TPL5010DDCT [TI]
具有看门狗功能和手动复位功能的毫微功耗系统计时器 | DDC | 6 | -40 to 105;型号: | TPL5010DDCT |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有看门狗功能和手动复位功能的毫微功耗系统计时器 | DDC | 6 | -40 to 105 |
文件: | 总27页 (文件大小:899K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
TPL5010
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
具有看门狗功能的 TPL5010 纳瓦级功耗系统计时器
1 特性
3 说明
1
•
•
•
•
•
•
•
电源电压范围为 1.8V 至 5.5V
TPL5010 纳瓦级计时器是一款超低功耗计时器,其看
门狗功能专为占空比、电池供电型 应用 (比如物联网
中的应用)中的系统唤醒功能而设计。其中许多 应用
需要使用 μC,因此,通常希望将 μC 维持在低功耗模
式以更大限度节省电流,而仅在某些时间间隔内唤醒以
收集数据或为中断提供服务。虽然 μC 的内部计时器可
用于系统唤醒,但它可能单独消耗数微安的总系统电
流。
电压为 2.5V 时,电流消耗为 35nA(典型值)
可选计时间隔:100ms 至 7200s
计时器精度:1%(典型值)
可通过电阻选择时间间隔
看门狗功能
手动复位
2 应用
TPL5010 仅消耗 35nA,可替代集成式 μC 计时器的功
能。这样就可将 μC 置于低得多的功耗模式,将内部计
时器关闭,并在被 TPL5010 中断时仅返回到激活模
式。TPL5010 通过提供近两个数量级的功率节省,可
以大幅减小能量采集或无线传感器 应用中所使用的电
池尺寸。TPL5010 提供 100ms 至 7200s 的可选时间
间隔,适用于中断驱动型 应用。出于安全考虑,某些
标准(如 EN50271)要求实现看门狗功能。TPL5010
不仅实现了看门狗功能,而且几乎没有增加功耗。
TPL5010 采用 6 引脚小外形尺寸晶体管 (SOT23) 封
装。
•
•
•
•
•
•
•
•
•
电池供电系统
物联网 (IoT)
出入探测
篡改检测
家庭自动化传感器
温度调节装置
消费类电子产品
远程传感器
白色家电
器件信息(1)
器件编号
TPL5010
封装
SOT23 (6)
封装尺寸(标称值)
3.00mm × 3.00mm
(1) 如需了解所有可用封装,请参阅产品说明书末尾的可订购产品
附录。
简化应用电路原理图
µC
VOUT
VIN
Rp
TPL5010
RSTn
VDD
VDD
GND
RSTn
GPIO
GPIO
Battery
POWER MANAGEMENT
GND
WAKE
DONE
DELAY/
M_RST
REXT
GND
1
本文档旨在为方便起见,提供有关 TI 产品中文版本的信息,以确认产品的概要。 有关适用的官方英文版本的最新信息,请访问 www.ti.com,其内容始终优先。 TI 不保证翻译的准确
性和有效性。 在实际设计之前,请务必参考最新版本的英文版本。
English Data Sheet: SNAS651
TPL5010
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
www.ti.com.cn
目录
8.3 Feature Description................................................... 9
8.4 Device Functional Modes........................................ 10
8.5 Programming .......................................................... 10
Application and Implementation ........................ 16
9.1 Application Information............................................ 16
9.2 Typical Application ................................................. 16
1
2
3
4
5
6
7
特性.......................................................................... 1
应用.......................................................................... 1
说明.......................................................................... 1
修订历史记录 ........................................................... 2
器件比较表............................................................... 3
Pin Configuration and Functions......................... 4
Specifications......................................................... 5
7.1 Absolute Maximum Ratings ...................................... 5
7.2 ESD Ratings.............................................................. 5
7.3 Recommended Operating Ratings ........................... 5
7.4 Thermal Information ................................................. 5
7.5 Electrical Characteristics........................................... 6
7.6 Timing Requirements ............................................... 7
7.7 Typical Characteristics.............................................. 8
Detailed Description .............................................. 9
8.1 Overview ................................................................... 9
8.2 Functional Block Diagram ......................................... 9
9
10 Power Supply Recommendations ..................... 18
11 Layout................................................................... 18
11.1 Layout Guidelines ................................................. 18
11.2 Layout Example .................................................... 18
12 器件和文档支持 ..................................................... 19
12.1 接收文档更新通知 ................................................. 19
12.2 社区资源................................................................ 19
12.3 商标....................................................................... 19
12.4 静电放电警告......................................................... 19
12.5 术语表 ................................................................... 19
13 机械、封装和可订购信息....................................... 19
8
4 修订历史记录
Changes from Original (January 2015) to Revision A
Page
•
•
•
添加了 TPL5x1x 系列纳瓦级计时器表 ................................................................................................................................... 3
Changed TADC and RD equations in the Quantization Error section..................................................................................... 14
添加了接收文档更新通知部分 ............................................................................................................................................... 19
2
版权 © 2015–2018, Texas Instruments Incorporated
TPL5010
www.ti.com.cn
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
5 器件比较表
TPL5x1x 系列纳瓦级计时器
输出
器件编号
TPL5010
TPL5010Q
特殊 特性
评分
目录
汽车
低功耗计时器、看门狗功能
低功耗计时器、看门狗功能
高电平有效
高电平有效
低功耗计时器、电源门控
MOS 驱动器
TPL5111
TPL5110
高电平有效
低电平有效
目录
目录
低功耗计时器、电源门控
MOS 驱动器
Copyright © 2015–2018, Texas Instruments Incorporated
3
TPL5010
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
www.ti.com.cn
6 Pin Configuration and Functions
DDC Package
6-Lead SOT-23
Top View
TPL5010
1
2
3
VDD
RSTn
WAKE
DONE
6
5
4
GND
DELAY/
M_RST
Pin Functions
PIN
TYPE(1)
DESCRIPTION
APPLICATION INFORMATION
NO.
