PT7C4339UE [PERICOM]
Real-time Clock Module;型号: | PT7C4339UE |
厂家: | PERICOM SEMICONDUCTOR CORPORATION |
描述: | Real-time Clock Module |
文件: | 总22页 (文件大小:870K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PT7C4339/4339C
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Real-time Clock Module
Features
Description
Real-Time Clock (RTC) Including Time (Seconds,
Minutes and Hours) and Calendar (Day, Date,
Month and Year with Leap-Year Compensation
Valid Up to 2100) counter functions (BCD code)
Available in a Surface-Mount Package with an
Integrated Crystal (Only for PT7C4339C)
I2C Serial Interface supports I2C-Bus's high speed
mode (400 kHz)
The PT7C4339 real-time clock is a low-power
clock/calendar device with two programmable time-of-
day alarms and a programmable square-wave output.
Address and data are transferred serially through an I2C
bus. The clock/calendar provides seconds, minutes,
hours, day, date, month, and year information. The date
at the end of the month is automatically adjusted for
months with fewer than 31 days, including corrections
for leap year. The clock operates in either the 24-hour or
12-hour format with AM/PM indicator. The PT7C4339
has a build-in power-sense circuit that detects power
failures and automatically switch to the backup supply,
maintaining time, date, and alarm operation.
Programmable square wave output signal, defaults
to 32 kHz on Power-up
Two Time-of-Day Alarms
Oscillator Stop Flag
Automatic Power-Fail Detect and Switch Circuitry
Temperature Range: -40°C to +85°C
Package: MSOP-8L and SOIC-8L for PT7C4339
TDFN4x4-8L for PT7C4339C
Pin Configuration
PT7C4339
PT7C4339C
Applications
1
X1
8
1
8
VCC
NC
NC
2
3
4
7
6
5
2
3
4
7
6
5
X2
SQW/INT
SCL
VBACKUP
GND
SCL
VBACKUP
SQW/INT
VCC
GND
SDA
SDA
SOIC-8
MSOP8
DFN4*4-8L
Table1. Diverse functions of RTC circuits
Item
Function
PT7C4339
PT7C4339C
Source
External crystal
External crystal
Integrated Crystal
1
Oscillator
Oscillator enable/disable
Oscillator fail detect
12-hour
24-hour
Time display
2
Time
Century bit
Time count chain enable/disable
Alarm interrupt output
3
4
5
6
Interrupt
2
2
Programmable square wave output (Hz)
1, 4.096k, 8.192k, 32.768k
1, 4.096k, 8.192k, 32.768k
Communication
2-wire I2C bus
Power failure detect
2015-08-0008
PT0508-1
08/24/15
1
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Pin Description
Pin No
Pin
Type
Description
Name
43394339C
Oscillator Circuit Input. Together with X1, 32.768kHz crystal is connected between them. Or
external clock input.
1
2
6
/
/
X1
X2
I
O
I
Oscillator Circuit Output. Together with X1, 32.768kHz crystal is connected between them.
When 32.768kHz external input, X2 must be float.
Serial Clock Input. SCL is used to synchronize data movement on the I2C serial interface. The
7
SCL
pull up voltage may be up to 5.5V regardless of the voltage on VCC
.
Serial Data Input/Output. SDA is the input/output pin for the 2-wire serial interface. The SDA
5
4
SDA
I/O
pin is open-drain output and requires an external pull-up resistor. The pull up voltage may be up to
5.5V regardless of the voltage on VCC
.
Secondary Power Supply. Supply voltage must be held between 1.3V and 3.7V for proper
operation. This pin can be connected to a primary cell, such as a lithium button cell. Additionally,
this pin can be connected to a rechargeable cell or a super cap when used in conjunction with the
trickle-charge feature. Diodes should not be placed in series between the backup source and the
VBACKUP input, or improper operation will result. If a backup supply is not required, VBACKUP must
be grounded.
VBACKU
3
2
O
P
Square-Wave/Interrupt Output. Programmable square-wave or interrupt output signal. It is an
open-drain output and requires an external pull up resistor. The pull up voltage may be up to 5.5V
regardless of the voltage on VCC. If not used, this pin may be left unconnected.
Power. When voltage is applied within normal limits, the device is fully accessible and data can be
written and read. When a backup supply is connected and VCC is below VPF, reads and writes are
inhibited. The timekeeping and alarm functions operate when the device is powered by VCC or
SQW
/INT
7
8
6
5
O
VCC
P
P
VBACKUP
.
4
/
3
1,8
GND
NC
Ground.
No Connect. These pins are not connected internally, but must be grounded for proper operation.
Maximum Ratings
StorageTemperature....................................................................................-55 Cto+125 C
o
o
Note:
o
o
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the
device. This is a stress rating only and functional
operation of the device at these or any other condi-
tions above those indicated in the operational sec-
tions of this specification is not implied. Exposure
to absolute maximum rating conditions for extended
periods may affect reliability.
