 80 pF; 10 % to 90 %;
0 V to VCC
-
-
pull-up
resistance
between I/O and VCC
8
−8
11
−6
HIGH-level
pin I/O when active
−4
output current
pull-up; VOH = 0.9VCC
C = 80 pF
;
Data lines to the system: pins I/OUC, AUX1UC and AUX2UC[5]
VOL
LOW-level output IOL = 1 mA
voltage
0
-
0.3
V
VOH
HIGH-level
output voltage
no DC load
OH ≤ 40 µA;
DD(INTF) > 2 V
OH ≤ 20 µA;
DD(INTF) < 2 V
0.9VDD(INTF)
-
-
VDD(INTF) + 0.1
VDD(INTF) + 0.1
V
V
I
V
0.75VDD(INTF)
I
V
0.75VDD(INTF)
-
VDD(INTF) + 0.1
V
VIL
VIH
Vhys
IIH
LOW-level input
voltage
−0.3
-
+0.3VDD(INTF)
V
HIGH-level input
voltage
0.7VDD(INTF)
-
VDD(INTF) + 0.3
V
hysteresis
voltage
pin I/OUC
-
-
-
8
-
-
-
-
0.19VDD(INTF)
-
V
HIGH-level input pin I/OUC; VIH = VDD(INTF)
current
-
10
600
13
1.2
0.1
1.2
0.1
µA
µA
kΩ
µs
µs
µs
µs
IIL
LOW-level input pin I/OUC; VIL = 0 V
current
-
Rpu
tr(i)
tr(o)
tf(i)
pull-up
resistance
between I/OUC and
VDD(INTF)
11
-
input rise time
VIL maximum to
VIH minimum
output rise time CL ≤ 80 pF;10 % to 90 %;
-
0 V to VCC
input fall time
VIL maximum to
IH minimum
-
V
tf(o)
output fall time
CL ≤ 80 pF; 10 % to 90 %;
-
0 V to VCC
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
26 of 38
TDA8025
NXP Semiconductors
IC card interface
Table 8.
Characteristics of IC supply voltage …continued
Tamb = 25 °C; all parameters remain within limits but are only statistically tested for the temperature range; fxtal = 10 MHz; all
currents flowing into the IC are positive; unless otherwise specified. Parameters specified as a function of
VDD(INTF), VDDI(REG), VDD(INTREGD) or VCC refer to the actual value at the time of measurement.
Symbol
IOH
Parameter
Conditions
Min
Typ
Max
Unit
HIGH-level
pin I/OUC when active
−1
-
-
mA
output current
pull-up; VOH = 0.9VDD
C = 30 pF
;
Internal oscillator
fosc(int) internal oscillator inactive mode
55
140
2.7
200
3.2
kHz
frequency
active mode
1.9
MHz
Reset output to the card: pin RST
Vo
output voltage
inactive mode
no load
0
-
-
-
-
0.1
0.3
−1
V
Io = 1 mA
V
Io
output current
delay time
when inactive and pin
RST grounded
0
mA
td
between pins RSTIN and
RST; RST enabled
-
-
2
µs
VOL
LOW-level output IOL = 200 µA
0
-
-
-
-
-
0.2
V
voltage
current limit IOL = 20 mA
IOH = −200 µA
V
CC − 0.4
VCC
VCC
0.4
V
VOH
HIGH-level
0.9VCC
V
output voltage
current limit IOH = −20 mA
0
-
V
[6]
[6]
tr
tf
rise time
fall time
CL = 100 pF;
V
0.1
µs
CC = 3 V, 1.8 V or 1.2 V
CL = 100 pF;
CC = 3 V, 1.8 V or 1.2 V
Clock output to the card: pin CLK
-
-
0.1
µs
V
Vo
output voltage
output current
inactive mode
no load
0
-
-
-
-
0.1
0.3
−1
V
Io = 1 mA
V
Io
pin CLK when inactive
and grounded
0
mA
VOL
LOW-level output IOL = 200 µA
0
-
-
-
-
-
-
-
-
0.3
VCC
VCC
0.4
16
V
voltage
current limit IOL = 70 mA
IOH = −200 µA
V
CC − 0.4
V
VOH
HIGH-level
0.9VCC
V
output voltage
current limit IOH = −70 mA
CL = 30 pF
0
V
[6]
[6]
[6]
tr
rise time
fall time
-
ns
ns
%
V/ns
tf
CL = 30 pF
-
16
δ
duty cycle
slew rate
except for fxtal; CL = 30 pF
rise and fall; CL = 30 pF;
45
0.2
55
SR
-
VCC = 3 V or 1.8 V
CL = 30 pF; VCC = 1.2 V
0.1
-
-
V/ns
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
27 of 38
TDA8025
NXP Semiconductors
IC card interface
Table 8.
