MPB125-4350 [POWER-ONE]
High Power Density in Industry Standard 3 x 5 Footprint; 在行业标准的高功率密度3× 5足迹
| 型号： | MPB125-4350 |
| 厂家： | 
POWER-ONE |
| 描述： | High Power Density in Industry Standard 3 x 5 Footprint |
| 文件： | 总4页 (文件大小：126K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MPB125 SERIES
DESCRIPTION
The MPB125 series incorporates patented high efficiency circuitry,
high power density and active Power Factor Correction (PFC) to meet
the requirements of networking and data communications systems, as
well as commercial and industrial configurations.
output power is available with as few as 130 Linear Feet per Minute
(LFM) forced-air cooling.
The MPB125 product line is approved to the latest international
regulatory standards, and displays the CE Mark.
Dual output units deliver a regulated main output plus a second 12V
output for fans or other system functions. Multiple output models
provide tightly regulated DC power in a variety of configurations.
The MPB125 is rated for convection as well as forced-air cooling. Full
FEATURES
•
•
•
•
•
•
High Power Density in Industry Standard 3" x 5" Footprint
Power Factor Correction (PFC) Meets EN61000-3-2
Main Output Remote Sense
Power Good Signals
CE Marked to Low Voltage Directive
Input Transient & ESD Compliance to
EN61000-4-2/-3/-4/-5
MULTIPLE OUTPUT MODEL SELECTION CHART -
80 Watts Convection Cooling, 125 Watts Forced-Air Cooling
OUTPUT
VOLTAGE
(VOLTS)
MAXIMUM OUTPUT
CURRENT (AMPS),
130 LFM (NOTE 2)
TOTAL
REGULATION
%
RIPPLE & NOISE
% pk-pk
MODEL
REGULATION RANGE
(NOTE 3)
+5V
+12V
+12V
+12V
+15V
+12V
+24V
+12V
+48V
+12V
+5V
+12V
-12V
+2.5V
+5V
+12V
-12V
+±.±V
+5V
25A
0.5A
10.5A
0.5A
8.±A
0.5A
5.2A
0.5A
2.6A
0.5A
±±3
±53
±±3
±53
±±3
±53
±±3
±53
±±3
±53
±±3
±53
±±3
±±3
±±3
±53
±±3
±±3
±±3
±53
±±3
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
4.85V to 5.15V
11.40V to 12.60V
11.64V to 12.±6V
11.40V to 12.60V
14.54V to 15.45V
11.40V to 12.60V
2±.28V to 24.72V
11.40V to 12.60V
46.56V to 49.44V
11.40V to 12.60V
4.85V to 5.15V
MPB125-2005
MPB125-2012
MPB125-2015
MPB125-2024
MPB125-2048
15A
5A
0.5A
MPB125-3000
11.40V to 12.60V
-11.64V to -12.±6V
2.42V to 2.58V
10A (NOTE 4,5)
15A (NOTE 4,5)
5A
4.85V to 5.15V
MPB125-4250
(NOTE 1)
11.40V to 12.60V
-11.64V to -12.±6V
±.20V to ±.40V
4.85V to 5.15V
11.40V to 12.60V
-11.64V to -12.±6V
0.5A
10A (NOTE 4,5)
15A (NOTE 4,5)
5A
MPB125-4350
(NOTE 1)
+12V
-12V
0.5A
NOTES: 1) Maximum convection output power is 75 watts.
2) Maximum forced-air output power is 125 watts with 1±0 LFM at 5 CFM.
±) Maximum peak-to-peak noise expressed as a percentage of output voltage, 20 MHz bandwidth.
4) Maximum power of 80 watts from V1 + V2 with 1±0 LFM at 5 CFM forced-air cooling.
5) Maximum power of 45 watts from V1 + V2 for convection cooling.
NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems,
equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc.
TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
REV. 08/23/01
1
MPB125 SERIES
INPUT SPECIFICATIONS
PARAMETER
CONDITIONS/DESCRIPTION
Continuous input range.
AC Input.
Lowest AC input voltage that regulation is maintained with full rated loads.
Over full AC input voltage range at full rated load.