1
NAME
VDD
P
G
I
Supply voltage
Ground
2
GND
3
DELAY/
M_RST
Time Interval set and Manual Reset Resistance between this pin and GND is used to
select the time interval. The reset switch is also
connected to this pin.
4
5
6
DONE
WAKE
RSTn
I
Logic Input for watchdog
functionality
Digital signal driven by the µC to indicate successful
processing of the WAKE signal.
O
O
Timer output signal generated every Digital pulsed signal to wake up the µC at the end of
tIP period.
the programmed time interval.
Reset Output (open drain output)
Digital signal to RESET the µC, pullup resistance is
required
(1) G= Ground, P= Power, O= Output, I= Input.
4
Copyright © 2015–2018, Texas Instruments Incorporated
TPL5010
www.ti.com.cn
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
7 Specifications
7.1 Absolute Maximum Ratings(1)
MIN
–0.3
–0.3
–5
MAX
6
UNIT
V
Supply Voltage (VDD-GND)
Input Voltage at any pin(2)
Input Current on any pin
Junction Temperature, TJ(3)
Storage Temperature, Tstg
VDD + 0.3
+5
V
mA
°C
150
–65
150
°C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) The voltage between any two pins should not exceed 6V.
(3) The maximum power dissipation is a function of TJ(MAX), θJA, and the ambient temperature, TA. The maximum allowable power
dissipation at any ambient temperature is PDMAX = (TJ(MAX) - TA)/ θJA. All numbers apply for packages soldered directly onto a
printed-circuit board (PCB).
7.2 ESD Ratings
VALUE
±1000
±250
UNIT
Human Body Model, per ANSI/ESDA/JEDEC JS-001(1)
Charged-device model (CDM), per JEDEC specification JESD22-101(2)
V(ESD)
Electrostatic discharge
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Ratings
MIN
MAX
5.5
UNIT
V
Supply Voltage (VDD-GND)
Temperature
1.8
–40
105
°C
7.4 Thermal Information
TPL5010
THERMAL METRIC(1)
DDC (SOT-23)
UNIT
6 PINS
163
26
RθJA
Junction-to-ambient thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
57
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
7.5
ψJB
57
RθJC(bot)
N/A
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report (SPRA953).
Copyright © 2015–2018, Texas Instruments Incorporated
5
TPL5010
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
www.ti.com.cn
7.5 Electrical Characteristics(1)
Specifications are for TA= 25°C, VDD-GND = 2.5 V, unless otherwise stated.