AmbientTemperaturewithPowerApplied..............................................-40 Cto+85 C
SupplyVoltagetoGroundPotential(VCCtoGND)..................................-0.3Vto+6.0V
DCInput(AllOtherImputsexceptVCC&GND)...........................-0.3VtoVCC +0.3V
DCOutputVoltage(SDA,SQW/INTpins).............................................-0.3Vto+6.0V
PowerDissipation...................................................................320mW(dependonpackage)
o
LeadTemperature(soldering,10s)............................................................................+260 C
o
SolderingTemperature(reflow).................................................................................+260 C
Recommended Operating Conditions
Symbol
Description
Min
3.0
Type
Max
5.5
Unit
V
VCC
Supply Voltage
3.3
VBACKUP
VIH
Backup Supply Voltage
Input high level
1.3
3.0
3.7
V
0.7VCC
-0.3
-
VCC+0.3
0.3VCC
1.88
V
VIL
Input low level
-
1.72
-
V
VPF
Power-Fail Voltage
Operation Temperature
1.60
-40
V
TA
85
ºC
2015-08-0008
PT0508-1
08/24/15
2
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
DC Electrical Characteristics
Unless otherwise specified, VCC = MIN to MAX, VBACKUP=MIN to MAX, TA = -40 °C to +85 °C
Item
Sym.
ILI
Pin
Condition
Min
-1
Typ
Max
1
Units
VIN=VCC or
GND
Input Leakage
I/O Leakage
SCL
μA
ILO
SDA, SQW/INT
SQW/INT
-1
1
-
μA
IOL1
1.0
3.0
3.0
mA
Logic0 Out VOL= 0.4V; VCC> VCCMIN
IOL2
SDA,
1.5
-
-
mA
mA
Logic 0 Out VOL= 0.2V;
VBACKUP >= VBACKMIN
VCC absent,
BBSQI=1
IOL1
SQW/INT
0.25
VCC Active Current
ICCA
ICCS
(Note 1)
80
40
250
100
150
μA
μA
VCC = 3.3V
VCC = 5.5V
VCC Standby Current(Note 2)
Trickle-Charger Resistor Register10h
= A5h, VCC = Typ, VBACKUP= 0V
R1
R2
(Note 3)
200
Ω
Ω
Trickle-Charger Resistor Register10h
= A6h, VCC = Typ, VBACKUP = 0V
2000
Trickle-Charger Resistor Register10h
= A7h, VCC = Typ, VBACKUP = 0V
R3
4000
25
Ω
VBACKUP Leakage Current
IBKLKG
VBACKUP
100
nA
DC Electrical Characteristics
Unless otherwise specified, VCC = 0V, VBACKUP=MIN to MAX, TA = -40 °C to +85 °C
Item
Sym.
Condition
Min
Typ
Max
Units
VBACKUP Current, /EOSC=0, SQW Off
VBACKUP Current, /EOSC=0, SQW On
IBKOSC
IBKSQW
Note 4, Note5
Note 4
300
400
600
900
nA
nA
VBACKUP Current, /EOSC=1
IBKDR
Note6
10
100
nA
Note:
1. SCL clocking at max frequency = 400 kHz, VIL = 0.0V, VIH = VCC, trickle charger disabled.
2. Specified with 2-wire bus inactive, VIL = 0.0V, VIH = VCC, trickle charger disabled.
3. VCC must be less than 3.63V if 200Ω resistance is selected.
4. Using recommended crystal on X1 and X2.
5. Specified with the SQW function disabled by setting INTCN = 1.
6. Crystal oscillator is disabled.
2015-08-0008
PT0508-1
08/24/15
3
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
AC Electrical Characteristics
Sym
VHM
VHL
Description
Rising and falling threshold voltage high
Rising and falling threshold voltage low
Value
0.8 VCC
0.2 VCC
Unit
V
V
Signal
VHM
VLM
tr
tf
Over the operating range (Figure 1)
Symbol
Item
Min.
-
Typ.
Max.
400
-
-
-
-
-
-
-
Unit
kHz
s
s
ns
ns
s
s
s
s
s
s
s
fSCL
SCL clock frequency
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
tSU;STA
tHD;STA
tSU;DAT
tHD;DAT1
tHD;DAT2
tSU;STO
tBUF
tLOW
tHIGH
tr
START condition set-up time
START condition hold time
Data set-up time (RTC read/write)
Data hold time (RTC write)
Data hold time (RTC read)
STOP condition setup time
Bus idle time between a START and STOP condition
When SCL = "L"
0.6
0.6
200
35
0
0.6
1.3
1.3
0.6
-
-
-
When SCL = "H"
Rise time for SCL and SDA
Fall time for SCL and SDA
Allowable spike time on bus
Capacitance load for each bus line
I/O Capacitance (SDA, SCL)
Oscillator Stop Flag (OSF) Delay
0.3
0.3
50
400
10
100
tf
tSP*
CB
-
-
-
-
ns
pF
pF
ms
CI/O
*
TOSF
-
* Note: only reference for design
tSU;STA
S
Sr
P
SCL
tLOW
tHIGH
tHD;STA
tSP
fSCL
tBUF
SDA
tSU;DAT
tHD;STA
tSU;STO
tHD;STA
tHD;DAT
tSU;STA
S
P
Start condition
Stop condition
Sr
Restart condition
Figure1 I2C Timing
2015-08-0008
PT0508-1
08/24/15
4
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Functional Block Diagram
Alarm 1 Register
VCC
Power Failure Detect
Comparator 1
Comparator 2
(Sec, Min, Hour, Day/Date)
Trickle Charger Control
Alarm 2 Register
(Min, Hour, Day/Date)
VBACKUP
X1
CD
32.768
kHz
Time Counter
(Sec,Min,Hour,Day,Date,Month,Year)
OSC
Counter Chain
CG
X2
“C” version only
Address
Decoder
Address
Register
Control Register
SCL
SDA
I /O
Interface
(I2C)
Interrupt Control
Square Wave Output Control
Shift Register
SQW/INT
Oscillator Circuit
PT7C4339
The PT7C4339 uses an external 32.768 kHz crystal. Table1 specifies several crystal parameters for the external crystal. The
Block Diagram shows a functional schematic of the oscillator circuit. The startup time is usually less than 1 second when using a
crystal with the specified characteristics.
