LV52204MTTBG [ONSEMI]
LED Boost Driver;![LV52204MTTBG](http://pdffile.icpdf.com/pdf2/p00340/img/icpdf/LV52204MT_2093798_icpdf.jpg)
型号: | LV52204MTTBG |
厂家: | ![]() |
描述: | LED Boost Driver 驱动 信息通信管理 光电二极管 接口集成电路 |
文件: | 总16页 (文件大小:445K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
Ordering number : ENA2184B
LV52204MT
Bi-CMOS IC
http://onsemi.com
LED Boost Driver with PWM
and 1-Wire Dimming
Overview
The LV52204MT is a high voltage boost driver for LED drive.
LED current is set by the external resistor R1 and LED dimming
can be done by changing FB voltage with PWM or 1-Wire.
Features
• Operating Voltage from 2.7V to 5.5V
• 1-Wire 32 level digital and PWM dimming
• Integrated 40V MOSFET
• 600kHz Switching Frequency
WDFN6 2x2, 0.65P
Typical Applications
• LED Display Backlight Control
D1
L1
22μH
VBAT
C1
1μF
C2
1μF
PWM/
1-WIRE
LV52204
C3
220nF
R1
10Ω
ORDERING INFORMATION
See detailed ordering and shipping information on page 16 of this data sheet.
Semiconductor Components Industries, LLC, 2014
May, 2014
51914NK/O1613NK 20130917-S00002/52213NK No.A2184-1/16
LV52204MT
Specifications
Absolute Maximum Ratings at Ta = 25°C
Parameter
Symbol
Conditions
Ratings
Unit
V
Maximum supply voltage
Maximum pin voltage1
Maximum pin voltage2
Allowable power dissipation
Operating temperature
Storage temperature
V
max
CC
V
6.0
40
CC
V1 max
V2 max
Pd max
Topr
SW
V
Other pin
Ta = 25°C *1
5.5
V
2.05
W
°C
°C
-30 to +85
-55 to +125
Tstg
*1 Mounted on a specified board: 70mm×50mm×1.2mm (4 layer glass epoxy)
Caution 1) Absolute maximum ratings represent the values which cannot be exceeded for any length of time.
Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current,
high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details.
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed,
damage may occur and reliability may be affected.
Recommendation Operating Condition at Ta = 25°C
Parameter
Supply voltage range1
PWM frequency
Symbol
Conditions
Ratings
Unit
V
V
op
V
2.7 to 5.5
CC
CC
PWM MODE
Fpwm
Fduty
300 to 100k
Hz
%
PWM minimum duty
10kHz, VIN ≥3.3V, –30°C to 85°C *2
20kHz, VIN ≥3.3V, –30°C to 85°C *2
30kHz, VIN ≥3.3V, –30°C to 85°C *2
2
4
6
%
%
*2 Guaranteed by design
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended
Operating Ranges limits may affect device reliability.
Electrical Characteristics Analog block at Ta = 25°C, V
= 3.6V, unless otherwise specified
CC
Ratings
Parameter
Symbol
Conditions
Unit
min
typ
max
Standby current dissipation
DC/DC current dissipation
FB voltage
I
I
1
2
SHUTDOWN
= 30V, I
0
0.2
38
5
1
μA
mA
V
CC
V
= 20mA
LED
CC
OUT
Vfb
Ifb
PWM duty 100%
0.19
0.21
1
FB pin leak current
OVP voltage
μA
V
Vovp
Ron
SW
37
39
SWOUT ON resistance
NMOS switch current limit
OSC frequency
IL = 100mA
Vfb = 200mV
700
0.7
mΩ
A
ILIM
Fosc
600
kHz
V
High level input voltage
Low level input voltage
Under voltage lockout
V
V
H
L
SWIRE
SWIRE
1.5
0
V
IN
CC
0.4
V
IN
Vuvlo
Vack
V
falling
2.2
V
IN
Rpullup = 15kΩ
SWIRE output voltage
for Acknowledge
0.4
V
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be
indicated by the Electrical Characteristics if operated under different conditions.
