BU1570KN-E2 [ROHM]
AIE: Adaptive Image Enhancer; AIE :自适应图像增强型号: | BU1570KN-E2 |
厂家: | ROHM |
描述: | AIE: Adaptive Image Enhancer |
文件: | 总9页 (文件大小:295K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
AIE Adaptive Image Enhancer Series
AIE:
Adaptive Image Enhancer
(Image processing technology based on ROHM hardware)
BU1570KN, BU1571KN
No.09060EBT01
●Description
BU1570KN/BU1571KN is AIE : Adaptive Image Enhancer (image processing technology by ROHM’s hardware).
Provides unprecedented visibility under severe conditions, such as darkness or extreme backlighting.
●Features
1) UXGA size (16001200) for input of image data up to 7.5 fps, SXGA size (12801024) for input of image data up to
15 fps and VGA size (640480) for input of image data up to 30 fps.
2) Input data format for YUV=4:2:2 8bit. Order of components may be adjusted by the register.
3) Operation modes are image enhance mode, through mode, and sleep mode.
4) Strength of image correction can be set to linear.
5) Able to read out brightness for the entire area for motion detection *1
6) Register can be set up with a 2-line serial interface.
*Extra document is prepared separately about each register setup. Please refer to the Development Scheme on page 6.
*1 : BU1570KN Only
●Application
Security camera, Intercom with camera, Drive recorder, and Web camera etc.
●Lineup
Supply power
source voltage
Interrupt
output
Control
Interface
Output
Interface
Camera
Interface
Parameter
Package
VQFN36
motion
detection
Supported up to
Max 2M pixels.
(1600×1200)
8bit
1.45-1.55(VDDCore)
2.7-3.6(VDDIo)
BU1570KN
I2C BUS
I2C BUS
YUV=4:2:2
Camera interface
Interrupt
output
Supported up to
Max 2M pixels.
(1600×1200)
8bit
1.45-1.55(VDDCore)
2.7-3.6(VDDIo)
BU1571KN
YUV=4:2:2
Camera interface
-
VQFN36
●Absolute maximum ratings (Ta=25℃)
●Recommended operating range
Parameter
Symbol
VDDIO
VDD
VIN
Rating
-0.3~+4.2
-0.3~+2.1
-0.3~VDDIO+0.3
-40~+125
450
Unit
V
Parameter
Symbol
VDDIO
VDD
Rating
Unit
V
Supply power
source voltage 1
Supply power source
voltage 1(IO)
2.70~3.60(Typ:3.3V)
1.45~1.55(Typ:1.50V)
0~VDDIO
Supply power
source voltage 2
Supply power source
voltage 2(CORE)
V
V
V
Input voltage range VIN-VDDIO
V
Input voltage
Storage
temperature range
Operating
Topr
Tstg
℃
mW
-40~+85
℃
temperature range
Power dissipation
PD
*Please supply power source in order of VDD→VDDIO.
*In the case exceeding 25ºC, 4.5mW should be reduced
at the rating 1ºC.
www.rohm.com
2009.04- Rev.B
1/8
© 2009 ROHM Co., Ltd. All rights reserved.
Technical Note
BU1570KN, BU1571KN
●Electric characteristics
(Unless otherwise specified, VDD=1.50V,VDDIO=3.3V,GND=0.0V,Ta=25℃,fIN=52.0MHz)
Limits
TYP.
-
15
-
-
70
-
Parameter
Input frequency
Operating consumption current IDD1
Symbol
Unit
Condition
MIN.
10.0
-
MAX.