Table1 Crystal Specifications
Parameter
Symbol
fO
ESR
CL
Min
Typ
32.768
Max
Unit
kHz
k
Nominal Frequency
Series Resistance
Load Capacitance
-
-
-
-
70
-
-
6
pF
Note: The crystal, traces, and crystal input pins should be isolated from RF generating signals.
Clock Accuracy
The accuracy of the clock is dependent upon the accuracy of the crystal and the accuracy of the match between the capacitive
load of the oscillator circuit and the capacitive load for which the crystal was trimmed. Crystal frequency drift caused by
temperature shifts creates additional error. External circuit noise coupled into the oscillator circuit can result in the clock running
fast. Figure 2 shows a typical PC board layout for isolating the crystal and oscillator from noise.
PT7C4339C
The PT7C4339C integrates a standard 32,768Hz crystal in the package. Typical accuracy at nominal VCC and +25°C is
approximately ±10ppm.
2015-08-0008
PT0508-1
08/24/15
5
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Recommended Layout for Crystal (only for PT7C4339)
Figure 2 typical PC board layout for isolating the crystal and oscillator from noise
2015-08-0008
PT0508-1
08/24/15
6
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Functional Description
1. Overview of Functions
1.1. Clock function
CPU can read or write data including the year (last two digits), month, date, day, hour, minute, and second. Any (two-digit)
year that is a multiple of 4 is treated as a leap year and calculated automatically as such until the year 2100.
For PT7C4339 on a power-on reset (POR), the time and date are set to 00:00:00 01/01/00 (hh:mm:ss DD/MM/YY) and the
Day register is set to 01.
1.2. Alarm function
This device has two alarm system (Alarm 1 and Alarm 2) that outputs interrupt signals from SQW/INT to CPU when the
date, day of the week, hour, minute or second correspond to the setting. Each of them may output interrupt signal separately at a
specified time. The alarm is be selectable between on and off for matching alarm or repeating alarm.
1.3. Programmable square wave output
A square wave output enable bit controls square wave output at pin 7. Frequencies are selectable: 1, 4.096k, 8.192k, 32.768
kHz.
1.4. Interface with CPU
Data is read and written via the I2C bus interface using two signal lines: SCL (clock) and SDA (data).
Since the output of the I/O pin SDA is open drain, a pull-up resistor should be used on the circuit board if the CPU output I/O
is also open drain.
The SCL's maximum clock frequency is 400 kHz, which supports the I2C bus's high-speed mode.
1.5. Oscillator fail detect
When oscillator fail, PT7C4339 OSF bit will be set.
1.6. Oscillator enable/disable
Oscillator can be enabled or disabled at the same time by /EOSC bit.
2. Operation
The PT7C4339 operates as a slave device on the serial bus. Access is obtained by implementing a START condition and
providing a device identification code followed by data. Subsequent registers can be accessed sequentially until a STOP condition
is executed. The device is fully accessible and data can be written and read when VCC is greater than VPF. However, when VCC falls
below VPF, the internal clock registers are blocked from any access. If VPF is less than VBACKUP, the device power is switched from
VCC to VBACKUP when VCC drops below VPF. If VPF is greater than VBACKUP, the device power is switched from VCC to VBACKUP
when VCC drops below VBACKUP. The registers are maintained from the VBACKUP source until VCC is returned to nominal levels.
3. Power Control
The power-control function is provided by a precise, temperature-compensated voltage reference and a comparator circuit
that monitors the VCC level. The device is fully accessible and data can be written and read when VCC is greater than VPF. However,
when VCC falls below VPF, the internal clock registers are blocked from any access. If VPF is less than VBACKUP, the device power is
switched from VCC to VBACKUP when VCC drops below VPF. If VPF is greater than VBACKUP, the device power is switched from VCC
to VBACKUP when VCC drops below VBACKUP. The registers are maintained from the VBACKUP source until VCC is returned to nominal
levels (Table 2). After VCC returns above VPF, read and write access is allowed after tREC (Figure 1). On the first application of
power to the device the time and date registers are reset to 01/01/00 01 00:00:00 (MM/DD/YY DOW HH:MM:SS).
Table 2:
Power Control Supply Condition
VCC < VPF, VCC < VBACKUP
VCC < VPF, VCC > VBACKUP
VCC > VPF, VCC < VBACKUP
VCC > VPF, VCC > VBACKUP
Read/Write Access
Power by
VBACKUP
VCC
No
No
Yes
Yes
VCC
VCC
2015-08-0008
PT0508-1
08/24/15
7
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
4. Registers
4.1. Allocation of registers
Register definition
Addr.