90 VAC at full rated load.
MIN
90
47
90
17
NOM
MAX
264
6±
UNITS
VAC
Hz
VAC
mS
Input Voltage- AC
Input Frequency
Brownout Protection
Hold-up Time
Input Current
1.8
ARMS
Input Protection
Inrush Surge Current
Non-user serviceable internally located AC input line fuse, ±.15A.
Internally limited by thermistor,
one cycle, 25° C.
110VAC:
220VAC:
2±
46
APK
kHz
Power Factor Circuitry
Operating Frequency
Active PFC meets requirements of EN61000-±-2.
Switching frequency of main transformer.
100
OUTPUT SPECIFICATIONS
PARAMETER
CONDITIONS/DESCRIPTION
MIN
75
5
NOM
MAX
UNITS
3
Watts
Efficiency
Full Load, 2±0VAC. Varies with distribution of loads among outputs.
85
Minimum Loads
Ripple and Noise
V1 + V2 + V±.
Full load, 20 MHz bandwidth.
See Model Selection Chart
Output Power
1±0 LFM at 5 CFM forced-air cooling.
Convection, dual and triple-output models.
Convection, four-output models.
125
80
75
Watts
3
Overshoot /Undershoot
Regulation
Output voltage overshoot/undershoot at turn-on.
Varies by output. Total regulation includes: line changes from 85-1±2 VAC
or 170-264 VAC, changes in load starting at 203 load and changing to 1003 load.
10
See Model Selection Chart
Transient Response
Turn-on Delay
Turn-on Rise Time
Maximum deviation due to a 253 load change with unit at 753 load.
Time required for initial output voltage stabilization.
Time required for output voltage to rise from 103 to 903.
±
3
Sec
mS
0.2
0.2
1.5
20
INTERFACE SIGNALS AND INTERNAL PROTECTION
PARAMETER
CONDITIONS/DESCRIPTION
MIN
NOM
MAX
UNITS
Overvoltage Protection
V1 of dual and triple output models; V1 & V2 outputs of 4-output models.
MPB125-4250 (V1)
±.20
±.67
5.74
1±.5
17.0
27.0
50.0
4.0
4.8
7.0
15.5
19.0
±0.7
70.0
MPB125-4±50 (V1)
MPB125-2005, MPB125-±000, MPB125-4X50
MPB125-2012
VDC
MPB125-2015
MPB125-2024
MPB125-2048
Overload Protection
Fully protected against output short circuit. Automatic recovery upon
removal of overload condition.
Remote Sense (Note 1)
Power Good, Delay High
Total voltage compensation for cable losses on +Sense.
Total voltage compensation for cable losses on -Sense.
TTL compatible signal is high if output is within 973 of nominal.
Delay after outputs have reached 973.
200
100
500
mV
mS
100
1.0
Power Good, AC Fail
TTL compatible signal is low if AC power is interrupted for 16 mS. Power
warning before outputs reach 973 of nominal.
mS
NOTES: 1) -Sense must be connected to output common or load common for proper power supply operation.
SAFETY, REGULATORY, AND EMI SPECIFICATIONS
PARAMETER
CONDITIONS/DESCRIPTION
MIN
NOM
MAX
UNITS
Agency Approvals
UL1950.
CSA 22.2 No. 2±4/950.
EN60950 (TÜV).
Approved
Dielectric Withstand Voltage
Electromagnetic Interference
AC to chassis.
Input to output.
EN55022 Conducted.
1500
±000
B
VAC
VDC
Class
2
MPB125 SERIES
SAFETY, REGULATORY, AND EMI SPECIFICATIONS (CONTINUED)
PARAMETER
CONDITIONS/DESCRIPTION
Per EN61000-±-±.
Per EN61000-4-±.
Per EN61000-4-4.
Per EN61000-4-5.
Per EN61000-4-6.
Per EN61000-4-8.
Per EN61000-4-11.
Input to output.
MIN
NOM
MAX
UNITS
Flicker
Radiated Susceptibility
EFT/Burst
Input Transient Protection
RF Immunity
Magnetic Fields
Voltage Dips
Insulation Resistance
Leakage Current
10
M⍀
mA
Per EN60950 (264 VAC)
1.0
ENVIRONMENTAL SPECIFICATIONS
PARAMETER
CONDITIONS/DESCRIPTION
MIN
NOM
MAX
UNITS
Altitude
Operating
Non-Operating
10K
50K
ASL Feet
Operating Temperature
Storage Temperature
Forced-Air Cooling
At 1003 load:
0
-40
50
70
°C
°C
Forced-air cooling of 1±0 LFM at 5 CFM is required for full output power. Air
velocity is measured with power supply mounted on 0.±75" (9.5mm) standoffs.