PARAMETER
TEST CONDITIONS
MIN(2)
TYP(3)
MAX(2) UNIT
POWER SUPPLY
IDD
Supply current(4)
Operation mode
35
50
nA
µA
Digital conversion of external
resistance (Rext)
200
400
TIMER
tIP
Time Interval Period
1650 selectable
Time Intervals
Minimum time
interval
100
ms
s
Maximum time
interval
7200
Time Interval Setting Accuracy(5)
Excluding the precision of Rext
±0.6%
±25
Timer Interval Setting Accuracy over 1.8 V ≤ VDD ≤ 5.5 V
ppm/V
supply voltage
tOSC
Oscillator Accuracy
–0.5%
0.5%
Oscillator Accuracy over
temperature(6)
–40°C ≤ TA ≤ 105°C
1.8 V ≤ VDD ≤ 5.5 V
±100
±0.4
±400 ppm/°C
Oscillator Accuracy over supply
voltage
%/V
Oscillator Accuracy over life time(7)
0.24%
(6)
tDONE
tRSTn
DONE Pulse width
100
ns
ms
ms
RSTn Pulse width
WAKE Pulse width
Time to convert Rext
320
20
tWAKE
t_Rext
100
120
ms
DIGITAL LOGIC LEVELS
VIH
VIL
Logic High Threshold DONE pin
0.7 × VDD
V
V
Logic Low Threshold DONE pin
0.3 ×
VDD
Iout = 100 µA
Iout = 1 mA
VDD – 0.3
VDD – 0.7
V
V
VOH
VOL
Logic output High Level WAKE pin
Logic output Low Level WAKE pin
Iout = -100 µA
Iout = –1 mA
IOL = –1 mA
VOHRSTn = VDD
0.3
0.7
0.3
V
V
VOLRSTn
IOHRSTn
VIHM_RST
RSTn Logic output Low Level
RSTn High Level output current
V
1
nA
V
Logic High Threshold
DELAY/M_RST pin
1.5
(1) Electrical Characteristics values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in
very limited self-heating of the device such that TJ = TA. No specification of parametric performance is indicated in the electrical tables
under conditions of internal self-heating where TJ > TA. Absolute Maximum Ratings indicate junction temperature limits beyond which
the device may be permanently degraded, either mechanically or electrically.
(2) Limits are specified by testing, design, or statistical analysis at 25°C. Limits over the operating temperature range are specified through
correlations using statistical quality control (SQC) method.
(3) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not specified on shipped
production material.
(4) The supply current excludes load and pullup resistor current. Input pins are at GND or VDD.
(5) The accuracy for time interval settings below 1 second is ±100 ms.
(6) This parameter is specified by design and/or characterization and is not tested in production.
(7) Operational life time test procedure equivalent to 10 years.
6
Copyright © 2015–2018, Texas Instruments Incorporated
TPL5010
www.ti.com.cn
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
7.6 Timing Requirements
MIN(1) NOM(2) MAX(1) UNIT
(3)
trRSTn
tfRSTn
trWAKE
tfWAKE
Rise Time RSTn
Fall Time RSTn
Capacitive load 50 pF, Rpullup 100 kΩ
Capacitive load 50 pF, Rpullup 100 kΩ
Capacitive load 50 pF
11
50
µs
ns
ns
ns
ns
(3)
(3)
Rise Time WAKE
Fall Time WAKE
50
(3)
Capacitive load 50 pF
Minimum delay(4)
50
100
DONE to RSTn or WAKE to DONE
delay
tDDONE
tIP-
(4)
Maximum delay
ms
20ms
tM_RST
tDB
Valid Manual Reset
Observation time 30 ms
20
ms
ms
De-bounce Manual Reset
20
(1) Limits are specified by testing, design, or statistical analysis at 25°C. Limits over the operating temperature range are specified through
correlations using statistical quality control (SQC) method.
(2) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not specified on shipped
production material.
(3) This parameter is specified by design and/or characterization and is not tested in production.
(4) In case of RSTn from its falling edge, or in case of WAKE from its rising edge.
VDD
ttWAKE
t
trWAKE
WAKE
DONE
RSTn
ttIPt
ttDDONEt
tfWAKE
tDONE
ttRSTn+ tIP
t
trRSTn
ttRSTn+tDB
t
ttRSTnt
ttR_EXT + tRSTn
t
tfRSTn
DELAY/
M_RST
ttM_RST
Figure 1. TPL5010 Timing
Copyright © 2015–2018, Texas Instruments Incorporated
7
TPL5010
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
www.ti.com.cn
7.7 Typical Characteristics
80
80
70
60
50
40
30
20
TA= -40°C
TA= 25°C
TA= 70°C
VDD= 1.8V
VDD= 2.5V
VDD= 3.3V
VDD= 5.5V
70
60
50
40
30
20
TA= 105°C
1.5
1.9
2.3
2.7
3.1
3.5
3.9
4.3
4.7
5.1
5.5
5.5
1
-40
-25
-10
5
20
35
50
65
80
95
110
Supply Voltage (V)
Temperature (°C)
Figure 2. IDD vs. VDD
Figure 3. IDD vs. Temperature
2
1.5
1
2
1.5
1
TA= -40°C
TA= 25°C
TA= 70°C
TA= 105°C
VDD= 1.8V
VDD= 2.5V
VDD= 3.3V
VDD= 5.5V
0.5
0
0.5
0
-0.5
-1
-0.5
-1
1.5
1.9
2.3
2.7
3.1
3.5
3.9
4.3
4.7
5.1
-40
-25
-10
5
20
35
50
65
80
95
110
Supply Voltage (V)
Temperature (°C)
Figure 4. Oscillator Accuracy vs. VDD
Figure 5. Oscillator Accuracy vs. Temperature
1000
100
10
40%
POR
REXT READING
35%
30%
25%
20%
15%
10%
5%
1
TIMER MODE
0.1
0.01
0
0
0.1
0.2
0.3
0.4
0.5
Time (s)
0.6
0.7
0.8
0.9
-1
-0.8
-0.6
-0.4
-0.2
0
0.2
0.4
0.6
0.8
Accuracy (%)
number of
1s < tIP ≤ 7200s
observations
>20000
Figure 7. Time Interval Setting Accuracy
Figure 6. IDD vs. Time
8
Copyright © 2015–2018, Texas Instruments Incorporated
TPL5010
www.ti.com.cn
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
8 Detailed Description
8.1 Overview
The TPL5010 is a system wake-up timer with a watchdog feature designed for low-power applications. The
TPL5010 can be used in interrupt-driven applications and provides selectable timing from 100 ms to 7200 s.