Characteristics of IC supply voltage …continued
Tamb = 25 °C; all parameters remain within limits but are only statistically tested for the temperature range; fxtal = 10 MHz; all
currents flowing into the IC are positive; unless otherwise specified. Parameters specified as a function of
V
DD(INTF), VDDI(REG), VDD(INTREGD) or VCC refer to the actual value at the time of measurement.
Symbol Parameter Conditions Min Typ
Control inputs: pins CLKDIV1, CLKDIV2, CMDVCCN, RSTIN, VCC_SEL2, VCC_SEL1 and ENCLKIN[7]
Max
Unit
VIL
VIH
Vhys
IIL
LOW-level input
voltage
−0.3
-
+0.3VDD(INTF)
V
HIGH-level input
voltage
0.7VDD(INTF)
-
VDD(INTF) + 0.3
V
hysteresis
voltage
control inputs
-
-
-
0.14VDD(INTF)
-
V
LOW-level input VIL = 0 V
current
-
-
1
1
µA
µA
IIH
HIGH-level input VIH = VDD(INTF)
current
Control inputs CMDVCCN and CONFIG[7]
fCMDVCCN
frequency on pin
CMDVCCN
-
-
150
kHz
V
VIL
LOW-level input
voltage
−0.3
-
+0.3VDD(INTF)
VIH
HIGH-level input
voltage
0.7
-
VDD(INTREGD)
0.3
+
V
VDD(INTREGD)
Vhys
IIL
hysteresis
voltage
pin CONFIG
-
-
-
0.14VDD(INTF)
-
V
LOW-level input VIL = 0 V
current
-
-
1
1
µA
µA
IIH
HIGH-level input VIH = VDD(INTREGD)
current
Card detection inputs: pins PRES and PRESN[7][8][9]
VIL
VIH
Vhys
IIL
LOW-level input
voltage
−0.3
-
-
+0.3VDD(INTREGD)
V
HIGH-level input
voltage
0.7
VDD(INTREGD)
0.3
+
V
VDD(INTREGD)
hysteresis
voltage
pins PRES and PRESN
-
-
-
0.17
VDD(INTREGD)
-
V
LOW-level input VIL = 0 V
current
-
5
5
µA
µA
IIH
HIGH-level input VIH = VDD(INTREGD)
current
-
OFFN output[10]: pin OFFN
VOL
VOH
Rpu
LOW-level output IOL = 2 mA
voltage
0
-
0.3
-
V
HIGH-level
IOH = −15 µA
0.75VDD(INTF)
16
-
V
output voltage
pull-up
to VDD
20
24
kΩ
resistance
[1] Two decoupling capacitors connected in parallel to VDD(INTREGD) rated at 100 nF and 1 µF.
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
28 of 38
TDA8025
NXP Semiconductors
IC card interface
[2] To enable the microcontroller to provide the required maximum voltage input level on XTAL1, VDD(INTF) must not exceed
VDD(INTREGD) + 0.3 V. See Section 8.1 on page 7 for specific limitations on the maximum VDD(INTF) voltage and Table 8 on page 23 for
the limits of XTAL1.
[3] To meet these specifications, VCC should be decoupled to pin CGND using two low ESR, ceramic multilayer capacitors one of 470 nF
and one of 220 nF with an ESR of < 100 mΩ.
