OPA1612AIDR [TI]
High-Performance Bipolar-Input AUDIO OPERATIONAL AMPLIFIERS; 高性能双极输入音频运算放大器
| 型号： | OPA1612AIDR |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | High-Performance Bipolar-Input AUDIO OPERATIONAL AMPLIFIERS |
| 文件： | 总21页 (文件大小：719K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
OPA1611
OPA1612
Burr-Brown Audio
www.ti.com........................................................................................................................................................ SBOS450A –JULY 2009–REVISED AUGUST 2009
™ High-Performance, Bipolar-Input
AUDIO OPERATIONAL AMPLIFIERS
Check for Samples: OPA1611 OPA1612
1
FEATURES
DESCRIPTION
23
•
SUPERIOR SOUND QUALITY
The OPA1611 (single) and OPA1612 (dual)
bipolar-input operational amplifiers achieve very low
1.1nV/√Hz noise density with an ultralow distortion of
0.000015% at 1kHz. The OPA1611 and OPA1612
offer rail-to-rail output swing to within 600mV with a
2kΩ load, which increases headroom and maximizes
dynamic range. These devices also have a high
output drive capability of ±30mA.
•
•
ULTRALOW NOISE: 1.1nV/√Hz at 1kHz
ULTRALOW DISTORTION:
0.000015% AT 1kHz
•
•
HIGH SLEW RATE: 27V/μs
WIDE BANDWIDTH:
40MHz (G = +1)
•
•
•
HIGH OPEN-LOOP GAIN: 130dB
UNITY GAIN STABLE
These devices operate over a very wide supply range
of ±2.25V to ±18V, on only 3.6mA of supply current
per channel. The OPA1611 and OPA1612 op amps
are unity-gain stable and provide excellent dynamic
behavior over a wide range of load conditions.
LOW QUIESCENT CURRENT:
3.6mA (Single), 7.2mA (Dual)
•
•
•
RAIL-TO-RAIL OUTPUT
The dual version features completely independent
circuitry for lowest crosstalk and freedom from
interactions between channels, even when overdriven
or overloaded.
WIDE SUPPLY RANGE: ±2.25V to ±18V
SINGLE AND DUAL VERSIONS AVAILABLE
APPLICATIONS
Both the OPA1611 and OPA1612 are available in
SO-8 packages and are specified from –40°C to
+85°C. SoundPlus ™
•
•
•
•
•
•
PROFESSIONAL AUDIO EQUIPMENT
MICROPHONE PREAMPLIFIERS
ANALOG AND DIGITAL MIXING CONSOLES
BROADCAST STUDIO EQUIPMENT
AUDIO TEST AND MEASUREMENT
HIGH-END A/V RECEIVERS
V+
Pre-Output Driver
OUT
IN+
IN-
V-
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
3
SoundPlus is a trademark of Texas Instruments Incorporated.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009, Texas Instruments Incorporated
OPA1611
OPA1612
SBOS450A –JULY 2009–REVISED AUGUST 2009........................................................................................................................................................ www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ABSOLUTE MAXIMUM RATINGS(1)
Over operating free-air temperature range (unless otherwise noted).
VALUE
UNIT
V
Supply Voltage
VS = (V+) – (V–)
40
(V–) – 0.5 to (V+) + 0.5
±10
Input Voltage
V
Input Current (All pins except power-supply pins)
Output Short-Circuit(2)
Operating Temperature
Storage Temperature
mA
Continuous
(TA)
(TA)
(TJ)
–55 to +125
–65 to +150
200
°C
°C
°C
V
Junction Temperature
Human Body Model (HBM)
3000
ESD Ratings
Charged Device Model (CDM)
Machine Model (MM)
1000
V
200
V
(1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not supported.
(2) Short-circuit to VS/2 (ground in symmetrical dual supply setups), one amplifier per package.
PACKAGE INFORMATION(1)
PRODUCT
PACKAGE-LEAD
PACKAGE DESIGNATOR
PACKAGE MARKING
TI OPA
1611A
OPA1611
SO-8
D
TI OPA
1612A
OPA1612
SO-8
D
(1) For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
PIN CONFIGURATIONS
D PACKAGE
D PACKAGE
OPA1611, SO-8
OPA1612, SO-8
(TOP VIEW)
(TOP VIEW)
NC(1)
-IN
+IN
V-
1
2
3
4
8
7
6
5
NC(1)
V+
OUT A
-IN A
+IN A
V-
1
2
3
4
8
7
6
5
V+
A
OUT B
-IN B
+IN B
OUT
NC(1)
B
(1) NC denotes no internal connection. Pin can be left floating or connected to any voltage between (V–) and (V+).
