AMC1311 [TI]
2V 输入、精密电压检测增强型隔离式放大器;
| 型号： | AMC1311 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 2V 输入、精密电压检测增强型隔离式放大器 放大器 |
| 文件： | 总38页 (文件大小：1948K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
AMC1311
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
AMC1311x 高阻抗2V 输入增强型隔离放大器
1 特性
3 说明
• 针对隔离式电压测量优化了2V 高阻抗输入电压范
围
• 固定增益：1
• 低直流误差：
AMC1311 是一款隔离式精密放大器，此放大器的输出
与输入电路由抗电磁干扰性能极强的电容隔离层隔开。
该隔离栅经认证可提供高达5kVRMS 的增强型电隔离，
符合 DIN EN IEC 60747-17 (VDE 0884-17) 和
UL1577 标准，并且可支持高达 1500VRMS 的工作电
压。
– AMC1311：
• 失调电压误差：±9.9mV（最大值）
• 温漂±20μV/°C（典型值）
• 增益误差：±1%（最大值）
• 增益漂移：±30ppm/°C（典型值）
– AMC1311B：
该隔离层可将系统中以不同共模电压电平运行的各器件
隔开，防止高电压冲击导致低压侧器件电气损坏或对操
作员造成伤害。
AMC1311 的高阻抗输入针对与高阻抗电阻分压器或任
何其他高阻抗电压信号源的连接进行了优化。出色的直
流精度和低温漂支持在闭环系统中进行精确的隔离式电
压检测和控制。集成的高侧电源电压缺失检测功能可简
化系统级设计和诊断。
• 失调电压误差：±1.5mV（最大值）
• 温漂±10μV/°C（最大值）
• 增益误差：±0.2%（最大值）
• 增益漂移：±40ppm/°C（最大值）
– 非线性度：0.04%（最大值）
• 高侧3.3V 工作电压(AMC1311B)
• 高CMTI：100kV/µs（最小值）(AMC1311B)
• 高侧电源缺失指示
AMC1311 提供两种性能级别选项：AMC1311B 的额定
工业工作温度范围为 –55°C 至 +125°C，AMC1311
为–40°C 至+125°C。
器件信息(1)
• 安全相关认证：
封装尺寸（标称值）
器件型号
AMC1311
AMC1311B
封装
– 符合DIN EN IEC 60747-17 (VDE 0884-17) 标
准的7000VPK 增强型隔离
– 符合UL1577 标准且长达1 分钟的5000VRMS
隔离
SOIC (8)
5.85mm × 7.50mm
(1) 如需了解所有可用封装，请参阅数据表末尾的可订购产品附
录。
– 针对更大工业温度范围进行了全面优化： –
40°C 至+125°C
2 应用
• 可用于以下应用的隔离式电压感应：
– 电机驱动器
– 变频器
– 不间断电源
VDC
High-side supply
(3.3 V or 5 V)
Low-side supply
(3.3 V or 5 V)
R1
AMC1311B
VDD1
IN
VDD2
OUTP
R2
0..2V
RSNS
VCMout
2 V
ADC
SHTDN
GND1
OUTN
GND2
简化版原理图
本文档旨在为方便起见，提供有关TI 产品中文版本的信息，以确认产品的概要。有关适用的官方英文版本的最新信息，请访问
www.ti.com，其内容始终优先。TI 不保证翻译的准确性和有效性。在实际设计之前，请务必参考最新版本的英文版本。
English Data Sheet: SBAS786
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
Table of Contents
8.1 Overview...................................................................20
8.2 Functional Block Diagram.........................................20
8.3 Feature Description...................................................20
8.4 Device Functional Modes..........................................22
9 Application and Implementation..................................23
9.1 Application Information............................................. 23
9.2 Typical Application.................................................... 23
9.3 What To Do and What Not To Do..............................26
10 Power Supply Recommendations..............................27
11 Layout...........................................................................28
11.1 Layout Guidelines................................................... 28
11.2 Layout Example...................................................... 28
12 Device and Documentation Support..........................29
12.1 Documentation Support.......................................... 29
12.2 接收文档更新通知................................................... 29
12.3 支持资源..................................................................29
12.4 Trademarks.............................................................29
12.5 Electrostatic Discharge Caution..............................29
12.6 术语表..................................................................... 29
13 Mechanical, Packaging, and Orderable
1 特性................................................................................... 1
2 应用................................................................................... 1
3 说明................................................................................... 1
4 Revision History.............................................................. 2
5 Device Comparison Table...............................................4
6 Pin Configuration and Functions...................................5
7 Specifications.................................................................. 6
7.1 Absolute Maximum Ratings........................................ 6
7.2 ESD Ratings............................................................... 6
7.3 Recommended Operating Conditions.........................6
7.4 Thermal Information....................................................7
7.5 Power Ratings.............................................................7
7.6 Insulation Specifications ............................................ 8
7.7 Safety-Related Certifications ..................................... 9
7.8 Safety Limiting Values ................................................9
7.9 Electrical Characteristics...........................................10
7.10 Switching Characteristics........................................12
7.11 Timing Diagram.......................................................12
7.12 Insulation Characteristics Curves........................... 13
7.13 Typical Characteristics............................................14
8 Detailed Description......................................................20
Information.................................................................... 29
4 Revision History
注：以前版本的页码可能与当前版本的页码不同
Changes from Revision B (May 2020) to Revision C (June 2022)
Page
• 将隔离标准从DIN VDE V 0884-11 (VDE V 0884-11) 更改为DIN EN IEC 60747-17 (VDE 0884-17)，并相应更
新了绝缘规格和安全相关认证表....................................................................................................................... 1
• 更改了特性部分..................................................................................................................................................1
• Changed pin names: VIN to IN, VOUTP to OUTP, and VOUTN to OUTN......................................................... 5
• Merged VOS specs for 4.5V ≤VDD1 ≤5.5 V and 3.0 V ≤VDD1 ≤5.5 V ranges (AMC1311B only).......... 10
• Changed VDD1 DC PSRR from –65 dB (typical) to –80 dB (typical)............................................................10
• Changed CMTI from 75 kV/µs (minimum), 140 kV/µs (typical) to 100 kV/µs (minimum), 150kV/µs (typical)
(AMC1311B only)..............................................................................................................................................10
• Changed VDD1UV (VDD1 falling) from 1.75 V / 2.53 V / 2.7 V to 2.4 V / 2.6 V / 2.8 V (minimum / typical /
maximum).........................................................................................................................................................10
