NCD5707BDR2G [ONSEMI]
IGBT Gate Drivers, High-Current, Stand-Alone, Non-inverting;型号: | NCD5707BDR2G |
厂家: | ONSEMI |
描述: | IGBT Gate Drivers, High-Current, Stand-Alone, Non-inverting 栅 双极性晶体管 |
文件: | 总21页 (文件大小:435K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DATA SHEET
www.onsemi.com
MARKING
DIAGRAM
High Current IGBT/MOSFET
Gate Drivers
8
8
1
NCx5707y
ALYW
NCD5707A, NCV5707A,
NCD5707B, NCV5707B,
NCD5707C, NCV5707C
SOIC−8
D SUFFIX
CASE 751
G
1
The NCx5707y are high−current, high−performance stand−alone
IGBT drivers for high power applications that include solar inverters,
motor control and uninterruptible power supplies. The devices offer a
cost−effective solution by eliminating external output buffer. Devices
protection features include accurate Under−voltage−lockout (UVLO),
desaturation protection (DESAT) and Active open−drain FAULT
output. The drivers also feature an accurate 5.0 V output. The drivers
are designed to accommodate a wide voltage range of bias supplies.
NCx5707B accommodates bipolar voltages.
NCx5707y = Specific Device Code
x
= D or V
y
= A, B or C
A
L
= Assembly Location
= Wafer Lot
Y
W
G
= Year
= Work Week
= Pb−Free Package
Depending on the pin configuration the devices also include Active
PIN CONNECTIONS
Miller Clamp (NCx5707A) and separate high and low (V and V
)
OL
OH
1
2
3
4
8
7
6
5
VIN
VREF
FLT
CLAMP
GND
VO
driver outputs for system design convenience (NCx5707C).
All three available pin configuration variants have 8−pin SOIC
package.
DESAT
VCC
Features
NCx5707A
NCx5707B
• High Current Output (+4/−6 A) at IGBT/MOSFET Miller Plateau
voltages
• Low Output Impedance for Enhanced IGBT/MOSFET Driving
• Short Propagation Delay with Accurate Matching
• Direct Interface to Digital Isolator/Opto−coupler/Pulse Transformer
for Isolated Drive, Logic Compatibility for Non−isolated Drive
• Designed for AEC−Q100 Certification (NCV5707y)
1
2
3
4
8
7
6
5
VIN
VREF
FLT
VEE
GND
VO
DESAT
VCC
1
2
3
4
8
7
6
5
• DESAT Protection with Programmable Delay
• Soft Turn Off during IGBT Short Circuit
• Tight UVLO Thresholds for Bias Flexibility
• Wide Bias Voltage Range
VIN
VREF
FLT
GND
VOL
VOH
VCC
DESAT
• This Device is Pb−Free, Halogen−Free and RoHS Compliant
NCx5707C
x = D or V
NCx5707A Features
• Active Miller Clamp to Prevent Spurious Gate Turn−on
ORDERING INFORMATION
See detailed ordering and shipping information on page 9 of
this data sheet.
NCx5707B Features
• Negative Output Voltage for Enhanced IGBT/MOSFET Driving
NCx5707C Features
• Separate Outputs for V and V
OL
OH
Typical Applications
• Motor Control
• Uninterruptible Power Supplies (UPS)
• Automotive Power Supplies
• HEV/EV PTC Heaters
© Semiconductor Components Industries, LLC, 2021
1
Publication Order Number:
December, 2021 − Rev. 0
NCV5707/D
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
NCx5707A
VREF
DESAT
VCC
VCC
VO
CLAMP
GND
VIN
FLT
VEE
VEE
NCx5707B
VREF
DESAT
VCC
VCC
VO
VIN
FLT
GND
VEE
VEE
NCx5707C
VREF
DESAT
VCC
VCC
VOH
VOL
VIN
FLT
GND
VEE
Figure 1. Simplified Application Schematics
www.onsemi.com
2
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
FLT
TSD
SET
Q
S
CLR
Q
R
IDESAT‐CHG
DELAY
DESAT
+
‐
SET
CLR
VDESAT‐THR
S
Q
Q
VCC
R
VREF
VO
VIN
RIN‐L
Bandgap
VREF
VCC
STO
VUVLO
‐
‐
CLAMP
+
+
VMC‐THR
Q
SET
CLR
S
R
Q
Figure 2(a). Detailed Block Diagram NCx5707A
GND
CLAMP
VIN
CLAMP
GND
VCC
VREF
FLT
LDO
STO
VCC
UVLO
VO
LATCH
VCC
TSD
DESAT
DESAT
Figure 2(b). Simplified Block Diagram NCx5707A
www.onsemi.com
3
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
FLT
TSD
SET
Q
S
CLR
Q
R
IDESAT‐CHG
DELAY
DESAT
+
‐
SET
CLR
VDESAT‐THR
S
Q
Q
VCC
R
VREF
VO
VIN
RIN‐L
Bandgap
VREF
VCC
VEE
STO
VUVLO
‐
+
VEE
VEE
Figure 3(a). Detailed Block Diagram NCx5707B
GND
VIN
VEE
VCC
VREF
FLT
LDO
STO
VCC
UVLO
VO
LATCH
VCC
GND
TSD
DESAT
DESAT
Figure 3(b). Simplified Block Diagram NCx5707B
www.onsemi.com
4
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
FLT
TSD
SET
Q
S
CLR
Q
R
IDESAT‐CHG
DELAY
DESAT
+
‐
SET
CLR
VDESAT‐THR
S
Q
Q
VCC
R
VREF
VOH
VOL
VIN
RIN‐L
Bandgap
VREF
VCC
STO
VUVLO
‐
+
Figure 4(a). Detailed Block Diagram NCx5707C
GND
VIN
GND
VCC
VREF
FLT
LDO
STO
VOL
VCC
UVLO
VOH
LATCH
VCC
TSD
DESAT
DESAT
Figure 4(b). Simplified Block Diagram NCx5707C
www.onsemi.com
5
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
Table 1. PIN FUNCTION DESCRIPTION
Pin Name
No.