Function
Seconds (00-59)
Minutes (00-59)
Hours (00-23 / 01-12)
Days of the week (01-07)
Dates (01-31)
(hex) *1
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
0
S40
S20
S10
S8
S4
S2
S1
0
M40
12, /24
0
M20
M10
H10
0
M8
H8
0
M4
H4
M2
H2
M1
H1
H20 or
P, /A
0
0
0
W4
D4
W2
D2
W1
D1
0
0
D20
0
D10
MO10
Y10
S10
D8
MO8
Y8
S8
Months (01-12)
Years (00-99)
Century
Y80
0
MO4
Y4
MO2
Y2
MO1
Y1
Y40
S40
M40
12, /24
Y20
S20
M20
Alarm 1: Seconds
Alarm 1: Minutes
Alarm 1: Hours
Alarm 1: Day, Date
Alarm 2: Minutes
Alarm 2: Hours
Alarm 2: Day, Date
Control
A1M1*2
A1M2*2
A1M3*2
A1M4*2
A2M2*3
A2M3*3
A2M4*3
/EOSC*4
OSF*9
TCS3
S4
S2
S1
M10
H10
M8
H8
M4
H4
M2
H2
M1
H1
H20 or
P, /A
0,
Day,
0,
0,
W4,
D4
W2,
D2
W1,
D1
/Date
D20
D10
D8
M40
M20
M10
H10
M8
H8
M4
H4
M2
H2
M1
H1
H20 or
P, /A
0,
12, /24
Day,
0,
0,
W4,
D4
W2,
D2
W1,
D1
/Date
D20
D10
D8
0
0
BBSQI
0
RS2*5
RS1*5
INTCN*6 A2IE*7
A1IE*7
Status
0
0
0
A2F*8
A1F*8
Trickle charger
TCS2
TCS1
TCS0
DS1
DS0
ROUT1
ROUT0
Caution points:
*1. PT7C4339 uses 8 bits for address. For excess 10H address, PT7C4339 will not respond (no acknowledge signal was given).
*2. Alarm 1 mask bits. Select alarm repeated rate when an alarm occurs.
*3. Alarm 2 mask bits. Select alarm repeated rate when an alarm occurs.
*4. Oscillator enable/disable bit.
*5. Square wave output frequency select.
*6. Interrupt output pin select bit.
*7. Alarm 1 and alarm 2 enable bits.
*8. Alarm 1 and alarm 2 flag bits.
*9. Oscillators stop flag.
*10. All bits marked with "0" are read-only bits. Their value when read is always "0".
2015-08-0008
PT0508-1
08/24/15
8
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
4.2. Control and status register
Addr.
Description
D7
D6
D5
D4
D3
D2
D1
D0
(hex)
Control
/EOSC
0
0
0
BBSQI
0
RS2
1
RS1
1
INTCN
0
A2IE
0
A1IE
0
0E
(default)
Status
OSF
1
0
0
0
0
0
0
0
0
0
0
A2F
A1F
0F
(default)
Undefined Undefined
1) Oscillator related bits
/EOSC
Enable oscillator bit.
/EOSC
Data
Description
Default
0
1
Starts the oscillator.
The oscillator is stopped.
Read / Write
2) BBSQI
Battery-Backed Square-Wave and Interrupt Enable bit.
BBSQI
Data
Description
Default
0
The SQW/INT pin goes high impedance when VCC falls below the power-fail trip point.
Read /
Write
Enables the square wave or interrupt output when VCC is absent and the PT7C4339 is being powered by
the VBACKUP pin.
1
3) Square wave frequency selection bits
RS2, RS1
Square wave Rate Select. These bits control the frequency of the square-wave output when the square wave has been enabled.
RS2, RS1
Data
00
SQW output freq. (Hz)
1
01
4.096k
8.192k
32.768k
Read / Write
10
Default
11
4) OSF
Oscillator Stop Flag
Logic 1 in this bit indicates that the oscillator either is stopped or was stopped for some period of time and may be used to judge
the validity of the clock and calendar data. This bit is set to logic 1 anytime that the oscillator stops. The following are examples of
conditions that can cause the OSF bit to be set:
1) The first time power is applied.
2) The voltage present on VCC is insufficient to support oscillation.
3) The /EOSC bit is turned off.
4) External influences on the crystal (e.g., noise, leakage, etc.).
This bit remains at logic 1 until written to logic 0.
2015-08-0008
PT0508-1
08/24/15
9
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5) Interrupt related bits
INTCN
Interrupt Output pin select bit. This bit controls the relationship between the two alarms and the interrupt output pins.
INTCN
Data
Description
A match between the timekeeping registers and the alarm 1 or alarm 2 registers activate the SQW/INT
pin (provided that the alarm is enabled).
1
Read/write
Default
0
In this configuration, a square wave is output on the SQW/INT pin.
A1IE
Alarm 1 Interrupt Enable.
A1IE
Data
Description
Default
0
The A1F bit does not initiate the SQW/INT signal.
Read/write
1
Permits the alarm 1 flag (A1F) bit in the status register to assert SQW/INT.
A1F
Alarm 1 Flag.
A1F
Data
Description
Default
Read / Write
0
The time does not match the alarm 1 registers.