8.2 Functional Block Diagram
VDD
RSTn
LOW FREQUENCY
OSCILLATOR
FREQUENCY
DIVIDER
LOGIC
CONTROL
WAKE
DONE
DELAY/
M_RST
DECODER
&
MANUAL RESET
DETECTOR
GND
8.3 Feature Description
The DONE, WAKE and RSTn signals are used to implement the watchdog function. The TPL5010 is
programmed to issue a periodic WAKE pulse to a µC which is in sleep or standby mode. After receiving the
WAKE pulse, the µC must issue a DONE signal to the TPL5010 at least 20 ms before the rising edge of the next
WAKE pulse. If the DONE signal is not asserted, the TPL5010 asserts the RSTn signal to reset the µC. A
manual reset function is realized by momentarily pulling the DELAY/M_RST pin to VDD.
ttIPt
ttIPt
WAKE
DONE
RSTn
MISSED
DONE
ttRSTn+ tIPt
DELAY/
M_RST
Figure 8. Watchdog
8.3.1 WAKE
The WAKE pulse is sent out from the TPL5010 when the programmed time interval starts (except at the
beginning of the first cycle or if in the previous interval the DONE has not been received).
This signal is normally low.
8.3.2 DONE
The DONE pin is driven by a µC to signal successful processing of the WAKE signal. The TPL5010 recognizes a
valid DONE signal as a low to high transition. If two or more DONE signals are received within the time interval,
only the first DONE signal is processed.
The DONE signal resets the counter of the watchdog only. If the DONE signal is received when the WAKE is still
high, the WAKE will go low as soon as the DONE is recognized.
Copyright © 2015–2018, Texas Instruments Incorporated
9
TPL5010
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
www.ti.com.cn
Feature Description (continued)
8.3.3 RSTn
To implement the reset interface between the TPL5010 and the µC a pullup resistance is required. 100 KΩ is
recommended to minimize current.
During the POR and the reading of the REXT, the RSTn signal is LOW.
RSTn is asserted (LOW) for either one of the following conditions:
1. If the DELAY/M_RST pin is high for at least two consecutive cycles of the internal oscillator (approximately
20 ms).
2. At the beginning of a new time interval if DONE is not received at least 20 ms before the next WAKE rising
edge (see Figure 8).
8.4 Device Functional Modes
8.4.1 Start-Up
During start-up after POR, the TPL5010 executes a one-time measurement of the resistance attached to the
DELAY/M_RST pin to determine the desired time interval for WAKE. This measurement interval is tR_EXT. During
this measurement, a constant current is temporarily flowing into REXT
.
ttR_EXT + tRSTn + tIPt
ttIPt
WAKE
DONE
RSTn
DELAY/
M_RST
RESISTANCE
POR
READING
Figure 9. Start-Up
8.4.2 Normal Operating Mode
During normal operating mode, the TPL5010 asserts periodic WAKE pulses in response to valid DONE pulses
from the µC. If either a manual reset is applied (logic HIGH on DELAY/M_RST pin), or the µC does not issue a
DONE pulse within the required time, the TPL5010 asserts the RSTn signal to the µC and restarts its internal
counters. See Figure 8 and Figure 10 .
8.5 Programming
8.5.1 Configuring the WAKE Interval With the DELAY/M_RST Pin
The time interval between two adjacent WAKE pulses (rising edges) is selectable through an external resistance
(REXT) between the DELAY/M_RST pin and ground. The value of the resistance REXT is converted one time after
POR. The allowable range of REXT is 500 Ω to 170 kΩ. At least a 1% precision resistance is recommended. See
section Timer Interval Selection Using External Resistance on how to set the WAKE pulse interval using REXT
.
The time between two adjacent RESET signals (falling edges), or between a RESET (falling edge) and a WAKE
(rising edge), is given by the sum of the programmed time interval and the tRSTn (reset pulse width).