I/O/x
Description
VIN
1
I
Input signal to control the output. In applications which require galvanic isolation, VIN is generat-
ed at the opto output, the pulse transformer secondary or the digital isolator output. VO (VOH/
VOL) signal is in phase with VIN. VIN is internally clamped to GND and has a pull−down resistor
of 1 MW to ensure that an output is low in the absence of an input signal. A minimum pulse−
width is required at VIN before VO (VOH/VOL) is activated.
VREF
FLT
2
3
O
O
5 V reference generated within the driver is brought out to this pin for external bypassing and for
powering low bias circuits (such as digital isolators).
Fault open drain output (active low) that allows communication to the main controller that the
driver has encountered a fault condition and has deactivated the output. Open drain allows easy
setting of (inactive) high level and parallel connection of multiple fault signals.
Connect to 10k pull−up resistor recommended. Truth Table is provided in the datasheet to indi-
cate conditions under which this signal is asserted. Capable of driving optos or digital isolators
when isolation is required.
DESAT
VCC
4
5
6
I
Input for detecting the desaturation of IGBT/MOSFET due to a fault condition. A capacitor con-
nected to this pin allows a programmable blanking delay every ON cycle before DESAT fault is
processed, thus preventing false triggering.
x
Positive bias supply for the driver. The operating range for this pin is from UVLO to the maxi-
mum voltage. A good quality bypassing capacitor is required from this pin to GND and should be
placed close to the pins for best results.
VO
(NCx5707A,
NCx5707B)
O
Driver output that provides the appropriate drive voltage, source and sink current to the IGBT
gate. VO is actively pulled low during start−up and under Fault conditions.
VOH
6
7
7
O
O
x
Driver high output that provides the appropriate drive voltage and source current to the IGBT
gate.
(NCx5707C)
VOL
(NCx5707C)
Driver low output that provides the appropriate drive voltage and sink current to the IGBT gate.
VOL is actively pulled low during start−up and under Fault conditions.
GND
(NCx5707A,
NCx5707B)
This pin should connect to the IGBT Emitter or MOSFET source with a short trace. All power pin
bypass capacitors should be referenced to this pin and kept at a short distance from the pin.
GND
8
8
x
x
This pin should connect to the IGBT Emitter or MOSFET source with a short trace. All power pin
bypass capacitors should be referenced to this pin and kept at a short distance from the pin.
(NCx5707C)
VEE
(NCx5707B)
A negative voltage with respect to GND can be applied to this pin and that will allow VO to go to
a negative voltage during OFF state. A good quality bypassing capacitor is needed from VEE to
GND. If a negative voltage is not applied or available, this pin must be connected to GND.
CLAMP
(NCx5707A)
8
I/O
Provides clamping for the IGBT/MOSFET gate during the off period to protect it from parasitic
turn−on. To be tied directly to IGBT gate with minimum trace length for best results.
www.onsemi.com
6
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
Table 2. ABSOLUTE MAXIMUM RATINGS (Note 1)
Parameter
Differential Power Supply
Symbol
−V (V )
max
Minimum
Maximum
Unit
V
V
0
36
22
CC
EE
Positive Power Supply
Negative Power Supply
Gate Output High
Gate Output Low
Input Voltage
V
−GND
−GND
−0.3
−18
V
CC
V
0.3
V
EE
(V , V )−GND
V
V
+ 0.3
V
O
OH
CC
(V , V )−GND
V − 0.3
EE
V
O
OL
V
IN
−GND
−0.3
−0.3
5.5
V
DESAT Voltage
V
−GND
DESAT
+ 0.3
V
CC
FLT current
Sink
mA
I
20
FLT−SINK
Power Dissipation
SO−8 package
PD
700
mW
Maximum Junction Temperature
T
150
°C
°C
kV
kV
−
J(max)
Storage Temperature Range
TSTG
−65 to 150
ESD Capability, Human Body Model (Note 2)
ESD Capability, Charged Device Model (Note 2)
Moisture Sensitivity Level
ESD
4
2
HBM
CDM
ESD
MSL
1
Lead Temperature Soldering
Reflow (SMD Styles Only), Pb−Free Versions (Note 3)
T
SLD
260
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
2. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per AEC−Q100−002 (EIA/JESD22−A114)
ESD Charged Device Model tested per AEC−Q100−011 (EIA/JESD22−C101).