No.A2184-2/16
LV52204MT
Recommended SWIRE Timing at Ta = 25°C, V
= 3.6V, unless otherwise specified
CC
Ratings
typ
Parameter
Symbol
Ton1
Conditions
Unit
min
max
SWIRE setup time1
from shutdown
PWM duty more than 2%,
2
20
1
μs
VIN ≥3.3V, –30°C to 85°C *3
SWIRE setup time2
from shutdown
Ton2
μs
SWIRE mode selectable time
Tsel
Tw0
2.2
ms
SWIRE delay time to start
digital mode detection
SWIRE low time to switch to
digital mode
100
μs
Tw1
260
μs
SWIRE low time to shutdown
Toff
8.9
2
ms
SWIRE start time for digital
mode programming
Tstart
μs
SWIRE end time for digital
mode programming
Tend
2
360
μs
SWIRE High time of bit 0
Th0
Tl0
Bit detection = 0
Bit detection = 0
Bit detection = 1
Bit detection = 1
2
Th0 × 2
Tl1 × 2
2
180
360
360
180
μs
μs
μs
μs
ms
μs
μs
SWIRE Low time of bit 0
SWIRE High time of bit 1
SWIRE Low time of bit1
DCDC startup delay
Th1
Tl1
Tdel
Tackd
Tack
2
Delay time of Acknowledge
Duration of Acknowledge
2
512
*3 Guaranteed by design
Block Diagram
VBAT
SW
4
V
CC
6
UVLO
TSD
OCP
OVP
600kHz PWM
Controler
FB
1
3
SWIRE
FCAP
5
2
PWM/
1-Wire
VREF
CONTROL
VREF
GND
No.A2184-3/16
LV52204MT
Pin Connections
FB 1
FCAP 2
GND 3
6 VIN
5 SWIRE/PWM
4 SW
Top view
Pin Function
PIN #
Pin Name
Description
1
2
3
4
5
6
FB
Feedback pin.
FCAP
GND
SW
Filtering capacitor terminal for PWM mode.
Ground
Switch pin. Drain of the internal power FET.
1-wire dimming control and PWM dimming input (active High).
Supply voltage.
SWIRE
V
CC
Expose-pad
Connect to GND on PCB.
Pd max -- Ta
Mounted on a specified board: 70×50×1.2mm3
(4 layer glass epoxy)
3.0
2.05
2.0
1.0
0.82
0
--30
0
30
60
90
120
Ambient temperature, Ta -- °C
No.A2184-4/16
LV52204MT
LED Current Setting
LED current is set by an external resistor connected between the FB pin and ground.
I
= V /R .
FB FB
LED
The V can be controled by two dimming modes, PWM Mode or Digital Mode.In PWM mode, PWM input is
FB
converted into a near DC current by the internal resistor R that was equivalent to 60kΩ (±10%) and the external
capacitor C
as a low pass filter with a cut-off frequency fc = 1/2πR
. The V can be adjusted by altering
FCAP
FCAP
FB
the duty cycle of the PWM signal (See Fig.1).
= 200 (mV) × PWM Duty (%)
V
FB
On the other hand, V can be selected one from among 32steps in Digital Mode (See Fig.2).
FB
200
180
160
140
120
100
80
200
180
160
140
120
100
80
60
60
40
40
20
0
20
0
0
10
20
30
40
50
60
70
80
90
100
0
2
4
6
8
10 12 14 16 18 20 22 24 26 28 30 32
PWM Duty (%)
Data
Fig1. V
FB
vs. PWM Duty (PWM mode)
Fig2. V
vs. Data Register Value (Digital mode)
FB
Dimming Mode Selection
Dimming Mode is selected by a specific pattern of the SWIRE within Tsel (1ms) from the startup of the device every
time. In order to startup the device, the SWIRE must keep high for longer than Ton.
PWM Mode
The dimming mode is set to PWM mode when it is not recognized as a digital mode within Tsel. To enter Digital Mode,
the SWIRE is required keeping in low state for Tw1 (See Fig.4). If the PWM frequency is used faster than 6.6kHz, the
dimming mode is set to PWM mode only. But slower than 6.6kHz, it is necessary to avoid entering the digital mode
condition, such as SWIRE keeps high for longer than Tsel. PWM is enabled after Tdel from Tsel.
Tsel
Tdel
Ton
Toff
Shutdown
SWIRE
(PWM Freq > 6.6kHz)
PWM Enable
Tsel
Tdel
Toff
Shutdown
SWIRE
(PWM Freq < 6.6kHz)
PWM Enable
Fig3. SWIRE Timing Diagram in PWM mode
No.A2184-5/16
LV52204MT
Digital Mode
To enter Digital Mode, SWIRE should be taken high for more than Tw0 (100μs) from the first rising edge and keep low
state for Tw1(260μs) before Tsel(1ms).