• Changed Rise, Fall, and Delay Time Definition timing diagram....................................................................... 12
• Changed Reinforced Isolation Capacitor Lifetime Projection figure ................................................................ 13
• Changed functional block diagram................................................................................................................... 20
• Deleted Fail-Safe Output section, added Analog Output section..................................................................... 22
• Changed Typical Application section and subsections.....................................................................................23
• Changed What To Do and What Not To Do section......................................................................................... 26
• Changed Layout section...................................................................................................................................28
Copyright © 2022 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
Changes from Revision A (June 2018) to Revision B (May 2020)
Page
• 将特性部分的AMC1311B 温漂从±15μV/°C（最大值）更改为10μV/°C（最大值） .................................... 1
• 将特性部分的AMC1311B 增益误差从±0.3%（最大值）更改为±0.2%（最大值），并将AMC1311B 增益漂
移从±45ppm/°C（最大值）更改为±40ppm/°C（最大值） ...............................................................................1
• 将IEC 60950-1 和IEC60065 更改为IEC 62368-1 ........................................................................................... 1
• Changed AMC1311B values for TCVOS, EG, and TCEG in Device Comparison Table ......................................4
• Changed AMC1311B values for TCVOS, EG, and TCEG in Device Comparison Table ......................................6
• Added ESD classification levels to ESD Ratings table.......................................................................................6
• Changed CLR and CPG values from 9 mm to 8.5 mm.......................................................................................6
• Changed Insulation Specifications table per ISO standard................................................................................ 6
• Changed Safety-Related Certification table per ISO standard........................................................................... 6
• Changed Safety Limiting Values description as per ISO standard..................................................................... 6
• Changed TCVOS parameter minimum value from –15 μV/°C to –10 μV/°C and maximum value from 15
μV/°C to 10μV/°C for the AMC1311B in the Electrical Characteristics table................................................... 6
• Changed EG parameter minimum value from –0.3% to –0.2% and maximum value from 0.3% to 0.2% for
the AMC1311B in the Electrical Characteristics table.........................................................................................6
• Changed TCEG parameter minimum value from –45 ppm/°C to –40 ppm/°C and maximum value from 45
ppm/°C to 40 ppm/°C for the AMC1311B in the Electrical Characteristics table................................................ 6
• Changed Step Response of the AMC1311 figure.............................................................................................26
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
5 Device Comparison Table
PARAMETER
High-side supply voltage, VDD1
AMC1311B
3.0 V to 5.5 V
AMC1311
4.5 V to 5.5 V
–40°C to +125°C
±9.9 mV
Specified ambient temperature, TA
–55°C to +125°C
±1.5 mV
4.5 V ≤VDD1 ≤5.5 V
3.0 V ≤VDD1 ≤5.5 V
Input offset voltage, VOS
±2.5 mV
Not applicable
±20 µV/°C (typ)
±1%
Input offset drift, TCVOS
Gain error, EG
±3 µV/°C (typ), ±10 µV/°C (max)
±0.2%
Gain error drift, TCEG
±5 ppm/°C (typ), ±40 ppm/°C (max)
100 kV/µs (min)
±30 ppm/°C (typ)
15 kV/µs (min)
Common-mode transient immunity, CMTI
Copyright © 2022 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
6 Pin Configuration and Functions
VDD1
IN
1
2
3
4
8
7
6
5
VDD2
OUTP
OUTN
GND2
SHTDN
GND1
Not to scale
图6-1. DWV Package, 8-Pin SOIC (Top View)
表6-1. Pin Functions
PIN
NAME
TYPE
DESCRIPTION
NO.
1
2
3
4
5
6
7
8
VDD1
IN
High-side power
Analog input
High-side power supply(1)
Analog input
SHTDN
GND1
GND2
OUTN
OUTP
VDD2
Digital input
Shutdown input, active high, with internal pullup resistor (typical value: 100 kΩ)
High-side analog ground
High-side ground
Low-side ground
Analog output
Analog output
Low-side power
Low-side analog ground
Inverting analog output
Noninverting analog output
Low-side power supply(1)
(1) See the Power Supply Recommendations section for power-supply decoupling recommendations.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
7 Specifications
7.1 Absolute Maximum Ratings
see(1)
MIN
–0.3
MAX
UNIT
High-side VDD1 to GND1
6.5
6.5
Power-supply voltage
Input voltage
V
Low-side VDD2 to GND2
–0.3
IN
VDD1 + 0.5
VDD1 + 0.5
VDD2 + 0.5
10
GND1 –6
GND1 –0.5
GND2 –0.5
–10
V
SHTDN
Output voltage
Input current
OUTP, OUTN
V
Continuous, any pin except power-supply pins
mA
Junction, TJ
Storage, Tstg
150
Temperature
°C
150
–65
(1) Operation outside the Absolute Maximum Ratings may cause permanent device damage. Absolute Maximum Ratings do not imply
functional operation of the device at these or any other conditions beyond those listed under Recommended Operating Conditions. If
used outside the Recommended Operating Conditions but within the Absolute Maximum Ratings, the device may not be fully
functional, and this may affect device reliability, functionality, performance, and shorten the device lifetime.
7.2 ESD Ratings
VALUE
±2000
±1000
UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
Charged-device model (CDM), per ANSI/ESDA/JEDEC JS-002(2)
V(ESD)
Electrostatic discharge
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
over operating ambient temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
POWER SUPPLY
High-side power supply
VDD1 to GND1, AMC1311
VDD1 to GND1, AMC1311B
VDD2 to GND2
4.5
3
5
5
5.5
5.5
5.5
V
V
Low-side power supply
ANALOG INPUT
3
3.3
VClipping
VFSR
Input voltage before clipping output
Specified linear full-scale voltage
IN to GND1
IN to GND1
2.516
V
V
2
–0.1
ANALOG OUTPUT