A logic 1 in the Alarm 1 Flag bit indicates that the time matched the alarm 1 registers. If the A1IE bit is
a logic 1 and the INTCN bit is set to a logic 1, the SQW/INT pin is also asserted. A1F is cleared when
Read
1
written to logic 0. This bit can only be written to logic 0. Attempting to write to logic 1 leaves the value
unchanged.
A2IE
Alarm 2 Interrupt Enable.
A2IE
Data
Description
Default
0
The A2F bit does not initiate an interrupt signal.
Read/write
1
Permits the alarm 2 flag (A2F) bit in the status register to assert SQW/INT (when INTCN = 1).
A2F
Alarm 2 Flag.
A1F
Data
Description
Default
Read / Write
Read
0
The time does not match the alarm 2 registers.
A logic 1 in the Alarm 2 Flag bit indicates that the time matched the alarm 2 registers. If the A2IE bit
is a logic 1 and the INTCN bit is set to a logic 1, the SQW/INT pin is also asserted. A2F is cleared
1
when written to logic 0. This bit can only be written to logic 0. Attempting to write to logic 1 leaves
the value unchanged.
2015-08-0008
PT0508-1
08/24/15
10
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
4.3. Time Counter
Time digit display (in BCD code):
Second digits: Range from 00 to 59 and carried to minute digits when incremented from 59 to 00.
Minute digits: Range from 00 to 59 and carried to hour digits when incremented from 59 to 00.
Hour digits: See description on the /12, 24 bit. Carried to day and day-of-the-week digits when incremented from 11 p.m. to
12 a.m. or 23 to 00.
Addr.
Description
D7
D6
D5
D4
D3
D2
D1
D0
(hex)
Seconds
(default)
0
0
S40
S20
S10
S8
S4
S2
S1
00
Undefined Undefined Undefined Undefined Undefined Undefined Undefined
M40 M20 M10 M8 M4 M2 M1
Undefined Undefined Undefined Undefined Undefined Undefined Undefined
12, /24 H20 or P,/A H10 H8 H4 H2 H1
Undefined Undefined Undefined Undefined Undefined Undefined Undefined
Minutes
(default)
0
0
01
02
Hours
0
0
(default)
Note: Any registered imaginary time should be replaced with correct time, otherwise it will cause the clock counter malfunction.
12, /24 bit
This bit is used to select between 12-hour clock system and 24-hour clock system.
12, /24
Data
Description
0
1
24-hour system
12-hour system
Read / Write
This bit is used to select between 12-hour clock operation and 24-hour clock operation.
12, /24
Description
Hours register
24-hour clock
12-hour clock
24-hour clock
12-hour clock
72 ( PM 12)
61 ( PM 01 )
62 ( PM 02 )
63 ( PM 03 )
64 ( PM 04 )
65 ( PM 05 )
66 ( PM 06 )
67 ( PM 07 )
68 ( PM 08 )
69 ( PM 09 )
70 ( PM 10 )
71 ( PM 11 )
00
01
02
03
04
05
06
07
08
09
10
11
52 ( AM 12 )
41 ( AM 01 )
42 ( AM 02 )
43 ( AM 03 )
44 ( AM 04 )
45 ( AM 05 )
46 ( AM 06 )
47 ( AM 07 )
48 ( AM 08 )
49 ( AM 09 )
50 ( AM 10 )
51 ( AM 11 )
12
13
14
15
16
17
18
19
20
21
22
23
0
24-hour time display
1
12-hour time display
* Be sure to select between 12-hour and 24-hour clock operation before writing the time data.
4.4. Days of the week Counter
The day counter is a divide-by-7 counter that counts from 01 to 07 and up 07 before starting again from 01. Values that
correspond to the day of week are user defined but must be sequential (i.e., if 1 equals Sunday, then 2 equals Monday, and so on).
Illogical time and date entries result in undefined operation.
Addr.
Description
D7
D6
D5
D4
D3
D2
D1
D0
(hex)
Days of the week
(default)
0
0
0
0
0
0
0
0
0
0
W4
W2
W1
03
Undefined Undefined Undefined
2015-08-0008
PT0508-1 08/24/15
11
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
4.5. Calendar Counter
The data format is BCD format.
Day digits: Range from 1 to 31 (for January, March, May, July, August, October and December).
. Range from 1 to 30 (for April, June, September and November).
. Range from 1 to 29 (for February in leap years).
. Range from 1 to 28 (for February in ordinary years).
. Carried to month digits when cycled to 1.
Month digits: Range from 1 to 12 and carried to year digits when cycled to 1.
Year digits: Range from 00 to 99 and 00, 04, 08, … , 92 and 96 are counted as leap years.
Addr.
Description
D7
D6
D5
D4
D3
D2
D1
D0
(hex)
Dates
0
0
0
0
D20
D10
D8
D4
D2
D1
04
(default)
Undefined Undefined Undefined Undefined Undefined Undefined
Months
Century*1
Undefined
0
0
0
0
M10
Undefined Undefined Undefined Undefined Undefined
Y10 Y8 Y4 Y2 Y1
M8
M4
M2
M1
05
06
(default)
Years
Y80
Y40
Y20
(default)
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined
*1: The century bit is toggled when the years register overflows from 99 to 00.
4.6. Alarm Register
Alarm 1, Alarm 2 Register
Addr.