Airflow direction is from the input section to the output section.
Temperature Coefficient
Relative Humidity
Shock
0°C to 70°C (after 15 minute warm-up).
Non-Condensing.
Operating: 11 ±±mS, ± axes, Half Sine.
±0.02
±0.05
85
15
±0
3/°C
3RH
5
G
Non-operating: 11 ±±mS, ± axes, Half Sine.
Vibration
Operating:
Random vibration, 5-500 Hz, 10 minutes each axis.
2.4
4.8
GRMS
GRMS
Non-Operating: Random vibration, 5-500 Hz, 10 minutes each axis.
3
MPB125 SERIES
J1 - AC I/P CONN.
Pin 1
Pin 2
Pin 3
NEUTRAL
NO PIN
LINE
5.00"
(127.0)
J2 -
MPB125 MPB125 MPB125
Ø 0.16" (4 PL)
(4.06)
4.55"
(115.57)
-3000
-12V
+12V
N/C
-4250
-12V
+12V
+2.5V
+2.5V
+2.5V
RTN
RTN
RTN
RTN
RTN
+5V
-4350
-12V
+12V
+3.3V
+3.3V
+3.3V
RTN
RTN
RTN
RTN
RTN
+5V
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
J1- INPUT
CONNECTOR
N/C
J2 - DC OUTPUT
CONNECTOR
N/C
TOP VIEW
RTN
RTN
RTN
RTN
RTN
+5V
2.56"
(65.02)
3.00"
(76.2)
PIN #1
MPB125-3000
MPB125-4250
MPB125-4350
+5V
+5V
+5V
PIN #1
FASTENER
CLEARANCE
AREA (4 PL)
+5V
+5V
+5V
+5V
+5V
+5V
J3 -
Pin 1
Pin 2
Pin 3
-SENSE
SAFETY GROUND
CONNECTION POINT
PIN #1
J3
0.06"
(1.5)
SCREWS SHOWN
FOR REFERENCE
ONLY
+SENSE
PWR GOOD
1.00"
(25.4)
1.25"
(31.75)
SIDE VIEW
END VIEW
PRINTED CIRCUIT BOARD
0.19"
(4.8)
J2 - DC OUTPUT
CONNECTOR
J2 - DC OUTPUT
CONNECTOR
J2 - DC OUTPUT
CONNECTOR
MPB125-2005
PIN #1
PIN #1
PIN #1
J2 - DC OUTPUT
CONNECTOR
MPB125-2012
MPB125-2015
MPB125-2024
MPB125-2048
PIN #1
PIN #1
PIN #1
J3
PIN #1
J3
J3
PIN #1
J3
MATING CONNECTORS
NOTE: PART NUMBERS ARE MOLEX; EQUIVALENTS ARE ACCEPTABLE.
MPB125
-2005
MPB125
-2012
-2015
MPB125
-2012
-2015
MPB125
-2024
MPB125
-2048
MPB125
-3000
-4250
-4350
J1
J2
J3
Housing
Pins
09-50-8033
08-52-0113
09-50-8103
08-52-0113
22-01-3067
08-50-0114
09-50-8033
08-52-0113
09-50-8063
08-52-0113
22-01-3067
08-50-0114
09-50-8033
08-52-0113
09-50-8063
08-52-0113
22-01-3067
08-50-0114
09-50-8033
08-52-0113
09-50-8043
08-52-0113
22-01-3067
08-50-0114
09-50-8033
08-52-0113
09-50-8023
08-52-0113
22-01-3067
08-50-0114
09-50-8033
08-52-0113
09-50-8143
08-52-0113
22-01-3037
08-50-0114
Housing
Pins
Housing
Pins
4
相关型号：
MPB125-4350G
AC-DC Regulated Power Supply Module, 3 Output, 75W, Hybrid, ROHS COMPLIANT, PACKAGE
BEL
©2020 ICPDF网 联系我们和版权申明