[4] Using the internal pull-up resistor to VCC
.
[5] Using the internal pull-up resistor to VDD(INTF)
.
[6] The transition time and the duty factor definitions are shown in Figure 16 on page 30; δ = t1/(t1 + t2).
[7] Pins PRESN and CMDVCCN are active LOW. Pins RSTIN and PRES are active HIGH; see Table 4 on page 12 for pins CLKDIV1 and
CLKDIV2; see Table 5 on page 19 for pins VCC_SEL1 and VCC_SEL2.
[8] If PRESN or PRES is true, the card is considered to be present. A debouncing feature of 4.5 ms typical is built-in.
[9] Pin PRES has an integrated current source to pin GND, pin PRES to VDD(INTREGD); the card is considered as present if at least one of
the two inputs is true.
[10] Pin OFFN is an NMOS drain, using an internal pull-up resistor to VDD(INTREGD)
.
Table 9.
Symbol
ICC
Protection characteristics
Parameter
Conditions
Min
Typ
Max
Unit
supply current
shutdown current on
pin VCC
95
135
185
mA
pin VCC
pin CLK
pin RST
135
−70
−20
−15
175
225
+70
+20
+15
mA
mA
mA
mA
-
-
-
IIO
input/output current
pins I/O, AUX1 and
AUX2
Tsd
shutdown temperature
-
150
-
°C
Table 10. Timing characteristics
Symbol
Parameter
Conditions
Min
35
Typ
Max
3000
240
Unit
[1]
[2]
[3]
tact
activation time
total sequence with the crystal oscillator
external clock
-
µs
µs
µs
35
-
tdeact
td
deactivation time
delay time
total sequence
35
80
100
CLK sent to a card with the crystal oscillator
td(start) = t3
[1]
[1]
35
-
-
3000
3090
µs
µs
td(end) = t5
160
CLK sent to card using an external clock
td(start) = t3
[2]
[2]
[4]
35
-
150
240
12
µs
µs
ms
td(end) = t5
160
3.2
-
tdeb
debounce time
on pins PRES and PRESN
4.5
[1] See Figure 8 on page 15.
[2] See Figure 10 on page 16.
[3] See Figure 12 on page 18.
[4] See Figure 15 on page 21.
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
29 of 38
TDA8025
NXP Semiconductors
IC card interface
t
t
f
r
V
OH
90 %
90 %
(V
+ V )/2
OL
OH
10 %
10 %
V
OL
001aai973
t1
t2
Fig 16. Definition of output and input transition times
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
30 of 38
TDA8025
NXP Semiconductors
IC card interface
12. Application information
V
MICROCONTROLLER
DD(INTF)
V
DD(INTF)
R1
V
DD(INTF)
R2
V
DD(INTF)
32 31 30 29 28 27 26 25
CMDVCCN
TEST1
TEST3
OFFN
RSTIN
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
V
DDI(REG)
TEST2
C5
100 nF
C3
V
V
DDI(REG)
DD(INTF)
10 µF
TDA8025
CLKDIV2
CLKDIV1
GND
V
V
DD(INTREGD)
CC
C4
VCC_SEL1
VCC_SEL2
100 nF
RST
9
10 11 12 13 14 15 16
C1
470 nF
V
DD(INTREGD)
CARD
CONNECTOR
C2
220 nF
C5
C1
C2
C3
C4
K1
C6
C7
C8
K2
RD Ω
V
DDI(REG)
001aai974
Refer to Table 8 on page 23 and Section 8.1 “Power supplies” on page 7 for detailed information on
the VDD(INTF) restrictions.
