MN101DF06Z [PANASONIC]
Microcontroller, 8-Bit, FLASH, 14.32MHz, CMOS, PQFP100, 18 X 18 MM, LEAD FREE, PLASTIC, QFP-100;
| 型号： | MN101DF06Z |
| 厂家： | 
PANASONIC |
| 描述： | Microcontroller, 8-Bit, FLASH, 14.32MHz, CMOS, PQFP100, 18 X 18 MM, LEAD FREE, PLASTIC, QFP-100 时钟 微控制器 外围集成电路 |
| 文件： | 总4页 (文件大小：341K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MN101D06 Series
Type
MN101D06F
MN101D06G
Mask ROM
128K
MN101D06H
MN101DF06Z
FLASH
224K
Internal ROM type
ROM (byte)
96K
3K
160K
5K
RAM (byte)
4K
6K
Package (Lead-free)
QFP100-P-1818B
0.1397 µs (at 4.0 V to 5.5
V, 14.32 MHz)
71.5 µs (at 3.0 V to 5.5
V, 14.32 MHz internal
frequency division)
61 µs (at 2.5 V to 5.5 V,
32.768 kHz)
[When using main clock]
0.1397 µs (at 4.0 V to 5.5 V, 14.32 MHz)
Minimum Instruction
Execution Time
71.5 µs (at 3.0 V to 5.5 V, 14.32 MHz internal frequency division)
[When using sub clock]
61 µs (at 2.2 V to 5.5 V, 32.768 kHz)
Interrupts
RESET. Runaway. External 0 to 4. Key input (P50 to P54). Timer 0 to 4. Timer 6. Timer 7. Capstan FG. Control. HSW. Cylinder(Drum)
FG. Servo V-sync. Synchronous output. OSD. XDS. Serial 0 to 2. A/D (common with PWM 4 reference frequency). OSDV-sync
Timer Counter
8-bit timer × 1 or 4-bit timer × 2
Timer 7 ..................Timer function. Event count
16-bit timer × 6
Timer 0 ..................Timer function. Max. 2 s or max. 36 h at cascade-connecting with timer 6
Timer 1 ..................Timer function. Linear timer counter function
Timer 2 ..................Timer function. Input capture. Duty judgment of CTL signal (VISS/VASS detection function)
Timer 3 ..................Timer function. Detection of serial indexing. Generation of remote control output carrier frequency
Timer 4 ..................Timer function. Event count (P15 input). Serial transfer clock output
Timer 6 ..................Clock function (max. 2 s)
19-bit timer × 1
Timer 5 ..................Watchdog. Stable oscillation waiting function
Serial interface
Synchronous type/Start-stop synchronous type × 1: Serial 0 (8-bit)
Serial 0...................Transfer direction of MSB/LSB selectable
Synchronous type/Remote control transmission/Simple remote control receive × 1: Serial 1 (8-bit)
Serial 1...................Transfer direction of MSB/LSB selectable. Start condition function
I2C × 1: Serial 2 (8-bit)
Serial 2...................Master transmission/reception. Slave transmission/reception
OSD
OSD mode: Accommodation with menu (internal synchronous) or super impose (external synchronous) display
Applicable broadcasting system......NTSC. PAL. PAL-M. PAL-N
Screen configuration .......... 24 characters × 2n rows (n = 1 to 6)
Character type .......Max. 512 character types (variable, incude special characters)
Character size ........12 dots × 18 dots (vertical direction: 1 dot for 2H at not enlargement)
Enlarged characters .......Each × 2, × 3 or × 4 settings in horizontal and vertical
Character interpolation....... None
Line background color....... 8-hue settable (settable in the row unit at menu display)
Line background intensity.. 8 gradations settable in the row unit (at output of composite video signal)
Screen background color.... 8-hue settable (at output of composite video signal menu display)
Character color ......White (at output of composite video signal)
Character intensity ........8 gradations settable in the row unit (at output of composite video signal)
Frame function ......1-dot frame in 4 or 8 directions
Frame intensity......4 gradations settable in the row unit (at output of composite video signal)
Box shade function........Settable in the character unit (at output of composite video signal with 129 or more characters (character types))
Blinking.................None (covered by software)
Inverted character..........Settable in the character unit
Halftone.................Settable in the row unit in 2 intensity gradations (at output of external synchronous composite video signal)
MAD00029KEM
MN101D06F, MN101D06G, MN101D06H, MN101DF06Z
CCD mode: Supports Closed Caption in the U.S.A.