On OUTP or OUTN to GND2
OUTP to OUTN
500
250
1
CLOAD Capacitive load
pF
RLOAD
DIGITAL INPUT
Input voltage
TEMPERATURE RANGE
Resistive load
On OUTP or OUTN to GND2
10
kΩ
SHTDN to GND1
0
VDD1
V
AMC1311
125
125
–40
–55
TA
Specified ambient temperature
°C
AMC1311B
Copyright © 2022 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
7.4 Thermal Information
DWV (SOIC)
UNIT
THERMAL METRIC(1)
8 PINS
RθJA
Junction-to-ambient thermal resistance
84.6
28.3
41.1
4.9
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top) Junction-to-case (top) thermal resistance
RθJB
ΨJT
Junction-to-board thermal resistance
Junction-to-top characterization parameter
Junction-to-board characterization parameter
39.1
n/a
ΨJB
RθJC(bot) Junction-to-case (bottom) thermal resistance
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
7.5 Power Ratings
PARAMETER
TEST CONDITIONS
VDD1 = VDD2 = 5.5 V
VALUE
98
UNIT
PD
Maximum power dissipation (both sides)
mW
VDD1 = VDD2 = 3.6V, AMC1311B only
VDD1 = 5.5 V
56
53
PD1
Maximum power dissipation (high-side)
Maximum power dissipation (low-side)
mW
mW
VDD1 = 3.6 V, AMC1311B only
VDD2 = 5.5 V
30
45
PD2
VDD2 = 3.6 V, AMC1311B only
26
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
UNIT
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
7.6 Insulation Specifications
over operating ambient temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VALUE
GENERAL
CLR
External clearance(1)
External creepage(1)
Shortest pin-to-pin distance through air
mm
mm
≥8.5
≥8.5
CPG
Shortest pin-to-pin distance across the package surface
Minimum internal gap (internal clearance) of the double
insulation
DTI
CTI
Distance through insulation
mm
V
≥0.021
Comparative tracking index
Material group
DIN EN 60112 (VDE 0303-11); IEC 60112
According to IEC 60664-1
≥600
I
I-IV
I-III
Rated mains voltage ≤600 VRMS
Rated mains voltage ≤1000 VRMS
Overvoltage category
per IEC 60664-1
DIN EN IEC 60747-17 (VDE 0884-17)(2)
Maximum repetitive peak
VIORM
At AC voltage
2120
VPK
isolation voltage
At AC voltage (sine wave)
1500
2120
7000
8400
9800
VRMS
VDC
Maximum-rated isolation
VIOWM
working voltage
At DC voltage
VTEST = VIOTM, t = 60 s (qualification test)
VTEST = 1.2 × VIOTM, t = 1 s (100% production test)
Tested in air, 1.2/50-µs waveform per IEC 62368-1
Maximum transient
VIOTM
VPK
isolation voltage
VIMP
Maximum impulse voltage(3)
VPK
VPK
Maximum surge
Tested in oil (qualification test),
1.2/50-µs waveform per IEC 62368-1
VIOSM
12800
≤5
isolation voltage(4)
Method a, after input/output safety test subgroups 2 and 3,
Vini = VIOTM, tini = 60 s, Vpd(m) = 1.2 × VIORM, tm = 10 s
Method a, after environmental tests subgroup 1,
Vini = VIOTM, tini = 60 s, Vpd(m) = 1.6 × VIORM, tm = 10 s
≤5
qpd
Apparent charge(5)
pC
Method b1, at routine test (100% production) and
preconditioning (type test), Vini = VIOTM, tini = 1 s, Vpd(m) = 1.875
× VIORM, tm = 1 s
≤5
Barrier capacitance,
input to output(6)
CIO
RIO
VIO = 0.5 VPP at 1 MHz
~1.5
pF
VIO = 500 V at TA = 25°C
> 1012
> 1011
> 109
Insulation resistance,
input to output(6)
VIO = 500 V at 100°C ≤TA ≤125°C
VIO = 500 V at TS = 150°C
Ω
Pollution degree
Climatic category
2
55/125/21
UL1577
VTEST = VISO = 5000 VRMS, t = 60 s (qualification),
VTEST = 1.2 × VISO = 6000 VRMS, t = 1 s (100% production test)
VISO
Withstand isolation voltage
5000
VRMS
(1) Apply creepage and clearance requirements according to the specific equipment isolation standards of an application. Care must be
taken to maintain the creepage and clearance distance of a board design to ensure that the mounting pads of the isolator on the
printed circuit board (PCB) do not reduce this distance. Creepage and clearance on a PCB become equal in certain cases. Techniques
such as inserting grooves, ribs, or both on a PCB are used to help increase these specifications.
(2) This coupler is suitable for safe electrical insulation only within the safety ratings. Compliance with the safety ratings shall be ensured
by means of suitable protective circuits.
(3) Testing is carried out in air to determine the surge immunity of the package.
(4) Testing is carried in oil to determine the intrinsic surge immunity of the isolation barrier.
(5) Apparent charge is electrical discharge caused by a partial discharge (pd).
(6) All pins on each side of the barrier are tied together, creating a two-pin device.
Copyright © 2022 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
7.7 Safety-Related Certifications
VDE
UL
DIN EN IEC 60747-17 (VDE 0884-17),
EN IEC 60747-17,
DIN EN IEC 62368-1 (VDE 0868-1),
EN IEC 62368-1,
Recognized under 1577 component recognition
IEC 62368-1 Clause : 5.4.3 ; 5.4.4.4 ; 5.4.9
Reinforced insulation
Single protection
Certificate number: 40040142
File number: E181974
7.8 Safety Limiting Values
Safety limiting(1) intends to minimize potential damage to the isolation barrier upon failure of input or output circuitry. A failure
of the I/O can allow low resistance to ground or the supply and, without current limiting, dissipate sufficient power to over-
heat the die and damage the isolation barrier potentially leading to secondary system failures.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
R
θJA = 84.6°C/W, VDDx = 5.5 V,
268
TJ = 150°C, TA = 25°C
θJA = 84.6°C/W, VDDx = 3.6 V,
TJ = 150°C, TA = 25°C, AMC1311B only
θJA = 84.6°C/W, TJ = 150°C, TA = 25°C
IS
Safety input, output, or supply current
mA
R
410
PS
TS
Safety input, output, or total power
Maximum safety temperature
R
1477
150
mW
°C
(1) The maximum safety temperature, TS, has the same value as the maximum junction temperature, TJ, specified for the device. The IS
and PS parameters represent the safety current and safety power, respectively. Do not exceed the maximum limits of IS and PS. These
limits vary with the ambient temperature, TA.
The junction-to-air thermal resistance, RθJA, in the Thermal Information table is that of a device installed on a high-K test board for
leaded surface-mount packages. Use these equations to calculate the value for each parameter:
TJ = TA + RθJA × P, where P is the power dissipated in the device.
TJ(max) = TS = TA + RθJA × PS, where TJ(max) is the maximum junction temperature.