Fig 17. Application diagram (3 V < VDDI(REG) < 3.6 V)
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
31 of 38
TDA8025
NXP Semiconductors
IC card interface
V
MICROCONTROLLER
DD(INTF)
V
DD(INTF)
R1
V
DD(INTF)
R2
V
DD(INTF)
32 31 30 29 28 27 26 25
CMDVCCN
TEST1
TEST3
OFFN
RSTIN
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
V
DDI(REG)
TEST2
C5
100 nF
C3
V
V
DDI(REG)
DD(INTF)
10 µF
TDA8025
CLKDIV2
CLKDIV1
GND
V
V
DD(INTREGD)
CC
C3
VCC_SEL1
VCC_SEL2
10 µF
RST
C4
9
10 11 12 13 14 15 16
C1
470 nF
100 nF
CARD
CONNECTOR
C2
220 nF
C5
C1
C2
C3
C4
K1
C6
C7
C8
K2
RD Ω
V
DDI(REG)
001aaj350
Refer to Table 8 on page 23 and Section 8.1 “Power supplies” on page 7 for detailed information on
the VDD(INTF) restrictions.
Fig 18. Application diagram (3.6 V < VDDI(REG) < 5.5 V)
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
32 of 38
TDA8025
NXP Semiconductors
IC card interface
13. Package outline
HVQFN32: plastic thermal enhanced very thin quad flat package; no leads;
32 terminals; body 5 x 5 x 0.85 mm
SOT617-1
B
A
D
terminal 1
index area
A
A
1
E
c
detail X
C
e
1
y
y
e
1/2 e
v
M
M
b
C
C
A B
C
1
w
9
16
L
17
8
e
e
E
h
2
1/2 e
1
24
terminal 1
index area
32
25
X
D
h
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
(1)
A
(1)
(1)
UNIT
A
b
c
E
e
e
e
2
y
D
D
E
L
v
w
y
1
1
h
1
h
max.
0.05 0.30
0.00 0.18
5.1
4.9
3.25
2.95
5.1
4.9
3.25
2.95
0.5
0.3
mm
0.05 0.1
1
0.2
0.5
3.5
3.5
0.1
0.05
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
PROJECTION
ISSUE DATE
VERSION
IEC
JEDEC
JEITA
01-08-08
02-10-18
SOT617-1
- - -
MO-220
- - -
Fig 19. Package outline SOT617-1
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
33 of 38
TDA8025
NXP Semiconductors
IC card interface
14. Soldering of SMD packages
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description”.
14.1 Introduction to soldering
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
14.2 Wave and reflow soldering
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
• Through-hole components
• Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
• Board specifications, including the board finish, solder masks and vias
• Package footprints, including solder thieves and orientation
• The moisture sensitivity level of the packages
• Package placement
• Inspection and repair
• Lead-free soldering versus SnPb soldering
14.3 Wave soldering
Key characteristics in wave soldering are:
• Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
• Solder bath specifications, including temperature and impurities
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
34 of 38
TDA8025
NXP Semiconductors
IC card interface
14.4 Reflow soldering
Key characteristics in reflow soldering are:
• Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 20) than a SnPb process, thus
reducing the process window
• Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
• Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak
temperature is high enough for the solder to make reliable solder joints (a solder paste
characteristic). In addition, the peak temperature must be low enough that the
packages and/or boards are not damaged. The peak temperature of the package
depends on package thickness and volume and is classified in accordance with
Table 11 and 12
Table 11. SnPb eutectic process (from J-STD-020C)
Package thickness (mm) Package reflow temperature (°C)
Volume (mm3)
< 350
235
≥ 350
220
< 2.5
≥ 2.5
220
220
Table 12. Lead-free process (from J-STD-020C)
Package thickness (mm) Package reflow temperature (°C)
Volume (mm3)
< 350
260
350 to 2000
> 2000
260
< 1.6
260
250
245
1.6 to 2.5
> 2.5
260
245
250
245
Moisture sensitivity precautions, as indicated on the packing, must be respected at all
times.
Studies have shown that small packages reach higher temperatures during reflow
soldering, see Figure 20.
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
35 of 38
TDA8025
NXP Semiconductors
IC card interface
maximum peak temperature
= MSL limit, damage level
temperature
minimum peak temperature
= minimum soldering temperature
peak
temperature
time
001aac844
MSL: Moisture Sensitivity Level
Fig 20. Temperature profiles for large and small components
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description”.