Screen configuration .......... 32 characters × 16 rows
Character type .......Max. 128 character types (variable)
Character size ........12 × 26 dots (Vertical direction : 1 dot for 1H, including 8 dots in the underlined area)
Enlarged characters .......None
Character interpolation....... None
Line background color....... 8-hue settable
Line background intensity.. 8 gradations settable in the row unit (at output of composite video signal)
Screen background color.... 8-hue settable (at output of composite video signal)
Character color ......8 colors (at RGB output). White (at output of composite video signal)
Character intensity ........8 gradations settable in the row unit (at output of composite video signal)
Frame function ......None
Box shade function........None
Inverted character..........None
Halftone.................Settable in the row unit in 2 intensity gradations (at output of external synchronous composite video signal)
Others ....................Underline. Italic. Blinking function. Scroll
Common
Input ......................Composite video signal input (output level:1 V[p-p] / 2 V[p-p])
Clamp method .......Sync tip clamp. Clamp level in 4 levels
Output....................Composite video output. Digital output (6 pins)
Measure against image fluctuation......Built-in AFC circuit
Dot clock ...............1/2 of OSC oscillation clock (automatic phase adjustment)
XDS
Built-in U.S. closed caption data slicer: Optional 2 line data can be extracted
I/O Pins
I/O
75 : Common use: 66
2 : Common use: 2
Input
A/D converter
8-bit × 13 channels (without S/H)
PWM
13-bit × 2 channels (at repetition cycle 572 µs at 14.32 MHz)
10-bit × 2 channels (at repetition cycle 71.5 µs at 14.32 MHz)
8-bit × 1 channels (at repetition cycle 71.5 ms, 0.572 ms, 1.14 ms, 2.29 ms at 14.32 MHz)
ICR
18-bit × 6 channels
OCR
16-bit × 2: 8-bit synchronous output. 4-bit 3-state synchronous output
16-bit × 1: Weak electric field V-sync backup.
16-bit × 1: Rec CTL
Special Ports
Buzzer output. 3-state output VLP pin. Remote control reception
CTL signal input terminal. Capstan FG inputterminal. Sylinder(Durm) PG/FG input terminals. Head Amp/Rortary control output
terminals
Output of 1/2 OSC oscillation clock (2 V[p-p]). Output of 1/4 OSC oscillation clock (1 V[p-p])
ROM Correction
Correcting address designation: Up to 3 addresses possible
Correction method: Correction program being saved in internal RAM
MAD00029KEM
Electrical Charactreistics (Supply current)
Limit
typ
Parameter
Symbol
Condition
Unit
min
max
IDD1
IDD2
14.32 MHz oscillation without load. VDD = 5 V
60
2
100
mA
mA
Operating supply current
1/1024 of 14.32 MHz operation without load. VDD = 3.0 V
5
Stop of 14.32 MHz oscillation
Operating supply current
Supply current at STOP
IDD3
50
100
µA
32 kHz oscillation operation without load. VDD = 2.7 V
IDSP
Stop of oscillation without load. VDD = 5 V. Ta = 55 °C
10
15
µA
IDHT0 14.32 MHz oscillation without load. VDD = 5 V
5
5
mA
Supply current at HALT
Stop of 14.32 MHz oscillation
IDHT1
20
µA
32 kHz oscillation operation without load. VDD = 2.7 V
Ta = 25 °C±2 °C. VSS = 0 V
Electrical Charactreistics (A/D converter characteristics)
Limit
Unit
Parameter
Symbol
Condition
min
typ
max
Conversion relative error
A/D conversion time
Analog input voltage
LSB
µs
∆NLAD
±3
tAD
fosc = 14.32 MHz
8
5
V
Ta = 25 °C±2 °C. VDD = 5.0 V. VSS = 0 V
Pin Assignment
QFP100-P-1818B
CO
TPZ
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
CVIN2
CVIN
AD11
AD10
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
P77
VSS2
CVOUT
HSYNC
VSYN
OSCO2
OSCI2
SXI
XO
XI
VSS
OSCI
OSCO
VDD
P76
SBUFD0
PWM0
PWM1
SBUFD1
SBUFD2
SBUFD3
SBUFD4
SBUFD5
SBUFD6
SBUFD7
P75
P74
P73
P72
P71
P70
ROTA
HAMP
DENV
MAD00029KEM
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any
other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any
other company which may arise as a result of the use of technical information described in this book.
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
– Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-
ucts may directly jeopardize life or harm the human body.
– Any applications other than the standard applications intended.
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company.
20080805
相关型号：
MN101DF06ZAF
Microcontroller, 8-Bit, FLASH, 14.32MHz, CMOS, PQFP100, 18 X 18 MM, LEAD FREE, PLASTIC, QFP-100
PANASONIC
MN101DF07K
Microcontroller, 8-Bit, FLASH, 14.32MHz, CMOS, PQFP112, 20 X 20 MM, LEAD FREE, PLASTIC, LQFP-112
PANASONIC
MN101DF08GAL
Microcontroller, 8-Bit, FLASH, 14.32MHz, CMOS, PQFP80, 14 X 14 MM, LEAD FREE, PLASTIC, LQFP-80
PANASONIC
MN101DF09GAF
Microcontroller, 8-Bit, FLASH, MN101C00 CPU, 14.32MHz, CMOS, PQFP100, 18 X 18 MM, LEAD FREE, PLASTIC, QFP-100
PANASONIC
MN101DP02JAC
Microcontroller, 8-Bit, UVPROM, 14.32MHz, CMOS, PQFP100, 18 X 18 MM, PLASTIC, QFP-100
PANASONIC
MN101DP02JAF
Microcontroller, 8-Bit, OTPROM, 14.32MHz, CMOS, PQFP100, 18 X 18 MM, PLASTIC, QFP-100
PANASONIC
©2020 ICPDF网 联系我们和版权申明