TPS65145RGERG4 [TI]
TRIPLE OUTPUT LCD SUPPLY WITH LINEAR REGULATOR AND POWER GOOD;型号: | TPS65145RGERG4 |
厂家: | TEXAS INSTRUMENTS |
描述: | TRIPLE OUTPUT LCD SUPPLY WITH LINEAR REGULATOR AND POWER GOOD CD 输出元件 |
文件: | 总32页 (文件大小:1142K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPS65140, TPS65141
TPS65145
www.ti.com
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
TRIPLE OUTPUT LCD SUPPLY WITH LINEAR REGULATOR AND POWER GOOD
Check for Samples: TPS65140, TPS65141, TPS65145
1
FEATURES
DESCRIPTION
2
•
2.7-V to 5.8-V Input Voltage Range
1.6-MHz Fixed Switching Frequency
3 Independent Adjustable Outputs
The TPS6514x series offers a compact and small
power supply solution to provide all three voltages
required by thin film transistor (TFT) LCD displays.
The auxiliary linear regulator controller can be used
to generate a 3.3-V logic power rail for systems
powered by a 5-V supply rail only.
•
•
•
Main Output up to 15 V With <1% Typical
Output Voltage Accuracy
•
•
•
•
•
•
•
•
•
•
•
Virtual Synchronous Converter Technology
Negative Regulated Charge Pump Driver VO2
Positive Charge Pump Converter VO3
Auxiliary 3.3-V Linear Regulator Controller
Internal Soft Start
The main output VO1 is a 1.6-MHz fixed frequency
PWM boost converter providing the source drive
voltage for the LCD display. The device is available in
two versions with different internal switch current
limits to allow the use of a smaller external inductor
when lower output power is required. The
TPS65140/41 has a typical switch current limit of 2.3
A and the TPS65145 has a typical switch current limit
of 1.37 A. A fully integrated adjustable charge pump
doubler/tripler provides the positive LCD gate drive
voltage. An externally adjustable negative charge
pump provides the negative gate drive voltage. Due
to the high 1.6-MHz switching frequency of the
charge pumps, inexpensive and small 220-nF
capacitors can be used.
Internal Power-On Sequencing
Fault Detection of all Outputs (TPS65140/45)
No Fault Detection (TPS65141)
Thermal Shutdown
System Power Good
Available in TSSOP-24 and QFN-24
PowerPAD™ Packages
APPLICATIONS
Additionally, the TPS6514x series has a system
power good output to indicate when all supply rails
are acceptable. For LCD panels powered by 5 V the
device has a linear regulator controller using an
external transistor to provide a regulated 3.3 V output
for the digital circuits. For maximum safety, the
TPS65140/45 goes into shutdown as soon as one of
the outputs is out of regulation. The device can be
enabled again by toggling the input or the enable
(EN) pin to GND. The TPS65141 does not enter
shutdown when one of its outputs is below its power
good threshold.
•
•
•
•
•
•
TFT LCD Displays for Notebooks
TFT LCD Displays for Monitors
Portable DVD Players
Tablet PCs
Car Navigation Systems
Industrial Displays
TPS6514x
V 1
O
Vin
2.7 V to 5.8 V
Boost
Converter
Up to 15 V / 400 mA
V 3
O
Positive Charge
Pump
Up to 30 V / 20 mA
V 2
O
Negative
Charge Pump
Up to 12 V / 20 mA
Power Good
PG
Linear Regulator
Controller
V 4
O
3.3 V
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
PowerPAD is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2003–2012, Texas Instruments Incorporated
TPS65140, TPS65141
TPS65145
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
TYPICAL APPLICATION CIRCUIT
V 1
O
V
L1
4.2 µH
I
Up to 15 V/350 mA
D1
2.7 V to 5.8 V
C3
22 µF
TPS65140
C5
C4
22 µF
R1
R2
VIN
SW
SW
C13
10 nF
COMP
GND
FB1
SUP
C2+
EN
0.22 µF
C1
ENR
C1
0.22 µF
0.22 µF
C2−/MODE
OUT3
C1+
C1−
V 2
O
V 3
O
D2
Up to 12 V/20 mA
Up to 30 V/20 mA
C12
DRV
FB2
FB3
PG
C6
0.22 µF
REF
FB4
PGND
PGND
GND
D3
R3
R4
C7
R5
0.22 µF
BASE
R6
Q1
BCP68
C11
100 nF
V 4
O
3.3 V
V
I
V
I
R7
33 kΩ
C9
4.7 µF
C9
1 µF
System Power
Good
ORDERING INFORMATION
PACKAGE(1) (2)
LINEAR REGULATOR
OUTPUT VOLTAGE
MINIMUM SWITCH
CURRENT LIMIT
TA
PACKAGE
MARKING
TSSOP
QFN
3.3 V
3.3 V
3.3 V
1.6 A
1.6 A
TPS65140PWP
TPS65141PWP
TPS65145PWP
TPS65140RGE
TPS65141RGE
TPS65145RGE
TPS65140
TPS65141
TPS65145
-40°C to 85°C
0.96 A
(1) The PWP and RGE packages are available taped and reeled. Add an R suffix to the device type (TPS65100PWPR) to order the device
taped and reeled. The PWPR package has quantities of 2000 devices per reel, and the the RGER package has 3000 devices per reel.
Without the suffix, the PWP package only, is shipped in tubes with 60 devices per tube.
(2) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
Web site at www.ti.com.
2
Submit Documentation Feedback
Copyright © 2003–2012, Texas Instruments Incorporated
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
www.ti.com
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)(1)
UNIT
-0.3 V to 6 V
Voltages on pin VIN(2)
(2)
Voltages on pin VO1, SUP, PG
-0.3 V to 15.5 V
-0.3 V to VI + 0.3 V
20 V
Voltages on pin EN, MODE, ENR(2)
Voltage on pin SW(2)
Power good maximum sink current (PG)
Continuous power dissipation
1 mA
See Dissipation Rating Table
-40°C to 150°C
-65°C to 150°C
260°C
Operating junction temperature range
Storage temperature range
Lead temperature (soldering, 10 sec)
(1) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating
conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to network ground terminal.
DISSIPATION RATINGS
TA ≤ 25°C
POWER RATING
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
PACKAGE
RΘJA
24-Pin TSSOP
24-Pin QFN
30.13 C°/W (PWP soldered)
30 C°/W
3.3 W
3.3 W
1.83 W
1.8 W
1.32 W
1.3 W
RECOMMENDED OPERATING CONDITIONS
MIN
TYP
MAX
UNIT
V
VIN
L
Input voltage range
Inductor(1)
2.7
5.8
4.7
μH
°C
TA
TJ
Operating ambient temperature
Operating junction temperature
-40
-40
85
125
°C
(1) See the application information section for further information.
