TPS3710-Q1 [TI]
汽车类宽输入电压 (18V) 电压检测器;型号: | TPS3710-Q1 |
厂家: | TEXAS INSTRUMENTS |
描述: | 汽车类宽输入电压 (18V) 电压检测器 |
文件: | 总22页 (文件大小:892K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
TPS3710-Q1
SBVS341 –JULY 2017
TPS3710-Q1 Wide VIN Voltage Detector
1 Features
3 Description
The TPS3710-Q1 wide-supply voltage detector
operates over a 1.8-V to 18-V range. The device has
a high-accuracy comparator with an internal 400-mV
reference and an open-drain output rated to 18 V for
precision voltage detection. The monitored voltage
can be set with the use of external resistors.
1
•
•
Qualified for Automotive Applications
AEC-Q100 Qualified With the Following Results:
–
Device Temperature Grade 1: -40°C to 125°C
Ambient Operating Temperature Range
–
–
Device HBM ESD Classification Level 2
Device CDM ESD Classification Level C6
The OUT pin is driven low when the voltage at the
SENSE pin drops below (VIT–), and goes high when
the voltage returns above the respective threshold
(VIT+). The comparator in the TPS3710-Q1 includes
built-in hysteresis for filtering to reject brief glitches,
thereby ensuring stable output operation without false
triggering.
•
•
•
Wide Supply Voltage Range: 1.8 V to 18 V
Adjustable Threshold: Down to 400 mV
High Threshold Accuracy:
–
–
1.0% Over Temperature
0.25% (Typical)
The TPS3710-Q1 is available in a 1.5-mm × 1.5-mm
6-pin WSON package, and is specified over the
junction temperature range of –40°C to +125°C.
•
•
•
•
•
Low Quiescent Current: 5.5 µA (Typical)
Open-Drain Output
Internal Hysteresis: 5.5 mV (Typical)
Temperature Range: –40°C to +125°C
Packages:
(1)
Device Information
PART NUMBER
PACKAGE
BODY SIZE (NOM)
TPS3710-Q1
WSON (6)
1.50 mm × 1.50 mm
–
1.5-mm × 1.5-mm WSON-6
(1) For all available packages, see the package option addendum
at the end of the data sheet.
2 Applications
•
•
•
Automotive Systems
Embedded Computing Modules
DSP, Microcontroller, or Microprocessor
Applications
•
•
•
Notebook and Desktop Computers
Portable- and Battery-Powered Products
FPGA and ASIC Applications
Rising Input Threshold Voltage (VIT+) vs
Temperature
Simplified Schematic
401
VMON
1.8 V to 18 V
VDD = 1.8 V
VDD = 5 V
0.01 ꢀF
VDD = 12 V
VDD = 18 V
400.6
VPULLUP
Up to 18 V
400.2
R1
VDD
SENSE
RP
To a reset or enable
input of the system.