52.0
-
30
10
140
10
10
VDDIO
+0.3
VDDIO
0.2
VDDIO
+0.3
VDDIO
0.15
-
fIN
MHz CAMCKI(DUTY45%~55%)
mA
μA
μA
μA
μA
μA
At enhance mode setting
At sleep mode setting, input terminal=GND setting
VIH=VDDIO
Pull-Down terminal, VIH=VDDIO
VIL=GND
Pull-Down terminal, VIL=GND
Static consumption current
Input ”H” current 1
Input ”H” current 2
Input ”L” current 1
IDDst
IIH1
IIH2
IIL1
-
-10
35
-10
-10
VDDIO
0.8
Input ”L” current 2
IIL2
-
Input ”H” voltage 1
Input ”L” voltage 1
Input ”H” voltage 2
VIH1
VIL1
VIH2
-
-
-
V
V
V
Normal input (including input mode of I/O terminal)
Normal input (including input mode of I/O terminal)
Hysteresis input (RESETB, CAMCKI, SDA, SDC)
Hysteresis input (RESETB, CAMCKI, SDA, SDC)
-0.3
VDDIO
0.85
Input ”L” voltage 2
VIL2
Vhys
VOH
-0.3
-
0.5
-
V
V
V
Hysteresis voltage width
Output ”H” voltage
-
Hysteresis input (RESETB, CAMCKI, SDA, SDC)
IOH=-1.0mA(DC)
(including input mode of I/O terminal)
IOL=1.0mA(DC)
VDDIO
-0.4
VDDIO
0.4
Output ”L” voltage
VOL
0.0
-
V
(including input mode of I/O terminal)
●Block Diagram
●Recommended Application Circuit
Motion
Detector
*1
Interrupt
Controller
*2
INT*3
CAMDI[7:0]
8
CAMDO[7:0]
YUV=4:2:2
CAMDO[7:0]
CAMHSO
CAMVSO
CAMCKO
CAMDI[7:0]
YUV=4:2:2
8
Color
Correction
CAMDI[7:0]
CAMHSI
CAMDO[7:0]
CAMHSI
CAMVSI
CAMCKI
Image
Processing
IC
CAMHSO
CAMVSO
Luminance
Distinction
Image
Enhance
BU1570KN
CAMVSI
CAMCKI
Camera
Module
BU1571KN
CAMCKO
SDA
SDC
INT*4
SDA SDC
Serial
Interface
SDA
SDC
CAMHSO
CAMHSI
CAMVSI
Timing
Generator
CAMVSO
CAMCKO
HOST
CPU
CAMCKI
*4 : BU1570KN Only
*1,2,3 : BU1570KN Only
*Extra document is prepared separately about system evaluation. Please refer to the Development Scheme on page 6.
www.rohm.com
2009.04- Rev.B
2/8
© 2009 ROHM Co., Ltd. All rights reserved.
Technical Note
BU1570KN, BU1571KN
●Terminal functions
PIN No.
1
PIN Name
CAMVSI
N.C.
In/Out
In
Active Level
Init
-
Function explanation
I/O type
B*1
*
Vertical Timing Input (pull-down at sleep mode)
2
3
CAMHSI
CAMDI0
CAMDI1
CAMDI2
CAMDI3
CAMDI4
CAMDI5
CAMDI6
CAMDI7
VDDIO
CAMCKI
GND
In
In
*
-
-
B*1
B*1
B*1
B*1
B*1
B*1
B*1
B*1
B*1
-
Horizontal Timing Input (pull-down at sleep mode)
Data Input Bit 0 (pull-down at sleep mode)
Data Input Bit 1 (pull-down at sleep mode)
Data Input Bit 2 (pull-down at sleep mode)
Data Input Bit 3 (pull-down at sleep mode)
Data Input Bit 4 (pull-down at sleep mode)
Data Input Bit 5 (pull-down at sleep mode)
Data Input Bit 6 (pull-down at sleep mode)
Data Input Bit 7 (pull-down at sleep mode)
DIGITAL IO Power Source
4
DATA
DATA
DATA
DATA
DATA
DATA
DATA
DATA
PWR
CLK
5
In
-
6
In
-
7
In
-
8
In
-
9
In
-
10
11
12
13
14
15
16
17
18
19
20
21
In
-
In
-
-
-
In
-
D*1
-
Clock Input (pull-down at sleep mode)
Common GROUND
-
GND
PWR
DATA
CLK
-
VDD
-
-
-
CORE Power Source
SDA
In/Out
In/Out
Out
Out
In
In
-
E
In/Output Serial Data
SDC
E
In/Output Serial Clock
INT*2
*
-
Luminance Changing Interrupt Signal
Vertical Timing Signal Output
CAMVSO
N.C.