PS = IS × VDDmax, where VDDmax is the maximum supply voltage for high-side and low-side.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
7.9 Electrical Characteristics
minimum and maximum specifications of the AMC1311 apply from TA = –40°C to +125°C, VDD1 = 4.5 V to 5.5 V, VDD2 =
3.0 V to 5.5 V, VIN = –0.1 V to 2 V, and SHTDN = GND1 = 0 V; minimum and maximum specifications of the AMC1311B
apply from TA = –55°C to +125°C, VDD1 = 3.0 V to 5.5 V, VDD2 = 3.0 V to 5.5 V, VIN = –0.1 V to 2 V, and SHTDN = GND1
= 0 V (unless otherwise noted); typical specifications are at TA = 25°C, VDD1 = 5 V, and VDD2 = 3.3 V
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
ANALOG INPUT
TA = 25°C, 4.5 V ≤VDD1 ≤5.5 V,
AMC1311
±0.4
9.9
mV
–9.9
–1.5
VOS
Input offset voltage(1) (2)
TA = 25°C, AMC1311B(3)
AMC1311
±0.4
±20
±3
1
1.5
TCVOS
Input offset thermal drift(1) (2) (5)
µV/°C
10
AMC1311B
–10
–15
RIN
IIB
Input resistance
Input bias current
Input capacitance
TA = 25℃
GΩ
3.5
7
15
nA
pF
IN = GND1, TA = 25℃
fIN = 275 kHz
CIN
ANALOG OUTPUT
Nominal gain
1
0.4%
V/V
1%
TA = 25℃, AMC1311
TA = 25℃, AMC1311B
AMC1311
–1%
EG
Gain error(1)
±0.05%
±30
0.2%
–0.2%
TCEG
Gain error drift(1) (6)
ppm/°C
dB
AMC1311B
±5
40
–40
Nonlineartity(1)
±0.01%
0.04%
–0.04%
VIN = 2 VPP, VIN > 0 V,
fIN = 10 kHz, BW = 10 kHz
THD
SNR
Total harmonic distortion(4)
–87
VIN = 2 VPP, fIN = 1 kHz, BW = 10 kHz
VIN = 2 VPP, fIN = 10 kHz, BW = 100 kHz
VIN = GND1, BW = 100 kHz
vs VDD1, at DC
79
82.6
70.9
220
Signal-to-noise ratio
Output noise
dB
µVrms
–80
–85
–65
–70
1.44
vs VDD2, at DC
PSRR
Power-supply rejection ratio(2)
dB
vs VDD1, 10 kHz / 100-mV ripple
vs VDD2, 10 kHz / 100-mV ripple
VCMout
Output common-mode voltage
1.39
1.49
V
V
VOUT = (VOUTP –VOUTN);
VIN > VClipping
VCLIPout
Clipping differential output voltage
2.49
SHTDN = high, or VDD1 undervoltage,
or VDD1 missing
VFAILSAFE Failsafe differential output voltage
V
–2.6
–2.5
AMC1311
100
220
220
275
BW
Output bandwidth
Output resistance
kHz
Ω
AMC1311B
ROUT
On OUTP or OUTN
<0.2
On OUTP or OUTN, sourcing or sinking,
IN = GND1, outputs shorted to
either GND or VDD2
Output short-circuit current
14
mA
AMC1311
15
30
CMTI
Common-mode transient immunity
kV/µs
AMC1311B
100
150
Copyright © 2022 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
7.9 Electrical Characteristics (continued)
minimum and maximum specifications of the AMC1311 apply from TA = –40°C to +125°C, VDD1 = 4.5 V to 5.5 V, VDD2 =
3.0 V to 5.5 V, VIN = –0.1 V to 2 V, and SHTDN = GND1 = 0 V; minimum and maximum specifications of the AMC1311B
apply from TA = –55°C to +125°C, VDD1 = 3.0 V to 5.5 V, VDD2 = 3.0 V to 5.5 V, VIN = –0.1 V to 2 V, and SHTDN = GND1
= 0 V (unless otherwise noted); typical specifications are at TA = 25°C, VDD1 = 5 V, and VDD2 = 3.3 V
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
DIGITAL INPUT
IIN
Input current
1
µA
pF
SHTDN pin, GND1 ≤SHTDN ≤VDD1
–70
CIN
Input capacitance
SHTDN pin
5
0.7 ×
VDD1
VIH
VIL
High-level input voltage
V
V
0.3 ×
VDD1
Low-level input voltage
POWER SUPPLY
VDD1 rising
VDD1 falling
VDD2 rising
VDD2 falling
2.5
2.4
2.7
2.6
2.9
2.8
VDD1 undervoltage detection
threshold
VDD1UV
VDD2UV
V
V
2.2
2.45
2.0
2.65
2.2
VDD2 undervoltage detection
threshold
1.85
3.0 V < VDD1 < 3.6 V, SHTDN = low,
AMC1311B only
6.0
8.4
9.7
mA
IDD1
High-side supply current
Low-side supply current
4.5 V < VDD1 < 5.5 V, SHTDN = low
SHTDN = VDD1
7.1
1.3
5.3
5.9
µA
3.0 V < VDD2 < 3.6 V
7.2
8.1
IDD2
mA
4.5 V < VDD2 < 5.5 V
(1) The typical value includes one standard deviation (sigma) at nominal operating conditions.
(2) This parameter is input referred.
(3) The typical value is at VDD1 = 3.3 V.
(4) THD is the ratio of the rms sum of the amplitudes of first five higher harmonics to the amplitude of the fundamental.
(5) Offset error temperature drift is calculated using the box method, as described by the following equation:
TCVOS = (ValueMAX - ValueMIN) / TempRange
(6) Gain error temperature drift is calculated using the box method, as described by the following equation:
TCEG (ppm) = (ValueMAX - ValueMIN) / (Value(T=25℃) x TempRange) x 106
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
7.10 Switching Characteristics
over operating ambient temperature range (unless otherwise noted)
PARAMETER
Output signal rise time
Output signal fall time
TEST CONDITIONS
MIN
TYP
1.3
1.3
1.5
1.0
2.1
1.6
3.0
2.5
MAX
UNIT
µs
tr
tf
µs
Unfiltered output, AMC1311
Unfiltered output, AMC1311B
Unfiltered output, AMC1311
Unfiltered output, AMC1311B
Unfiltered output, AMC1311
Unfiltered output, AMC1311B
2.5
1.5
3.1
2.1
4.0
3.0
µs
µs
IN to OUTx signal delay (50% –10%)
IN to OUTx signal delay (50% –50%)
µs
µs
IN to OUTx signal delay (50% –90%)
VDD1 step to 3.0 V with VDD2 ≥3.0 V,
to VOUTP, VOUTN valid, 0.1% settling
tAS
Analog settling time
50
100
tEN
Device enable time
SHTDN high to low
SHTDN low to high
50
3
100
10
µs
µs
tSHTDN
Device shutdown time
7.11 Timing Diagram
2 V
IN
0 V
tf
tr
OUTN
OUTP
VCMout
50% - 10%
50% - 50%
50% - 90%
图7-1. Rise, Fall, and Delay Time Definition
Copyright © 2022 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
7.12 Insulation Characteristics Curves
500
1600
1400
1200
1000
800
600
400
200
0
AVDD = DVDD = 3.6 V, AMC1311B
AVDD = DVDD = 5.5 V
400
300
200
100
0
0
50
100
TA (°C)
150
200
0
50
100
TA (èC)
150
200
D001
D002
图7-2. Thermal Derating Curve for Safety-Limiting 图7-3. Thermal Derating Curve for Safety-Limiting
Current per VDE Power per VDE
1.E+11
Safety Margin Zone: 1800 VRMS, 254 Years
Operating Zone: 1500 VRMS, 135 Years
TDDB Line (<1 PPM Fail Rate)
1.E+10
1.E+9
1.E+8
1.E+7
1.E+6
1.E+5
1.E+4
1.E+3
1.E+2
1.E+1
87.5%
20%
500 1500 2500 3500 4500 5500 6500 7500 8500 9500
Stress Voltage (VRMS
)
TA up to 150°C, stress-voltage frequency = 60 Hz, isolation working voltage = 1500 VRMS, operating lifetime = 135 years
图7-4. Reinforced Isolation Capacitor Lifetime Projection
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
7.13 Typical Characteristics
at VDD1 = 5 V, VDD2 = 3.3 V, SHTDN = 0 V, fIN = 10 kHz, and BW = 100 kHz (unless otherwise noted)
2.5
2
10
8
vs VDD1
vs VDD2
1.5
1
6
4
0.5
0
2
0
-0.5
-1
-2
-4
-6
-8
-10
-1.5
-2
Device 1
Device 2
Device 3
-2.5
3
3.25 3.5 3.75
4
4.25 4.5 4.75
VDDx (V)
5
5.25 5.5
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