399.8
399.4
399
OUT
R2
GND
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (èC)
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TPS3710-Q1
SBVS341 –JULY 2017
www.ti.com
Table of Contents
7.4 Device Functional Modes........................................ 10
Application and Implementation ........................ 11
8.1 Application Information............................................ 11
8.2 Typical Application .................................................. 13
8.3 Do's and Don'ts....................................................... 14
Power-Supply Recommendations...................... 15
1
2
3
4
5
6
Features.................................................................. 1
8
Applications ........................................................... 1
Description ............................................................. 1
Revision History..................................................... 2
Pin Configuration and Functions......................... 3
Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 ESD Ratings ............................................................ 4
6.3 Recommended Operating Conditions....................... 4
6.4 Thermal Information.................................................. 4
6.5 Electrical Characteristics........................................... 5
6.6 Timing Requirements................................................ 6
6.7 Switching Characteristics.......................................... 6
6.8 Typical Characteristics.............................................. 7
Detailed Description .............................................. 9
7.1 Overview ................................................................... 9
7.2 Functional Block Diagram ......................................... 9
7.3 Feature Description................................................. 10
9
10 Layout................................................................... 15
10.1 Layout Guidelines ................................................. 15
10.2 Layout Example .................................................... 15
11 Device and Documentation Support ................. 16
11.1 Device Support...................................................... 16
11.2 Documentation Support ........................................ 16
11.3 Receiving Notification of Documentation Updates 16
11.4 Community Resources.......................................... 16
11.5 Trademarks........................................................... 16
11.6 Electrostatic Discharge Caution............................ 16
11.7 Glossary................................................................ 16
7
12 Mechanical, Packaging, and Orderable
Information ........................................................... 16
4 Revision History
DATE
REVISION
NOTES
July 2017
*
Initial release
2
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
Product Folder Links: TPS3710-Q1
TPS3710-Q1
www.ti.com
SBVS341 –JULY 2017
5 Pin Configuration and Functions
DSE Package
6-Pin WSON
Top View
GND
VDD
1
2
6
5
4
OUT
GND
GND
3
SENSE
Pin Functions
PIN
I/O
DESCRIPTION
NAME
GND
DSE
1, 3, 5
—
O
Connect all three pins to ground.
SENSE comparator open-drain output. OUT is driven low when the voltage at this comparator is
below (VIT-). The output goes high when the sense voltage returns above the respective
threshold (VIT+).
OUT
6
This pin is connected to the voltage to be monitored with the use of an external resistor divider.
When the voltage at this pin drops below the threshold voltage (VIT-), OUT is driven low.
SENSE
VDD
4
2
I
I
Supply voltage input. Connect a 1.8-V to 18-V supply to VDD to power the device. Good analog
design practice is to place a 0.1-µF ceramic capacitor close to this pin.
Copyright © 2017, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: TPS3710-Q1
TPS3710-Q1
SBVS341 –JULY 2017
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating temperature range (unless otherwise noted)(1)
MIN
–0.3
–0.3
–0.3
MAX
20
UNIT
VDD
Voltage(2)
OUT
20
V
SENSE
7
Current
OUT (output sink current)
Operating junction, TJ
Storage, Tstg
40
mA
°C
–40
–65
125
150
Temperature
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to network ground pin.
6.2 ESD Ratings
VALUE
±2500
±1000
UNIT
Human-body model (HBM), per AEC Q100-002(1)
Charged-device model (CDM), per AEC Q100-011
V(ESD)
Electrostatic discharge
V
(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
6.3 Recommended Operating Conditions
over operating temperature range (unless otherwise noted)
MIN
1.8
0
NOM
MAX UNIT
VDD
VI
Supply voltage
Input voltage
Output voltage
18
6.5
18
V
V
V
SENSE
OUT
VO
0
6.4 Thermal Information
TPS3710-Q1
DSE (WSON)
6 PINS
194.9
(1)
THERMAL METRIC
UNIT
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
Junction-to-top characterization parameter
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
128.9
153.8
ψJT
11.9
ψJB
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
157.4
RθJC(bot)
N/A
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
4
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
Product Folder Links: TPS3710-Q1
TPS3710-Q1
www.ti.com
SBVS341 –JULY 2017
6.5 Electrical Characteristics
Over the operating temperature range of TJ = –40°C to +125°C, and 1.8 V < VDD < 18 V (unless otherwise noted).
Typical values are at TJ = 25°C and VDD = 5 V.