2
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA1611 OPA1612
OPA1611
OPA1612
www.ti.com........................................................................................................................................................ SBOS450A –JULY 2009–REVISED AUGUST 2009
ELECTRICAL CHARACTERISTICS: VS = ±2.25V to ±18V
At TA = +25°C and RL = 2kΩ, unless otherwise noted. VCM = VOUT = midsupply, unless otherwise noted.
Boldface limits apply over the specified temperature range, TA = –40°C to +85°C.
OPA1611AI, OPA1612AI
PARAMETER
AUDIO PERFORMANCE
CONDITIONS
MIN
TYP
MAX
UNIT
0.000015
–136
%
Total Harmonic Distortion +
Noise
THD+N
IMD
G = +1, f = 1kHz, VO = 3VRMS
G = +1, VO = 3VRMS
dB
Intermodulation Distortion
0.000015
–136
%
dB
%
SMPTE/DIN Two-Tone, 4:1 (60Hz and 7kHz)
0.000012
–138
DIM 30 (3kHz square wave and 15kHz sine wave)
CCIF Twin-Tone (19kHz and 20kHz)
dB
%
0.000008
–142
dB
FREQUENCY RESPONSE
Gain-Bandwidth Product
GBW
SR
G = 100
G = 1
80
40
MHz
MHz
V/μs
MHz
ns
Slew Rate
G = –1
27
Full Power Bandwidth(1)
Overload Recovery Time
Channel Separation (Dual)
NOISE
VO = 1VPP
G = –10
f = 1kHz
4
500
–130
dB
Input Voltage Noise
Input Voltage Noise Density
f = 20Hz to 20kHz
f = 10Hz
1.2
2
μVPP
en
nV/√Hz
nV/√Hz
nV/√Hz
pA/√Hz
pA/√Hz
f = 100Hz
f = 1kHz
1.5
1.1
3
Input Current Noise Density
In
f = 10Hz
f = 1kHz
1.7
OFFSET VOLTAGE
Input Offset Voltage
over Temperature(2)
vs Power Supply
VOS
dVOS/dT
PSRR
VS = ±15V
VS = ±2.25V to ±18V
VCM = 0V
±100
1
±500
μV
4
μV/°C
μV/V
0.1
1
INPUT BIAS CURRENT
Input Bias Current
over Temperature(2)
Input Offset Current
INPUT VOLTAGE RANGE
IB
±60
±25
±250
350
nA
nA
nA
IOS
VCM = 0V
±175
Common-Mode Voltage
Range
VCM
(V–) + 2
110
(V+) – 2
V
Common-Mode Rejection
Ratio
CMRR
(V–) + 2V ≤ VCM ≤ (V+) – 2V
120
dB
INPUT IMPEDANCE
Differential
20k || 8
109 || 2
Ω || pF
Ω || pF
Common-Mode
(1) Full-power bandwidth = SR/(2π × VPP), where SR = slew rate.
(2) Specified by design and characterization.
Copyright © 2009, Texas Instruments Incorporated
3
Product Folder Link(s): OPA1611 OPA1612
OPA1611
OPA1612
SBOS450A –JULY 2009–REVISED AUGUST 2009........................................................................................................................................................ www.ti.com
ELECTRICAL CHARACTERISTICS: VS = ±2.25V to ±18V (continued)
At TA = +25°C and RL = 2kΩ, unless otherwise noted. VCM = VOUT = midsupply, unless otherwise noted.
Boldface limits apply over the specified temperature range, TA = –40°C to +85°C.
OPA1611AI, OPA1612AI
PARAMETER
OPEN-LOOP GAIN
CONDITIONS
MIN
TYP
MAX
UNIT
Open-Loop Voltage Gain
AOL
AOL
(V–) + 0.2V ≤ VO ≤ (V+) – 0.2V, RL = 10kΩ
(V–) + 0.6V ≤ VO ≤ (V+) – 0.6V, RL = 2kΩ
114
110
130
114
dB
dB
OUTPUT
Voltage Output
VOUT
RL = 10kΩ, AOL ≥ 114dB
RL = 2kΩ, AOL ≥ 110dB
(V–) + 0.2
(V–) + 0.6
(V+) – 0.2
(V+) – 0.6
V
V
Output Current
IOUT
ZO
See Figure 27
See Figure 28
+55/–62
mA
Open-Loop Output
Impedance
Ω
Short-Circuit Current
Capacitive Load Drive
POWER SUPPLY
Specified Voltage
ISC
mA
pF
CLOAD
See Typical Characteristics
VS
IQ
±2.25
±18
V
Quiescent Current
(per channel)
over Temperature(3)
TEMPERATURE RANGE
Specified Range
IOUT = 0A
3.6
4.5
mA
mA
5.5
–40
–55
+85
°C
°C
Operating Range
Thermal Resistance
SO-8
+125
θ JA
150
°C/W
(3) Specified by design and characterization.