D005
D019
3.0 V ≤VDD1 < 4.5 V for the AMC1311B only
图7-5. Input Offset Voltage vs Supply Voltage
AMC1311
图7-6. Input Offset Voltage vs Temperature
1.5
1
2.5
2
Device 1
Device 2
Device 3
1.5
1
0.5
0
0.5
0
-0.5
-1
-0.5
-1
-1.5
-2
Device 1
Device 2
Device 3
-1.5
-2.5
-55 -40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
-55 -40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
D006
D007
VDD1 = 5 V, AMC1311B
VDD1 = 3.3 V, AMC1311B
图7-7. Input Offset Voltage vs Temperature
图7-8. Input Offset Voltage vs Temperature
14
12
10
8
15
12
9
6
3
0
6
-3
-6
-9
-12
-15
4
2
0
3
3.25 3.5 3.75
4
4.25 4.5 4.75
VDD1 (V)
5
5.25 5.5
100
1000
fIN (kHz)
10000
D010
D009
3.0 V ≤VDD1 < 4.5 V for the AMC1311B only
图7-9. Input Capacitance vs Input Signal Frequency
图7-10. Input Bias Current vs High-Side Supply Voltage
Copyright © 2022 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
7.13 Typical Characteristics (continued)
at VDD1 = 5 V, VDD2 = 3.3 V, SHTDN = 0 V, fIN = 10 kHz, and BW = 100 kHz (unless otherwise noted)
15
12
9
1
0.8
0.6
0.4
0.2
0
6
3
0
-0.2
-0.4
-0.6
-0.8
-1
-3
-6
-9
-12
-15
AMC1311 vs VDD1
AMC1311 vs VDD2
AMC1311B vs VDD1
AMC1311B vs VDD2
3
3.25 3.5 3.75
4
4.25 4.5 4.75
VDDx (V)
5
5.25 5.5
-55 -40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
D014
D011
3.0 V ≤VDD1 < 4.5 V for the AMC1311B only
图7-12. Gain Error vs Supply Voltage
–55°C ≤TA < –40°C for the AMC1311B only
图7-11. Input Bias Current vs Temperature
1
0.3
0.2
0.1
0
Device 1
Device 2
Device 3
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
-0.1
-0.2
-0.3
Device 1
Device 2
Device 3
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
-55 -40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
D015
D016
AMC1311
AMC1311B
图7-13. Gain Error vs Temperature
图7-14. Gain Error vs Temperature
5
0
50
0
-5
-50
-10
-15
-20
-25
-30
-35
-40
-100
-150
-200
-250
-300
-350
-400
AMC1311B
AMC1311
AMC1311B
AMC1311
1
10
100
1000
0.01
0.1
1
10
100
1000
fIN (kHz)
fIN (kHz)
D04034
D044
图7-15. Normalized Gain vs Input Frequency
图7-16. Output Phase vs Input Frequency
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
7.13 Typical Characteristics (continued)
at VDD1 = 5 V, VDD2 = 3.3 V, SHTDN = 0 V, fIN = 10 kHz, and BW = 100 kHz (unless otherwise noted)
0.04
0.03
0.02
0.01
0
5
4.5
4
VOUTP
VOUTN
3.5
3
2.5
2
-0.01
-0.02
-0.03
-0.04
1.5
1
0.5
0
-0.2
0
0.2 0.4 0.6 0.8 1
VIN (V)
1.2 1.4 1.6 1.8
2
-0.1
0.3
0.7
1.1
1.5
1.9
2.3
2.7
D020
VIN (V)
D018
图7-18. Nonlinearity vs Input Voltage
图7-17. Output Voltage vs Input Voltage
0.04
0.03
0.02
0.01
0
0.04
0.03
0.02
0.01
0
vs VDD1
vs VDD2
-0.01
-0.02
-0.03
-0.04
-0.01
-0.02
-0.03
-0.04
Device 1
Device 2
Device 3
-55 -40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
3
3.25 3.5 3.75
4
4.25 4.5 4.75
VDDx (V)
5
5.25 5.5
D022
D021
–55°C ≤TA < –40°C for the AMC1311B only
图7-20. Nonlinearity vs Temperature
3.0 V ≤VDD1 < 4.5 V for the AMC1311B only
图7-19. Nonlinearity vs Supply Voltage
-70
-75
-70
-75
vs VDD1
vs VDD2
-80
-80
-85
-85
-90
-90
Device 1
Device 2
Device 3
-95
-95
-100
-100
3
3.25 3.5 3.75
4
4.25 4.5 4.75
VDDx (V)
5
5.25 5.5
-55 -40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
D023
D024
3.0 V ≤VDD1 < 4.5 V for the AMC1311B only
–55°C ≤TA < –40°C for the AMC1311B only
图7-21. Total Harmonic Distortion vs Supply Voltage
图7-22. Total Harmonic Distortion vs Temperature
Copyright © 2022 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
7.13 Typical Characteristics (continued)
at VDD1 = 5 V, VDD2 = 3.3 V, SHTDN = 0 V, fIN = 10 kHz, and BW = 100 kHz (unless otherwise noted)
1000
100
10
72.5
70
67.5
65
62.5
60
57.5
55
52.5
50
1
47.5
45
0.1
42.5
0.1
1
10
Frequency (kHz)
100
1000
0
0.2 0.4 0.6 0.8
1
VIN (V)
1.2 1.4 1.6 1.8
2
D025
D026
图7-23. Input-Referred Noise Density vs Frequency
图7-24. Signal-to-Noise Ratio vs Input Voltage
80
80
vs VDD1
vs VDD2
77.5
75
77.5
75
72.5
70
72.5
70
67.5
65
67.5
65
Device 1
Device 2
Device 3
62.5
60
62.5
60
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
3
3.25 3.5 3.75
4
4.25 4.5 4.75
VDDx (V)
5
5.25 5.5
D028
D027
–55°C ≤TA < –40°C for the AMC1311B only
图7-26. Signal-to-Noise Ratio vs Temperature
3.0 V ≤VDD1 < 4.5 V for the AMC1311B only
图7-25. Signal-to-Noise Ratio vs Supply Voltage
0
1.49
1.48
1.47
1.46
1.45
1.44
1.43
1.42
1.41
1.4
-20
-40
-60
-80
-100
-120
VDD1
VDD2
1.39
0.1
1
10
Ripple Frequency (kHz)
100
1000
3
3.25 3.5 3.75
4
4.25 4.5 4.75
VDD2 (V)
5
5.25 5.5
D029
D031
100-mV ripple
图7-27. Power-Supply Rejection Ratio vs Ripple Frequency
图7-28. Output Common-Mode Voltage vs Low-Side Supply
Voltage
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
7.13 Typical Characteristics (continued)
at VDD1 = 5 V, VDD2 = 3.3 V, SHTDN = 0 V, fIN = 10 kHz, and BW = 100 kHz (unless otherwise noted)
300
290
280
270
260
250
240
230
220
210
200
1.49
1.48
1.47
1.46
1.45
1.44
1.43
1.42
1.41
1.4
AMC1311B
AMC1311
1.39
3
3.25 3.5 3.75
4
4.25 4.5 4.75
VDD2 (V)
5
5.25 5.5
-55 -40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
D033
D032
–55°C ≤TA < –40°C for the AMC1311B only
图7-30. Output Bandwidth vs Low-Side Supply Voltage
图7-29. Output Common-Mode Voltage vs Temperature
300
8.5
8
AMC1311B
AMC1311
290
280
270
260
250
240
230
220
210
200
7.5
7
6.5
6
5.5
5
4.5
IDD1 vs VDD1
IDD2 vs VDD2
4
3.5
-55 -40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
3
3.25 3.5 3.75
4
4.25 4.5 4.75
VDDx (V)
5
5.25 5.5
D034
D035
3.0 V ≤VDD1 < 4.5 V for the AMC1311B only
图7-32. Supply Current vs Supply Voltage
图7-31. Output Bandwidth vs Temperature
8.5
8
4
3.5
3
7.5
7
2.5
2
6.5
6
5.5
5
1.5
1
4.5
4
0.5
0
IDD1
IDD2
3.5
-55 -40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
3
3.25 3.5 3.75
4
4.25 4.5 4.75
VDD2 (V)
5
5.25 5.5
D036
D037
–55°C ≤TA < –40°C for the AMC1311B only
图7-33. Supply Current vs Temperature
图7-34. Output Rise and Fall Time vs Low-Side Supply Voltage
Copyright © 2022 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
7.13 Typical Characteristics (continued)
at VDD1 = 5 V, VDD2 = 3.3 V, SHTDN = 0 V, fIN = 10 kHz, and BW = 100 kHz (unless otherwise noted)
4
3.5
3
3.8
3.4
3
2.6
2.2
1.8
1.4
1
2.5
2
1.5
1
50% - 90%
50% - 50%
50% - 10%
0.5
0
0.6
0.2
-55 -40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
3
3.25 3.5 3.75
4
4.25 4.5 4.75