PARAMETER
TEST CONDITIONS
VOLmax = 0.2 V, output sink current = 15 µA
VDD = 1.8 V
MIN
TYP
MAX UNIT
(1)
V(POR)
VIT+
Power-on reset voltage
0.8
404
404
400
400
12
V
396
396
387
387
400
400
Positive-going input threshold voltage
Negative-going input threshold voltage
mV
VDD = 18 V
VDD = 1.8 V
394.5
394.5
5.5
VIT–
Vhys
mV
VDD = 18 V
Hysteresis voltage (hys = VIT+ – VIT–
)
mV
nA
I(SENSE) Input current (at the SENSE pin)
VDD = 1.8 V and 18 V, VI = 6.5 V
VDD = 1.3 V, output sink current = 0.4 mA
VDD = 1.8 V, output sink current = 3 mA
VDD = 5 V, output sink current = 5 mA
VDD = 1.8 V and 18 V, VO = VDD
VDD = 1.8 V, VO = 18 V
VDD = 1.8 V, no load
–25
1
25
250
250
250
300
300
11
VOL
Low-level output voltage
mV
nA
Ilkg(OD)
Open-drain output leakage-current
5.5
6
VDD = 5 V
13
IDD
Supply current
µA
V
VDD = 12 V
6
13
VDD = 18 V
7
13
(2)
UVLO
Undervoltage lockout
VDD falling
1.3
1.7
(1) The lowest supply voltage (VDD) at which output is active; tr(VDD) > 15 µs/V. Below V(POR), the output cannot be determined.
(2) When VDD falls below UVLO, OUT is driven low. The output cannot be determined below V(POR)
.
Copyright © 2017, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: TPS3710-Q1
TPS3710-Q1
SBVS341 –JULY 2017
www.ti.com
6.6 Timing Requirements
over operating temperature range (unless otherwise noted)
MIN
NOM
MAX UNIT
VDD = 5 V, 10-mV input overdrive,
RP = 10 kΩ, VOH = 0.9 × VDD, VOL = 400 mV,
see Figure 1
(1)
(1)
tpd(HL)
High-to-low propagation delay
Low-to-high propagation delay
18
µs
VDD = 5 V, 10-mV input overdrive,
RP = 10 kΩ, VOH = 0.9 × VDD, VOL = 400 mV,
see Figure 1
tpd(LH)
td(start)
29
µs
µs
(2)
Start-up delay
150
(1) High-to-low and low-to-high refers to the transition at the input pin (SENSE).
(2) During power on, VDD must exceed 1.8 V for at least 150 µs before the output is in a correct state.
6.7 Switching Characteristics
over operating temperature range (unless otherwise noted)
PARAMETER
Output rise time
Output fall time
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VDD = 5 V, 10-mV input overdrive,
RP = 10 kΩ, VO = (0.1 to 0.9) × VDD
tr
tf
2.2
µs
VDD = 5 V, 10-mV input overdrive,
RP = 10 kΩ, VO = (0.1 to 0.9) × VDD
0.22
µs
VDD
V(POR)
VIT+
VITœ
VHYS
SENSE
OUT
tpd(LH)
tpd(HL)
tpd(LH)
t d(start)
Figure 1. Timing Diagram
6
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
Product Folder Links: TPS3710-Q1
TPS3710-Q1
www.ti.com
SBVS341 –JULY 2017
6.8 Typical Characteristics
at TJ = 25°C and VDD = 5 V (unless otherwise noted)
401
400.6
400.2
399.8
399.4
399
10
9
VDD = 1.8 V
VDD = 5 V
VDD = 12 V
VDD = 18 V
8
7
6
5
4
3
2
1
0
TJ = -40°C
TJ = 0°C
TJ = +25°C
TJ = +85°C
TJ = +125°C
0
2
4
6
8
10
12
14
16
18
-40 -25 -10
5
20 35 50 65 80 95 110 125
Supply Voltage (V)
Temperature (èC)
Figure 2. Supply Current (IDD) vs Supply Voltage (VDD
)
Figure 3. Rising Input Threshold Voltage (VIT+) vs
Temperature
25
23
21
19
17
15
13
11
9
9
VDD = 1.8 V
VDD = 18 V
8
7
6
5
4
3
VDD = 1.8 V
VDD = 5 V
VDD = 12 V
VDD = 18 V
-40 -25 -10
5
20 35 50 65 80 95 110 125
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (èC)
Temperature (èC)
Figure 5. Propagation Delay vs Temperature
(High-to-Low Transition at Sense)
Figure 4. Hysteresis (Vhys) vs Temperature