4
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA1611 OPA1612
OPA1611
OPA1612
www.ti.com........................................................................................................................................................ SBOS450A –JULY 2009–REVISED AUGUST 2009
TYPICAL CHARACTERISTICS
At TA = +25°C, VS = ±15V, and RL = 2kΩ, unless otherwise noted.
INPUT VOLTAGE NOISE DENSITY AND
INPUT CURRENT NOISE DENSITY vs FREQUENCY
0.1Hz TO 10Hz NOISE
100
Voltage Noise Density
10
Current Noise Density
1
Time (1s/div)
0.1
1
10
100
1k
10k
100k
Frequency (Hz)
Figure 1.
Figure 2.
VOLTAGE NOISE vs SOURCE RESISTANCE
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
30
10k
1k
Maximum output
voltage range
VS = ±15V
25
20
15
10
5
without slew-rate
induced distortion
EO
Total Output
Voltage Noise
RS
100
10
1
VS = ±5V
Resistor
Noise
VS = ±2.25V
EO2 = en2 + (in RS)2 + 4kTRS
0
10k
100k
Frequency (Hz)
1M
10M
100
1k
10k
100k
1M
Source Resistance, RS (W)
Figure 3.
Figure 4.
GAIN AND PHASE vs FREQUENCY
CLOSED-LOOP GAIN vs FREQUENCY
140
120
100
80
180
160
140
120
100
80
25
20
G = +10
15
Gain
10
G = -1
5
G = +1
60
0
40
-5
20
60
Phase
-10
-15
-20
-25
0
40
-20
-40
20
0
100
1k
10k
100k
1M
10M
100M
100k
1M
10M
100M
Frequency (Hz)
Frequency (Hz)
Figure 5.
Figure 6.
Copyright © 2009, Texas Instruments Incorporated
5
Product Folder Link(s): OPA1611 OPA1612
OPA1611
OPA1612
SBOS450A –JULY 2009–REVISED AUGUST 2009........................................................................................................................................................ www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = ±15V, and RL = 2kΩ, unless otherwise noted.
THD+N RATIO vs FREQUENCY
THD+N RATIO vs FREQUENCY
-80
0.0001
-120
0.01
0.001
VOUT = 3VRMS
VOUT = 3VRMS
+15V
OPA1611
-15V
G = +1
RL = 600W
BW = 80kHz
BW = 80kHz
RSOURCE
RL
G = +1
RL = 2kW
-100
-120
-140
RSOURCE = 600W
RSOURCE = 0W
RSOURCE = 150W
G = -1
RSOURCE = 300W
0.0001
0.00001
RL = 600W
G = -1, RL = 2kW
0.00001
-140
10
100
1k
10k 20k
20
100
1k
10k 20k
Frequency (Hz)
Frequency (Hz)
Figure 7.
Figure 8.
THD+N RATIO vs FREQUENCY
THD+N RATIO vs FREQUENCY
-80
-100
-120
-140
0.001
0.01
0.001
VOUT = 3VRMS
BW > 500kHz
VOUT = 3VRMS
BW > 500kHz
+15V
OPA1611
-15V
G = +1
RL = 600W
RSOURCE
RL
-100
-120
-140
RSOURCE = 600W
RSOURCE = 300W
G = -1
RL = 600W
0.0001
0.0001
0.00001
G = -1
RL = 2kW
G = +1
RL = 2kW
RSOURCE = 150W
RSOURCE = 0W
0.00001
10
100
1k
10k
100k
10
100
1k
10k
100k
Frequency (Hz)
Frequency (Hz)
Figure 9.
Figure 10.