-
-
C
CAMHSO
Out
Out
-
-
-
C
C
Horizontal Timing Signal Output
Data Output: Bit 0
22
23
24
25
26
27
28
29
CAMDO0
CAMDO1
CAMDO2
CAMDO3
CAMDO4
CAMDO5
CAMDO6
CAMDO7
DATA
Out
Out
Out
Out
Out
Out
Out
DATA
DATA
DATA
DATA
DATA
DATA
DATA
-
-
-
-
-
-
-
Data Output: Bit 1
Data Output: Bit 2
Data Output: Bit 3
Data Output: Bit 4
Data Output: Bit 5
Data Output: Bit 6
Data Output: Bit 7
C
C
C
C
C
C
C
30
31
32
33
34
35
36
TEST1
TEST2
RESETB
VDDIO
CAMCKO
GND
In
In
In
-
Low
Low
-
-
-
-
-
-
-
B
B
A
-
Test Mode Terminal 1 (Connect to GND)
Test Mode Terminal 2 (Connect to GND)
System Reset Signal
Low
PWR
CLK
GND
PWR
DIGITAL IO Power Source
Clock Output
Out
-
C
-
Common GROUND
VDD
-
-
CORE Power Source
*”*” in the Active Level column indicates that it may be changed during set-up of the register. Init indicates pin status when
released from reset.
*1: Pull-down is ON during reset (initial status).
*2 : In the case of BU1571KN, PIN NAME=TESTOUT.
www.rohm.com
2009.04- Rev.B
3/8
© 2009 ROHM Co., Ltd. All rights reserved.
Technical Note
BU1570KN, BU1571KN
●Equivalent Circuit Structures of input / output pins
Type
The equivalent circuit structure
VDDIO
Type
The equivalent circuit structure
VDDIO
VDDIO
Internal signal
A
B
To internal
To internal
GND
GND
GND
GND
Input terminal with Schmitt
Input terminal with PULL-DOWN
VDDIO
VDDIO
VDDIO
Internal signal
C
D
Internal signal
To internal
GND
Hysteresis input terminal with PULL-DOWN
GND
GND
GND
Output terminal
VDDIO
VDDIO
Internal signal
To
VDDIO
internal
E
Internal signal
Internal signal
GND
GND
GND
Hysteresis input / output terminal
●Terminal Layout
(Bottom View)
VDD
GND
CAMDI6
CAMDI7
VDDIO
CAMCKI
GND
CAMCKO
VDDIO
RESETB
TEST2
VDD
SDA
TEST1
SDC
CAMDO7
INT*1
CAMDO6
*1 : In the case of BU1571KN, PIN NAME=TESTOUT.
www.rohm.com
2009.04- Rev.B
4/8
© 2009 ROHM Co., Ltd. All rights reserved.
Technical Note
BU1570KN, BU1571KN
● Timing Chart
1.
Two-line serial interface
1.1 Two-line serial interface timing
SDA
tSU;DAT
tLOW
tBUF
tHD;ST
SDC
tHD;STA
tSU;STA
tSU;STO
tHD;DAT
tHIGH
Table 1.1-1 I2C Interface timing
Symbol
Parameter
MIN.
TYP.
MAX.
Unit
kHz
fSCL
SDC Clock Frequency
0
-
-
400
-
Hold-time(repetition)『START』conditions
tHD;STA
0.6
us
(The first clock pulse is generated after this period.)
fLOW
The "L" period of SDC clock
1.3
0.6
0.6
0
-
-
-
-
-
-
-
-
-
us
us
us
us
ns
us
tHIGH
The "H" period of SDC clock
tSU;STA
tHD;DAT
tSU;DAT
tSU;STO
Setup time of repetitive 『START』conditions
Hold time of SDA
2.