10
Copyright © 2015–2018, Texas Instruments Incorporated
TPL5010
www.ti.com.cn
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
Programming (continued)
8.5.2 Manual Reset
If VDD is connected to the DELAY/M_RST pin, the TPL5010 recognizes this as a manual reset condition. In this
case, the time interval is not set. If the manual reset is asserted during the POR or during the reading procedure,
the reading procedure is aborted and is restarted as soon as the manual reset switch is released. A pulse on the
DELAY/M_RST pin is recognized as a valid manual reset only if it lasts at least 20 ms (observation time is 30
ms).
A valid manual reset resets all the counters inside the TPL5010. The counters restart only when the high digital
voltage at DELAY/M_RST is removed and the next tRSTn is elapsed.
ttIPt
WAKE
DONE
ttRSTn+ tIPt
RSTn
ANY RESET
ttM_RST
t
ttDB
t
ttM_RSTt
DELAY/
M_RST
VALID M_RST
NOT VALID M_RST
Figure 10. Manual Reset
8.5.2.1 DELAY/M_RST
A resistance in the range between 500 Ω and 170 kΩ needs to be connected to select a valid time interval. At the
POR and during the reading of the resistance the DELAY/M_RST is connected to an analog signal chain though
a mux. After the reading of the resistance the analog circuit is switched off and the DELAY/RST is connected to
a digital circuit.
The manual reset detection is supported with a de-bounce feature which makes the TPL5010 insensitive to the
glitches on the DELAY/M_RST pin. When a valid manual reset signal is asserted on the DELAY/M_RST pin, the
RSTn signal is asserted LOW after a delay of tM_RST. It remains LOW after a valid manual reset is asserted + tDB
+ tRSTn. Due to the asynchronous nature of the manual reset signal and its arbitrary duration, the LOW status of
the RSTn signal maybe affected by an uncertainty of about ±5 ms.
A valid manual reset puts all the digital output signals at their default values:
•
•
WAKE = LOW
RSTn = asserted LOW
8.5.2.2 Circuitry
The manual reset may be implemented using a switch (momentary mechanical action). The TPL5010 offers two
possible approaches according to the power consumption constraints of the application.
Copyright © 2015–2018, Texas Instruments Incorporated
11
TPL5010
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
www.ti.com.cn
Programming (continued)
µC
VOUT
VIN
Rp
TPL5010
RSTn
VDD
VDD
GND
RSTn
GPIO
GPIO
Battery
POWER MANAGEMENT
WAKE
DONE
DELAY/
M_RST
REXT
GND
GND
Figure 11. Manual Reset With SPST Switch
For use cases that do not require the lowest power consumption, using a single-pole single-throw switch may
offer a lower-cost solution. The DELAY/M_RST pin may be directly connected to VDD with REXT in the circuit.
The current drawn from the supply voltage during the reset is given by VDD/REXT
.
µC
VOUT
Rp
TPL5010
RSTn
VIN
VDD
VDD
GND
RSTn
GPIO
GPIO
Battery
POWER MANAGEMENT
GND
WAKE
DONE
DELAY/
M_RST
REXT
GND
Figure 12. Manual Reset With SPDT Switch
The reset function may also be asserted by switching DELAY/M_RST from REXT to VDD using a single-pole
double-throw switch, which will provide a lower power solution for the manual reset, because no current flows.
8.5.3 Timer Interval Selection Using External Resistance
To set the time interval, the external resistance REXT is selected according to Equation 1:
- b + b 2 - 4a
2a
(
c -100 T
)
≈
∆
’
÷
REXT =100
∆
«
÷
◊
where
•
•
•
T is the desired time interval in seconds.
REXT is the resistance value to use in Ω.
a, b, and c are coefficients depending on the range of the time interval.
(1)
12
Copyright © 2015–2018, Texas Instruments Incorporated
TPL5010
www.ti.com.cn
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
Programming (continued)
Table 1. Coefficients for Equation 1
Time interval
Range (s)
SET
a
b
c
1
2
3
4
5
1 < T ≤ 5
0.2253
–0.1284
0.1972
0.2617
0.3177
–20.7654
46.9861
570.5679
–2651.8889
692.1201
5 < T ≤ 10
10 < T ≤ 100
100 < T ≤ 1000
T > 1000
–19.3450
–56.2407
–136.2571
5957.7934
34522.4680
EXAMPLE
Required time interval: 8 s
The coefficient set to be selected is the number 2. The formula becomes Equation 2.
2
≈
’
46.9861- 46.9861 +4*0.1284
(
-2561.8889-100*8
)
∆
÷
REXT =100
∆
«
÷
◊
2*0.1284
(2)
The resistance value is 10.18 kΩ.
Table 2 and Table 3 contain example values of tIP and their corresponding value of REXT
.