INTERMODULATION DISTORTION vs
OUTPUT AMPLITUDE
THD+N RATIO vs OUTPUT AMPLITUDE
-80
-80
0.01
0.001
0.01
1kHz Signal
BW = 80kHz
RSOURCE = 0W
G = +1
SMPTE/DIN
Two-Tone
4:1 (60Hz and 7kHz)
-100
-120
-140
-160
-100
-120
-140
-160
0.001
0.0001
DIM30
(3kHz square wave
and 15kHz sine wave)
0.0001
G = -1, RL = 2kW
G = -1, RL = 600W
G = +1, RL = 2kW
G = +1, RL = 600W
0.00001
0.000001
0.00001
0.000001
CCIF Twin-Tone
(19kHz and 20kHz)
0.01
0.1
1
10 20
0.1
1
10
20
Output Amplitude (VRMS
)
Output Amplitude (VRMS)
Figure 11.
Figure 12.
6
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA1611 OPA1612
OPA1611
OPA1612
www.ti.com........................................................................................................................................................ SBOS450A –JULY 2009–REVISED AUGUST 2009
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = ±15V, and RL = 2kΩ, unless otherwise noted.
CHANNEL SEPARATION vs FREQUENCY
CMRR AND PSRR vs FREQUENCY (Referred to Input)
-80
-90
160
VS = ±15V
VOUT = 3.5VRMS
140
-PSRR
-100
-110
-120
-130
-140
-150
-160
-170
-180
G = +1
RL = 600W
120
+PSRR
100
CMRR
80
60
40
20
0
RL = 2kW
RL = 5kW
10
100
1k
10k
100k
1
10
100
1k
10k 100k
1M
10M 100M
Frequency (Hz)
Frequency (Hz)
Figure 13.
Figure 14.
SMALL-SIGNAL STEP RESPONSE
(100mV)
SMALL-SIGNAL STEP RESPONSE
(100mV)
G = +1
CL = 50pF
G = -1
CL = 50pF
CF = 5.6pF
+15V
OPA1611
-15V
RI = 2kW RF = 2kW
+15V
OPA1611
RL
CL
CL
-15V
Time (01.ms/div)
Time (0.1ms/div)
Figure 15.
Figure 16.
LARGE-SIGNAL STEP RESPONSE
LARGE-SIGNAL STEP RESPONSE
G = +1
CL = 50pF
G = -1
CL = 50pF
RL = 2kW
RF = 0W
RL = 2kW
RF = 75W
See Applications Information,
Input Protection section
Time (0.5ms/div)
Time (0.5ms/div)
Figure 17.
Figure 18.
Copyright © 2009, Texas Instruments Incorporated
7
Product Folder Link(s): OPA1611 OPA1612
OPA1611
OPA1612
SBOS450A –JULY 2009–REVISED AUGUST 2009........................................................................................................................................................ www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = ±15V, and RL = 2kΩ, unless otherwise noted.
SMALL-SIGNAL OVERSHOOT
SMALL-SIGNAL OVERSHOOT
vs CAPACITIVE LOAD (100mV Output Step)
vs CAPACITIVE LOAD (100mV Output Step)
25
20
15
10
5
50
40
30
20
10
0
CF = 5.6pF
+15V
RS = 0W
RS = 0W
RF = 2kW
RI = 2kW
RS
OPA1611
RS = 25W
+15V
RL
CL
RS
-15V
OPA1611
RS = 25W
CL
-15V
RS = 50W
RS = 50W
G = -1
G = +1
0
0
100 200 300 400 500 600 700 800 900 1000
Capacitive Load (pF)
0
100
200
300
400
500
600
Capacitive Load (pF)
Figure 19.
Figure 20.
OPEN-LOOP GAIN vs TEMPERATURE
IB AND IOS vs TEMPERATURE
120
100
80
60
40
20
0
1.0
0.8
0.6
-IB
0.4
0.2
10kW
0
+IB
-0.2
-0.4
-0.6
-0.8
-1.0
IOS
2kW
-40
-15
10
35
50
85
-40
-15
10
35
60
85
Temperature (°C)
Temperature (°C)
Figure 21.
Figure 22.
IB AND IOS vs COMMON-MODE VOLTAGE
QUIESCENT CURRENT vs TEMPERATURE
80
70
60
50
40
30
20
10
0
5.0
4.5
4.0
3.5
3.0
2.5
2.0
VS = ±18V
+IB
IOS
-IB
Common-Mode Range
-10
-20
-18
-12
-6
0
6
12
18
-40
-15
10
35
60
85
Common-Mode Voltage (V)
Temperature (°C)
Figure 23.
Figure 24.
8
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA1611 OPA1612
OPA1611
OPA1612
www.ti.com........................................................................................................................................................ SBOS450A –JULY 2009–REVISED AUGUST 2009
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = ±15V, and RL = 2kΩ, unless otherwise noted.
