74AVC4T245Q [SGMICRO]
4-Bit Dual-Supply Translating Transceiver with Configurable Voltage Translation and 3-State Outputs;
| 型号： | 74AVC4T245Q |
| 厂家： | 
Shengbang Microelectronics Co, Ltd |
| 描述： | 4-Bit Dual-Supply Translating Transceiver with Configurable Voltage Translation and 3-State Outputs |
| 文件： | 总7页 (文件大小：562K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
74AVC4T245Q
4-Bit Dual-Supply
Translating Transceiver with Configurable
Voltage Translation and 3-State Outputs
GENERAL DESCRIPTION
FEATURES
The 74AVC4T245Q is a 4-bit, dual-supply voltage level
transceiver with 3-state outputs and bidirectional level
translation. The device can be used as two 2-bit
transceivers or one 4-bit transceiver. The nAn and nBn
are four data input-output ports. nDIR are the direction
● AEC-Q100 Qualified for Automotive Applications
Device Temperature Grade 1
TA = -40℃ to +125℃
● VCCA Supply Voltage Range: 0.8V to 3.6V
● VCCB Supply Voltage Range: 0.8V to 3.6V
● Inputs Accept Voltages up to 3.6V
● +12mA/-12mA Output Current
�����
control inputs and nOE are the output enable inputs.
VCCA and VCCB are the supply pins. The supply voltage
of VCCA and VCCB can range from 0.8V to 3.6V, making
the device suitable for bidirectional translating among
any of the 0.8V, 1.2V, 1.5V, 1.8V, 2.5V and 3.3V
● Data Rates:
380Mbps (≥ 1.8V to 3.3V Translation)
200Mbps (≥ 1.1V to 3.3V Translation)
200Mbps (≥ 1.1V to 2.5V Translation)
200Mbps (≥ 1.1V to 1.8V Translation)
150Mbps (≥ 1.1V to 1.5V Translation)
100Mbps (≥ 1.1V to 1.2V Translation)
● Outputs in High-Impedance State when VCCA or
�����
voltage nodes. The nAn, nDIR and nOE signals are
referenced to VCCA and nBn signals are referenced to
VCCB
.
When nDIR is set high, it allows transmission from nAn
to nBn. When nDIR is set low, it allows transmission
VCCB = 0V
�����
from nBn to nAn. nOE can be used to make the
● -40℃ to +125℃ Operating Temperature Range
● Available in a Green TSSOP-16 Package
outputs disabled so that the buses are effectively
isolated. In suspend mode, both nAn and nBn are in
high-impedance state when either VCCA or VCCB input is
at GND level.
APPLICATIONS
This device is highly suitable for partial power-down
applications using power-off leakage current (IOFF) circuit.
When the device is powered down, the current backflow
will be prevented from passing through the device.
Personal Electronic
Industrial Equipment
Enterprise Infrastructures
Telecom Equipment
This device is AEC-Q100 qualified (Automotive
Electronics Council Standard Q100 Grade 1) and the
use of this device is suitable for automotive applications.
SG Micro Corp
SEPTEMBER 2022 – REV. A
www.sg-micro.com
4-Bit Dual-Supply Translating Transceiver with
74AVC4T245Q
Configurable Voltage Translation and 3-State Outputs
PACKAGE/ORDERING INFORMATION
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
TOP
MARKING
MEATS16
XXXXX
PACKAGE
DESCRIPTION
ORDERING
NUMBER
PACKING
OPTION
MODEL
74AVC4T245Q
TSSOP-16
74AVC4T245QTS16G/TR
Tape and Reel, 4000
-40℃ to +125℃
MARKING INFORMATION
NOTE: XXXXX = Date Code, Trace Code and Vendor Code.
X X X X X
Vendor Code
Trace Code
Date Code - Year
Green (RoHS & HSF): SG Micro Corp defines "Green" to mean Pb-Free (RoHS compatible) and free of halogen substances. If
you have additional comments or questions, please contact your SGMICRO representative directly.