ELECTRICAL CHARACTERISTICS
Vin = 3.3 V, EN = VIN, VO1 = 10 V, TA= -40°C to 85°C, typical values are at TA = 25°C (unless otherwise noted)
PARAMETER
SUPPLY CURRENT
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Vi
Input voltage range
2.7
5.5
0.9
V
ENR = GND, VO3 = 2 x VO1,
Boost converter not switching
0.7
mA
IQ
Quiescent current into VIN
VO1 = SUP = 10 V, VO3 = 2 x VO1
VO1 = SUP = 10 V, VO3 = 3 x VO1
1.7
3.9
2.7
6
Charge pump quiescent
current into SUP
IQCharge
IQEN
mA
LDO controller quiescent
current into Vin
ENR = VIN, EN = GND
300
800
μA
ISD
Shutdown current into VIN EN = ENR = GND
1
10
μA
VUVLO
Undervoltage lockout
threshold
VI falling
2.2
2.4
V
Thermal shutdown
Temperature rising
160
°C
LOGIC SIGNALS EN, ENR
VIH
VIL
II
High level input voltage
1.5
V
V
Low level input voltage
Input leakage current
0.4
0.1
EN = GND or VIN
0.01
μA
MAIN BOOST CONVERTER
Copyright © 2003–2012, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
Vin = 3.3 V, EN = VIN, VO1 = 10 V, TA= -40°C to 85°C, typical values are at TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VO1
Output voltage range
5
15
V
Minimum input to output
voltage difference
VO1-Vin
VREF
VFB
1
1.205
1.136
V
V
V
Reference voltage
1.13
1.219
1.154
Feedback regulation
voltage
1.146
Feedback input bias
current
IFB
10
100
nA
VO1 = 10 V, Isw = 500 mA
195
285
2.3
1.37
9
290
420
2.6
1.56
15
N-MOSFET on-resistance
(Q1)
rDS(on)
mΩ
VO1 = 5 V, Isw = 500 mA
TPS65140, TPS65141
TPS65145
1.6
A
A
N-MOSFET switch current
limit (Q1)
ILIM
0.96
VO1 = 10 V, Isw = 100 mA
VO1 = 5 V, Isw = 100 mA
P-MOSFET on-resistance
(Q2)
rDS(on)
Ω
14
22
Maximum P-MOSFET peak
switch current
IMAX
Ileak
1
A
Switch leakage current
Vsw = 15 V
1
1.6
10
2.1
2.1
μA
0°C ≤ TA ≤ 85°C
1.295
1.191
fSW
Oscillator frequency
MHz
-40°C ≤ TA ≤ 85°C
2.7 V ≤ VI ≤ 5.7 V; Iload = 100 mA
0 mA ≤ IO ≤ 300 mA
1.6
Line regulation
Load regulation
0.012
0.2
%/V
%/A
NEGATIVE CHARGE PUMP VO2
VO2
Vref
Output voltage range
Reference voltage
-2
V
V
1.205
1.213
0
1.219
36
Feedback regulation
voltage
VFB
IFB
-36
mV
nA
Feedback input bias
current
10
4.3
2.9
100
8
Q8 P-Channel switch
rDS(on)
rDS(on)
IO = 20 mA
Ω
Q9 N-Channel switch
rDS(on)
4.4
IO
Maximum output current
20
mA
%/V
7 V ≤ VO1 ≤ 15 V, Iload =10 mA,
VO2 = -5 V
Line regulation
0.09
Load regulation
1 mA ≤ IO ≤ 20 mA, VO2 = -5 V
0.126
%/mA
POSITIVE CHARGE PUMP VO3
VO3
Vref
Output voltage range
Reference voltage
30
V
V
1.205
1.187
1.213
1.214
1.219
Feedback regulation
voltage
VFB
IFB
1.238
100
15.5
1.8
V
Feedback input bias
current
10
9.9
1.1
4.6
1.2
nA
Q3 P-Channel switch
rDS(on)
Q4 N-Channel switch
rDS(on)
rDS(on)
IO = 20 mA
Ω
Q5 P-Channel switch
rDS(on)
8.5
Q6 N-Channel switch
rDS(on)
2.2
4
Submit Documentation Feedback
Copyright © 2003–2012, Texas Instruments Incorporated
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
www.ti.com
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
ELECTRICAL CHARACTERISTICS (continued)
Vin = 3.3 V, EN = VIN, VO1 = 10 V, TA= -40°C to 85°C, typical values are at TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
mV
D1 – D4 Shottky diode
forward voltage
Vd
IO
ID1-D4 = 40 mA
610
720
Maximum output current
20
mA
10 V ≤ VO1 ≤ 15 V, Iload = 10 mA,
VO3 = 27 V
Line regulation
0.56
0.05
%/V
%/mA
Load regulation
1 mA ≤ IO ≤ 20 mA, VO3 = 27 V
LINEAR REGULATOR CONTROLLER VO4
VO4
Output voltage
4.5 V ≤ VI ≤ 5.5 V; 10 mA ≤ IO ≤ 500 mA
Vin-VO4-VBE ≥ 0.5 V(1)
3.2
13.5
20
3.3
19
3.4
25
V
Maximum base drive
current
IBASE
mA
(1)
Vin-VO4-VBE ≥ 0.75 V
27
Line regulation
Load regulation
Start up current
4.75 V ≤ VI ≤ 5.5 V, Iload = 500 mA
1 mA ≤ IO ≤ 500 mA, VI = 5 V
VO4 ≤ 0.8 V
0.186
0.064
20
%/V
%/A
mA
11
SYSTEM POWER GOOD (PG)
V(PG, Vo1)
-12
-13
-11
-8.75% VO1
-9.5% VO2
-8% VO3
-6
-5
V
V
V(PG, Vo2)
V(PG, Vo3)
VOL
Power good threshold(2)
-5
V
PG output low voltage
I(sink) = 500 μA
0.3
1
V
IL
PG output leakage current VPG = 5 V
0.001
µA
(1) With VI = supply voltage of the TPS6514x, VO4 = output voltage of the regulator, VBE = basis emitter voltage of external transistor.