QUIESCENT CURRENT vs SUPPLY VOLTAGE
SHORT-CIRCUIT CURRENT vs TEMPERATURE
4.0
3.9
3.8
3.7
3.6
3.5
3.4
3.3
3,2
3.1
3.0
75
70
65
60
55
50
45
40
35
30
-ISC
+ISC
Specified Supply-Voltage Range
0
4
8
12
16
20
24
28
32
36
-50
-25
0
25
50
75
100
125
Supply Voltage (V)
Temperature (°C)
Figure 25.
Figure 26.
OPEN-LOOP OUTPUT IMPEDANCE vs
FREQUENCY
OUTPUT VOLTAGE vs OUTPUT CURRENT
10k
1k
15
14
13
VS = ±15V
100
+25°C
Dual version with
both channels
driven simultaneously
+85°C
-40°C
10
1
-13
-14
-15
0.1
10
100
1k
10k
100k
1M
10M
100M
0
10
20
30
40
50
Output Current (mA)
Frequency (Hz)
Figure 27.
Figure 28.
Copyright © 2009, Texas Instruments Incorporated
9
Product Folder Link(s): OPA1611 OPA1612
OPA1611
OPA1612
SBOS450A –JULY 2009–REVISED AUGUST 2009........................................................................................................................................................ www.ti.com
APPLICATION INFORMATION
applications do not require equal positive and
The OPA1611 and OPA1612 are unity-gain stable,
negative output voltage swing. With the OPA161x
precision op amps with very low noise; these devices
series, power-supply voltages do not need to be
are also free from output phase reversal. Applications
equal. For example, the positive supply could be set
with noisy or high-impedance power supplies require
to +25V with the negative supply at –5V.
decoupling capacitors close to the device
power-supply pins. In most cases, 0.1μF capacitors
are adequate. Figure 29 shows a simplified internal
schematic of the OPA1611.
In all cases, the common-mode voltage must be
maintained within the specified range. In addition, key
parameters are assured over the specified
temperature range of TA
= –40°C to +85°C.
Parameters that vary with operating voltage or
temperature are shown in the Typical Characteristics.
OPERATING VOLTAGE
The OPA161x series op amps operate from ±2.25V
to ±18V supplies while maintaining excellent
performance. The OPA161x series can operate with
as little as +4.5V between the supplies and with up to
+36V between the supplies. However, some
V+
Pre-Output Driver
OUT
IN+
IN-
V-
Figure 29. OPA1611 Simplified Schematic
10
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA1611 OPA1612
OPA1611
OPA1612
www.ti.com........................................................................................................................................................ SBOS450A –JULY 2009–REVISED AUGUST 2009
INPUT PROTECTION
current noise is negligible, and voltage noise
generally dominates. The low voltage noise of the
OPA161x series op amps makes them a good choice
for use in applications where the source impedance is
less than 1kΩ.
The input terminals of the OPA1611 and the
OPA1612 are protected from excessive differential
voltage with back-to-back diodes, as Figure 30
illustrates. In most circuit applications, the input
protection circuitry has no consequence. However, in
low-gain or G = +1 circuits, fast ramping input signals
can forward bias these diodes because the output of
the amplifier cannot respond rapidly enough to the
input ramp. This effect is illustrated in Figure 17 of
the Typical Characteristics. If the input signal is fast
enough to create this forward bias condition, the input
signal current must be limited to 10mA or less. If the
input signal current is not inherently limited, an input
series resistor (RI) and/or a feedback resistor (RF)
can be used to limit the signal input current. This
input series resistor degrades the low-noise
performance of the OPA1611 and is examined in the
following Noise Performance section. Figure 30
shows an example configuration when both
current-limiting input and feedback resistors are used.
The equation in Figure 31 shows the calculation of
the total circuit noise, with these parameters:
•
•
•
•
•
en = Voltage noise
In = Current noise
RS = Source impedance
k = Boltzmann’s constant = 1.38 × 10–23 J/K
T = Temperature in degrees Kelvin (K)
VOLTAGE NOISE SPECTRAL DENSITY
vs SOURCE RESISTANCE
10k
EO
Total Output
Voltage Noise
1k
100
10
RS
RF
Resistor
Noise
-
EO2 = en2 + (in RS)2 + 4kTRS
OPA1611
Output
1
100
1k
10k
100k
1M
RI
+
Source Resistance, RS (W)
Input
Figure 31. Noise Performance of the OPA1611 in
Unity-Gain Buffer Configuration
Figure 30. Pulsed Operation
BASIC NOISE CALCULATIONS
NOISE PERFORMANCE
Design of low-noise op amp circuits requires careful
Figure 31 shows the total circuit noise for varying
source impedances with the op amp in a unity-gain
configuration (no feedback resistor network, and
therefore no additional noise contributions).
consideration of
a
variety of possible noise
contributors: noise from the signal source, noise
generated in the op amp, and noise from the
feedback network resistors. The total noise of the
circuit is the root-sum-square combination of all noise
components.