Latchup Current Maximum Rating: ≤100 mA per JEDEC standard: JESD78, 25°C
3. For information, please refer to our Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
Table 3. THERMAL CHARACTERISTICS
Parameter
Symbol
Value
Unit
Thermal Characteristics, SOIC−8 (Note 4)
Thermal Resistance, Junction−to−Air (Note 5)
°C/W
R
176
q
JA
4. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
2
2
5. Values based on copper area of 100 mm (or 0.16 in ) of 1 oz copper thickness and FR4 PCB substrate.
Table 4. OPERATING RANGES (Note 6)
Parameter
Differential Power Supply
Symbol
−V (V )
max
Min
Max
30
20
0
Unit
V
V
CC
EE
Positive Power Supply
Negative Power Supply
Input Voltage
V
CC
UVLO
−15
0
V
V
EE
V
V
IN
5
V
Input pulse width
t
40
ns
°C
on
Ambient Temperature
T
−40
125
A
6. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
www.onsemi.com
7
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
Table 5. ELECTRICAL CHARACTERISTICS V = 15 V, V = 0 V, Kelvin GND connected to V . For typical values T = 25°C,
CC
EE
EE
A
for min/max values, T is the operating ambient temperature range that applies, unless otherwise noted.
A
Parameter
Test Conditions
Symbol
Min
Typ
Max
Unit
LOGIC INPUT and OUTPUT
Input Threshold Voltages
Pulse−Width = 150 ns, V = 5 V
V
EN
High−state (Logic 1) Required Voltage applied to get output to go high
Low−state (Logic 0) Required Voltage applied to get output to go low
V
V
4.3
1.2
IN−H1
0.75
3.7
IN−L1
No state change
Voltage applied without change in output state
V
IN−NC
Input Current
High−state
Low−state
mA
V
V
= 4.5 V
= 0.5 V
I
I
10
1
IN−H
IN−H
IN−L
IN−L
Input Pulse−Width
No Response at the Output
Voltage thresholds consistent with input
specs
ns
t
10
on−min1
Guaranteed Response at the
Output
t
30
on−min2
FLT Threshold Voltage
Low State
V
(I
= 15 mA)
V
FLT−L
0.5
1.0
FLT−SINK
High State
External pull−up
V
FLT−H
V
CC
+0.3
DRIVE OUTPUT
Output Low State
V
V
I
I
I
= 200 mA, T = 25°C
V
V
V
0.1
0.2
0.8
0.2
0.5
1.2
sink
sink
sink
A
OL1
OL2
OL3
= 200 mA, T = −40°C to 125°C
A
= 1.0 A, T = 25°C
A
Output High State
I
src
I
src
I
src
= 200 mA, T = 25°C
V
OH1
V
OH2
V
OH3
14.5
14.2
13.8
14.8
14.7
14.1
A
= 200 mA, T = −40°C to 125°C
A
= 1.0 A, T = 25°C
A
Peak Driver Current, Sink
(Note 7)
R
= 0.1 W, V = 15 V, V = −8 V
= 9 V (near Miller Plateau)
I
I
6.8
6.1
A
A
W
G
CC
EE
PK−snk1
V
O
PK−snk2
Peak Driver Current, Source
(Note 7)
R
= 0.1 W, V = 15 V, V = −8 V
I
7.8
4.0
G
CC
EE
PK−src1
I
PK−src2
V
O
= 9 V (near Miller Plateau)
Soft Turn−Off resistance
V
IN
= 5 V, V = 5.3 V
R
DS_on−STO
30
O
DYNAMIC CHARACTERISTICS
Turn−on Delay
Negative input pulse width = 10 ms
Positive input pulse width = 10 ms
For input or output pulse width > 150 ns,
t
t
45
40
56
60
75
90
ns
ns
ns
pd−on
(see timing diagram)
Turn−off Delay
(see timing diagram)
pd−off
Propagation Delay Distortion
(=t
− t
)
T = 25°C
T = −40°C to 125°C
A
t
−15
−25
−7
−5
25
pd−on pd−off
A
distort1
t
distort2
Propagation Delay Distortion
between Parts (Note 7)
t
−30
0
30
ns
ns
ns
ms
ns
distort −tot
Rise Time (Note 7)
(see timing diagram)
C
C
= 1.0 nF
= 1.0 nF
t
9.2
7.9
12
load
load
rise
Fall Time (Note 7)
(see timing diagram)
t
fall
Delay from FLT under UVLO/
TSD to VO/VOL
t
t
9
16
d1−OUT
d2−OUT
Delay from DESAT to VO/VOL
(Note 7)
220
7. Values based on design and/or characterization.
www.onsemi.com
8
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
Table 5. ELECTRICAL CHARACTERISTICS V = 15 V, V = 0 V, Kelvin GND connected to V . For typical values T = 25°C,
CC
EE
EE
A
for min/max values, T is the operating ambient temperature range that applies, unless otherwise noted.