30
28
26
24
22
20
18
16
14
16
14
12
10
8
6
4
VDD = 1.8 V
VDD = 18 V
2
0
2.5
-40 -25 -10
5
20 35 50 65 80 95 110 125
4
5.5
7
8.5
10
11.5
13
14.5
Temperature (èC)
Positive-Going Input Threshold Overdrive (%)
SENSE = negative spike below VIT–
Figure 6. Propagation Delay vs Temperature
(Low-to-High Transition at Sense)
Figure 7. Minimum Pulse Width vs
Threshold Overdrive Voltage
Copyright © 2017, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: TPS3710-Q1
TPS3710-Q1
SBVS341 –JULY 2017
www.ti.com
Typical Characteristics (continued)
at TJ = 25°C and VDD = 5 V (unless otherwise noted)
2000
1800
1600
1400
1200
1000
800
12
VDD = 1.8 V
VDD = 5 V
VDD = 18 V
10
8
6
4
600
TJ = -40°C
TJ = 0°C
400
TJ = +25°C
TJ = +85°C
TJ = +125°C
2
0
200
0
0
4
8
12
16
20
24
28
32
36
40
0
4
8
12
16
20
24
28
32
36
40
Output Sink Current (mA)
Output Sink Current (mA)
Figure 9. Output Voltage Low (VOL) vs
Output Sink Current (–40°C)
Figure 8. Supply Current (IDD) vs
Output Sink Current
2000
1800
1600
1400
1200
1000
800
2000
1800
1600
1400
1200
1000
800
VDD = 1.8 V
VDD = 5 V
VDD = 18 V
VDD = 1.8 V
VDD = 5 V
VDD = 18 V
600
600
400
400
200
200
0
0
0
4
8
12
16
20
24
28
32
36
40
0
4
8
12
16
20
24
28
32
36
40
Output Sink Current (mA)
Output Sink Current (mA)
Figure 10. Output Voltage Low (VOL) vs
Output Sink Current (0°C)
Figure 11. Output Voltage Low (VOL) vs
Output Sink Current (25°C)
2000
1800
1600
1400
1200
1000
800
2000
1800
1600
1400
1200
1000
800
VDD = 1.8 V
VDD = 5 V
VDD = 18 V
VDD = 1.8 V
VDD = 5 V
VDD = 18 V
600
600
400
400
200
200
0
0
0
4
8
12
16
20
24
28
32
36
40
0
4
8
12
16
20
24
28
32
36
40
Output Sink Current (mA)
Output Sink Current (mA)
Figure 12. Output Voltage Low (VOL) vs
Output Sink Current (85°C)
Figure 13. Output Voltage Low (VOL) vs
Output Sink Current (125°C)
8
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
Product Folder Links: TPS3710-Q1
TPS3710-Q1
www.ti.com
SBVS341 –JULY 2017
7 Detailed Description
7.1 Overview
The TPS3710-Q1 provides precision voltage detection. The TPS3710-Q1 is a wide-supply voltage range (1.8 V
to 18 V) device with a high-accuracy rising input threshold of 400 mV (1% over temperature) and built-in
hysteresis. The output is also rated to 18 V, and can sink up to 40 mA.
The TPS3710-Q1 asserts the output signal, as shown in Table 1. To monitor any voltage above 0.4 V, set the
input using an external resistor divider network. Broad voltage thresholds are supported that enable the device
for use in a wide array of applications.
Table 1. TPS3710-Q1 Truth Table
CONDITION
SENSE > VIT+
SENSE < VIT–
OUTPUT
OUT high
OUT low
STATUS
Output not asserted
Output asserted
7.2 Functional Block Diagram
VDD
SENSE
OUT
VIT+
GND
Copyright © 2017, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: TPS3710-Q1
TPS3710-Q1
SBVS341 –JULY 2017
www.ti.com
7.3 Feature Description
7.3.1 Input (SENSE)
The TPS3710-Q1 comparator has two inputs: one external input, and one input connected to the internal
reference. The comparator rising threshold is trimmed to be equal to the reference voltage (400 mV). The
comparator also has a built-in falling hysteresis that makes the device less sensitive to supply-rail noise and
provides stable operation.