Description
D7
D6
D5
D4
D3
D2
D1
D0
Alarm 1: Seconds
(default)
A1M1*1
S40
S20
S10
S8
S4
S2
S1
07
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined
A1M2*1
M40 M20 M10 M8 M4 M2 M1
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined
A1M3*1
12, /24 H20 or P,/A H10 H8 H4 H2 H1
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined
Alarm 1: Minutes
(default)
08
09
Alarm 1: Hours
(default)
Day,
/Date*1
0,
0,
0,
W4,
D4
W2,
D2
W1,
D1
Alarm 1: Day, Date A1M4*1
D20
D10
D8
0A
(default)
Alarm 2: Minutes
(default)
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined
A2M2*2
M40 M20 M10 M8 M4 M2 M1
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined
A2M3*2
12, /24 H20 or P,/A H10 H8 H4 H2 H1
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined
0B
0C
Alarm 2: Hours
(default)
Day,
/Date*2
0,
0,
0,
W4,
D4
W2,
D2
W1,
D1
Alarm 2: Day, Date A2M4*2
D20
D10
D8
0D
(default)
Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined
*1 Note: Alarm mask bit, using to select Alarm 1 alarm rate.
*2 Note: Alarm mask bit, using to select Alarm 2 alarm rate.
2015-08-0008
PT0508-1
08/24/15
12
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
4.7. Alarm Function
Related register
Register definition
Addr.
(hex)
Function
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
00
01
02
03
04
07
08
09
0A
0B
0C
0D
0E
0F
Seconds
Minutes
Hours
0
S40
S20
S10
S8
S4
S2
S1
0
M40
12, /24
0
M20
M10
H10
0
M8
H8
0
M4
H4
W4
D4
S4
M2
H2
W2
D2
S2
M1
H1
W1
D1
S1
H20 or
A, /P
0
Days of the week
Dates
0
0
0
0
D20
S20
M20
D10
S10
M10
H10
D8
S8
M8
H8
Alarm 1: Seconds
Alarm 1: Minutes
Alarm 1: Hours
Alarm 1: Day, Date
Alarm 2: Minutes
Alarm 2: Hours
Alarm 2: Day, Date
Control
A1M1
A1M2
A1M3
A1M4
A2M2
A2M3
A2M4
/EOSC
OSF
S40
M40
12, /24
M4
H4
M2
H2
M1
H1
H20 or
A, /P
0,
Day,
0,
0,
W4,
D4
W2,
D2
W1,
D1
/Date
D20
D10
D8
M40
M20
M10
H10
M8
H8
M4
H4
M2
H2
M1
H1
H20 or
A, /P
0,
12, /24
Day,
0,
0,
W4,
D4
W2,
D2
W1,
D1
/Date
D20
D10
D8
0
0
BBSQI
0
RS2
0
RS1
0
INTCN
0
A2IE
A2F
A1IE
A1F
Status
Note: Alarm function does not support different hour system adopted in time and alarm register.
The PT7C4339 contains two time-of-day/date alarms. The alarms can be programmed (by the INTCN bit of the control
register) to operate in two different modes - each alarm can drive a common interrupt output. Bit 7 of each of the time-of-day/date
alarm registers are mask bits.
When all of the mask bits for each alarm are logic 0, an alarm only occurs when the values in the timekeeping registers 00h ~
04h match the values stored in the time-of-day/date alarm registers. The alarms can also be programmed to repeat every second,
minute, hour, day, or date. Table3 and Table4 show the possible settings.
The Day, /Date bits (bit 6 of the alarm day/date registers) control whether the alarm value stored in bits 0 ~ 5 of that register
reflects the day of the week or the date of the month. If the bit is written to logic 0, the alarm is the result of a match with date of
the month. If the bit is written to logic 1, the alarm is the result of a match with day of the week.
When the PT7C4339 register values match alarm register settings, the corresponding alarm flag (A1F or A2F) bit is set to
logic 1. If the corresponding alarm interrupt enable (A1IE or A2IE) is also set to logic 1, the alarm condition activates one of the
interrupt output (SQW/INT) signals. The match is tested on the once-per-second update of the time and date registers.
2015-08-0008
PT0508-1
08/24/15
13
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Table3. Alarm 1 Mask Bits
Alarm 1 register mask bits
Day,
Alarm rate
/Date
A1M4 A1M3 A1M2 A1M1
1
1
1
1
0
0
1
1
1
0
0
0
0
1
0
0
0
0
0
Alarm once per second
0
1
1
Alarm when seconds match
1
Alarm when minutes and seconds match
Alarm when hours, minutes, and seconds match
Alarm when date, hours, minutes, and seconds match
Alarm when day, hours, minutes, and seconds match
Ignored.
0
0
0
Others
Table4. Alarm 2 Mask Bits
Alarm 2 register mask bits
Day,
Alarm rate
/Date
A2M4
A2M3
A2M2
1
1
1
0
0
1
1
0
0
0
1
0
0
0
0
Alarm once per minute (00 seconds of every minute)
Alarm when minutes match
0
1
Alarm when hours, minutes
Alarm when date, hours, and minutes match
Alarm when day, hours, and minutes match
Ignored.