15. Abbreviations
Table 13. Abbreviations
Acronym
ATR
Description
Answer To Request
ESD
ElectroStatic Discharge
ESR
Equivalent Series Resistance
Negative-channel Metal-Oxide Semiconductor
Power-On Reset
NMOS
POR
PMOS
Positive-channel Metal-Oxide Semiconductor
16. Revision history
Table 14. Revision history
Document ID
Release date
20090406
Data sheet status
Change notice
Supersedes
TDA8025_1
Product data sheet
-
-
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
36 of 38
TDA8025
NXP Semiconductors
IC card interface
17. Legal information
17.1 Data sheet status
Document status[1][2]
Product status[3]
Development
Definition
Objective [short] data sheet
This document contains data from the objective specification for product development.
This document contains data from the preliminary specification.
This document contains the product specification.
Preliminary [short] data sheet Qualification
Product [short] data sheet Production
[1]
[2]
[3]
Please consult the most recently issued document before initiating or completing a design.
The term ‘short data sheet’ is explained in section “Definitions”.
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
17.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
Terms and conditions of sale — NXP Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
terms and conditions, the latter will prevail.
17.3 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such
information and shall have no liability for the consequences of use of such
information.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from national authorities.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
17.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
18. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
TDA8025_1
© NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 6 April 2009
37 of 38
TDA8025
NXP Semiconductors
IC card interface
19. Contents
1
2
3
4
5
6
General description . . . . . . . . . . . . . . . . . . . . . . 1
19
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Quick reference data . . . . . . . . . . . . . . . . . . . . . 2
Ordering information. . . . . . . . . . . . . . . . . . . . . 3
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4
7
7.1
7.2
Pinning information. . . . . . . . . . . . . . . . . . . . . . 5
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5
8
8.1
8.2
8.2.1
8.2.2
8.2.3
Functional description . . . . . . . . . . . . . . . . . . . 7
Power supplies . . . . . . . . . . . . . . . . . . . . . . . . . 7
Voltage supervisors . . . . . . . . . . . . . . . . . . . . . 8
Block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . 8
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
VDD(INTREGD) voltage supervisor with
pin PORADJ connected to VDD(INTF) . . . . . . . . 9
8.2.4
VDD(INTF) voltage supervisor with external
divider on pin PORADJ. . . . . . . . . . . . . . . . . . . 9
R1 and R2 resistor value calculation . . . . . . . . 9
Clock circuits. . . . . . . . . . . . . . . . . . . . . . . . . . 11
Input and output circuits . . . . . . . . . . . . . . . . . 13
Inactive mode . . . . . . . . . . . . . . . . . . . . . . . . . 13
Activation sequence . . . . . . . . . . . . . . . . . . . . 14
Active mode . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Deactivation sequence . . . . . . . . . . . . . . . . . . 18
8.2.4.1
8.3
8.4
8.5
8.6
8.7
8.8
8.9
VCC regulator . . . . . . . . . . . . . . . . . . . . . . . . . 19
8.10
Fault detection . . . . . . . . . . . . . . . . . . . . . . . . 19
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 22
Thermal characteristics. . . . . . . . . . . . . . . . . . 22
Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . 23
Application information. . . . . . . . . . . . . . . . . . 31
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 33
9
10
11
12
13
14
Soldering of SMD packages . . . . . . . . . . . . . . 34
Introduction to soldering . . . . . . . . . . . . . . . . . 34
Wave and reflow soldering . . . . . . . . . . . . . . . 34
Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 34
Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 35
14.1
14.2
14.3
14.4
15
16
Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 36
Revision history. . . . . . . . . . . . . . . . . . . . . . . . 36
17
Legal information. . . . . . . . . . . . . . . . . . . . . . . 37
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 37
Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 37
17.1
17.2
17.3
17.4
18
Contact information. . . . . . . . . . . . . . . . . . . . . 37
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2009.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
Date of release: 6 April 2009
Document identifier: TDA8025_1
相关型号:
©2020 ICPDF网 联系我们和版权申明