The OPA1611 (GBW = 40MHz, G = +1) is shown
with total circuit noise calculated. The op amp itself
contributes both a voltage noise component and a
current noise component. The voltage noise is
commonly modeled as a time-varying component of
the offset voltage. The current noise is modeled as
the time-varying component of the input bias current
and reacts with the source resistance to create a
voltage component of noise. Therefore, the lowest
noise op amp for a given application depends on the
source impedance. For low source impedance,
The resistive portion of the source impedance
produces thermal noise proportional to the square
root of the resistance. Figure 31 plots this function.
The source impedance is usually fixed; consequently,
select the op amp and the feedback resistors to
minimize the respective contributions to the total
noise.
Copyright © 2009, Texas Instruments Incorporated
11
Product Folder Link(s): OPA1611 OPA1612
OPA1611
OPA1612
SBOS450A –JULY 2009–REVISED AUGUST 2009........................................................................................................................................................ www.ti.com
Figure 32 illustrates both inverting and noninverting
op amp circuit configurations with gain. In circuit
configurations with gain, the feedback network
resistors also contribute noise. The current noise of
the op amp reacts with the feedback resistors to
create additional noise components. The feedback
resistor values can generally be chosen to make
these noise sources negligible. The equations for
total noise are shown for both configurations.
Noise in Noninverting Gain Configuration
Noise at the output:
R2
2
2
R2
R1
R2
R1
2
EO
R1
=
1 +
en2 + e12 + e22 + (inR2)2 + eS2 + (inRS)2 1 +
EO
R2
Where eS = Ö4kTRS
e1 = Ö4kTR1
´
= thermal noise of RS
1 +
R1
RS
R2
R1
´
= thermal noise of R1
VS
e2 = Ö4kTR2 = thermal noise of R2
Noise in Inverting Gain Configuration
Noise at the output:
R2
2
R2
2
EO
2
=
1 +
en2 + e12 + e22 + (inR2)2 + eS
R1
R1 + RS
EO
RS
R2
Where eS = Ö4kTRS
´
= thermal noise of RS
= thermal noise of R1
R1 + RS
VS
R2
e1 = Ö4kTR1
´
R1 + RS
e2 = Ö4kTR2 = thermal noise of R2
For the OPA161x series op amps at 1kHz, en = 1.1nV/√Hz and in = 1.7pA/√Hz.
Figure 32. Noise Calculation in Gain Configurations
12
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA1611 OPA1612
OPA1611
OPA1612
www.ti.com........................................................................................................................................................ SBOS450A –JULY 2009–REVISED AUGUST 2009
TOTAL HARMONIC DISTORTION
MEASUREMENTS
Validity of this technique can be verified by
duplicating measurements at high gain and/or high
frequency where the distortion is within the
measurement capability of the test equipment.
Measurements for this data sheet were made with an
Audio Precision System Two distortion/noise
analyzer, which greatly simplifies such repetitive
measurements. The measurement technique can,
however, be performed with manual distortion
measurement instruments.
The OPA161x series op amps have excellent
distortion characteristics. THD + Noise is below
0.00008% (G = +1, VO = 3VRMS, BW = 80kHz)
throughout the audio frequency range, 20Hz to
20kHz, with
a
2kΩ load (see Figure
7
for
characteristic performance).
The distortion produced by OPA1611 series op amps
is below the measurement limit of many commercially
available distortion analyzers. However, a special test
circuit (such as Figure 33 shows) can be used to
extend the measurement capabilities.
CAPACITIVE LOADS
The dynamic characteristics of the OPA1611 and
OPA1612 have been optimized for commonly
encountered gains, loads, and operating conditions.
The combination of low closed-loop gain and high
capacitive loads decreases the phase margin of the
amplifier and can lead to gain peaking or oscillations.
As a result, heavier capacitive loads must be isolated
from the output. The simplest way to achieve this
isolation is to add a small resistor (RS equal to 50Ω,
for example) in series with the output.
