MN101CF95G [PANASONIC]
MN101CF95F;
| 型号： | MN101CF95G |
| 厂家： | 
PANASONIC |
| 描述： | MN101CF95F |
| 文件： | 总4页 (文件大小：309K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MN101CF95F, MN101CF95G
Type
MN101CF95F
MN101CF95G
Internal ROM type
ROM (byte)
FLASH
96K
128K
RAM (byte)
4K
6K
Package (Lead-free)
TQFP080-P-1212D (Under planning)
TQFP080-P-1212D (Under development)
[Standard]
0.2 µs (at 2.7 V to 3.6 V, 10 MHz)
0.5 µs (at 2.7 V to 3.6 V, 4 MHz)
62.5 µs (at 2.7 V to 3.6 V, 32 kHz)
[Double speed]
Minimum Instruction
Execution Time
0.1 µs (at 2.7 V to 3.6 V, 10 MHz)
Interrupts
RESET, Watchdog, External 0 to 5, Timer 0 to 8, Time base, Serial 0 reception, Serial 0 transmission, Serial 1 reception, Serial
1 transmission, Serial 2, Serial 3, Serial 4 reception, Serial 4 transmission, Automatic transfer finish, A/D conversion finish, Key
interrupts (12 lines)
Timer Counter
Timer counter 0 : 8-bit × 1
(square-wave/8-bit PWM output, event count, pulse width measurement, serial clock output, real-time output control,
generation of remote control carrier)
Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of
XI oscillation clock frequency; external clock input
Interrupt source ........... coincidence with compare register 0
Timer counter 1 : 8-bit × 1 (square-wave output, event count, synchronous output event, serial clock output)
Clock source................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of
XI oscillation clock frequency; external clock input
Interrupt source ........... coincidence with compare register 1
Timer counter 0, 1 can be cascade-connected.
Timer counter 2 : 8-bit × 1
(square-wave output, PWM output, event count, pulse width measurement, synchronous timer, serial clock output)
Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of
XI oscillation clock frequency; external clock input
Interrupt source ........... coincidence with compare register 2
Timer counter 0, 1, 2 can be cascade-connected.
Timer counter 3 : 8-bit × 1 (square-wave output, event count, serial clock output)
Clock source................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of
XI oscillation clock frequency; external clock input
Interrupt source ........... coincidence with compare register 3
Timer counter 2, 3 can be cascade-connected.
Timer counter 0, 1, 2, 3 can be cascade-connected.
Timer counter 4 : 8-bit × 1
(square-wave/8-bit PWM output, event count, pulse width measurement, real-time output control, serial clock output)
Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of
XI oscillation clock frequency; 1/1 of external clock input frequency
Interrupt source ........... coincidence with compare register 4
Timer counter 5 : 8-bit × 1
(square-wave/8-bit PWM output, event count, pulse width measurement, serial clock output)
Clock source................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of
XI oscillation clock frequency; external clock input
Interrupt source ........... coincidence with compare register 5
Timer counter 4, 5 can be cascade-connected.