VDD2 (V)
5
5.25 5.5
D038
D039
AMC1311
–55°C ≤TA < –40°C for the AMC1311B only
图7-35. Output Rise and Fall Time vs Temperature
图7-36. IN to OUTP, OUTN Signal Delay vs Low-Side Supply
Voltage
3.8
3.8
3.4
3
50% - 90%
50% - 50%
50% - 10%
3.4
3
2.6
2.2
1.8
1.4
1
2.6
2.2
1.8
1.4
1
50% - 90%
50% - 50%
50% - 10%
0.6
0.2
0.6
0.2
-40 -25 -10
3
3.25 3.5 3.75
4
4.25 4.5 4.75
VDD2 (V)
5
5.25 5.5
5
20 35 50 65 80 95 110 125
Temperature (°C)
D040
D041
AMC1311B
AMC1311
图7-37. IN to OUTP, OUTN Signal Delay vs Low-Side Supply
图7-38. IN to OUTP, OUTN Signal Delay vs Temperature
Voltage
3.8
3.4
3
50% - 90%
50% - 50%
50% - 10%
2.6
2.2
1.8
1.4
1
0.6
0.2
-55 -40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (°C)
D042
AMC1311B
图7-39. IN to OUTP, OUTN Signal Delay vs Temperature
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
8 Detailed Description
8.1 Overview
The AMC1311 is a precision, single-ended input, isolated amplifier with a high input impedance and wide input
voltage range. The input stage of the device drives a second-order, delta-sigma (ΔΣ) modulator. The modulator
converts the analog input signal into a digital bitstream that is transferred across the isolation barrier and
separates the high-side from the low-side. On the low-side, the received bitstream is processed by a fourth-order
analog filter that outputs a differential signal at the OUTP and OUTN pins proportional to the input signal.
The SiO2-based, capacitive isolation barrier supports a high level of magnetic field immunity, as described in the
ISO72x Digital Isolator Magnetic-Field Immunity application report. The digital modulation used in the AMC1311
to transmit data across the isolation barrier, and the isolation barrier characteristics itself, result in high reliability
and high common-mode transient immunity.
8.2 Functional Block Diagram
VDD1
VDD2
OUTP
OUTN
GND2
AMC1311B
Analog Filter
IN
ΔΣ Modulator
SHTDN
GND1
8.3 Feature Description
8.3.1 Analog Input
The single-ended, high-impedance input stage of the AMC1311 feeds a second-order, switched-capacitor, feed-
forward ΔΣ modulator. The modulator converts the analog signal into a bitstream that is transferred across the
isolation barrier, as described in the Isolation Channel Signal Transmission section.
There are two restrictions on the analog input signal IN. First, if the input voltage VIN exceeds the range specified
in the Absolute Maximum Ratings table, the input current must be limited to the absolute maximum value
because the electrostatic discharge (ESD) protection turns on. Secondly, the linearity and parametric
performance of the device is ensured only when the analog input voltage remains within the linear full-scale
range (VFSR) as specified in the Recommended Operating Conditions table.
Copyright © 2022 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
8.3.2 Isolation Channel Signal Transmission
The AMC1311 uses an on-off keying (OOK) modulation scheme, as shown in 图 8-1, to transmit the modulator
output bitstream across the SiO2-based isolation barrier. The transmit driver (TX) shown in the Functional Block
Diagram transmits an internally-generated, high-frequency carrier across the isolation barrier to represent a
digital one and does not send a signal to represent a digital zero. The nominal frequency of the carrier used
inside the AMC1311 is 480 MHz.
The receiver (RX) on the other side of the isolation barrier recovers and demodulates the signal and provides the
input to the fourth-order analog filter. The AMC1311 transmission channel is optimized to achieve the highest
level of common-mode transient immunity (CMTI) and lowest level of radiated emissions caused by the high-
frequency carrier and RX/TX buffer switching.
Internal Clock
Modulator Bitstream
on High-side
Signal Across Isolation Barrier
Recovered Sigal
on Low-side
图8-1. OOK-Based Modulation Scheme
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
8.3.3 Analog Output
The AMC1311 provides a differential analog output on the OUTP and OUTN pins. For input voltages of VIN in the
range from –0.1 V to +2 V, the device provides a linear response with a nominal gain of 1. For example, for an
input voltage of 2 V, the differential output voltage (VOUTP – VOUTN) is 2 V. At zero input (IN shorted to GND1),
both pins output the same common-mode output voltage VCMout, as specified in the Electrical Characteristics
table. For input voltages greater than 2 V but less than approximately 2.5 V, the differential output voltage
continues to increase but with reduced linearity performance. The outputs saturate at a differential output voltage
of VCLIPout, as shown in 图8-2, if the input voltage exceeds the VClipping value.
Maximum input range before clipping (VClipping
)
Linear input range (VFSR
)
VFail-safe
VOUTN
VCLIPout
VOUTP
VCMout
0
2.516 V
Input Voltage (VIN
)
2 V
图8-2. Output Behavior of the AMC1311
The AMC1311 output offers a fail-safe feature that simplifies diagnostics on a system level. 图8-2 shows the fail-
safe mode, in which the AMC1311 outputs a negative differential output voltage that does not occur under
normal operating conditions. The fail-safe output is active in three cases:
• When the high-side supply VDD1 of the AMC1311 device is missing
• When the high-side supply VDD1 falls below the undervoltage threshold VDD1UV
• When the SHTDN pin is pulled high
Use the maximum VFail-safe voltage specified in the Electrical Characteristics table as a reference value for fail-
safe detection on a system level.
8.4 Device Functional Modes
The AMC1311 is operational when the power supplies VDD1 and VDD2 are applied, as specified in the
Recommended Operating Conditions table.
Copyright © 2022 Texas Instruments Incorporated
22
Submit Document Feedback
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
9 Application and Implementation
备注
以下应用部分中的信息不属于TI 器件规格的范围，TI 不担保其准确性和完整性。TI 的客 户应负责确定
器件是否适用于其应用。客户应验证并测试其设计，以确保系统功能。
9.1 Application Information
The high input impedance, low input bias current, low AC and DC errors, and low temperature drift make the
AMC1311 a high-performance solution for industrial applications where voltage sensing in the presence of high
common-mode voltage levels is required.