Op amp distortion can be considered an internal error
source that can be referred to the input. Figure 33
shows a circuit that causes the op amp distortion to
be 101 times (or approximately 40dB) greater than
that normally produced by the op amp. The addition
of R3 to the otherwise standard noninverting amplifier
configuration alters the feedback factor or noise gain
of the circuit. The closed-loop gain is unchanged, but
the feedback available for error correction is reduced
by a factor of 101, thus extending the resolution by
101. Note that the input signal and load applied to the
op amp are the same as with conventional feedback
without R3. The value of R3 should be kept small to
minimize its effect on the distortion measurements.
This small series resistor also prevents excess power
dissipation if the output of the device becomes
shorted. Figure 19 and Figure 20 illustrate graphs of
Small-Signal Overshoot vs Capacitive Load for
several values of RS. Also, refer to Applications
Bulletin AB-028 (literature number SBOA015,
available for download from the TI web site) for
details of analysis techniques and application circuits.
R1
R2
SIG. DIST.
R1
¥
R2
R3
GAIN GAIN
1
101
101
1kW
5kW
10W
50W
R3
OPA1611
VO = 3VRMS
-1
5kW
R2
R1
Signal Gain = 1+
R2
Distortion Gain = 1+
R1 II R3
Generator
Output
Analyzer
Input
Audio Precision
System Two(1)
Load
with PC Controller
(1) For measurement bandwidth, see Figure 7 through Figure 12.
Figure 33. Distortion Test Circuit
Copyright © 2009, Texas Instruments Incorporated
13
Product Folder Link(s): OPA1611 OPA1612
OPA1611
OPA1612
SBOS450A –JULY 2009–REVISED AUGUST 2009........................................................................................................................................................ www.ti.com
POWER DISSIPATION
circuits contained in the OPA161x series (indicated
by the dashed line area). The ESD protection circuitry
involves several current-steering diodes connected
from the input and output pins and routed back to the
internal power-supply lines, where they meet at an
absorption device internal to the operational amplifier.
This protection circuitry is intended to remain inactive
during normal circuit operation.
OPA1611 and OPA1612 series op amps are capable
of driving 2kΩ loads with a power-supply voltage up
to ±18V. Internal power dissipation increases when
operating at high supply voltages. Copper leadframe
construction used in the OPA1611 and OPA1612
series op amps improves heat dissipation compared
to conventional materials. Circuit board layout can
also help minimize junction temperature rise. Wide
copper traces help dissipate the heat by acting as an
additional heat sink. Temperature rise can be further
minimized by soldering the devices to the circuit
board rather than using a socket.
An ESD event produces
a
short duration,
high-voltage pulse that is transformed into a short
duration, high-current pulse as it discharges through
a semiconductor device. The ESD protection circuits
are designed to provide a current path around the
operational amplifier core to prevent it from being
damaged. The energy absorbed by the protection
circuitry is then dissipated as heat.
ELECTRICAL OVERSTRESS
Designers often ask questions about the capability of
an operational amplifier to withstand electrical
overstress. These questions tend to focus on the
device inputs, but may involve the supply voltage pins
or even the output pin. Each of these different pin
functions have electrical stress limits determined by
the voltage breakdown characteristics of the
particular semiconductor fabrication process and
specific circuits connected to the pin. Additionally,
internal electrostatic discharge (ESD) protection is
built into these circuits to protect them from
accidental ESD events both before and during
product assembly.
When an ESD voltage develops across two or more
of the amplifier device pins, current flows through one
or more of the steering diodes. Depending on the
path that the current takes, the absorption device
may activate. The absorption device has a trigger, or
threshold voltage, that is above the normal operating
voltage of the OPA161x but below the device
breakdown voltage level. Once this threshold is
exceeded, the absorption device quickly activates
and clamps the voltage across the supply rails to a
safe level.
It is helpful to have a good understanding of this
basic ESD circuitry and its relevance to an electrical
overstress event. Figure 34 illustrates the ESD
14
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA1611 OPA1612
OPA1611
OPA1612
www.ti.com........................................................................................................................................................ SBOS450A –JULY 2009–REVISED AUGUST 2009
When the operational amplifier connects into a circuit
such as the one Figure 34 shows, the ESD protection
components are intended to remain inactive and not
become involved in the application circuit operation.