(2) The power good goes high when all 3 outputs (VO1, VO2, VO3) are above their threshold. The power good goes low as soon as one of
the outputs is below their threshold.
DEVICE INFORMATION
PWP PACKAGE
RGE PACKAGE
TOP VIEW
TOP VIEW
1
2
3
4
24
23
22
21
FB1
FB4
EN
ENR
BASE
VIN
COMP
FB2
23 22 21 20
24
19
18
COMP
ENR
EN
1
2
3
4
5
6
C2−/MODE
C2+
SW
5
6
20
19
REF
17
16
15
14
13
SW
GND
DRV
Exposed
Thermal Die*
OUT3
FB3
7
18
17
16
15
14
13
PGND
PGND
SUP
PG
FB1
FB4
8
C1−
GND
9
C1+
PG
BASE
7
8
9
11 12
10
10
11
12
C2−/MODE
C2+
GND
FB3
OUT3
Copyright © 2003–2012, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
www.ti.com
Terminal Functions
TERMINAL
I/O
DESCRIPTION
NO.
(PWP)
NAME
VIN
NO. (RGE)
4
7
3
I
I
Input voltage pin of the device.
Enable pin of the device. This pin should be terminated and not be left floating. A logic
high enables the device and a logic low shuts down the device.
EN
24
Compensation pin for the main boost converter. A small capacitor is connected to this
pin.
COMP
22
10
1
Open drain output indicating when all outputs VO1, VO2, VO3 are within 10% of their
nominal output voltage. The output goes low when one of the outputs falls below 10%
of their nominal output voltage.
PG
13
O
I
Enable pin of the linear regulator controller. This pin should be terminated and not be
left floating. Logic high enables the regulator and a logic low puts the regulator in
shutdown.
ENR
23
2
C1+
C1-
16
17
18
21
20
19
20
21
24
23
Positive terminal of the charge pump flying capacitor
Negative terminal of the charge pump flying capacitor
External charge pump driver
DRV
FB2
REF
O
I
Feedback pin of negative charge pump
Internal reference output typically 1.23 V
O
Feedback pin of the linear regulator controller. The linear regulator controller is set to a
fixed output voltage of 3.3 V or 3 V depending on the version.
FB4
2
5
I
BASE
GND
3
11, 19
7, 8
12
6
O
Base drive output for the external transistor
Ground
14, 22
10, 11
15
PGND
FB3
Power ground
I
Feedback pin of positive charge pump
Positive charge pump output
OUT3
13
16
O
Negative terminal of the charge pump flying capacitor and charge pump MODE pin. If
the flying capacitor is connected to this pin, the converter operates in a voltage tripler
mode. If the charge pump needs to operate in a voltage doubler mode, the flying
capacitor is removed and the C2-/MODE pin needs to be connected to GND.
C2-/MODE
C2+
15
14
9
18
17
12
Positive terminal for the charge pump flying capacitor. If the device runs in voltage
doubler mode, this pin needs to be left open.
Supply pin of the positive, negative charge pump, boost converter, and gate drive
circuit. This pin needs to be connected to the output of the main boost converter and
cannot be connected to any other voltage source. For performance reasons, it is not
recommended for a bypass capacitor to be connected directly to this pin.
SUP
I
FB1
SW
1
4
I
I
Feedback pin of the boost converter
Switch pin of the boost converter
5, 6
8, 9
PowerPAD
™ /Thermal
Die
The PowerPAD or exposed thermal die needs to be connected to power ground pins
(PGND)
6
Submit Documentation Feedback
Copyright © 2003–2012, Texas Instruments Incorporated
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
www.ti.com
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
FUNCTIONAL BLOCK DIAGRAM
VIN
SW
SW
Q2
Main boost
converter
D
S
EN
Bias V = 1.213 V
ref
Current Limit
and
Soft Start
Thermal Shutdown
Start−Up Sequencing
Undervoltage Detection
Overvoltage Detection
Short Circuit Protection
FB1
FB2
FB3
1.6-MHz
Oscillator
SUP
Control Logic
Gate Drive Circuit
D
S
Q1
COMP
FB1
Comparator
Sawtooth
Generator
SUP
VFB
1.146 V
FB3
SUP
(V
)
O
Positive
SUP
GM Amplifier
Low Gain
Charge Pump
D
S
Q3
Current
Control
VFB
1.146 V
Vref
1.214 V
C1−
Gain Select
(Doubler or
Tripler Mode)
D
S
Q4
SUP
Negative
Charge Pump
SUP
Soft Start
C1+
D
S
Current
Control
Soft Start
Q8
Q9
D
DRV
Q7
S
D
S
SUP
D
Vo3
C2+
D1
D4
D2
Q5
S
FB2
D3
D
Vref
0 V
Q6
S
C2−
PG
Reference
Output
Vref
1.213 V
Vref
1.213 V
Vin
Soft Start
Iref = 20 mA
REF
FB4
Short Circuit
Detect
System Power
Good
FB1
~1 V
Vref
D
Logic and
1-µs Glitch
Filter
FB2
FB3
S
D
S
Q10
Linear
Regulator
Controller
1.213 V
ENR
BASE
GND
GND
PGND
PGND
Copyright © 2003–2012, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
www.ti.com
FIGURE
Table of Graphs
Main Boost Converter
Efficiency, main boost converter VO1
vs Load current
1
2
η
Efficiency, main boost converter VO1
Efficiency
vs Load current
vs Input voltage
3
fsw
Switching frequency
vs Free-air temperature
vs Free-air temperature
4
rDS(on)
rDS(on) N-Channel main switch Q1
PWM operation continuous mode
PWM operation, discontinuous (light load)
Load transient response, CO = 22 μF
Load transient response, CO = 2 x 22 μF
Power-up sequencing
5
6
7
8
9
10
11
Soft start VO1
Negative Charge Pump
Imax
VO2 maximum load current
vs Output voltage VO1
12
Positive Charge Pump
Imax
Imax
VO3 maximum load current
vs Output voltage VO1 (doubler mode)
vs Output voltage VO1 (tripler mode)
13
14
VO3 Maximum load current
8
Submit Documentation Feedback
Copyright © 2003–2012, Texas Instruments Incorporated
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
www.ti.com
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
TYPICAL CHARACTERISTICS
EFFICIENCY
vs
EFFICIENCY
vs
EFFICIENCY
vs
LOAD CURRENT
LOAD CURRENT
INPUT VOLTAGE
100
90
100
100
95
ILoad at Vo1 = 100 mA
Vo2, Vo3 = No Load, Switching
90
80
Vo1 = 6 V
80
70
60
50
40
Vo1 = 6 V
Vo1 = 10 V
90
70
60
50
Vo1 = 10 V
Vo1 = 10 V
85
Vo1 = 15 V
Vo1 = 15 V
Vo1 = 15 V
40
80
30
20
30
20
10
75
70
V = 3.3 V
Vo2, Vo3 = No Load, Switching
V = 5 V
Vo2, Vo3 = No Load, Switching
I
I
10
1
10 100
1 k
1
10 100
1 k
2.5
3
3.5
4
4.5
5
5.5
6
I
− Load Current − mA
I
− Load Current − mA
V
I
- Input Voltage - V
L
L
Figure 1.