9.2 Typical Application
图9-1 shows the AMC1311 in a typical application. The DC bus voltage is divided down to an approximate
2-V level across the bottom resistor (RSNS) of a high-impedance resistive divider that is sensed by the
AMC1311. The AMC1311 digitizes the analog input signal on the high-side, transfers the data across the
isolation barrier to the low-side, reconstructs the analog signal, and presents this signal as a differential voltage
signal on the output pins.
The high-impedance input and the high common-mode transient immunity (CMTI) of the AMC1311 ensure
reliable and accurate operation even in high-noise environments.
+ DC Bus
Number of unit resistors depends
on design requirements.
See design examples for details.
RX1
High-side supply
(3.3 V or 5 V)
Low-side supply
(3.3 V or 5 V)
100 nF 1 uF
RX2
AMC1311B
Load
VDD1
VDD2
10
10
10 nF
ICROSS
RSNS
IN
OUTP
OUTN
GND2
ADC
SHTDN
GND1
1 uF 100 nF 100 pF
IGBT module
DC Bus
图9-1. Using the AMC1311 for DC Link Voltage Sensing in Frequency Inverters
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
23
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
9.2.1 Design Requirements
表9-1 lists the parameters for this typical application.
表9-1. Design Requirements
PARAMETER
System input voltage
VALUE
Single phase, 230 V, 50 Hz
400 V
Maximum DC link voltage
High-side supply voltage
3.3 V or 5 V
Low-side supply voltage
3.3 V or 5 V
Maximum resistor operating voltage
Voltage drop across the sense resistor (RSNS) for a linear response
Current through the resistive divider, ICROSS
75 V
2 V (maximum)
100 μA (maximum)
9.2.2 Detailed Design Procedure
The 100-μA, cross-current requirement at the maximum DC link voltage (400 V) determines that the total
impedance of the resistive divider is 4 MΩ. The impedance of the resistive divider is dominated by the top
portion (shown exemplary as RX1 and RX2 in 图 9-1) and the voltage drop across RSNS can be neglected for a
moment. The maximum allowed voltage drop per unit resistor is specified as 75 V; therefore, the minimum
number of unit resistors in the top portion of the resistive divider is 400 V / 75 V = 6. The calculated unit value is
4 MΩ/ 6 = 666 kΩand the next closest value from the E96 series is 665 kΩ.
RSNS is sized such that the voltage drop across the resistor at the maximum DC link voltage (400 V) equals the
linear full-scale range input voltage (VFSR) of the AMC1311, which is 2 V. This voltage is calculated as RSNS =
VFSR / (VDC-link, max – VFSR) × RTOP, where RTOP is the total value of the top resistor string (6 × 665 kΩ = 3990
kΩ). RSNS is calculated as 20.05 kΩand matches a value from the E96 series.
表9-2. Resistor Value Example
PARAMETER
VALUE
665 kΩ
6
Unit resistor RX
Number of unit resistors
Sense resistor RSNS
20.05 kΩ
99.7 μA
2.000 V
6.6 mW
39.9 mW
Resulting current through resistive divider ICROSS
Resulting voltage drop across sense resistor
Power dissipated in unit resistor RX
Total power dissipated in resistive divider
Copyright © 2022 Texas Instruments Incorporated
24
Submit Document Feedback
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
9.2.2.1 Input Filter Design
Placing an RC filter in front of the isolated amplifier improves signal-to-noise performance of the signal path. In
practice, however, the impedance of the resistor divider is high and only a small-value filter capacitor can be
used to not limit the signal bandwidth to an unacceptable low value. Design the input filter such that:
• The cutoff frequency of the filter is at least one order of magnitude lower than the sampling frequency
(20 MHz) of the internal ΔΣmodulator
• The input bias current does not generate significant voltage drop across the DC impedance of the input filter
Most voltage-sensing applications use high-impedance resistor dividers in front of the isolated amplifier to scale
down the input voltage. In this case, a single capacitor (as shown in 图9-2) is sufficient to filter the input signal.
VDC
R1
AMC1311B
R2
VDD1
VDD2
OUTP
OUTN
GND2
100 pF
IN
RSNS
SHTDN
GND1
图9-2. Input Filter
9.2.2.2 Differential to Single-Ended Output Conversion
图 9-3 shows an example of a TLV900x-based signal conversion and filter circuit for systems using single-ended
input ADCs to convert the analog output voltage into digital. With R1 = R2 = R3 = R4, the output voltage equals
(VOUTP –VOUTN) + VREF. Tailor the bandwidth of this filter stage to the bandwidth requirement of the system and
use NP0-type capacitors for best performance. For most applications, R1 = R2 = R3 = R4 = 3.3 kΩand C1 = C2
= 330 pF yields good performance.
C1
AMC1311B
R2
VDD1
VDD2
OUTP
OUTN
GND2
R1
R3
IN
–
+
ADC
To MCU
SHTDN
GND1
TLV9001
C2
R4
VREF
图9-3. Connecting the AMC1311 Output to a Single-Ended Input ADC
For more information on the general procedure to design the filtering and driving stages of SAR ADCs, see the
18-Bit, 1MSPS Data Acquisition Block (DAQ) Optimized for Lowest Distortion and Noise and 18-Bit Data
Acquisition Block (DAQ) Optimized for Lowest Power reference guides, available for download at www.ti.com.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
25
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
9.2.3 Application Curve
One important aspect of system design is the effective detection of an overvoltage condition to protect switching
devices and passive components from damage. To power off the system quickly in the event of an overvoltage
condition, a low delay caused by the isolated amplifier is required. 图 9-4 shows the typical full-scale step
response of the AMC1311.
VOUTP
VOUTN
VIN
图9-4. Step Response of the AMC1311
9.3 What To Do and What Not To Do
Do not leave the analog input (IN pin) of the AMC1311 unconnected (floating) when the device is powered up on
the high-side. If the device input is left floating, the bias current may generate a negative input voltage that
exceeds the specified input voltage range, causing the output of the device to be invalid.
Do not connect protection diodes to the input (IN pin) of the AMC1311. Diode leakage current can introduce
significant measurement error especially at high temperatures. The input pin is protected against high voltages
by its ESD protection circuit and the high impedance of the external restive divider.
Copyright © 2022 Texas Instruments Incorporated
26
Submit Document Feedback
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
10 Power Supply Recommendations
In a typical application, the high-side (VDD1) of the AMC1311 is powered from an already existing, high-side,
ground-referenced, 3.3-V or 5-V power supply in the system. Alternatively, the high-side supply can be
generated from the low-side supply (VDD2) by an isolated DC/DC converter. A low-cost solution is based on the
push-pull driver SN6501 and a transformer that supports the desired isolation voltage ratings.
The AMC1311 does not require any specific power-up sequencing. The high-side power supply (VDD1) is
decoupled with a low-ESR, 100-nF capacitor (C1) parallel to a low-ESR, 1-μF capacitor (C2). The low-side
power supply (VDD2) is equally decoupled with a low-ESR, 100-nF capacitor (C3) parallel to a low-ESR, 1-μF
capacitor (C4). Place all four capacitors (C1, C2, C3, and C4) as close to the device as possible. 图 10-1 shows
the proper decoupling layout for the AMC1311.