ABSOLUTE MAXIMUM RATINGS (1)
OVERSTRESS CAUTION
1. Stresses beyond those listed in Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to
absolute maximum rating conditions for extended periods may
affect reliability. Functional operation of the device at any
conditions beyond those indicated in the Recommended
Operating Conditions sectionis not implied.
Supply Voltage Range, VCCA............................. -0.5V to 4.6V
Supply Voltage Range, VCCB............................. -0.5V to 4.6V
Input Voltage Range, VI (2) ................................ -0.5V to 4.6V
(2)
Output Voltage Range, VO
Suspend or 3-State Mode............................... -0.5V to 4.6V
Active Mode
A Ports..............................-0.5V to MIN (4.6V, VCCA + 0.5V)
B Ports..............................-0.5V to MIN (4.6V, VCCB + 0.5V)
2. The input and output voltage ratings may be exceeded if
the input and output clamp current ratings are observed.
Output Current, IO (VO = 0V to VCC
)
3. The performance capability of a high-performance integrated
circuit in conjunction with its thermal environment can create
junction temperatures which are detrimental to reliability.
High-State or Low-State ..........................................±50mA
Supply Current, ICC, per VCCA or VCCB Pin...................100mA
Ground Current, IGND, per GND Pin ...........................-100mA
Input Clamp Current, IIK (VI < 0)...................................-50mA
Output Clamp Current, IOK (VO < 0)..............................-50mA
Junction Temperature (3) .............................................+150℃
Storage Temperature Range.......................-65℃ to +150℃
Lead Temperature (Soldering, 10s)............................+260℃
ESD Susceptibility
ESD SENSITIVITY CAUTION
This integrated circuit can be damaged if ESD protections are
not considered carefully. SGMICRO recommends that all
integrated circuits be handled with appropriate precautions.
Failureto observe proper handlingand installation procedures
can cause damage. ESD damage can range from subtle
performance degradation tocomplete device failure. Precision
integrated circuits may be more susceptible to damage
because even small parametric changes could cause the
device not to meet the published specifications.
HBM.............................................................................6000V
CDM ............................................................................1000V
RECOMMENDED OPERATING CONDITIONS
Supply Voltage Range, VCCA...............................0.8V to 3.6V
Supply Voltage Range, VCCB...............................0.8V to 3.6V
Input Voltage Range, VI .........................................0V to 3.6V
Output Voltage Range, VO
DISCLAIMER
SG Micro Corp reserves the right to make any change in
circuit design, or specifications without prior notice.
Suspend or 3-State Mode....................................0V to 3.6V
Active Mode
A Ports.................................................................0V to VCCA
B Ports.................................................................0V to VCCB
High-State or Low-State Output Current, IO ................±12mA
Input Transition Rise or Fall Rate, Δt/ΔV
VCCI = 0.8V to 3.6V...........................................5ns/V (MAX)
Operating Temperature Range.....................-40℃ to +125℃
SG Micro Corp
www.sg-micro.com
SEPTEMBER 2022
2
4-Bit Dual-Supply Translating Transceiver with
74AVC4T245Q
Configurable Voltage Translation and 3-State Outputs
LOGIC DIAGRAM
13
1B1
12
11
2B1
10
1B2
2B2
VCCA
VCCB
1OE
15
2OE
14
1DIR
2
2DIR
3
1A1
1A2
2A1
2A2
4
5
6
7
FUNCTION TABLE
SUPPLY VOLTAGE
CONTROL INPUT
INPUT/OUTPUT
(1)
�����
VCCA, VCCB
nDIR
nAn
nBn
nOE
0.8V to 3.6V
0.8V to 3.6V
0.8V to 3.6V
GND (2)
L
L
H
X
X
nAn = nBn
Inputs
L
Inputs
nBn = nAn
H
Z
Z
Z
Z
X
H = High Voltage Level
L = Low Voltage Level
Z = High-Impedance State
X = Don’t Care
NOTES:
�����
1. The nAn, nDIR and nOE signals are referenced to VCCA. The nBn signals are referenced to VCCB
.