A
Parameter
Test Conditions
Symbol
Min
Typ
Max
Unit
DYNAMIC CHARACTERISTICS
Delay from UVLO/TSD to FLT
(Note 7)
t
7.3
ms
d3−FLT
MILLER CLAMP (NCX5707A ONLY)
Clamp Voltage
I
I
= 500 mA, T = 25°C
V
clamp
1.2
2.0
1.4
2.2
V
V
sink
A
= 500 mA, T = −40°C to 125°C
sink
A
Clamp Activation Threshold
DESAT PROTECTION
V
1.8
5.7
2.2
MC−THR
DESAT Threshold Voltage
V
6.0
160
0.24
30
6.3
V
DESAT−THR
DESAT Threshold Filtering Time (see Figure 5)
Blanking Charge Current
Blanking Discharge Current
UVLO
t
ns
FILTER
DESAT−CHG
I
0.20
0.28
mA
mA
I
DESAT−DIS
UVLO Startup Voltage
UVLO Disable Voltage
UVLO Hysteresis
V
7.7
6.7
8.0
7.0
1.0
8.3
7.3
V
V
V
UVLO−OUT−ON
V
UVLO−OUT−OFF
V
UVLO−HYST
VREF
Voltage Reference
I
= 10 mA
V
4.85
100
5.00
5.15
20
V
REF
REF
Reference Output Current
(Note 7)
I
mA
REF
Recommended Capacitance
C
nF
VREF
SUPPLY CURRENT
Current Drawn from V
V
= 15 V
I
0.9
1.5
mA
mA
CC
CC
CC−SB
Standby (No load on output, FLT, VREF)
Current Drawn from V
(NCx5707B ONLY)
V
EE
= −10 V
I
−0.41
−0.32
EE
EE−SB
Standby (No load on output, FLT, VREF)
THERMAL SHUTDOWN
Thermal Shutdown Temperature
(Note 7)
T
T
188
33
°C
°C
SD
Thermal Shutdown Hysteresis
(Note 7)
SH
7. Values based on design and/or characterization.
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
ORDERING INFORMATION
†
Device
Package
Shipping
NCD5707ADR2G (in development)
NCD5707BDR2G (in development)
NCD5707CDR2G (in development)
NCV5707ADR2G (in development)
NCV5707BDR2G
SOIC−8
(Pb−Free)
2500 / Tape & Reel
NCV5707CDR2G (in development)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
9
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
TYPICAL CHARACTERISTICS
80
70
60
13.5
13.0
t
PD−ON
12.5
12.0
t
PD−OFF
50
40
11.5
11.0
−40 −20
0
20
40
60
80
100 120
−40 −20
0
20
40
60
80
100 120
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 5. Propagation Delay vs. Temperature
Figure 6. Fault to Output Low Delay
20
15
10
5
8
7
6
5
4
3
2
t
fall
t
rise
1
0
0
−5
0
5
10
15
−40 −20
0
20
40
60
80
100 120
V
O
(V, V = 15 V, V = −8 V)
TEMPERATURE (°C)
CC
EE
Figure 7. Output Rise/Fall Time
Figure 8. Output Source Current vs. Output
Voltage
5.05
5.04
5.03
5.02
5.01
5.00
4.99
4.98
4.97
8
7
6
5
4
3
2
1
0
4.96
4.95
−5
0
5
10
15
0
2
4
6
8
10
V
O
(V, V = 15 V, V = −8 V)
I
(mA)
CC
EE
REF
Figure 9. Output Sink Current vs. Output
Voltage
Figure 10. VREF Voltage vs. Current
www.onsemi.com
10
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
TYPICAL CHARACTERISTICS
5.05
5.04
5.03
5.02
5.01
5.00
4.99
4.98
4.97
250
248
246
244
V
@ I
= 0 mA
REF
REF
V
REF
@ I
= 10 mA
REF
242
240
4.96
4.95
−40 −20
0
20
40
60
80
100 120
−40 −20
0
20
40
60
80
100 120
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 11. VREF Voltage vs. Temperature
Figure 12. DESAT Charge Current vs.
Temperature
6.3
6.2
6.1
6.0
9.0
8.5
8.0
7.5
7.0
V
UVLO−OUT−ON
V
UVLO−OUT−OFF
5.9
5.8
6.5
6.0
−40 −20
0
20
40
60
80
100 120
−40 −20
0
20
40
60
80
100 120
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 13. DESAT Threshold Voltage vs.