Figure 2.
Figure 3.
SWITCHING FREQUENCY
vs
FREE-AIR TEMPERATURE
rDS(on) N-CHANNEL MAIN SWITCH
vs
PWM OPERATION CONTINUOUS
MODE
FREE-AIR TEMPERATURE
1.9
1.8
1.7
1.6
1.5
350
V
300
250
SW
10 V/div
V = 2.7 V
I
Vo1 = 5 V
V = 3.3 V
I
V
O
50 mV/div
V = 5.8 V
I
200
150
100
Vo1 = 10 V
1.4
1.3
I
V = 3.3 V
I
V = 10 V/300 mA
O
L
Vo1 = 15 V
1 A/div
−40 −20
0
20
40
60
80 100
−40 −20
0
20
40
60
80
100
250 ns/div
T − Free-Air Temperature − °C
A
T
A
− Free-Air Temperature − °C
Figure 4.
Figure 5.
Figure 6.
LOAD TRANSIENT RESPONSE
PWM OPERATION AT LIGHT LOAD
LOAD TRANSIENT RESPONSE
V
= 3.3 V
I
Vo1 = 10 V, C = 2*22 µF
O
Vo1
200 mV/div
Vo1
100 mV/div
V
SW
10 V/div
V
O
50 mV/div
V = 3.3 V
I
V
= 10 V/10 mA
O
I
I
O
O
V
= 3.3 V
I
I
50 mA to 250 mA
L
50 mA to 250 mA
Vo1 = 10 V, C = 22 µF
O
500 mA/div
100 µs/div
100 µs/div
250 ns/div
Figure 7.
Figure 8.
Figure 9.
Copyright © 2003–2012, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
POWER-UP SEQUENCING
SOFT START VO1
VO2 MAXIMUM LOAD CURRENT
0.20
V = 3.3 V
Vo2 = −8 V
I
0.18
0.16
0.14
0.12
0.10
0.08
V
= 10 V,
= 300 mA
O
T
A
= −40°C
I
O
Vo1
5 V/div
T
A
= 85°C
Vo1
5 V/div
Vo2
5 V/div
T
= 25°C
A
0.06
0.04
Vo3
10 V/div
I
I
V = 3.3 V
I
500
mA/div
V
= 10 V,
O
0.02
0
8.8
9.8
10.8 11.8 12.8 13.8 14.8
500 µs/div
500 µs/div
Vo1 − Output Voltage − V
Figure 10.
Figure 11.
Figure 12.
VO3 MAXIMUM LOAD CURRENT
VO3 MAXIMUM LOAD CURRENT
0.14
0.12
0.10
0.08
0.06
0.04
0.12
0.10
0.08
0.06
0.04
0.02
0
T
A
= −40°C
Vo3 = 18 V (Doubler Mode)
T
A
= −40°C
T
A
= 85°C
T
A
= 25°C
T
A
= 25°C
T
A
= 85°C
0.02
0
Vo3 = 28 V (Tripler Mode)
11 12 13 14
9
9
10
15
10
11
12
13
14
15
Vo1 − Output Voltage − V
Vo1 − Output Voltage − V
Figure 13.
Figure 14.
DETAILED DESCRIPTION
The TPS6514x series consists of a main boost converter operating with a fixed switching frequency of 1.6 MHz
to allow for small external components. The boost converter output voltage VO1 is also the input voltage,
connected via the pin SUP, for the positive and negative charge pump. The linear regulator controller is
independent from this system with its own enable pin. This allows the linear regulator controller to continue to
operate while the other supply rails are disabled or in shutdown due to a fault condition on one of their outputs.
Refer to the functional block diagram for more information.
Main Boost Converter
The main boost converter operates with PWM and a fixed switching frequency of 1.6 MHz. The converter uses a
unique fast response, voltage mode controller scheme with input voltage feedforward. This achieves excellent
line and load regulation (0.2% A load regulation typical) and allows the use of small external components. To add
higher flexibility to the selection of external component values, the device uses external loop compensation.
Although the boost converter looks like a nonsynchronous boost converter topology operating in discontinuous
mode at light load, the TPS6514x series maintains continuous conduction even at light load currents. This is
accoplished using the Virtual Synchronous Converter Technology for improved load transient response. This
architecture uses an external Schottky diode and an integrated MOSFET in parallel connected between SW and
SUP (see the functional block diagram). The integrated MOSFET Q2 allows the inductor current to become
negative at light load conditions. For this purpose, a small integrated P-channel MOSFET with typically 10 Ω
rDS(on) is sufficient. When the inductor current is positive, the external Schottky diode with the lower forward
voltage conducts the current. This causes the converter to operate with a fixed frequency in continuous
conduction mode over the entire load current range. This avoids the ringing on the switch pin as seen with a
standard nonsynchronous boost converter and allows a simpler compensation for the boost converter.
10
Submit Documentation Feedback
Copyright © 2003–2012, Texas Instruments Incorporated
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
www.ti.com
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
Power-Good Output
The TPS6514x sereis has an open-drain power-good output with a maximum sink capability of 1 mA. The power-
good output goes high as soon as the main boost converter VO1 and the negative and the positive charge pumps
are within regulation. The power-good output goes low as soon as one of the outputs is out of regulation. In this
case, the device goes into shutdown at the same time. See the electrical characteristics table for the power-good
thresholds.
Enable and Power-On Sequencing (EN, ENR)
The device has two enable pins. These pins should be terminated and not left floating to prevent faulty operation.
Pulling the enable pin (EN) high enables the device and starts the power-on sequencing with the main boost
converter VO1 coming up first, then the negative and positive charge pump. The linear regulator has an
independent enable pin (ENR). Pulling this pin low disables the regulator, and pulling this pin high enables this
regulator.