The comparator input (SENSE) is able to swing from ground to 6.5 V, regardless of the device supply voltage.
Although not required in most cases, in order to reduce sensitivity to transients and layout parasitics for
extremely noisy applications, place a 1-nF to 10-nF bypass capacitor at the comparator input.
OUT is driven to logic low when the input SENSE voltage drops below (VIT-). When the voltage exceeds VIT+, the
output (OUT) goes to a high-impedance state; see Figure 1.
7.3.2 Output (OUT)
In a typical TPS3710-Q1 application, the output is connected to a reset or enable input of the processor (such as
a digital signal processor [DSP], central processing unit [CPU], field-programmable gate array [FPGA], or
application-specific integrated circuit [ASIC]) or the output is connected to the enable input of a voltage regulator
(such as a dc-dc converter or low-dropout regulator [LDO]).
The TPS3710-Q1device provides an open-drain output (OUT). Use a pullup resistor to hold this line high when
the output goes to high impedance (not asserted). To connect the output to another device at the correct
interface-voltage level, connect a pullup resistor to the proper voltage rail. The TPS3710-Q1 output can be pulled
up to 18 V, independent of the device supply voltage.
Table 1 and the Input (SENSE) section describe how the output is asserted or deasserted. See Figure 1 for a
timing diagram that describes the relationship between threshold voltage and the respective output.
7.3.3 Immunity to Input-Pin Voltage Transients
The TPS3710-Q1i s relatively immune to short voltage transient spikes on the sense pin. Sensitivity to transients
depends on both transient duration and amplitude; see Figure 7, Minimum Pulse Width vs Threshold Overdrive
Voltage.
7.4 Device Functional Modes
7.4.1 Normal Operation (VDD > UVLO)
When the voltage on VDD is greater than 1.8 V for at least 150 µs, the OUT signal correspond to the voltage on
SENSE as listed in Table 1.
7.4.2 Undervoltage Lockout (V(POR) < VDD < UVLO)
When the voltage on VDD is less than the device UVLO voltage, and greater than the power-on reset voltage,
V(POR), the OUT signal is asserted regardless of the voltage on SENSE.
7.4.3 Power-On Reset (VDD < V(POR)
)
When the voltage on VDD is lower than the required voltage to internally pull the asserted output to GND (V(POR)),
SENSE is in a high-impedance state.
10
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
Product Folder Links: TPS3710-Q1
TPS3710-Q1
www.ti.com
SBVS341 –JULY 2017
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The TPS3710-Q1 device is a wide-supply voltage comparator that operates over a VDD range of 1.8 V to
18 V. The device has a high-accuracy comparator with an internal 400-mV reference and an open-drain output
rated to 18 V for precision voltage detection. The device can be used as a voltage monitor. The monitored
voltage are set with the use of external resistors.
8.1.1 VPULLUP to a Voltage Other Than VDD
The output is often tied to VDD through a resistor. However, some applications may require the output to be
pulled up to a higher or lower voltage than VDD to correctly interface with the reset and enable pins of other
devices.
VMON
1.8 V to 18 V
0.01 ꢀF
VPULLUP
Up to 18 V
R1
VDD
RP
To a reset or enable
input of the system.
SENSE
OUT
R2
GND
Figure 14. Interfacing to a Voltage Other Than VDD
Copyright © 2017, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: TPS3710-Q1
TPS3710-Q1
SBVS341 –JULY 2017
www.ti.com
Application Information (continued)
8.1.2 Monitoring VDD
Many applications monitor the same rail that is powering VDD. In these applications the resistor divider is simply
connected to the VDD rail.