2. If at least one of VCCA or VCCB is at GND level, the device enters suspend mode.
SG Micro Corp
www.sg-micro.com
SEPTEMBER 2022
3
4-Bit Dual-Supply Translating Transceiver with
74AVC4T245Q
Configurable Voltage Translation and 3-State Outputs
PIN CONFIGURATION
(TOP VIEW)
VCCA
1DIR
2DIR
1A1
1
2
3
4
5
6
7
8
16 VCCB
1OE
15
2OE
14
1B1
13
12
1A2
2A1
1B2
11
10 2B2
GND
2B1
2A2
GND
9
TSSOP-16
PIN DESCRIPTION
PIN
NAME
FUNCTION
Supply Voltage VCCA. The nAn, nDIR and
1
VCCA
�����
nOE signals are referenced to VCCA
.
2, 3
4, 5
1DIR, 2DIR
1A1, 1A2
2A1, 2A2
GND
Direction Control Inputs.
Data Inputs/Outputs.
Data Inputs/Outputs.
Ground.
6, 7
8, 9
11, 10
13, 12
15, 14
2B1, 2B2
1B1, 1B2
Data Inputs/Outputs.
Data Inputs/Outputs.
Output Enable Inputs (Active Low).
����� �����
1OE, 2OE
Supply Voltage VCCB. The nBn signals are
referenced to VCCB.
16
VCCB
SG Micro Corp
www.sg-micro.com
SEPTEMBER 2022
4
PACKAGE INFORMATION
PACKAGE OUTLINE DIMENSIONS
TSSOP-16
D
E1
E
5.94
1.78
0.42
e
b
0.65
RECOMMENDED LAND PATTERN (Unit: mm)
L
ccc C
A
SEATING PLANE
A2
A1
θ
C
H
c
Dimensions In Millimeters
Symbol
MIN
-
MOD
MAX
1.200
0.150
1.050
0.300
0.200
5.100
4.500
6.600
A
A1
A2
b
-
0.050
0.800
0.190
0.090
4.860
4.300
6.200
-
-
-
c
-
D
-
E
-
E1
e
-
0.650 BSC
L
0.450
0°
-
0.250 TYP
-
0.750
8°
H
θ
ccc
0.100
NOTES:
1. This drawing is subject to change without notice.
2. The dimensions do not include mold flashes, protrusions or gate burrs.
3. Reference JEDEC MO-153.
SG Micro Corp
TX00020.002
www.sg-micro.com
PACKAGE INFORMATION
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
P2
P0
W
Q2
Q4
Q2
Q4
Q2
Q4
Q1
Q3
Q1
Q3
Q1
Q3
B0
Reel Diameter
P1
A0
K0
Reel Width (W1)
DIRECTION OF FEED
NOTE: The picture is only for reference. Please make the object as the standard.
KEY PARAMETER LIST OF TAPE AND REEL
Reel Width
Reel
Diameter
A0
B0
K0
P0
P1
P2
W
Pin1
Package Type
W1
(mm)
(mm) (mm) (mm) (mm) (mm) (mm) (mm) Quadrant
TSSOP-16
13″
12.4
6.80
5.40
1.50
4.0
8.0
2.0
12.0
Q1
SG Micro Corp
TX10000.000
www.sg-micro.com
PACKAGE INFORMATION
CARTON BOX DIMENSIONS
NOTE: The picture is only for reference. Please make the object as the standard.
KEY PARAMETER LIST OF CARTON BOX
Length
(mm)
Width
(mm)
Height
(mm)
Reel Type
Pizza/Carton
13″
386
280
370
5
SG Micro Corp
www.sg-micro.com
TX20000.000
相关型号：
74AVC4T245QRGYRQ1
4-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
TI
74AVC4T245RGYRG4
4-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
TI
74AVC4T245RSVR-NT
Dual-Bit Bus Transceiver with Configurable Voltage Translation and 3-State Outputs
TI
74AVC4T245RSVRG4
4-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
TI
©2020 ICPDF网 联系我们和版权申明