If the enable pin (EN) is pulled high, the device starts its power-on sequencing. The main boost converter starts
up first with its soft start. If the output voltage has reached 91.25% of its output voltage, the negative charge
pump comes up next. The negative charge pump starts with a soft start and when the output voltage has
reached 91% of the nominal value, the positive charge pump comes up with the soft start. Pulling the enable pin
low shuts down the device. Dependent on load current and output capacitance, each of the outputs comes down.
Positive Charge Pump
The TPS6514x series has a fully regulated integrated positive charge pump generating VO3. The input voltage
for the charge pump is applied to the SUP pin that is equal to the output of the main boost converter VO1. The
charge pump is capable of supplying a minimum load current of 20 mA. Higher load currents are possible
depending on the voltage difference between VO1 and VO3. See Figure 13 and Figure 14.
Negative Charge Pump
The TPS6514x sereis has a regulated negative charge pump using two external Schottky diodes. The input
voltage for the charge pump is applied to the SUP pin that is connected to the output of the main boost converter
VO1. The charge pump inverts the main boost converter output voltage and is capable of supplying a minimum
load current of 20 mA. Higher load currents are possible depending on the voltage difference between VO1 and
VO2. See Figure 12.
Linear Regulator Controller
The TPS6514x series includes a linear regulator controller to generate a 3.3-V rail which is useful when the
system is powered from a 5-V supply. The regulator is independent from the other voltage rails of the device and
has its own enable (ENR). Since most of the systems require this voltage rail to come up first it is recommended
to use a R-C delay on EN. This delays the start-up of the main boost converter which reduces the inrush current
as well.
Soft Start
The main boost converter as well as the charge pumps and linear regulator have an internal soft start. This
avoids heavy voltage drops at the input voltage rail or at the output of the main boost converter VO1 during start-
up. See Figure 10 and Figure 11. During softstart of the main boost converter VO1 the internal current limit
threshold is increased in three steps. The device starts with the first step where the current limit is set to 2/5 of
the typical current limit (2/5 of 2.3A) for 1024 clock cycles then increased to 3/5 of the current limit for 1024 clock
cycles and the 3rd step is the full current limit. The TPS65141 has an extended softstart time where each step is
2048 clock cycles.
Fault Protection
All of the outputs of the TPS65140/45 have short-circuit detection and cause the device to go into shutdown. The
TPS65141, as an exception, does not enter shutdown in case one of the outputs falls below its power good
threshold. The main boost converter has overvoltage and undervoltage protection. If the output voltage VO1 rises
above the overvoltage protection threshold of typically 5% of VO1, then the device stops switching, but remains
operational. When the output voltage falls below this threshold, the converter continues operation. When the
output voltage falls below the undervoltage protection threshold of typically 8.75% of VO1, because of a short-
Copyright © 2003–2012, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
www.ti.com
circuit condition, the TPS65140/45 goes into shutdown. Because there is a direct pass from the input to the
output through the diode, the short-circuit condition remains. If this condition needs to be avoided, a fuse at the
input or an output disconnect using a single transistor and resistor is required. The negative and positive charge
pumps have an undervoltage lockout (UVLO) to protect the LCD panel of possible latch-up conditions due to a
short-circuit condition or faulty operation. When the negative output voltage is typically above 9.5% of its output
voltage (closer to ground), then the device enters shutdown. When the positive charge pump output voltage,
VO3, is below 8% typical of its output voltage, the device goes into shutdown. See the fault protection thresholds
in the electrical characteristics table. The device is enabled by toggling the enable pin (EN) below 0.4 V or by
cycling the input voltage below the UVLO of 1.7 V. The linear regulator reduces the output current to 20 mA
typical under a short-circuit condition when the output voltage is typically < 1 V. See the functional block diagram.
The linear regulator does not go into shutdown under a short-circuit condition.
Thermal Shutdown
A thermal shutdown is implemented to prevent damage due to excessive heat and power dissipation. Typically,
the thermal shutdown threshold is 160°C. If this temperature is reached, the device goes into shutdown. The
device can be enabled by toggling the enable pin to low and back to high or by cycling the input voltage to GND
and back to VI again.
12
Submit Documentation Feedback
Copyright © 2003–2012, Texas Instruments Incorporated
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
www.ti.com
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
APPLICATION INFORMATION
BOOST CONVERTER DESIGN PROCEDURE
The first step in the design procedure is to calculate the maximum possible output current of the main boost
converter under certain input and output voltage conditions. Below is an example for a 3.3-V to 10-V conversion:
Vin = 3.3 V, Vout = 10 V, Switch voltage drop Vsw = 0.5 V, Schottky diode forward voltage VD = 0.8 V
1. Duty cycle:
V
) V * V
out
10 V ) 0.8 V * 3.3 V
10 V ) 0.8 V * 0.5 V
D
in
+
D +
+ 0.73
V
) V * V
sw
out
D
2. Average inductor current:
I
out
300 mA
1 * 0.73
I +
+
+ 1.11 A
L
1 * D
3. Inductor peak-to-peak ripple current:
ƪVin
ƫ
* V
D
sw
f L
(3.3 V * 0.5 V) 0.73
Di +
+
+ 304 mA
L
1.6 MHz 4.2 mH
s
4. Peak switch current:
Di
304 mA
L
I
+ I )
+ 1.11 A )
+ 1.26 A
swpeak
L
2
2
The integrated switch, the inductor, and the external Schottky diode must be able to handle the peak switch
current. The calculated peak switch current has to be equal or lower than the minimum N-MOSFET switch
current limit as specified in the electrical characteristics table (1.6 A for the TPS65140/41 and 0.96 A for the
TPS65145). If the peak switch current is higher, then the converter cannot support the required load current. This
calculation must be done for the minimum input voltage where the peak switch current is highest. The calculation
includes conduction losses like switch rDS(on) (0.5 V) and diode forward drop voltage losses (0.8 V). Additional
switching losses, inductor core and winding losses, etc., require a slightly higher peak switch current in the actual
application. The above calculation still allows for a good design and component selection.