1.8 V to 18 V
0.01 ꢀF
VPULLUP
Up to 18 V
R1
R2
VDD
SENSE
RP
To a reset or enable
input of the system.
OUT
GND
Figure 15. Monitoring the Same Voltage as VDD
8.1.3 Monitoring a Voltage Other Than VDD
Some applications monitor rails other than the one that is powering VDD. In these types of applications the
resistor divider used to set the desired threshold is connected to the rail that is being monitored.
VMON
1.8 V to 18 V
0.01 ꢀF
VPULLUP
Up to 18 V
R1
VDD
RP
To a reset or enable
input of the system.
SENSE
OUT
R2
GND
NOTE: The input can monitor a voltage greater than maximum VDD with the use of an external resistor divider
network.
Figure 16. Monitoring a Voltage Other Than VDD
12
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
Product Folder Links: TPS3710-Q1
TPS3710-Q1
www.ti.com
SBVS341 –JULY 2017
8.2 Typical Application
The TPS3710-Q1 device is a wide-supply voltage comparator that operates over a VDD range of 1.8 to 18 V. The
monitored voltage is set with the use of external resistors, so the device can be used either as a precision
voltage monitor.
VMON
1.8 V to 18 V
0.01 ꢀF
VPULLUP
Up to 18 V
R1
2.21 MΩ
RP
VDD
SENSE
49.9 kΩ
To a reset or enable
input of the system.
OUT
R2
83.5 kΩ
GND
Figure 17. Wide VIN Voltage Monitor
8.2.1 Design Requirements
For this design example, use the values summarized in Table 2 as the input parameters.
Table 2. Design Parameters
PARAMETER
DESIGN REQUIREMENT
DESIGN RESULT
12-V nominal rail with maximum falling
threshold of 10%
Monitored voltage
VMON(UV)= 10.99 V (8.33%)
8.2.2 Detailed Design Procedure
8.2.2.1 Resistor Divider Selection
The resistor divider values and target threshold voltage can be calculated by using Equation 1 to determine
VMON(UV)
.
R1
R2
≈
’
VMON(UV) = 1 +
× V
IT-
∆
÷
◊
«
(1)
where
•
•
R1 and R2 are the resistor values for the resistor divider on the SENSEx pins
VMON(UV) is the target voltage at which an undervoltage condition is detected
Choose RTOTAL ( = R1 + R2) so that the current through the divider is approximately 100 times higher than the
input current at the SENSE pin. The resistors can have high values to minimize current consumption as a result
of low input bias current without adding significant error to the resistive divider. For details on sizing input
resistors, refer to application report SLVA450, Optimizing Resistor Dividers at a Comparator Input, available for
download from www.ti.com.
Copyright © 2017, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: TPS3710-Q1
TPS3710-Q1
SBVS341 –JULY 2017
www.ti.com
8.2.2.2 Pullup Resistor Selection
To ensure the proper voltage level, the pullup resistor value is selected by ensuring that the pullup voltage
divided by the resistor does not exceed the sink-current capability of the device. This confirmation is calculated
by verifying that the pullup voltage minus the output-leakage current (Ilkg(OD)) multiplied by the resistor is greater
than the desired logic-high voltage. These values are specified in the Electrical Characteristics .
Use Equation 2 to calculate the value of the pullup resistor.
(VHI - VPU)
VPU
IO
³ RPU
³
Ilkg(OD)
(2)
8.2.2.3 Input Supply Capacitor
Although an input capacitor is not required for stability, for good analog design practice, connect a 0.1-μF low
equivalent series resistance (ESR) capacitor across the VDD and GND pins. A higher-value capacitor may be
necessary if large, fast rise-time load transients are anticipated, or if the device is not located close to the power
source.
8.2.2.4 Sense Capacitor
Although not required in most cases, for extremely noisy applications, place a 1-nF to 10-nF bypass capacitor
from the comparator input (SENSE) to the GND pin for good analog design practice. This capacitor placement
reduces device sensitivity to transients.