Temperature
Figure 14. UVLO Threshold Voltages
4.5
4.0
3.5
3.0
2.5
2.0
1.5
0.8
0.7
0.6
0.5
V
IN−H
0.4
0.3
V
IN−L
1.0
0.5
−40 −20
0
20
40
60
80
100 120
−40 −20
0
20
40
60
80
100 120
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 15. VO vs. VIN at 255C
Figure 16. Fault Output, Sinking 15 mA
(VCC = 15 V, VEE = 0 V)
www.onsemi.com
11
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
TYPICAL CHARACTERISTICS
30
Frequency
1.8
1.3
(V = 15 V,
CC
25
20
15
10
V
EE
= 0 V, 25°C)
C
= 100 nF
C
= 10 nF
C = 1 nF
G
G
G
0.8
0.3
5
0
−40 −20
0
20
40
60
80
100 120
1
10
100
1000
TEMPERATURE (°C)
FREQUENCY (kHz)
Figure 17. VCLAMP at 0.5 A (NCx5707A Only)
Figure 18. Supply Current vs. Switching
Frequency (VCC = 15 V, VEE = 0 V, 255C)
2.10
1400
1200
1000
800
V
OH3
V
OL3
2.05
2.00
600
400
V
OH2
200
0
V
OL2
−40 −20
0
20
40
60
80
100 120
−40 −20
0
20
40
60
80
100 120
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 19. Output Low/High State Voltage
Figure 20. Clamp Activation Threshold Voltage
45
40
35
35
34
33
32
NEGATIVE t
POSITIVE t
ON−MIN2
31
30
29
28
27
ON−MIN2
30
25
26
25
−40 −20
0
20
40
60
80
100 120
−40 −20
0
20
40
60
80
100 120
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 21. Minimum Input Pulse Width For
Guaranteed Response at the Output
Figure 22. Soft Turn Off Resistance
www.onsemi.com
12
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
Applications and Operating Information
This section lists the details about key features and
operating guidelines for the NCx5707y.
High Drive Current Capability
The NCx5707y driver family is equipped with many
features which facilitate
a
superior performance
IGBT/MOSFET driving circuit. Foremost amongst these
features is the high drive current capability. The drive
current of an IGBT/MOSFET driver is a function of the
differential voltage on the output pin (V −VOH/VO for
CC
source current, VOL/VO−V for sink current) as shown in
EE
Figure 23. Figure 23 also indicates that for a given
VOH/VOL value, the drive current can be increased by
using higher V /V power supply). The drive current
Figure 23. Output Current vs. Output Voltage Drop
CC EE
tends to drop off as the output voltage goes up (for turn−on
event) or goes down (for turn−off event). As explained in
many IGBT/MOSFET application notes, the most critical
phase of IGBT switching event is the Miller plateau region
where the gate voltage remains constant at a voltage
(typically in 9−11 V range depending on IGBT/MOSFET
design and the collector current), but the gate drive current
When driving larger IGBTs/MOSFETs for higher current
applications, the drive current requirement is higher, hence
lower R is used. Larger IGBTs/MOSFETs typically have
G
high input capacitance. On the other hand, if the NCx5707y
is used to drive smaller IGBT/MOSFET (lower input
capacitance), the drive current requirement is lower and a
is used to charge/discharge the Miller capacitance (C ). By
higher R is used. Thus, for most typical applications, the
GC
G
providing a high drive current in this region, a gate driver can
significantly reduce the duration of the phase and help
reducing the switching losses. The NCx5707y addresses this
requirement by providing and specifying a high drive
current in the Miller plateau region. Most other gate driver
ICs merely specify peak current at the start of switching –
which may be a high number, but not very relevant to the
application requirement. It must be remembered that other
considerations such as EMI, diode reverse recovery
performance, etc., may lead to a system level decision to
trade off the faster switching speed against low EMI and
reverse recovery. However, the use of NCx5707y does not
preclude this trade−off as the user can always tune the drive
current by employing external series gate resistor. Important
thing to remember is that by providing a high internal drive
current capability, the NCx5707y facilitates a wide range of
gate resistors. Another value of the high current at the Miller
plateau is that the initial switching transition phase is shorter
and more controlled. Finally, the high gate driver current
(which is facilitated by low impedance internal FETs),
ensures that even at high switching frequencies, the power
dissipation from the drive circuit is primarily in the external
series resistor and more easily manageable. Experimental
results have shown that the high current drive results in
driver load RC time constant remains fairly constant.
Caution must be exercised when using the NCx5707y with
a very low load RC time constant. Such a load may trigger
internal protection circuitry within the driver and disable the
device. Figure 24 shows the recommended minimum gate
resistance as a function of IGBT/MOSFET gate capacitance
and gate drive trace inductance.
Figure 24. Recommended Minimum Gate Resistance
as a Function of IGBT/MOSFET Gate Capacitance
reduced turn−on energy (E ) for the IGBT/MOSFET
ON
switching.
www.onsemi.com
13
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
Gate Voltage Range
case the controller fails to do so, the driver output shutdown
ensures IGBT/MOSFET protection after t
The negative drive voltage for gate (with respect to GND,
Emitter or Source of the IGBT/MOSFET) is a robust way to
ensure that the gate voltage does not rise above the threshold
voltage due to the Miller effect. In systems where the
negative power supply is available, the VEE option offered
by NCx5707B allows not only a robust operation, but also
a higher drive current for turn−off transition. Adequate
bypassing between VEE pin and GND pin is essential if this
option is used.
.
d1−OUT
The V range for the NCx5707y is quite wide and allows
CC
the user the flexibility to optimize the performance or use
available power supplies for convenience.