Others
4.8. Trickle Charger Register (10h)
The simplified schematic in Figure 5 shows the basic components of the trickle charger. The trickle-charge select (TCS) bits (bits
4 to 7) control the selection of the trickle charger. To prevent accidental enabling, only a pattern on 1010 enables the trickle
charger. All other patterns disable the trickle charger. The trickle charger is disabled when power is first applied. The diode-select
(DS) bits (bits 2 and 3) select whether or not a diode is connected between VCC and VBACKUP. The ROUT bits (bits 0 and 1)
select the value of the resistor connected between VCC and VBACKUP. Table 5 shows the bit values.
Table5. Trickle Charger Register (10h)
BIT 7
TCS3
X
X
X
1
1
1
1
1
BIT 6
TCS2
X
X
X
0
0
0
0
0
BIT 5
TCS1
X
X
X
1
1
1
1
1
BIT 4
TCS0
X
X
X
0
0
0
0
0
BIT 3
DS1
0
1
X
0
1
0
1
0
BIT 2
DS0
0
1
X
1
0
1
0
1
BIT 1
ROUT1
BIT 0
ROUT0
Function
X
X
0
0
0
1
1
1
1
0
X
X
0
1
1
0
0
1
1
0
Disabled
Disabled
Disabled
No diode, 200Ω resistor
One diode, 200Ω resistor
No diode, 2kΩ resistor
One diode, 2kΩ resistor
No diode, 4kΩ resistor
One diode, 4kΩ resistor
Initial power-up values
1
0
0
0
1
0
0
0
1
0
0
0
Warning: The ROUT value of 200Ω must not be selected whenever VCC is greater than 3.63V.
The user determines diode and resistor selection according to the maximum current desired for battery or super cap charging.
The maximum charging current can be calculated as illustrated in the following example. Assume that a 3.3V system power
supply is applied to VCC and a super cap is connected to VBACKUP. Also assume that the trickle charger has been enabled with
a diode and resistor R2 between VCC and VBACKUP. The maximum current IMAX would therefore be calculated as follows:
IMAX = (3.3V - diode drop) / R2 ≈ (3.3V - 0.7V) / 2kΩ ≈ 1.3mA
As the super cap or battery charges, the voltage drop between VCC and VBACKUP decreases and therefore the charge
current decreases.
2015-08-0008
PT0508-1
08/24/15
14
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Figure 5: Programmable Trickle Charger
5. I2C Bus Interface
5.1. Overview of I2C-BUS
The I2C bus supports bi-directional communications via two signal lines: the SDA (data) line and SCL (clock) line. A combination
of these two signals is used to transmit and receive communication start/stop signals, data signals, acknowledge signals, and so on.
Both the SCL and SDA signals are held at high level whenever communications are not being performed. The starting and
stopping of communications is controlled at the rising edge or falling edge of SDA while SCL is at high level. During data
transfers, data changes that occur on the SDA line are performed while the SCL line is at low level, and on the receiving side the
data is captured while the SCL line is at high level. In either case, the data is transferred via the SCL line at a rate of one bit per
clock pulse. The I2C bus device does not include a chip select pin such as is found in ordinary logic devices. Instead of using a
chip select pin, slave addresses are allocated to each device and the receiving device responds to communications only when its
slave address matches the slave address in the received data.
5.2. System Configuration
All ports connected to the I2C bus must be either open drain or open collector ports in order to enable AND connections to
multiple devices.
SCL and SDA are both connected to the VCC line via a pull-up resistance. Consequently, SCL and SDA are both held at high
level when the bus is released (when communication is not being performed).
2015-08-0008
PT0508-1
08/24/15
15
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Vcc
RP
RP
SDA
SCL
Master
MCU
Slave
RTC
Other Peripheral
Device
Note: When there is only one master, the MCU is ready for driving SCL to "H" and RP of SCL may not required.
Fig2. System configuration
5.3. Starting and Stopping I2C Bus Communications
Fig3. Starting and stopping on I2C bus
1) START condition, repeated START condition, and STOP condition
a) START condition
SDA level changes from high to low while SCL is at high level
b) STOP condition
SDA level changes from low to high while SCL is at high level
c) Repeated START condition (RESTART condition)
In some cases, the START condition occurs between a previous START condition and the next STOP condition, in which
case the second START condition is distinguished as a RESTART condition. Since the required status is the same as for the
START condition, the SDA level changes from high to low while SCL is at high level.
2) Data Transfers and Acknowledge Responses during I2C-BUS Communication
a) Data transfers
Data transfers are performed in 8-bit (1 byte) units once the START condition has occurred. There is no limit on the amount
(bytes) of data that are transferred between the START condition and STOP condition.
The address auto increment function operates during both write and read operations.
Updating of data on the transmitter (transmitting side)'s SDA line is performed while the SCL line is at low level.
2015-08-0008
PT0508-1
08/24/15
16
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
The receiver (receiving side) captures data while the SCL line is at high level.
*Note: with caution that if the SDA data is changed while the SCL line is at high level, it will be treated as a START, RESTART,
or STOP condition.
b) Data acknowledge response (ACK signal)
When transferring data, the receiver generates a confirmation response (ACK signal, low active) each time an 8-bit data
segment is received. If there is no ACK signal from the receiver, it indicates that normal communication has not been established.
(This does not include instances where the master device intentionally does not generate an ACK signal.)