Setup time of SDA
100
0.6
-
-
Setup time of the 『STOP』conditions
BUS free time between 『STOP』conditions and the 『START』
conditions
tBUF
1.3
-
-
us
Camera module interface
2.1. Camera module interface timing
The input timing of camera image signal on camera I/F is shown in Table 2.1-1.
Table 2.1-1 BU1570KN/BU1571KN timing (Camera data input)
CAMVSI
CAMHSI
CAMDI0
Symbo
MIN
TYP
Explanation
MAX.
UNIT
ns
tCMS
tCMH
CAMCKI Rise / Fall Camera set-up Time
CAMCKI Rise / Fall Camera Hold Time
4
4
-
-
-
-
-CAMDI7
ns
CAMCKI
(CKPOL=“1”)
CAMCKI
(CKPOL=“0”)
tCMH
tCMS
The input timing of camera image signal on camera I/F is shown in Table 2.1-2.
Table 2.1-2
Camera data output timing
tPCLK
MIN
19.
TYP
Symbol
tPCLK
Explanation
MAX.
UNIT
CAMCKO
Clock Cycle
Clock Duty
-
50
-
-
55
5
ns
%
tPHH
tPHL
CAMVSO
CAMHSO
dPCLK
45
-
tPDV
Decision of CAMDO from CAMCKO
ns
ns
tPDV
CAMDO[7:0]
tPHL, tPHH
Decision of CAMVSO or CAMHSO from CAMCKO
-
-
5
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.04- Rev.B
5/8
Technical Note
BU1570KN, BU1571KN
●Development Scheme
This technical note is aimed at trying the connectivity in the hardware between customer’s system and our AIE Adaptive
Image Enhancer series.
We prepare various data and tools for every development STEP as follows other than this technical note, please
contact the sales staff in your duty also including the support system.
(1) Demonstration STEP
(You can try the standard image processing functions by the standard Demonstration kit at once.)
You can confirm on TV screen what carried out AIE processing of a camera image and the DVD video image.
・Standard Demonstration board kit
◎Demonstration board(TV-IN→BU1570KN→TV-OUT board)
◎Demonstration board operation manual
◎Demonstration software
If the software for the trial board is installed in your Windows PC(Windows 2000/XP), more detailed setting is
possible.
◎USB cable
(2) Confirmation STEP
(We will respond to customer’s camera module.)
・Specifications
We will provide specifications for AIE Adaptive Image Enhancer according to customer’s requirements.
・Function explanation
We will deliver you the function explanation describing detailed functions, register settings, external
interfaces, timing, and so forth of AIE Adaptive Image Enhancer according to your requests.
・Application note
We will deliver you the detailed explanation data on application development of AIE Adaptive Image
Enhancer according to your requests.
(3) System check STEP
(You can check the application operation as a system by the kit of system check tools and your camera
module.)
You can check the interface with your camera module and the application operation on the system check board using
the tools for user’s only.
・System check tools kit
◎Board for system evaluation
◎Manual for system evaluation
◎Macro command file for reference
*You can check the detailed functions of the application operation by your PC using the macro command file.
(4) Integrated check STEP with user’s system
(You can check the application operation as a system on your system check board using the integrated
check software.)
You can check the application operation on the sample LSI-equipped system check board by your camera
module using the integrated check software.
・On line Support;We will answer your questions about the software development.
www.rohm.com
2009.04- Rev.B
6/8
© 2009 ROHM Co., Ltd. All rights reserved.
Technical Note
BU1570KN, BU1571KN
Cautions on use
(1)Absolute Maximum Ratings
An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break
down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If any special mode
exceeding the absolute maximum ratings is assumed, consideration should be given to take physical safety measures
including the use of fuses, etc.
(2)Operating conditions
These conditions represent a range within which characteristics can be provided approximately as expected. The electrical
characteristics are guaranteed under the conditions of each parameter.