Under Voltage Lock Out (UVLO)
This feature ensures reliable switching of the
IGBT/MOSFET connected to the driver output. At the start
of the driver’s operation when V is applied to the driver,
CC
the output remains turned−off. This is regardless of the
signals on V until the V reaches the UVLO Output
IN
CC
Enabled (V
) level. After the V rises above
UVLO−OUT−ON
CC
the V
level, the driver is in normal operation.
UVLO−OUT−ON
The state of the output is controlled by signal at V .
IN
If the V
falls below the UVLO Output Disabled
CC
(V ) level during the normal operation of the
UVLO−OUT−OFF
driver, the Fault output is activated and the output is shut−down
(after a delay) and remains in this state. The driver output
Figure 25. UVLO Function and Limits
does not start to react to the input signal on V until the V
IN
CC
Timing Delays and Impact on System Performance
The gate driver is ideally required to transmit the input
signal pulse to its output without any delay or distortion. In
the context of a high−power system where IGBTs/MOSFETs
are typically used, relatively low switching frequency (in
tens of kHz) means that the delay through the driver itself
may not be as significant, but the matching of the delay
between different drivers in the same system as well as
between different edges has significant importance. With
reference to Figure 26(a), two input waveforms are shown.
They are typical complementary inputs for high−side (HS)
and low−side (LS) of a half−bridge switching configuration.
The dead−time between the two inputs ensures safe
transition between the two switches. However, once these
inputs are through the driver, there is potential for the actual
gate voltages for HS and LS to be quite different from the
intended input waveforms as shown in Figure 26(a). The end
result could be a loss of the intended dead−time and/or
pulse−width distortion. The pulse−width distortion can
create an imbalance that needs to be corrected, while the loss
of dead−time can eventually lead to cross−conduction of the
switches and additional power losses or damage to the
system.
rises above the V
again. The waveform
UVLO−OUT−ON
showing the UVLO behavior of the driver is in Figure 25.
In an IGBT drive circuit, the drive voltage level is
important for drive circuit optimization. If V
UVLO−OUT−OFF
is too low, it will lead to IGBT/MOSFET being driven with
insufficient gate voltage. A quick review of IGBT/MOSFET
characteristics can reveal that driving IGBT/MOSFET with
low voltage (in 10−12 V IGBT, 6−7 V MOSFET range) can
lead to a significant increase in conduction loss. So, it is
prudent to guarantee V
at a reasonable level
UVLO−OUT−OFF
(above 9/12 V), so that the IGBT/MOSFET is not forced to
operate at a non−optimum gate voltage. On the other hand,
having a very high drive voltage ends up increasing
switching losses without much corresponding reduction in
conduction loss. So, the V
value should not
UVLO−OUT−ON
be too high (generally, well below 15 V). These conditions
lead to a tight band for UVLO enable and disable voltages,
while guaranteeing a minimum hysteresis between the two
values to prevent hiccup mode operation. The NCx5707y
meets these tight requirements and ensures smooth
IGBT/MOSFET operation.
A UVLO event (V voltage going below V
)
.
CC
UVLO−OUT−OFF
also triggers activation of FLT output after a delay of t
d3−FLT
The NCx5707y driver is designed to address these timing
challenges by providing a very low pulse−width distortion
and excellent delay matching. As an example, the delay
This indicates to the controller that the driver has
encountered an issue and corrective action needs to be taken.
However, a nominal delay t
= 12 ms is introduced
d1−OUT
matching is guaranteed to t
= 25 ns while many
DISTORT2
between the initiation of the FLT output and actual turning
off of the output. This delay provides adequate time for the
controller to initiate a more orderly/sequenced shutdown. In
of competing driver solutions can be >250 ns.
www.onsemi.com
14
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
Figure 26(a). Timing Waveforms (Other Drivers)
Figure 26(b). NCx5707y Timing Waveforms
Active Miller Clamp Protection
voltage, but this requires second DC source for the negative
gate voltage.
An alternative way is to provide an additional path from
gate to GND with very low impedance. This is exactly what
Active Miller Clamp protection does. Additional trace from
the gate of the IGBT/MOSFET to the Clamp pin of the gate
This feature (offered by NCx5707A) is a cost savvy
alternative to a negative gate voltage. The main requirement
is to hold the gate of the turned−off (for example low−side)
IGBT/MOSFET below the threshold voltage during the
turn−on of the opposite−side (in this example high−side)
IGBT/MOSFET in the half bridge. The turn−on of the
high−side IGBT/MOSFET causes high dv/dt transition on the
collector/drain of the turned−off low−side IGBT/MOSFET.
This high dv/dt then induces current (Miller current) through
driver is introduced. After the V output has gone below the
O
Active Miler Clamp threshold V
the Clamp pin is
MC−THR
shorted to GND and thus prevents the voltage on the gate of
the IGBT to rise above the threshold voltage as shown in
Figure 28. The Clamp pin is disconnected from GND as
soon as the signal to turn on the IGBT/MOSFET arrives to
the gate driver input. The fact that the Clamp pin is engaged
the C
capacitance (Miller capacitance) to the gate
GC
capacitance of the low−side IGBT/MOSFET as shown in
Figure 27. If the path from gate to GND has critical
impedance (caused by R ) the Miller current could rise the
only after the gate voltage drops below the V
G
MC−THR
gate voltage above the threshold level. As a consequence the
low−side IGBT/MOSFET could be turned on for a few tens
or hundreds of nanoseconds. This causes higher switching
losses. One way to avoid this situation is to use negative gate
threshold ensures that the function of this pin does not
interfere with the normal turn−off switching performance
that is user controllable by choice of R .