Table 2. First 9 Time Intervals
Parallel of Two 1% Tolerance
tIP (ms)
Resistance (Ω)
Closest Real Value (Ω)
Resistors, (kΩ)
100
200
300
400
500
600
700
800
900
500
500
1.0 // 1.0
-
1000
1500
2000
2500
3000
3500
4000
4500
1000
1500
2000
2500
3000
3500
4000
4501
2.43 // 3.92
-
4.42 // 5.76
5.36 // 6.81
4.75 // 13.5
6.19 // 11.3
6.19 // 16.5
Table 3. Most Common Time Intervals Between 1s to 2h
Closest Real Value
Parallel of Two 1% Tolerance Resistors,
tIP
Calculated Resistance (kΩ)
(kΩ)
(kΩ)
1s
2s
5.20
6.79
5.202
6.788
7.15 // 19.1
12.4 // 15.0
12.7// 19.1
14.7 // 19.1
16.5 // 19.1
18.2 // 18.7
19.1 // 19.6
11.5 // 8.87
17.8 // 26.7
15.0 // 44.2
16.9 // 97.6
32.4 // 34.8
22.6 // 110.0
28.7 // 66.5
3s
7.64
7.628
4s
8.30
8.306
5s
8.85
8.852
6s
9.27
9.223
7s
9.71
9.673
8s
10.18
10.68
11.20
14.41
16.78
18.75
20.047
10.180
10.68
9s
10s
20s
30s
40s
50s
11.199
14.405
16.778
18.748
20.047
Copyright © 2015–2018, Texas Instruments Incorporated
13
TPL5010
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
www.ti.com.cn
Table 3. Most Common Time Intervals Between 1s to 2h (continued)
Closest Real Value
Parallel of Two 1% Tolerance Resistors,
tIP
Calculated Resistance (kΩ)
(kΩ)
(kΩ)
1min
2min
3min
4min
5min
6min
7min
8min
9min
10min
20min
30min
40min
50min
1h
22.02
29.35
34.73
39.11
42.90
46.29
49.38
52.24
54.92
57.44
77.57
92.43
104.67
115.33
124.91
149.39
170.00
22.021
29.349
34.729
39.097
42.887
46.301
49.392
52.224
54.902
57.437
77.579
92.233
104.625
115.331
124.856
149.398
170.00
40.2 // 48.7
35.7 // 165.0
63.4 // 76.8
63.4 // 102.0
54.9 // 196.0
75.0 // 121.0
97.6 // 100.0
88.7 // 127.0
86.6 // 150.0
107.0 // 124.0
140.0 // 174.0
182.0 // 187.0
130.0 // 536.00
150.0 // 499.00
221.0 // 287.00
165.0 // 1580.0
340.0 // 340.0
1h30min
2h
8.5.4 Quantization Error
The TPL5010 can generate 1650 discrete timer intervals in the range of 100 ms to 7200 s. The first 9 intervals
are multiples of 100 ms. The remaining 1641 intervals cover the range between 1 s to 7200 s. Because they are
discrete intervals, there is a quantization error associated with each value.
The quantization error can be evaluated according to Equation 3:
(
TDESIRED -TADC
)
Err =100
TDESIRED
where
1
é
ù
TADC = INT
aR2 + bR + c
(
)
D
D
ê
ú
100
ë
û
•
•
REXT
100
RD
=
(3)
REXT is the resistance calculated with Equation 1 and a, b, c are the coefficients of the equation listed in Table 1.
8.5.5 Error Due to Real External Resistance
REXT is a theoretical value and may not be available in standard commercial resistor values. It is possible to
closely approach the theoretical REXT using two or more standard values in parallel. However, standard values
are characterized by a certain tolerance. This tolerance will affect the accuracy of the time interval.
The accuracy can be evaluated using the following procedure:
1. Evaluate the min and max values of REXT (REXT_MIN, REXT_MAX with Equation 1 using the selected commercial
resistance values and their tolerances.
2. Evaluate the time intervals (TADC_MIN[REXT_MIN], TADC_MAX[REXT_MAX]) with the TADC equation mentioned in
Equation 3.
3. Find the errors using Equation 3 with TADC_MIN, TADC_MAX
.
The results of the formula indicate the accuracy of the time interval.
14
Copyright © 2015–2018, Texas Instruments Incorporated
TPL5010
www.ti.com.cn
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
The example below illustrates the procedure.
•
•
Desired time interval, T_desired = 600 s,
Required REXT from Equation 1, REXT= 57.44 kΩ.
From Table 3 REXT can be built with a parallel combination of two commercial values with 1% tolerance: R1 =
107 kΩ, R2 = 124 kΩ. The uncertainty of the equivalent parallel resistance can be found using Equation 4:
2
2
u
u
R2
≈
∆
R1 ’ ≈
’
÷
uR =R//
+
÷ ∆
//
R1
R2
«
◊ «
◊
where
•
uRn (n=1,2) represent the uncertainty of a resistance (see Equation 5)
(4)
(5)
SPACER
Tolerance
uR =Rn
n
3
The uncertainty of the parallel resistance is 0.82%, which means the value of REXT may range between REXT_MIN
= 56.96 kΩ and REXT_MAX = 57.90 kΩ.
