DSL240PS24-I [XPPOWER]
Ultra Slim Design;型号: | DSL240PS24-I |
厂家: | XP POWER LIMITED |
描述: | Ultra Slim Design |
文件: | 总2页 (文件大小:193K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
xppower.com
240 Watts
DSL240 Series
•
•
•
•
•
•
•
Ultra Slim Design
150% Peak Load for 3 seconds
Full Power from ꢀ40 °C to +60°C
High Efficiency – Up to 93%
Hazardous Locations Approval
Parallel Capability
3 Year Warranty
Specification
Input
General
Input Voltage
Input Frequency
Input Current
Inrush Current
Power Factor
• 88-264 VAC (120-375 VDC)
• 47-63 Hz
• 2.3 A at 115 VAC, 1.15 A at 230 VAC
• 24/48 A max at 115/230 VAC
• 0.97 typical at 230 VAC
Conforms to EN61000-3-2 Class A.
Efficiency
Isolation
• See table
• 3000 VAC Input to Output
1500 VAC Input to Ground
500 VAC Output to Ground
• 100 kHz typical PFC & main converter at
230 VAC and full load
• Volt free contacts rated at 60 VDC/ 0.3 A
on 24 V versions only
• Green LED to indicate output on. Red LED
to indicate low output voltage. See
mechanical details for operating range.
Switching Frequency
DC OK Signal
Earth Leakage Current • 3.5 mA maximum
Input Protection
• Internal fuse in line, T5.0 A/250 VAC
Output LED
Output
Output Voltage
• See table
• See table
• +1% at 100% load
• No minimum load required
• 1.0 s max
MTBF
• >370 kHrs to BELLCORE Issue 6 at 40 °C,
GB
Output Voltage Trim
Initial Set Accuracy
Minimum Load
Environmental
Operating Temperature • -40 °C to +70 °C (see derating curves)
Start Up Delay
Cooling
Operating Humidity
Protection
Storage Temperature • -40 °C to +85 °C
Operating Altitude
Shock
• Natural convection
• 20-95% RH, non-condensing
• IP20
Start Up Rise Time
Hold Up Time
Line Regulation
Load Regulation
Transient Response
• 150 ms max
• 25 ms minimum at full load and 115 VAC
•
•
1%
1% ( 5% in parallel mode)
• 4850 m
• 10% maximum deviation, recovering to
less than 1% within 2 ms for 50% step
load change at 0.2 A/µs
• IEC68-2-27, 4 g, 22 ms half sine, 3 times
in each of 6 axes
Ripple & Noise
• 100 mV pk-pk maximum, measured with
20 MHz bandwidth
Vibration
• IEC68-2-6, 10-500 Hz, 2 g 10 mins/sweep.
60 mins for each of 3 axes
Overvoltage Protection • 12 V output: 15-16.5 V,
24 V output: 30-33 V
• 120-150% of rated current
(see application note)
EMC & Safety
Emissions
Harmonic Currents
Voltage Flicker
ESD Immunity
Overload Protection
• EN55022, class B conducted & radiated
• EN61000-3-2, class A
• EN61000-3-3
• EN61000-4-2, 8 KV Contact,
15 KV Air Discharge, Perf Criteria A
• EN61000-4-3, 10 V/m Perf Criteria A
• EN61000-4-4, level 4 Perf Criteria A
• EN61000-4-5, Installation Class 4
Perf Criteria A
Short Circuit Protection • Trip and restart (hiccup mode)
auto recovery within 7 s
0.03%/°C
Temperature
Coefficient
Thermal Protection
•
Radiated Immunity
EFT/Burst
Surge
• 110°C max, measured on internal heatsink
auto recovery
• A maximum of 3 units can be paralleled.
Max power available is 90% of total rated
power. Minimum load of 10% required per
unit
Parallel Operation
Conducted Immunity
Magnetic Field
• EN61000-4-6, 10 V Perf Criteria A
• EN61000-4-8, level 4, Perf Criteria A
• EN55024, 30% 10 ms, 60% 100 ms,
100% 5000 ms Perf Criteria A, B, B
Maximum Capacitive
Load
• 7000 µF (start up delay increases to 1.5s
and rise time to 500 ms)
Dips & Interruptions
Safety Approvals
• UL508, UL60950-1, EN60950-1, ANSI/ISA
12.12.01 (Class I, Division 2, Groups A, B,
C and D)
DSL240
Typical Efficiency(2) Model Number(1)
Models and Ratings
Output Voltage
Output Power Output Voltage Trim(4) Output Current
Peak Load(3)
24.0 A
12 V
24 V
192 W
240 W
11.75-14.5 V
22.5-28.5 V
16.0 A
10.0 A
90%
93%
DSL240PS12-I
DSL240PS24-I
15.0 A
Notes
1. Add suffix ‘D’ for detachable connector option e.g. DSL240PS24-ID.
2. Typical efficiency at 230 VAC and full load.
3. Peak load is for a maximum of 3 s with 20% duty cycle. Average power is not
to exceed nominal output power.
4. Output current should be limited so that nominal output power is
not exceeded.
Mechanical Details
The green LED is lit if the output voltage is OK (10-11.2 VDC for 12 V units, 17.6-19.4 VDC for 24 V units at start up)
The red LED is lit if the output voltage is low (10-11.2 VDC for 12 V units, 17.6-19.4 VDC for 24 V units after start up)
0.3
(7.0)
4.59 (116.6)
6
1
6
1
Pin Connections
Conn Pin Designation
1
2
3
1
2
3
4
5
6
Ground
Neutral
Line
AC
Input
5.65
(143.5)
DC OK*
DC OK*
Positive
Positive
Negative
Negative
4.9
(124.50)
DC
Output
1
3
* 24 V models only.
1
3
2.52 (64.0)
‘-D’ version (detachable connectors)
Notes
1. All dimensions in inches (mm)
2. Weight: 1.916 lbs (860g)
3. Tolerance: 0.02 in ( 0.5 mm)
4. Screw terminal: 10-24 AWG cables size. Detachable connector version: 14-24 AWG cable size.
5. Connection screw maximum torque: Input: 9lbs-in (1.0 Nm), Output: 5.5 lbs-in (0.6 Nm).
Application Notes
Derating Curves
DC OK
100
80
60
40
20
0
DCOK
DCOK
Open = Output fail
Closed = Output good
Contact Rating: 0.3 A at 60 VDC
500 VDC isolation
20
30
40
-40
-20
0
10
50
60
70
Ambient Temp (˚C)
Peak Loading
258 W for 12 V
360 W for 24 V
Peak
3 sec
3 sec
Auto recovery within 7 sec
198 W for 12 V
240W for 24 V
Continuous
OCP
< 7 sec
OCP
< 7 sec
04-Jan-13
相关型号:
DSL70E6327HTSA1
Trans Voltage Suppressor Diode, 245W, 50V V(RWM), Unidirectional, 4 Element, Silicon, ROHS COMPLIANT PACKAGE-4
INFINEON
©2020 ICPDF网 联系我们和版权申明