G
www.onsemi.com
15
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
NCx5707A
NCx5707A
VO
VO
Figure 27. Current Path without Miller Clamp Protection
Figure 28. Current Path with Miller Clamp Protection
Desaturation Protection (DESAT)
IGBT/MOSFET collector−emitter / drain−source voltage
This feature monitors the collector−emitter voltage of the
IGBT in the turned−on state. When the IGBT/MOSFET is
fully turned on, it operates in a saturation region. Its
collector−emitter voltage (called saturation voltage) is
usually low, well below 3 V for most modern
IGBTs/MOSFETs. It could indicate an overcurrent or
similar stress event on the IGBT/MOSFET if the
collector−emitter / drain−source voltage rises above the
saturation voltage, after the IGBT/MOSFET is fully turned
on. Therefore the DESAT protection circuit compares the
collector−emitter drain−source voltage with a voltage level
falls below the saturation level. Blanking time is set by the
value of the capacitor C
.
BLANK
The exact principle of operation of DESAT protection is
described with reference to Figure 29.
At the turned−off output state of the driver, the DESAT pin
is shorted to ground via the discharging transistor (Q ).
DIS
Therefore, the inverting input holds the comparator output
at low level.
At the turned−on output state of the driver, the current
I
from current source starts to flow to the
DESAT−CHG
blanking capacitor C , connected to DESAT pin.
BLANK
V
to check if the IGBT/MOSFET didn’t leave
Appropriate value of this capacitor has to be selected to
ensure that the DESAT pin voltage does not rise above the
DESAT−THR
the saturation region. It will activate FLT output and shut
down driver output (thus turn−off the IGBT/MOSFET), if
threshold level V
before the IGBT fully turns on.
DESAT−THR
the saturation voltage rises above the V . This
DESAT−THR
The blanking time is given by following expression.
According to this expression, a 47 pF C will provide
protection works on every turn−on phase of the
IGBT/MOSFET switching period.
BLANK
a blanking time of (47p *6.5/0.25m =) 1.22 ms.
VDESAT−THR
IDESAT−CHG
Soft Turn Off (STO)
t
BLANK + CBLANK @
To prevent the voltage overshoot damage caused by
turning−off the IGBT/MOSFET, the NCx5707y drivers are
equipped by Soft Turn Off (STO) function. This function is
activated when the DESAT protection is activated and
reduce the turn off voltage overshoot by added internal turn
off resistance (RDS_ON−STO) see Table 5 and Figure 30.
At the beginning of turning−on of the IGBT/MOSFET,
the collector−emitter / drain−source voltage is much higher
than the saturation voltage level which is present after the
IGBT/MOSFET is fully turned on. It takes almost 1 ms
between the start of the IGBT/MOSFET turn−on and the
moment when the collector−emitter / drain−source voltage
falls to the saturation level. Therefore the comparison is
delayed by a configurable time period (blanking time) to
prevent false triggering of DESAT protection before the
After the IGBT/MOSFET is fully turned−on, the
flows through the DESAT pin to the series
I
DESAT−CHG
resistor R
and through the high voltage diode and
S−DESAT
then through the collector/drain and IGBT/MOSFET to the
emitter/source. Care must be taken to select the resistor
R
value so that the sum of the saturation voltage,
S−DESAT
drop on the HV diode and drop on the R
caused by
S−DESAT
current I
flowing from DESAT source current is
DESAT−CHG
smaller than the DESAT threshold voltage. Following
expression can be used:
V
DESAT−THR u
R
S−DESAT @ IDESAT−CHG ) VF_HV diode ) VCESAT_IGBT
www.onsemi.com
16
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
Important part for DESAT protection to work properly is
the high voltage diode. It must be rated for at least same
voltage as the low side IGBT/MOSFET. The safety margin
is application dependent.
The typical waveforms for IGBT/MOSFET overcurrent
condition are outlined in Figure 30.
VDC-LINK
VREF
HS-MOSFET
V
CC
I
DESAT-CHG
Control
Logic
HV diode
V
DESAT
R
+
-
S
DESAT
R
S-DESAT
I
D-LS
FLT
C
BLANK
V
I
DESAT-THR
DESAT-DIS
Vo
V
DS-SAT
LS-MOSFET
R
G
Q
DIS
GND
GND
GND
GND
Figure 29. Desaturation Protection Schematic
www.onsemi.com
17
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
* VIN falling edge has no effect on VO STO
*
VIN
[V]
0
t[s]
VO
[V]
STO
0
t[s]
t[s]
VFLT
[V]
tIGBT‐ON
0
HV‐V DC‐LINK
VCE‐SAT2
VCE‐LS
[V]
VCE‐SAT1
0
t[s]
t[s]
t[s]
IC‐MAX
IC‐LS
[A]
0
VDESAT
[V]
VDESAT‐THR
0
tFILTER
tBLANK
Figure 30. Desaturation Protection Waveforms
www.onsemi.com
18
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
Input Signal
The input signal controls the gate driver output. Figure 31
applications where the input is coming through an
shows the typical connection diagrams for isolated
opto−coupler or a pulse transformer.