VDC
VDD1
VDD2
R1
R2
C2 1 µF
C4 1 µF
AMC1311B
C1 100 nF
C3 100 nF
VDD1
VDD2
OUTP
OUTN
GND2
IN
to RC filter / ADC
to RC filter / ADC
C5 100 pF
RSNS
SHTDN
GND1
图10-1. Decoupling of the AMC1311
Capacitors must provide adequate effective capacitance under the applicable DC bias conditions they
experience in the application. Multilayer ceramic capacitors (MLCC) typically exhibit only a fraction of their
nominal capacitance under real-world conditions and this factor must be taken into consideration when selecting
these capacitors. This problem is especially acute in low-profile capacitors, in which the dielectric field strength is
higher than in taller components. Reputable capacitor manufacturers provide capacitance versus DC bias curves
that greatly simplify component selection.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
27
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
11 Layout
11.1 Layout Guidelines
图 11-1 shows a layout recommendation with the critical placement of the decoupling capacitors (as close as
possible to the AMC1311 supply pins) and placement of the other components required by the device. For best
performance, place the sense resistor close to the device input pin (IN).
11.2 Layout Example
Clearance area, to be
kept free of any
conductive materials.
C4
C3
C2
C1
to RC filter / ADC
to RC filter / ADC
OUTP
OUTN
GND2
INP
AMC1311B
Top Metal
Inner or Bottom Layer Metal
Via
图11-1. Recommended Layout of the AMC1311
Copyright © 2022 Texas Instruments Incorporated
28
Submit Document Feedback
Product Folder Links: AMC1311
AMC1311
www.ti.com.cn
ZHCSH46C –DECEMBER 2017 –REVISED JUNE 2022
12 Device and Documentation Support
12.1 Documentation Support
12.1.1 Related Documentation
For related documentation, see the following:
• Texas Instruments, Isolation Glossary application report
• Texas Instruments, Semiconductor and IC Package Thermal Metrics application report
• Texas Instruments, ISO72x Digital Isolator Magnetic-Field Immunity application report
• Texas Instruments, TLV900x Low-Power, RRIO, 1-MHz Operational Amplifier for Cost-Sensitive Systems
data sheet
• Texas Instruments, SN6501 Transformer Driver for Isolated Power Supplies data sheet
• Texas Instruments, AMC1311EVM Users Guide
• Texas Instruments, 18-Bit, 1-MSPS Data Acquisition Block (DAQ) Optimized for Lowest Distortion and Noise
reference guide
• Texas Instruments, 18-Bit, 1-MSPS Data Acquisition Block (DAQ) Optimized for Lowest Power reference
guide
• Texas Instruments, Isolated Amplifier Voltage Sensing Excel Calculator design tool
12.2 接收文档更新通知
要接收文档更新通知，请导航至 ti.com 上的器件产品文件夹。点击订阅更新 进行注册，即可每周接收产品信息更
改摘要。有关更改的详细信息，请查看任何已修订文档中包含的修订历史记录。
12.3 支持资源
TI E2E™ 支持论坛是工程师的重要参考资料，可直接从专家获得快速、经过验证的解答和设计帮助。搜索现有解
答或提出自己的问题可获得所需的快速设计帮助。
链接的内容由各个贡献者“按原样”提供。这些内容并不构成 TI 技术规范，并且不一定反映 TI 的观点；请参阅
TI 的《使用条款》。
12.4 Trademarks
TI E2E™ is a trademark of Texas Instruments.
所有商标均为其各自所有者的财产。
12.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
12.6 术语表
TI 术语表
本术语表列出并解释了术语、首字母缩略词和定义。
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
29
Product Folder Links: AMC1311
PACKAGE OPTION ADDENDUM
www.ti.com
27-Jan-2021
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
AMC1311BDWV
AMC1311BDWVR
AMC1311DWV
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SOIC
SOIC
SOIC
SOIC
DWV
DWV
DWV
DWV
8
8
8
8
64
RoHS & Green
NIPDAU
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
-55 to 125
-55 to 125
-40 to 125
-40 to 125
1311B
1000 RoHS & Green
64 RoHS & Green
1000 RoHS & Green
NIPDAU
NIPDAU
NIPDAU
1311B
1311
1311
AMC1311DWVR
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
27-Jan-2021
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jun-2023
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
AMC1311BDWVR
AMC1311DWVR
SOIC
SOIC
DWV
DWV
8
8
1000
1000
330.0
330.0
16.4
16.4
12.15
12.15
6.2
6.2
3.05
3.05
16.0
16.0
16.0
16.0
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jun-2023
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
AMC1311BDWVR
AMC1311DWVR
SOIC
SOIC
DWV
DWV
8
8
1000
1000
356.0
356.0
356.0
356.0
35.0
35.0
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jun-2023
TUBE
T - Tube
height
L - Tube length
W - Tube
width
B - Alignment groove width
*All dimensions are nominal
Device
Package Name Package Type
Pins
SPQ
L (mm)
W (mm)
T (µm)
B (mm)
AMC1311BDWV
AMC1311DWV
DWV
DWV
SOIC
SOIC
8
8
64
64
505.46
505.46
13.94
13.94
4826
4826
6.6
6.6
Pack Materials-Page 3
PACKAGE OUTLINE
DWV0008A
SOIC - 2.8 mm max height
S
C
A
L
E
2
.
0
0
0
SOIC
C
SEATING PLANE
11.5 0.25
TYP
PIN 1 ID
AREA
0.1 C
6X 1.27
8
1
2X
5.95
5.75
NOTE 3
3.81
4
5
0.51
0.31
8X
7.6
7.4
0.25
C A
B
A
B
2.8 MAX
NOTE 4
0.33
0.13
TYP
SEE DETAIL A
(2.286)
0.25
GAGE PLANE
0.46
0.36
0 -8
1.0
0.5
DETAIL A
TYPICAL
(2)
4218796/A 09/2013
NOTES:
1. All linear dimensions are in millimeters. Dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm, per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm, per side.
www.ti.com
EXAMPLE BOARD LAYOUT
DWV0008A
SOIC - 2.8 mm max height
SOIC
8X (1.8)
SEE DETAILS
SYMM
SYMM
8X (0.6)
6X (1.27)
(10.9)
LAND PATTERN EXAMPLE
9.1 mm NOMINAL CLEARANCE/CREEPAGE
SCALE:6X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL
METAL
0.07 MAX
ALL AROUND
0.07 MIN
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4218796/A 09/2013
NOTES: (continued)
5. Publication IPC-7351 may have alternate designs.
6. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DWV0008A
SOIC - 2.8 mm max height
SOIC
SYMM
8X (1.8)
8X (0.6)
SYMM
6X (1.27)
(10.9)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:6X
4218796/A 09/2013
NOTES: (continued)
7. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
8. Board assembly site may have different recommendations for stencil design.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据（包括数据表）、设计资源（包括参考设计）、应用或其他设计建议、网络工具、安全信息和其他资源，
不保证没有瑕疵且不做出任何明示或暗示的担保，包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任：(1) 针对您的应用选择合适的 TI 产品，(2) 设计、验
证并测试您的应用，(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更，恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务，TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址：Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023，德州仪器 (TI) 公司
相关型号：
©2020 ICPDF网 联系我们和版权申明