However, circumstances may arise where an applied
voltage exceeds the operating voltage range of a
given pin. Should this condition occur, there is a risk
that some of the internal ESD protection circuits may
be biased on, and conduct current. Any such current
flow occurs through steering diode paths and rarely
involves the absorption device.
direct current path is established between the +VS
and –VS supplies. The power dissipation of the
absorption device is quickly exceeded, and the
extreme internal heating destroys the operational
amplifier.
Another common question involves what happens to
the amplifier if an input signal is applied to the input
while the power supplies +VS and/or –VS are at 0V.
Again, it depends on the supply characteristic while at
0V, or at a level below the input signal amplitude. If
the supplies appear as high impedance, then the
operational amplifier supply current may be supplied
by the input source via the current steering diodes.
This state is not a normal bias condition; the amplifier
most likely will not operate normally. If the supplies
are low impedance, then the current through the
steering diodes can become quite high. The current
level depends on the ability of the input source to
deliver current, and any resistance in the input path.
Figure 34 depicts a specific example where the input
voltage, VIN, exceeds the positive supply voltage
(+VS) by 500mV or more. Much of what happens in
the circuit depends on the supply characteristics. If
+VS can sink the current, one of the upper input
steering diodes conducts and directs current to +VS.
Excessively high current levels can flow with
increasingly higher VIN. As a result, the datasheet
specifications recommend that applications limit the
input current to 10mA.
If there is an uncertainty about the ability of the
supply to absorb this current, external zener diodes
may be added to the supply pins as shown in
Figure 34. The zener voltage must be selected such
that the diode does not turn on during normal
operation. However, its zener voltage should be low
enough so that the zener diode conducts if the supply
pin begins to rise above the safe operating supply
voltage level.
If the supply is not capable of sinking the current, VIN
may begin sourcing current to the operational
amplifier, and then take over as the source of positive
supply voltage. The danger in this case is that the
voltage can rise to levels that exceed the operational
amplifier absolute maximum ratings. In extreme but
rare cases, the absorption device triggers on while
+VS and –VS are applied. If this event happens, a
RF
+VS
+V
OPA1611
RI
ESD Current-
Steering Diodes
Out
-In
Op-Amp
Core
+In
Edge-Triggered ESD
Absorption Circuit
RL
ID
(1)
VIN
-V
-VS
(1) VIN = +VS + 500mV.
Figure 34. Equivalent Internal ESD Circuitry and Its Relation to a Typical Circuit Application
Copyright © 2009, Texas Instruments Incorporated
15
Product Folder Link(s): OPA1611 OPA1612
OPA1611
OPA1612
SBOS450A –JULY 2009–REVISED AUGUST 2009........................................................................................................................................................ www.ti.com
APPLICATION CIRCUIT
820W
2200pF
0.1mF
+VA
(+15V)
330W
IOUTL+
OPA1611
2700pF
-VA
(-15V)
680W
620W
0.1mF
+VA
(+15V)
0.1mF
Audio DAC
with Differential
Current
Outputs
100W
L Ch
Output
820W
OPA1611
8200pF
2200pF
-VA
(-15V)
0.1mF
0.1mF
+VA
(+15V)
680W
620W
IOUTL-
OPA1611
2700pF
330W
-VA
(-15V)
0.1mF
Figure 35. Audio DAC Post Filter (I/V Converter and Low-Pass Filter)
16
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA1611 OPA1612
PACKAGE OPTION ADDENDUM
www.ti.com
18-Aug-2009
PACKAGING INFORMATION
Orderable Device
OPA1611AID
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
SOIC
D
8
8
8
8
75 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
OPA1611AIDR
OPA1612AID
SOIC
SOIC
SOIC
D
D
D
2500 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
75 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
OPA1612AIDR
2500 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
15-Aug-2009
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
OPA1611AIDR
OPA1612AIDR
SOIC
SOIC
D
D
8
8
2500
2500
330.0
330.0
12.4
12.4
6.4
6.4
5.2
5.2
2.1
2.1
8.0
8.0
12.0
12.0
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
15-Aug-2009
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
OPA1611AIDR
OPA1612AIDR
SOIC
SOIC
D
D
8
8
2500
2500
346.0
346.0
346.0
346.0
29.0
29.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
www.ti.com/audio
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Logic
Power Mgmt
Microcontrollers
RFID
Telephony
Video & Imaging
Wireless
RF/IF and ZigBee® Solutions www.ti.com/lprf
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated
相关型号：
OPA1612AIDRGT
SoundPlus™ Audio Operational Amplifier with 1.1nV/√Hz Noise, Low THD and Precision 8-SON -40 to 85
TI
©2020 ICPDF网 联系我们和版权申明