MAD00053CEM
MN101CF95F, MN101CF95G
Timer counter 6 : 8-bit freerun timer
Clock source................ 1/1 of system clock frequency; 1/1, 1/128, 1/8192 of OSC oscillation clock frequency; 1/1, 1/128, 1/8192
of XI oscillation clock frequency
Interrupt source ........... coincidence with compare register 6
Timer counter 7 : 16-bit × 1
(square-wave/16-bit PWM output, cycle / duty continuous variable, event count, synchronous output evevt, pulse width
measurement, input capture, real-time output control)
Clock source................ 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC oscillation clock frequency; 1/1,
1/2, 1/4, 1/16 of external clock input frequency
Interrupt source ........... coincidence with compare register 7 (2 lines)
Timer counter 8 : 16-bit × 1
(square-wave output, PWM output (duty continuous variable), event count, pulse width measurement, input capture)
Clock source................ 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC oscillation clock frequency; 1/1,
1/2, 1/4, 1/16 of external clock input frequency
Interrupt source ........... coincidence with compare register 8 (2 lines)
Time base timer (one-minute count setting)
Clock source................ 1/1 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency
Interrupt source ........... 1/128, 1/256, 1/512, 1/1024, 1/8192, 1/32768 of clock source frequency
Watchdog timer
Interrupt source ........... 1/65536, 1/262144, 1/1048576 of system clock frequency
Serial interface
Serial 0 : synchronous type / UART (full-duplex) × 1
Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 1, 2; 1/2, 1/4, 1/16, 1/64 of OSC
oscillation clock frequency
Serial 1 : synchronous type / UART (full-duplex) × 1
Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 2, 3; 1/2, 1/4, 1/16, 1/64 of OSC
oscillation clock frequency
Serial 2 : synchronous type / multi-master I²C × 1
Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 3, 4; 1/2, 1/4, 1/16, 1/32 of OSC
oscillation clock frequency
Serial 3 : synchronous type / single-master I²C × 1
Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 4, 5; 1/2, 1/4, 1/16, 1/32 of OSC
oscillation clock frequency
Serial 4 : synchronous type / UART (full-duplex) × 1
Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 0, 5; 1/2, 1/4, 1/16, 1/64 of OSC
oscillation clock frequency
DMA controller
Max. Transfer cycles : 255
Starting factor : various types of interrupt, software
Transfer mode : 1-byte transfer, word transfer, burst transfer
I/O Pins
I/O
67
Common use , Specified pull-up resistor available, Input/output selectable (bit unit)
A/D converter
10-bit × 11-ch. (with S/H)
Special Ports
Buzzer output, remote control carrier signal output, high-current drive port
Development tools
In-circuit Emulator
PX-ICE101C/D+PX-PRB101C95-TQFP080-P-1212D
MAD00053CEM
Pin Assignment
TM4IO, SDO6, P76
TM5IO, SDO7, P77
LED7, P87
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
P25, IRQ5, TM7IOA
P24, IRQ4
P23, IRQ3
P22, IRQ2
P21, IRQ1
P20, IRQ0
P36
P35, SBT4
P34, SBI4, RXD4
P33, SBO4, TXD4
P32, TM3IO
P31, TM2OB
P30, TM2IOA
P15, SBT2, SCL2, SBT0B
P14, SBI2, SBI0B, RXD0B
P13, SBO2, SDA2, SBO0B, TXD0B
P12, SBT1A
P11, SBI1A, RXD1A
P10, SBO1A, TXD1A
P02, SBT3, SCL3, BUZZER
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
LED6, P86
SBT0A, LED5, P85
RXD0A, SBI0A, LED4, P84
TXD0A, SBO0A, LED3, P83
LED2, P82
LED1, P81
LED0, P80
KEY12, P44
KEY13, P45
KEY14, P46
KEY15, P47
VREF-
AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4
MN101CF95F
MN101CF95G
TQFP080-P-1212D
MAD00053CEM
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other
company which may arise as a result of the use of technical information described in this book.
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
– Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-
ucts may directly jeopardize life or harm the human body.
– Any applications other than the standard applications intended.
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita
Electric Industrial Co., Ltd. Industrial Co., Ltd.
相关型号：
MN101CFA7D
Microcontroller, 8-Bit, FLASH, 10MHz, CMOS, PQFP48, 7 X 7 MM, LEAD FREE, PLASTIC, QFP-48
PANASONIC
MN101CP28DHT
Microcontroller, 8-Bit, OTPROM, 20MHz, CMOS, PQFP80, 14 X 14 MM, LEAD FREE, PLASTIC, LQFP-80
PANASONIC
MN101CP38C
Microcontroller, 8-Bit, OTPROM, 20MHz, CMOS, PQFP100, 14 X 14 MM, LEAD FREE, PLASTIC, LQFP-100
PANASONIC
©2020 ICPDF网 联系我们和版权申明