DRIVER
VREF
DRIVER
VREF
R
S
R
C
D
D
VIN
VIN
R
P
D
ZENER
C
D
R
D
GND
GND
Figure 31. Opto−coupler or Pulse Transformer At Input
The relationship between gate driver input signal from a
pulse transformer (Figure 32) or opto−coupler (Figure 33)
and the output is defined by many time and voltage values.
The time values include output turn−on and turn−off delays
delay times are defined from 50% of input transition to first
10% of the output transition to eliminate the load
dependency. The input voltage parameters include input
high (V
) and low (V
) thresholds as well as the
IN−H1
IN−L1
(t
and t
), output rise and fall times (t and t )
input range for which no output change is initiated
(V ).
pd−on
pd−off
rise
fall
and minimum input pulse−width (t
). Note that the
on−min
IN−NC
V
IN-H1
V
IN-NC
V
IN
V
IN-L1
t
pd-on
t
fall
t
on-min
t
t
rise
pd-on
90%
10%
V
OUT
Figure 32. Input and Output Signal Parameters for Pulse Transformer
www.onsemi.com
19
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
V
IN-H1
V
IN-NC
V
IN
V
IN-L1
t
t
t
fall
on-min
pd-on
t
t
rise
pd-on
V
OUT
90%
10%
Figure 33. Input and Output Signal Parameters for Opto−coupler
Use of VREF Pin
The NCx5707y provides an additional 5.0 V output
(VREF) that can serve multiple functions. This output is
capable of sourcing up to 10 mA current for functions such
as opto−coupler interface or external comparator interface.
The VREF pin should be bypassed with at least a 100 nF
capacitor (higher the better) irrespective of whether it is
being utilized for external functionality or not. VREF is
highly stable over temperature and line/load variations (see
characteristics curves for details)
Fault Output Pin
This pin provides the feedback to the controller about the
driver operation. The situations in which the FLT signal
becomes active (low value) are summarized in the Table 6.
Table 6. FLT LOGIC TRUTH TABLE
VIN
L
UVLO
Inactive
Inactive
Active
DESAT
Internal TSD
VOUT
FLT
Open drain
Open drain
L
Notes
Normal operation − Output Low
Normal operation − Output High
L
L
L
L
L
L
H
L
H
X
X
UVLO activated − FLT Low (t
), Output Low
-
d3 FLT
(t
+ t
)
-
d3 FLT
d1−OUT
H
X
Inactive
Inactive
H
X
L
L
L
L
L
DESAT activated (only when V is High) − Output
IN
Low (t
), FLT Low
d2_OUT
H
Internal Thermal Shutdown − FLT Low (t
), Out-
-
d3 FLT
put Low (t
+ t
)
-
d3 FLT
d1−OUT
Thermal Shutdown
The NCx5707y also offers thermal shutdown function
that is primarily meant to self−protect the driver in the event
that the internal temperature gets excessive. Once the
(12 ms), the output is pulled low and many of the internal
circuits are turned off. The 12 ms delay is meant to allow the
controller to perform an orderly shutdown sequence as
appropriate. Once the temperature goes below the second
threshold, the part becomes active again.
temperature crosses the T threshold, the FLT output is
SD
activated after a delay of t
. After a delay of t
d3-FLT
d1−OUT
www.onsemi.com
20
NCD5707A, NCV5707A, NCD5707B, NCV5707B, NCD5707C, NCV5707C
PACKAGE DIMENSIONS
SOIC−8 NB
CASE 751−07
ISSUE AK
NOTES:
1. DIMENSIONING AND TOLERANCING PER
−X−
ANSI Y14.5M, 1982.
A
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
8
5
4
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
S
M
M
Y
B
0.25 (0.010)
1
K
−Y−
MILLIMETERS
DIM MIN MAX
INCHES
G
MIN
MAX
0.197
0.157
0.069
0.020
A
B
C
D
G
H
J
K
M
N
S
4.80
3.80
1.35
0.33
5.00 0.189
4.00 0.150
1.75 0.053
0.51 0.013
C
N X 45
_
SEATING
PLANE
1.27 BSC
0.050 BSC
−Z−
0.10
0.19
0.40
0
0.25 0.004
0.25 0.007
1.27 0.016
0.010
0.010
0.050
8
0.020
0.244
0.10 (0.004)
M
J
H
D
8
0
_
_
_
_
0.25
5.80
0.50 0.010
6.20 0.228
M
S
S
X
0.25 (0.010)
Z
Y
SOLDERING FOOTPRINT*
1.52
0.060
7.0
4.0
0.275
0.155
0.6
0.024
1.270
0.050
mm
inches
ǒ
Ǔ
SCALE 6:1
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative
onsemi Website: www.onsemi.com
◊
www.onsemi.com
相关型号:
©2020 ICPDF网 联系我们和版权申明