Using these value of REXT, the digitized timer intervals calculated by TADC equation mentioned in Equation 3 are
respectively TADC_MIN = 586.85 s and TADC_MAX = 611.3 s, giving an error range of –1.88% / +2.19%. The
asymmetry of the error range is due to the quadratic transfer function of the resistance digitizer.
Copyright © 2015–2018, Texas Instruments Incorporated
15
TPL5010
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
www.ti.com.cn
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
In battery-powered applications, one design constraint is the need for low current consumption. The TPL5010 is
designed for applications where there is a need to monitor environmental conditions at a fixed time interval. Often
in these applications a watchdog or other internal timer in a µC is used to implement a wake-up function. Using
the TPL5010 to implement the watchdog function will consume only tens of nA, significantly improving the power
consumption of the system.
9.2 Typical Application
The TPL5010 can be used in conjunction with environment sensors to build a low-power environment data-
logger, such as an air quality data-logger. In this application, due to the monitored phenomena, the µC and the
front end of the sensor spend most of the time in the idle state, waiting for the next logging interval, usually a few
hundred of milliseconds. Figure 13 shows a data logging application based on a µC and a front end for a gas
sensor based on the LMP91000.
VOLTAGE
REFERENCE
VIN
VOUT
GND
µC
LMP91000
Rp
100k
VOUT
VIN
Rp
100k
Rp
100k
VDD
SDA
VDD
SCL
SDA
VREF
CE
TPL5010
RSTn
+
VDD
GND
RST
Lithium
ion battery
CE
POWER MANAGEMENT
GND
WAKE
DONE
GPIO
GPIO
SCL
RE
RE
WE
-
DELAY/
M_RST
ADC
GND
GPIO
GPIO
VOUT
GND
WE
GAS
SENSOR
MENB
GPIO
GPIO
Button
Temp 29°C
CO 0PPM
Button
Button
TIME xx:xx
Date xx/xx/xxxx
DISPLAY
KEYBOARD
Figure 13. Data-Logger
9.2.1 Design Requirements
The design is driven by the low-current consumption constraint. The data are usually acquired on a rate that
ranges between 1 s and 10 s. The highest necessity is the maximization of the battery life. The TPL5010 helps
achieve that goal because it allows putting the µC in its lowest power mode. The TPL5010 will take care of the
watchdog and the timing.
16
Copyright © 2015–2018, Texas Instruments Incorporated
TPL5010
www.ti.com.cn
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
Typical Application (continued)
9.2.2 Detailed Design Procedure
When the main constraint is the battery life, the selection of a low power voltage reference, the µC, and the
display is mandatory. The first step in the design is the calculation of the power consumption of the devices in
their different mode of operations. For instance, the LMP91000 burns most of the power when in gas
measurement mode, then, according to the connected gas sensor, it has two idle states (standby and deep
sleep). The same is true for the µC, such as one of the MSP430 family, which can be placed in one of its lower
power modes, such as LMP3.5 or LMP4.5. In this case, the TPL5010 can be used to implement the watchdog
and wake-up timing functions.
After the power budget calculation, it is possible to select the appropriate time interval which satisfies the
application constraints and maximize the life of the battery.
9.2.3 Application Curve
Without TPL5010
With TPL5010
Time
Figure 14. Effect of TPL5010 on Current Consumption
Copyright © 2015–2018, Texas Instruments Incorporated
17
TPL5010
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
www.ti.com.cn
10 Power Supply Recommendations
The TPL5010 requires a voltage supply within 1.8 V and 5.5 V. A multilayer ceramic bypass X7R capacitor of 0.1
μF between VDD and GND pin is recommended.
11 Layout
11.1 Layout Guidelines
The DELAY/M_RST pin is sensitive to parasitic capacitance. TI suggests that the traces connecting the
resistance on this pin to GROUND be kept as short as possible to minimize parasitic capacitance. This
capacitance can affect the initial set up of the time interval. Signal integrity on the WAKE and RSTn pins is also
improved by keeping the trace length between the TPL5010 and the µC short to reduce the parasitic
capacitance.