Tdel
Tsel
Tw1
Toff
Shutdown
Tw0
Shutdown
SWIRE
Device Address & data
Device Address & data
Digital Mode
Fig4. SWIRE Timing Diagram in Digital mode
It is required sending the device address byte and the data byte to select V . The bit detection is determined by the
FB
ratio of Th and Tl (See Fig6). The start condition for the bit transmission required SWIRE high for at least Tstart. The
end condition is required SWIRE low for at least Tend.When data is not being transferred, SWIRE is set in the “H” state.
These registers are initialized with POR (Power On Reset).
In the LV52204MT, the device address (DA7 to DA0) is specified as “01110010”. D7 is setting for the acknowledge
response. If the device address and the data byte are transferred on D7 = 1, the ACK signal is sent from the receive side
to the send side. The acknowledge signal is issued when SWIRE on the send side is released and SWIRE on the receive
side is set to low state. D6 and D5 need to send 0. D4 to D0 allow to changing the FB voltage.
Register
DA7
BIT
7
Description
0
1
1
1
0
0
1
0
DA6
6
DA5
5
DA4
4
Device
Address
DA3
3
DA2
2
DA1
1
DA0
0
Table1. Device Address Description
Register
D7
BIT
Description
0 = Acknowledge disabled
1 = Acknowledge enabled
7
D6
D5
D4
D3
D2
D1
D0
6
5
4
3
2
1
0
0
0
Data bit 4
Data bit 3
Data bit 2
Data bit 1
Data bit 0
Data
Table2. Data Description
FB Voltage Control
FB Voltage Control
S
S
0
0
1
1
1
1
0
0
1
0
E
E
S
0
0
0
E
E
Device Address
ACK:Disable
1
1
0
0
1
0
S
1
0
0
A
Device Address
Start Condition
ACK:Enable
End Condition
S
E
A
Acknowledge
Fig5. Example of writing data
No.A2184-6/16
LV52204MT
Tstart
Tstart
DA7
DA0
D7
D0
TI0 > Th0 * 2
Tend
Tend
Data
(D7 to D0)
Device Address
(DA7 to DA0)
TI0 Th0
Low state (Bit=0)
Acknowledge : Disable (D7 = D0)
Tstart
Tstart
Tack
TI1 > Th1 * 2
A
C
K
TI1 Th1
High state (Bit=1)
DA7
DA0
D7
D0
Tend
Tack
Device Address
(DA7 to DA0)
Data
(D7 to D0)
Acknowledge : Enable (D7 = 1)
Fig6.Bit detection Diagram
D7
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
D6
D5
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
D4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
D3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
D2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
D1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
D0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
FB voltage (mV)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
5
1
2
8
3
11
4
14
5
17
6
20
7
23
8
26
9
29
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
35
38
44
50
56
62
68
74
80
86
92
98
104
116
128
140
152
164
176
188
*200
(*Default)
Table3. Data Register vs. FB Voltage
No.A2184-7/16
LV52204MT
Start up and Shutdown
The device becomes enabled when SWIRE is initially taken high.The dimming mode is determined within Tsel and the
boost converter start up after Tdel. To place the device into shutdown mode, the SWIRE must be held low for Toff.
PWM MODE
V
IN
Tsel
Tdel
Toff
SWIRE
FB
200m * duty
Shutdown delay
FCAP
DCDC_EN
(internal signal)
Digital MODE
V
IN
Tdel
Tsel
Tw1
Toff
SWIRE
Device Address & data
Device Address & data
Programed value
Shutdown delay
Tw0
FB
FCAP
DCDC_EN
(internal signal)
Fig7.Start up and shutdown diagram
No.A2184-8/16
LV52204MT
Open LED Protection
If SW terminal voltage exceeds a threshold Vovp (38V typ) for 8 cycles, boost converter enters shutdown mode. In
order to restart the IC, SWIRE signal is required again.
Over Current Protection
Current limit value for built-in power MOS is around 0.7A. The power MOS is turned off for each switching cycle when
peak current through it exceeds the limit value.
Under Voltage Lock Out (UVLO)
UVLO operation works when V terminal voltage is below 2.2V.
IN
Thermal Shutdown
When chip temperature is too high, boost converter is stopped.