8.2.3 Application Curve
401
VDD = 1.8 V
VDD = 5 V
VDD = 12 V
VDD = 18 V
400.6
400.2
399.8
399.4
399
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (èC)
Figure 18. Rising Input Threshold Voltage (VIT+) vs Temperature
8.3 Do's and Don'ts
Do connect a 0.1-µF decoupling capacitor from VDD to GND for best system performance.
If the monitored rail is noisy, do connect a decoupling capacitor from the comparator input (sense) to GND.
Don't use resistors for the voltage divider that cause the current through them to be less than 100 times the input
current of the comparator without also accounting for the effect to the accuracy.
Don't use a pullup resistor that is too small, because the larger current sunk by the output then exceeds the
desired low-level output voltage (VOL).
14
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
Product Folder Links: TPS3710-Q1
TPS3710-Q1
www.ti.com
SBVS341 –JULY 2017
9 Power-Supply Recommendations
This device operates from an input voltage supply range between 1.8 V and 18 V.
10 Layout
10.1 Layout Guidelines
Placing a 0.1-µF capacitor close to the VDD pin to reduce the input impedance to the device is good analog
design practice.
10.2 Layout Example
Pullup
Voltage
RP1
Output
Flag
6
5
1
CVDD
Input
Supply
2
3
4
R1
R2
Monitored
Voltage
Figure 19. Layout Example
Copyright © 2017, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: TPS3710-Q1
TPS3710-Q1
SBVS341 –JULY 2017
www.ti.com
11 Device and Documentation Support
11.1 Device Support
11.1.1 Device Nomenclature
Table 3. Device Nomenclature
PRODUCT
DESCRIPTION
yyy is package designator
z is package quantity
TPS3710yyyz
11.2 Documentation Support
11.2.1 Related Documentation
For related documentation, see the following:
Optimizing Resistor Dividers at a Comparator Input
11.3 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.4 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.5 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
11.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
16
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
Product Folder Links: TPS3710-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TPS3710QDSERQ1
ACTIVE
WSON
DSE
6
3000 RoHS & Green
NIPDAUAG
Level-2-260C-1 YEAR
-40 to 125
5P
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS3710-Q1 :
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
Catalog: TPS3710
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
7-Jan-2021
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS3710QDSERQ1
WSON
DSE
6
3000
179.0
8.4
1.8
1.8
1.0
4.0
8.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
7-Jan-2021
*All dimensions are nominal
Device
Package Type Package Drawing Pins
WSON DSE
SPQ
Length (mm) Width (mm) Height (mm)
213.0 191.0 35.0
TPS3710QDSERQ1
6
3000
Pack Materials-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party
intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages,
costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (https:www.ti.com/legal/termsofsale.html) or other applicable terms available either
on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s
applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021, Texas Instruments Incorporated
相关型号:
TPS3710DDCR
宽输入电压电压检测器 | DDC | 6 | -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS3710DDCT
宽输入电压电压检测器 | DDC | 6 | -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS3710DSER
宽输入电压电压检测器 | DSE | 6 | -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS3710DSET
宽输入电压电压检测器 | DSE | 6 | -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS3710QDSERQ1
汽车类宽输入电压 (18V) 电压检测器 | DSE | 6 | -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS3711
36V 电压检测器Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS3711DDCR
36V 电压检测器 | DDC | 6 | -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS3711DDCT
36V 电压检测器 | DDC | 6 | -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS3760
具有感应功能、超低静态电流和延迟的 65V 过压或欠压监控器Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS3760-Q1
具有感应功能、超低 IQ 和延迟的汽车类 65V 过压或欠压监控器Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS3760A012DYYR
具有感应功能、超低静态电流和延迟的 65V 过压或欠压监控器 | DYY | 14 | -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS3760A012DYYRQ1
具有感应功能、超低 IQ 和延迟的汽车类 65V 过压或欠压监控器 | DYY | 14 | -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
©2020 ICPDF网 联系我们和版权申明