11.2 Layout Example
Figure 15. Layout
18
版权 © 2015–2018, Texas Instruments Incorporated
TPL5010
www.ti.com.cn
ZHCSEK6A –JANUARY 2015–REVISED SEPTEMBER 2018
12 器件和文档支持
12.1 接收文档更新通知
要接收文档更新通知,请导航至 TI.com.cn 上的器件产品文件夹。单击右上角的通知我 进行注册,即可每周接收产
品信息更改摘要。有关更改的详细信息,请查看任何已修订文档中包含的修订历史记录。
12.2 社区资源
下列链接提供到 TI 社区资源的连接。链接的内容由各个分销商“按照原样”提供。这些内容并不构成 TI 技术规范,
并且不一定反映 TI 的观点;请参阅 TI 的 《使用条款》。
TI E2E™ 在线社区 TI 的工程师对工程师 (E2E) 社区。此社区的创建目的在于促进工程师之间的协作。在
e2e.ti.com 中,您可以咨询问题、分享知识、拓展思路并与同行工程师一道帮助解决问题。
设计支持
TI 参考设计支持 可帮助您快速查找有帮助的 E2E 论坛、设计支持工具以及技术支持的联系信息。
12.3 商标
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.4 静电放电警告
ESD 可能会损坏该集成电路。德州仪器 (TI) 建议通过适当的预防措施处理所有集成电路。如果不遵守正确的处理措施和安装程序 , 可
能会损坏集成电路。
ESD 的损坏小至导致微小的性能降级 , 大至整个器件故障。 精密的集成电路可能更容易受到损坏 , 这是因为非常细微的参数更改都可
能会导致器件与其发布的规格不相符。
12.5 术语表
SLYZ022 — TI 术语表。
这份术语表列出并解释术语、缩写和定义。
13 机械、封装和可订购信息
以下页面包含机械、封装和可订购信息。这些信息是指定器件的最新可用数据。数据如有变更,恕不另行通知,且
不会对此文档进行修订。如需获取此产品说明书的浏览器版本,请查阅左侧的导航栏。
版权 © 2015–2018, Texas Instruments Incorporated
19
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TPL5010DDCR
TPL5010DDCT
ACTIVE SOT-23-THIN
ACTIVE SOT-23-THIN
DDC
DDC
6
6
3000 RoHS & Green
250 RoHS & Green
NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 105
-40 to 105
ZAKX
ZAKX
NIPDAU
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jun-2022
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPL5010DDCR
TPL5010DDCT
TPL5010DDCT
SOT-23-
THIN
DDC
DDC
DDC
6
6
6
3000
250
178.0
178.0
180.0
8.4
8.4
8.4
3.2
3.2
3.1
3.2
1.4
1.4
1.1
4.0
4.0
4.0
8.0
8.0
8.0
Q3
Q3
Q3
SOT-23-
THIN
3.2
SOT-23-
THIN
250
3.05
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Jun-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPL5010DDCR
TPL5010DDCT
TPL5010DDCT
SOT-23-THIN
SOT-23-THIN
SOT-23-THIN
DDC
DDC
DDC
6
6
6
3000
250
208.0
208.0
183.0
191.0
191.0
183.0
35.0
35.0
20.0
250
Pack Materials-Page 2
PACKAGE OUTLINE
DDC0006A
SOT-23 - 1.1 max height
S
C
A
L
E
4
.
0
0
0
SMALL OUTLINE TRANSISTOR
3.05
2.55
1.1
0.7
1.75
1.45
0.1 C
B
A
PIN 1
INDEX AREA
1
6
4X 0.95
1.9
3.05
2.75
4
3
0.5
0.3
0.1
6X
TYP
0.0
0.2
C A B
C
0 -8 TYP
0.25
GAGE PLANE
SEATING PLANE
0.20
0.12
TYP
0.6
0.3
TYP
4214841/C 04/2022
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Reference JEDEC MO-193.
www.ti.com
EXAMPLE BOARD LAYOUT
DDC0006A
SOT-23 - 1.1 max height
SMALL OUTLINE TRANSISTOR
SYMM
6X (1.1)
1
6
6X (0.6)
SYMM
4X (0.95)
4
3
(R0.05) TYP
(2.7)
LAND PATTERN EXAMPLE
EXPLOSED METAL SHOWN
SCALE:15X
METAL UNDER
SOLDER MASK
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL
EXPOSED METAL
EXPOSED METAL
0.07 MIN
ARROUND
0.07 MAX
ARROUND
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
SOLDERMASK DETAILS
4214841/C 04/2022
NOTES: (continued)
4. Publication IPC-7351 may have alternate designs.
5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DDC0006A
SOT-23 - 1.1 max height
SMALL OUTLINE TRANSISTOR
SYMM
6X (1.1)
1
6
6X (0.6)
SYMM
4X(0.95)
4
3
(R0.05) TYP
(2.7)
SOLDER PASTE EXAMPLE
BASED ON 0.125 THICK STENCIL
SCALE:15X
4214841/C 04/2022
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
7. Board assembly site may have different recommendations for stencil design.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022,德州仪器 (TI) 公司
相关型号:
©2020 ICPDF网 联系我们和版权申明