Inductor Selection
Several inductors work with the TPS6514x. Especially with the external compensation, the performance can be
adjusted to the specific application requirements. The main parameter for the inductor selection is the saturation
current of the inductor which should be higher than the peak switch current as calculated above with additional
margin to cover for heavy load transients and extreme start-up conditions. Another method is to choose the
inductor with a saturation current at least as high as the minimum switch current limit of 1.6 A for the
TPS65140/41 and 0.96 A for the TPS65145. The different switch current limits allow selection of a physically
smaller inductor when less output current is required. The second important parameter is the inductor DC
resistance. Usually, the lower the DC resistance, the higher the efficiency. However, the inductor DC resistance
is not the only parameter determining the efficiency. Especially for a boost converter where the inductor is the
energy storage element, the type and material of the inductor influences the efficiency as well. Especially at high
switching frequencies of 1.6 MHz, inductor core losses, proximity effects, and skin effects become more
important. Usually, an inductor with a larger form factor yields higher efficiency. The efficiency difference
between different inductors can vary between 2% to 10%. For the TPS6514x, inductor values between 3.3 μH
and 6.8 μH are a good choice but other values can be used as well. Possible inductors are shown in Table 1.
Copyright © 2003–2012, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
www.ti.com
Table 1. Inductor Selection
DEVICE
INDUCTOR VALUE
4.7 μH
COMPONENT SUPPLIER
Coilcraft DO1813P-472HC
DIMENSIONS / mm
8,89 x 6,1 x 5
ISAT/DCR
2.6 A/54 mΩ
4.2 μH
4.7 μH
3.3 μH
4.2 μH
3.3 μH
3.3 μH
3.3 μH
3.3 μH
4.7 μH
3.3 μH
Sumida CDRH5D28 4R2
Sumida CDC5D23 4R7
5,7 x 5,7 x 3
6 x 6 x 2,5
2.2 A/23 mΩ
1.6 A/48 mΩ
1.8 A/65 mΩ
1.8 A/60 mΩ
1.9 A/50 mΩ
1.5 A/26 mΩ
1.4 A/120 mΩ
1.45 A/69 mΩ
1 A/260 mΩ
1.3 A/160 mΩ
TPS65140
Wuerth Elektronik 744042003
Sumida CDRH6D12 4R2
Sumida CDRH6D12 3R3
Sumida CDPH4D19 3R3
Coilcraft DO1606T-332
4,8 x 4,8 x 2
6,5 x 6, 5 x 1,5
6,5 x 6,5 x 1,5
5,1 x 5,1 x 2
6,5 x 5,2 x 2
3,2 x 3,2 x 2
5,5 x 3,5 x 1
6,6 x 5,5 x 1
TPS65145
Sumida CDRH2D18/HP 3R3
Wuerth Elektronik 744010004
Coilcraft LPO6610-332M
Output Capacitor Selection
For best output voltage filtering, a low ESR output capacitor is recommended. Ceramic capacitors have a low
ESR value but depending on the application, tantalum capacitors can be used as well. A 22-μF ceramic output
capacitor works for most of the applications. Higher capacitor values can be used to improve load transient
regulation. See Table 2 for the selection of the output capacitor. The output voltage ripple can be calculated as:
I L
I
p
out
1
DV
+
*
) I ESR
p
ƪ
ƫ
out
C
f
V
) V * V
s
out
out
d
in
with:
IP = Peak switch current as calculated in the previous section with ISW(peak)
.
L = Selected inductor value
IOUT = Normal load current
fs = Switching frequency
Vd = Rectifier diode forward voltage (typical 0.3 V)
COUT = Selected output capacitor
ESR = Output capacitor ESR value
Input Capacitor Selection
For good input voltage filtering, low ESR ceramic capacitors are recommended. A 22-μF ceramic input capacitor
is sufficient for most of applications. For better input voltage filtering, this value can be increased. See Table 2
and the typical applications for input capacitor recommendations.
Table 2. Input and Output Capacitors Selection
CAPACITOR
22 μF/1210
22 μF/1206
VOLTAGE RATING
COMPONENT SUPPLIER
Taiyo Yuden EMK325BY226MM
Taiyo Yuden JMK316BJ226
COMMENTS
16 V
CO
CI
6.3 V
Rectifier Diode Selection
To achieve high efficiency, a Schottky diode should be used. The voltage rating should be higher than the
maximum output voltage of the converter. The average forward current should be equal to the average inductor
current of the converter. The main parameter influencing the efficiency of the converter is the forward voltage and
the reverse leakage current of the diode; both should be as low as possible. Possible diodes are: On
Semiconductor MBRM120L, Microsemi UPS120E, and Fairchild Semiconductor MBRS130L.
14
Submit Documentation Feedback
Copyright © 2003–2012, Texas Instruments Incorporated
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
www.ti.com
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
Converter Loop Design and Stability
The TPS6514x converter loop can be externally compensated and allows access to the internal
transconductance error amplifier output at the COMP pin. A small feedforward capacitor across the upper
feedback resistor divider speeds up the circuit as well. To test the converter stability and load transient
performance of the converter, a load step from 50 mA to 250 mA is applied and the output voltage of the
converter is monitored. Applying load steps to the converter output is a good tool to judge the stability of such a
boost converter.
Design Procedure Quick Steps
1. Select the feedback resistor divider to set the output voltage.
2. Select the feedforward capacitor to place a zero at 50 kHz.
3. Select the compensation capacitor on pin COMP. The smaller the value, the higher the low frequency gain.
4. Use a 50-kΩ potentiometer in series to Cc and monitor Vout during load transients. Fine tune the load
transient by adjusting the potentiometer. Select a resistor value that comes closest to the potentiometer
resistor value. This needs to be done at the highest Vin and highest load current because stability is most
critical at these conditions.
Setting the Output Voltage and Selecting the Feedforward Capacitor
The output voltage is set by the external resistor divider and is calculated as:
R1
R2
+ 1.146 V ƪ1 ) ƫ
V
out
Across the upper resistor, a bypass capacitor is required to speed up the circuit during load transients as shown
in Figure 15.
V 1
O
Up to 10 V/150 mA
D1
C8
6.8 pF
C4
22 µF
R1
430 kΩ
SW
SW
FB1
SUP
R2
56 kΩ
C2 0.22 µF
C2+
C2−/MODE
Figure 15. Feedforward Capacitor
Together with R1 the bypass capacitor C8 sets a zero in the control loop at approximately 50 kHz:
1
1
C8 +
+
2 p f R1
2 p 50 kHz R1
z
A value closest to the calculated value should be used. Larger feedforward capacitor values reduce the load
regulation of the converter and cause load steps as shown in Figure 16.
Copyright © 2003–2012, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
www.ti.com
Load Step
Figure 16. Load Step Caused By A Too Large Feedforward Capacitor Value
Compensation
The regulator loop can be compensated by adjusting the external components connected to the COMP pin. The
COMP pin is connected to the output of the internal transconductance error amplifier. A typical compensation
scheme is shown in Figure 17.