Immediately after the falling edge of the clock pulse corresponding to the 8th bit of data on the SCL line, the transmitter
releases the SDA line and the receiver sets the SDA line to low (= acknowledge) level.
SCL from Master
8
9
2
1
SDA from transmitter
(sending side)
Release SDA
Low active
ACK signal
SDA from receiver
(receiving side)
After transmitting the ACK signal, if the Master remains the receiver for transfer of the next byte, the SDA is released at the
falling edge of the clock corresponding to the 9th bit of data on the SCL line. Data transfer resumes when the Master becomes the
transmitter.
When the Master is the receiver, if the Master does not send an ACK signal in response to the last byte sent from the slave,
that indicates to the transmitter that data transfer has ended. At that point, the transmitter continues to release the SDA and awaits
a STOP condition from the Master.
5.4. Slave Address
The I2C bus device does not include a chip select pin such as is found in ordinary logic devices. Instead of using a chip select
pin, slave addresses are allocated to each device.
All communications begin with transmitting the [START condition] + [slave address (+ R/W specification)]. The receiving
device responds to this communication only when the specified slave address it has received matches its own slave address.
Slave addresses have a fixed length of 7 bits. See table for the details.
An R/W bit is added to each 7-bit slave address during 8-bit transfers.
Table
Slave address
bit 4
R / W bit
bit 0
Operation
Transfer data
bit 7
bit 6
bit 5
bit 3
bit 2
bit 1
Read
D1 h
D0 h
1 (= Read)
0 (= Write)
1
1
0
1
0
0
0
Write
2015-08-0008
PT0508-1
08/24/15
17
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
5.5. I2C Bus’s Basic Transfer Format
S
Start indication
P
Stop indication
A
A
RTC Acknowledge
Sr
Restart indication
Master Acknowledge
1) Write via I2C bus
Addr. setting
bit bit bit
bit bit bit bit bit
Slave address (7 bits)
S
A
A
A
P
write
0
7
6
5
4
3
2
1
0
1
1
0
1
0
0
0
Start
Stop
A
C
K
A
C
K
A
C
K
Slave address + write specification
Address
Specifies the write start address.
Write data
2) Read via I2C bus
(1) Standard read
Slave address (7 bits)
Addr. setting
S
A
A
write
1
1
0
1
0
0
0
0
Start
A
C
K
A
C
K
Slave address + write specification
Address
Specifies the read start address.
bit bit bit bit bit bit bit bit
bit bit
bit bit bit bit bit bit
Slave address (7 bits)
Sr
A
A
/A
P
Read
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
1
1
0
1
0
0
0
1
Restart
A
C
K
A
C
K
Stop
N
O
Data read (1)
Data is read from the specified start
address and address auto increment.
Data read (2)
Address auto increment to set the
address for the next data to be read.
Slave address + read specification
A
C
K
2015-08-0008
PT0508-1
08/24/15
18
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
(2) Simplified read
bit bit bit bit bit bit bit bit
bit bit
bit bit bit bit bit bit
Slave address (7 bits)
S
A
A
/A
P
Read
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
1
1
0
1
0
0
0
1
Start
A
C
K
A
C
K
Stop
N
O
Data read (2)
Data read (1)
Slave address + read specification
Address register auto increment to set
the address for the next data to be
read.
Data is read from the address pointed
by the internal address register and
address auto increment.
A
C
K
Note:
1. The above steps are an example of transfers of one or two bytes only. There is no limit to the number of bytes transferred
during actual communications.
2. 49H, 4AH are used as test mode address. Customer should not use the addresses.
2015-08-0008
PT0508-1
08/24/15
19
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Mechanical Information
MSOP-8L
2015-08-0008
PT0508-1
08/24/15
20
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
SOIC-8L
2015-08-0008
PT0508-1
08/24/15
21
PT7C4339/4339C
Real-time Clock Module
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
TDFN4.0x4.0-8L
Ordering Information
Part No.
Package Code
Package
PT7C4339UE
U
U
Lead free and Green 8-pin MSOP
Lead free and Green 8-pin MSOP Tape/Reel
Lead free and Green 8-pin SOIC
PT7C4339UEX
PT7C4339WE
PT7C4339WEX
PT7C4339CZSAE*
W
W
Lead free and Green 8-pin SOIC Tape/Reel
Lead free and Green 8-pin TDFN4.0x4.0
ZSA
Note:
E = Pb-free and Green
Adding X Suffix= Tape/Reel
* Pls connect Pericom for available.
Pericom Semiconductor Corporation 1-800-435-2336 www.pericom.com
Pericom reserves the right to make changes to its products or specifications at any time, without notice, in order to improve design or performance and to supply
the best possible product. Pericom does not assume any responsibility for use of any circuitry described other than the circuitry embodied in Pericom product. The
company makes no representations that circuitry described herein is free from patent infringement or other rights, of Pericom.
2015-08-0008
PT0508-1
08/24/15
22
相关型号:
PT7C4363WE
Real Time Clock, Non-Volatile, 1 Timer(s), CMOS, PDSO8, GREEN, MS-012E/AA, SOIC-8
PERICOM
PT7C4363WEX
Real Time Clock, Non-Volatile, 1 Timer(s), CMOS, PDSO8, GREEN, MS-012E/AA, SOIC-8
PERICOM
©2020 ICPDF网 联系我们和版权申明