Application Circuit Diagram
10LEDs
D1
L1
22μH
VBAT
C1
1μF
C2
1μF
PWM/
1-Wire
C3
220nF
R1
10Ω
L1: VLS3012T-220M49 (TDK), VLF504015MT-220M (TDK)
D1: MBR0540T1 (ON semi), NSR05F40 (ONsemi)
C2: GRM21BR71H105K (Murata), C1608X5R1H105K (TDK)
No.A2184-9/16
LV52204MT
6LEDs
D1
L1
10μH
VBAT
C1
1μF
C2
1μF
PWM/
1-WIRE
C3
220nF
R1
10Ω
L1: VLS3012T-100M72 (TDK), VLF302512M-100M (TDK)
D1: MBR0540T1 (ON semi), NSR05F40 (ONsemi)
C2: GRM21BR71H105K (Murata), C1608X5R1H105K (TDK)
No.A2184-10/16
LV52204MT
Typical Characteristics (V = 3.6V, L = 22μH, T = 25°C, unless otherwise specified)
IN
Efficiency -- Output current
=3.6V
Efficiency -- Output current
100
90
80
70
60
100
90
80
70
60
V
10LED
IN
10LED
8LED
3.6V
50
40
50
40
0
5
10
15
20
0
5
10
15
20
100
90
LED current -- mA
LED current -- mA
FB voltage -- DATA register
Mode=Digital
FB voltage -- PWM duty
200
150
100
200
150
100
Mode=PWM
50
0
50
0
0
2
4
6
8
10 12 14 16 18 20 22 24 26 28 30 32
0
10
20
30
40
50
60
70
80
90
Data register
PWM duty -- %
FB voltage -- Temperature
FB voltage -- Temperature
200
180
160
200
180
160
Duty=100%
DATA=31
140
120
100
80
140
120
100
80
Duty=50%
Duty=10%
DATA=16
60
60
40
40
DATA=06
20
0
20
0
Mode=Digital
Mode=PWM
--30
--15
0
15
30
45
60
75
90
--30
--15
0
15
30
45
60
75
Temperature -- °C
Temperature -- °C
V
current -- V
LED current -- PWM frequency
IN
IN
1000
20
800
600
400
75%
50%
25%
15
10
5
0
200
0
2
3
4
5
6
0.1
1
10
100
V
IN
-- V
PWM frequency -- kHz
No.A2184-11/16
LV52204MT
PACKAGE DIMENSIONS
WDFN6 2x2, 0.65P
CASE 511BR-01
ISSUE O
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
D
A
B
EXPOSED Cu
MOLD CMPD
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.25 mm FROM THE TERMINAL TIP.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
DETAIL B
ALTERNATE
CONSTRUCTIONS
PIN ONE
REFERENCE
MILLIMETERS
E
DIM MIN
MAX
0.80
0.05
A
A1
A3
b
0.70
0.00
0.20 REF
0.10 C
L
L
0.25
0.35
D
D2
E
E2
e
2.00 BSC
0.10 C
L1
1.50
0.90
1.70
2.00 BSC
TOP VIEW
DETAIL A
1.10
ALTERNATE
0.65 BSC
A3
DETAIL B
CONSTRUCTIONS
L
L1
0.20
---
0.40
0.15
0.05 C
A
GENERIC
MARKING DIAGRAM*
0.05 C
6X
A1
SEATING
PLANE
NOTE 4
C
SIDE VIEW
D2
1
XX M
XX = Specific Device Code
DETAIL A
L
1
3
M
= Date Code
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, G or microdot
,
E2
may or may not be present.
RECOMMENDED
MOUNTING FOOTPRINT
6
4
6X
b
M
0.10
0.05
C A B
e
6X
1.72
M
NOTE 3
0.45
C
BOTTOM VIEW
1.12
2.30
PACKAGE
OUTLINE
1
0.65
PITCH
6X
0.40
DIMENSIONS: MILLIMETERS
LV52204MT is as follows.
MARKING DIAGRAM
W4M
W4 = Device Code
M
= Date Code
= Pb-Free Package
PS No.A2184-12/16
LV52204MT
PS No.A2184-13/16
LV52204MT
PS No.A2184-14/16
LV52204MT
PS No.A2184-15/16
LV52204MT
ORDERING INFORMATION
Device
Package
Shipping (Qty / Packing)
3000 / Tape & Reel
WDFN6 (2x2)
(Pb-Free)
LV52204MTTBG
ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at
www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no
warranty, representation or guarantee regarding the suitabilityof its products for any particular purpose, nor does SCILLC assume any liability arising out of the
application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical
experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use
as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in
which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for
any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or
death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the
part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PS No.A2184-16/16
相关型号:
©2020 ICPDF网 联系我们和版权申明