C
C
VIN
R
C
COMP
15 kΩ
1 nF
Figure 17. Compensation Network
The compensation capacitor Cc adjusts the low frequency gain, and the resistor value adjusts the high frequency
gain. The following formula calculates at what frequency the resistor increases the high frequency gain.
1
f +
z
2 p Cc Rc
Lower input voltages require a higher gain and a lower compensation capacitor value. A good start is Cc = 1 nF
for a 3.3-V input and Cc = 2.2 nF for a 5-V input. If the device operates over the entire input voltage range from
2.7 V to 5.8 V, a larger compensation capacitor up to 10 nF is recommended. Figure 18 shows the load transient
with a larger compensation capacitor, and Figure 19 shows a smaller compensation capacitor.
C
C
= 4.7 nF
Figure 18. CC = 4. 7 nF
16
Submit Documentation Feedback
Copyright © 2003–2012, Texas Instruments Incorporated
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
www.ti.com
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
C
C
= 1 nF
Figure 19. CC = 1 nF
Lastly, Rc needs to be selected. A good practice is to use a 50-kΩ potentiometer and adjust the potentiometer for
the best load transient where no oscillations should occur. These tests have to be done at the highest Vin and
highest load current because the converter stability is most critical under these conditions. Figure 20, Figure 21,
and Figure 22 show the fine tuning of the loop with Rc.
Figure 20. Overcompensated (Damped Oscillation), RC Is Too Large
Figure 21. Undercompensated (Loop Is Too Slow), RC Is Too Small
Copyright © 2003–2012, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
www.ti.com
Figure 22. Optimum, RC Is Ideal
Negative Charge Pump
The negative charge pump provides a regulated output voltage by inverting the main output voltage, VO1. The
negative charge pump output voltage is set with external feedback resistors.
The maximum load current of the negative charge pump depends on the voltage drop across the external
Schottky diodes, the internal on resistance of the charge pump MOSFETS Q8 and Q9, and the impedance of the
flying capacitor, C12. When the voltage drop across these components is larger than the voltage difference from
VO1 to VO2, the charge pump is in drop out, providing the maximum possible output current. Therefore, the
higher the voltage difference between VO1 and VO2, the higher the possible load current. See Figure 12 for the
possible output current versus boost converter voltage VO1 and the calculations below.
Voutmin = -(VO1 - 2 VD - IO (2 x rDS(on)Q8 + 2 x rDS(on)Q9 + Xcfly))
Setting the output voltage:
R3
R4
R3
V
= -V
x
REF
= -1.213 V x
OUT
R4
(1)
(2)
|V
|
|V
|
OUT
REF
OUT
R3 = R4 x
= R4 x
V
1.213
The lower feedback resistor value, R4, should be in a range between 40 kΩ to 120 kΩ or the overall feedback
resistance should be within 500 kΩ to 1 MΩ. Smaller values load the reference too heavy and larger values may
cause stability problems. The negative charge pump requires two external Schottky diodes. The peak current
rating of the Schottky diode has to be twice the load current of the output. For a 20 mA output current, the dual
Schottky diode BAT54 or similar is a good choice.
Positive Charge Pump
The positive charge pump can be operated in a voltage doubler mode or a voltage tripler mode depending on the
configuration of the C2+ and C2-/MODE pins. Leaving the C2+ pin open and connecting C2-/MODE to GND
forces the positive charge pump to operate in a voltage doubler mode. If higher output voltages are required the
positive charge pump can be operated as a voltage tripler. To operate the charge pump in the voltage tripler
mode, a flying capacitor needs to be connected to C2+ and C2-/MODE.
The maximum load current of the positive charge pump depends on the voltage drop across the internal Schottky
diodes, the internal on-resistance of the charge pump MOSFETS, and the impedance of the flying capacitor.
When the voltage drop across these components is larger than the voltage difference VO1 x 2 to VO3 (doubler
mode) or VO1 x 3 to VO3 (tripler mode), then the charge pump is in dropout, providing the maximum possible
output current. Therefore, the higher the voltage difference between VO1 x 2 (doubler) or VO1 x 3 (tripler) to VO3,
the higher the possible load current. See Figure 13 and Figure 14 for output current versus boost converter
voltage, VO1, and the following calculations.
18
Submit Documentation Feedback
Copyright © 2003–2012, Texas Instruments Incorporated
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
www.ti.com
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
Voltage doubler:
VO3max = 2 x VO1 - (2 VD + 2 x IO x (2 x rDS(on)Q5 + rDS(on)Q3 + rDS(on)Q4 + XC1))
Voltage tripler:
VO3max = 3 x VO - (3 x VD + 2 x IO x (3 x rDS(on)Q5 + rDS(on)Q3 + rDS(on)Q4 + XC1 + XC2))
The output voltage is set by the external resistor divider and is calculated as:
R5
R6
+ 1.214 ƪ1 ) ƫ
V
out
V
V
out
out
R5 + R6
* 1 + R6
ƪ
* 1
ƫ
ƪ ƫ
1.214
V
FB
Linear Regulator Controller
The TPS6514x includes a linear regulator controller to generate a 3.3-V rail when the system is powered from a
5-V supply. Because an external npn transistor is required, the input voltage of the TPS6514x applied to VIN
needs to be higher than the output voltage of the regulator. To provide a minimum base drive current of 13.5 mA,
a minimum internal voltage drop of 500 mV from Vin to Vbase is required. This can be translated into a minimum
input voltage on VIN for a certain output voltage as the following calculation shows:
VI(min) = VO4 + VBE + 0.5 V
The base drive current together with the hFE of the external transistor determines the possible output current.
Using a standard npn transistor like the BCP68 allows an output current of 1 A and using the BCP54 allows a
load current of 337 mA for an input voltage of 5 V. Other transistors can be used as well, depending on the
required output current, power dissipation, and PCB space. The device is stable with a 4.7-μF ceramic output
capacitor. Larger output capacitor values can be used to improve the load transient response when higher load
currents are required.
Thermal Information
An influential component of the thermal performance of a package is board design. To take full advantage of the
heat dissipation abilities of the PowerPAD or QFN package with exposed thermal die, a board that acts similar to
a heatsink and allows for the use of an exposed (and solderable) deep downset pad should be used. For further
information. see Texas Instrumens application notes (SLMA002) PowerPAD Thermally Enhanced Package, and
(SLMA004) Power Pad Made Easy. For the QFN package, see the application report (SLUA271) QFN/SON PCB
Attachement. Especially for the QFN package it is required to solder down the Thermal Pad to achieve the
required thermal resistance.