(3)Reverse connection of power supply connector
The reverse connection of power supply connector can break down ICs. Take protective measures against the breakdown due
to the reverse connection, such as mounting an external diode between the power supply and the IC’s power supply terminal.
(4)Power supply line
Design PCB pattern to provide low impedance for the wiring between the power supply and the GND lines.
In this regard, for the digital block power supply and the analog block power supply, even though these power supplies has the
same level of potential, separate the power supply pattern for the digital block from that for the analog block, thus suppressing
the diffraction of digital noises to the analog block power supply resulting from impedance common to the wiring patterns. For
the GND line, give consideration to design the patterns in a similar manner.
Furthermore, for all power supply terminals to ICs, mount a capacitor between the power supply and the GND terminal. At the
same time, in order to use an electrolytic capacitor, thoroughly check to be sure the characteristics of the capacitor to be used
present no problem including the occurrence of capacity dropout at a low temperature, thus determining the constant.
(5)GND voltage
Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state.
Furthermore, check to be sure no terminals are at a potential lower than the GND voltage including an actual electric transient.
(6)Short circuit between terminals and erroneous mounting
In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting can break
down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between terminals or between the terminal
and the power supply or the GND terminal, the ICs can break down.
(7)Operation in strong electromagnetic field
Be noted that using ICs in the strong electromagnetic field can malfunction them.
(8)Inspection with set PCB
On the inspection with the set PCB, if a capacitor is connected to a low-impedance IC terminal, the IC can suffer stress.
Therefore, be sure to discharge from the set PCB by each process. Furthermore, in order to mount or dismount the set PCB
to/from the jig for the inspection process, be sure to turn OFF the power supply and then mount the set PCB to the jig. After the
completion of the inspection, be sure to turn OFF the power supply and then dismount it from the jig. In addition, for protection
against static electricity, establish a ground for the assembly process and pay thorough attention to the transportation and the
storage of the set PCB.
(9)Input terminals
In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the parasitic
element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of the input terminal.
Therefore, pay thorough attention not to handle the input terminals, such as to apply to the input terminals a voltage lower than
the GND respectively, so that any parasitic element will operate. Furthermore, do not apply a voltage to the input terminals
when no power supply voltage is applied to the IC. In addition, even if the power supply voltage is applied, apply to the input
terminals a voltage lower than the power supply voltage or within the guaranteed value of electrical characteristics.
(10)Ground wiring pattern
If small-signal GND and large-current GND are provided, It will be recommended to separate the large-current GND pattern
from the small-signal GND pattern and establish a single ground at the reference point of the set PCB so that resistance to the
wiring pattern and voltage fluctuations due to a large current will cause no fluctuations in voltages of the small-signal GND. Pay
attention not to cause fluctuations in the GND wiring pattern of external parts as well.
(11)External capacitor
In order to use a ceramic capacitor as the external capacitor, determine the constant with consideration given to a degradation
in the nominal capacitance due to DC bias and changes in the capacitance due to temperature, etc.
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.04- Rev.B
7/8
Technical Note
BU1570KN, BU1571KN
●Order Model Name Selection
2
B U
1 5 7 0
K N
E
Package type
KN:VQFN36
ROHM model name
Product number
Taping model name
E2: Embossed reel tape
●Tape and Reel information
VQFN36
<Tape and Reel information>
<Dimension>
Embossed carrier tape(with dry pack)
Tape
6.2 0.1
(1.1)
6.0 0.1
2500pcs
E2
Quantity
(0.50)
27
19
3
−
(0
.35)
28
18
Direction
of feed
(The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand)
36
10
M
22)
.
(0
1
0.22 0.05
9
0.5
0.05
(0.6−+00..31
)
0.05
Direction of feed
1pin
Reel
(Unit:mm)
※When you order , please order in times the amount of package quantity.
www.rohm.com
2009.04- Rev.B
8/8
© 2009 ROHM Co., Ltd. All rights reserved.
Notice
N o t e s
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, commu-
nication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller,
fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of
any of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
R0039
A
相关型号:
©2020 ICPDF网 联系我们和版权申明