Layout Considerations
For all switching power supplies, the layout is an important step in the design, especially at high-peak currents
and switching frequencies. If the layout is not carefully designed, the regulator might show stability and EMI
problems. Therefore, the traces carrying high-switching currents should be routed first using wide and short
traces. The input filter capacitor should be placed as close as possible to the input pin VIN of the IC. See the
evaluation module (EVM) for a layout example.
Copyright © 2003–2012, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: TPS65140 TPS65141 TPS65145
TPS65140, TPS65141
TPS65145
SLVS497E –SEPTEMBER 2003–REVISED NOVEMBER 2012
www.ti.com
TYPICAL APPLICATIONS
Vo1
10V / 150 mA
L1
3.3uH
Vin
3.3V
D1
C3
22uF
TPS65140
R1
430
C5
6.8pF
C4
22uF
C13
1n
R7
15k
VIN
SW
SW
COMP
FB1
GND
EN
R2
56k
SUP
C1
0.22u
C2
0.22u
ENR
C2+
C2−/MODE
C1+
C1−
D2
Vo3
up to 23V/20mA
OUT3
C12 0.22u
Vo2
DRV
FB2
FB3
PG
−5 V / 20 mA
D3
REF
FB4
PGND
PGND
GND
R5
1M
C6
0.22u
R3
620k
C7
0.22u
BASE
R4
150k
R6
56k
C11
220nF
Vin
R7
33k
System Power
Good
Figure 23. Typical Application, Notebook Supply
Vo1
L1
4.7uH
Vin
5.0 V
D1
13.5V / 400 mA
C3
22uF
R7
4.3k
TPS65140
R1
820
C5
3.3pF
C4
22uF
C13
2.2n
VIN
SW
SW
COMP
GND
EN
FB1
R2
75k
SUP
C1
0.22u
ENR
C2+
C2−/MODE
OUT3
C1+
C1−
DRV
D2
Vo3
C12 0.22u
up to 23V/20mA
Vo2
−7 V / 20 mA
FB3
PG
FB2
D3
REF
FB4
PGND
PGND
GND
R5
1M
C6
0.22u
R3
750k
C7
0.22u
BASE
R4
130k
R6
56k
Vo4
3.3V/500mA
Q1
BCP68
C11
220nF
Vin
Vin
R7
33k
System Power
Good
C9
1uF
C10
4.7uF
Figure 24. Typical Application, Monitor Supply
20
Submit Documentation Feedback
Copyright © 2003–2012, Texas Instruments Incorporated
Product Folder Links: TPS65140 TPS65141 TPS65145
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
TPS65140PWP
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
ACTIVE
HTSSOP
HTSSOP
HTSSOP
HTSSOP
VQFN
PWP
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
60
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
TPS65140
TPS65140PWPG4
TPS65140PWPR
TPS65140PWPRG4
TPS65140RGER
TPS65140RGERG4
TPS65141PWP
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
PWP
PWP
PWP
RGE
RGE
PWP
PWP
PWP
PWP
RGE
RGE
PWP
PWP
PWP
PWP
RGE
60
Green (RoHS
& no Sb/Br)
TPS65140
TPS65140
TPS65140
2000
2000
3000
3000
60
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS
65140
VQFN
Green (RoHS
& no Sb/Br)
TPS
65140
HTSSOP
HTSSOP
HTSSOP
HTSSOP
VQFN
Green (RoHS
& no Sb/Br)
TPS65141
TPS65141
TPS65141
TPS65141
TPS65141PWPG4
TPS65141PWPR
TPS65141PWPRG4
TPS65141RGER
TPS65141RGERG4
TPS65145PWP
60
Green (RoHS
& no Sb/Br)
2000
2000
3000
3000
60
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS
65141
VQFN
Green (RoHS
& no Sb/Br)
TPS
65141
HTSSOP
HTSSOP
HTSSOP
HTSSOP
VQFN
Green (RoHS
& no Sb/Br)
TPS65145
TPS65145
TPS65145
TPS65145
TPS65145PWPG4
TPS65145PWPR
TPS65145PWPRG4
TPS65145RGER
60
Green (RoHS
& no Sb/Br)
2000
2000
3000
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
TPS
65145
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Orderable Device
TPS65145RGERG4
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
ACTIVE
VQFN
RGE
24
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
TPS
65145
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS65140, TPS65145 :
Automotive: TPS65140-Q1, TPS65145-Q1
•
NOTE: Qualified Version Definitions:
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS65140PWPR
TPS65140RGER
TPS65141PWPR
TPS65141RGER
TPS65145PWPR
TPS65145RGER
HTSSOP PWP
VQFN RGE
HTSSOP PWP
VQFN RGE
HTSSOP PWP
VQFN RGE
24
24
24
24
24
24
2000
3000
2000
3000
2000
3000
330.0
330.0
330.0
330.0
330.0
330.0
16.4
12.4
16.4
12.4
16.4
12.4
6.95
4.25
6.95
4.25
6.95
4.25
8.3
4.25
8.3
1.6
1.15
1.6
8.0
8.0
8.0
8.0
8.0
8.0
16.0
12.0
16.0
12.0
16.0
12.0
Q1
Q2
Q1
Q2
Q1
Q2
4.25
8.3
1.15
1.6
4.25
1.15
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS65140PWPR
TPS65140RGER
TPS65141PWPR
TPS65141RGER
TPS65145PWPR
TPS65145RGER
HTSSOP
VQFN
PWP
RGE
PWP
RGE
PWP
RGE
24
24
24
24
24
24
2000
3000
2000
3000
2000
3000
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
38.0
35.0
38.0
35.0
38.0
35.0
HTSSOP
VQFN
HTSSOP
VQFN
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
TPS65148
Compact TFT LCD Bias IC for Monitor with VCOM Buffer, Voltage Regulator for Gamma Buffer and Reset Function
TI
TPS65148RHB
Compact TFT LCD Bias IC for Monitor with VCOM Buffer, Voltage Regulator for Gamma Buffer and Reset Function
TI
TPS65148RHBR
Compact TFT LCD Bias IC for Monitor with VCOM Buffer, Voltage Regulator for Gamma Buffer and Reset Function
TI
TPS65148RHBT
Compact TFT LCD Bias IC for Monitor with VCOM Buffer, Voltage Regulator for Gamma Buffer and Reset Function
TI
©2020 ICPDF网 联系我们和版权申明