ADW54011Z-0REEL7 [ADI]
Wideband 2.5 GHz, 37 dB Isolation at 1 GHz, CMOS 1.65V to 2.75V, 4:1 Mux/SP4T; 宽带2.5 GHz的37 dB的隔离在1 GHz ， CMOS 1.65V至2.75V ， 4 ： 1多路复用器/ SP4T
| 型号： | ADW54011Z-0REEL7 |
| 厂家： | 
ADI |
| 描述： | Wideband 2.5 GHz, 37 dB Isolation at 1 GHz, CMOS 1.65V to 2.75V, 4:1 Mux/SP4T |
| 文件： | 总17页 (文件大小：517K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Wideband 2.5 GHz, 37 dB Isolation at 1 GHz,
CMOS 1.65 V to 2.75 V, 4:1 Mux/SP4T
Data Sheet
ADG904/ADG904-R
FEATURES
FUNCTIONAL BLOCK DIAGRAMS
Wideband switch: –3 dB @ 2.5 GHz
ADG904: absorptive 4:1 mux/SP4T
ADG904-R: reflective 4:1 mux/SP4T
High off isolation (37 dB @ 1 GHz)
Low insertion loss (1.1 dB dc to 1 GHz)
Single 1.65 V to 2.75 V power supply
CMOS/LVTTL control logic
20-lead TSSOP and 4 mm × 4 mm LFCSP packages
Low power consumption (1 μA maximum)
Qualified for automotive applications
ADG904-R
ADG904
RF1
RF1
50
50
50
50
RF2
RF3
RF4
RF2
RF3
RF4
RFC
RFC
APPLICATIONS
Wireless communications
General-purpose RF switching
Dual-band applications
High speed filter selection
Digital transceiver front end switch
IF switching
1 OF 4 DECODER
A0 A1 EN
1 OF 4 DECODER
A0 A1 EN
Figure 1.
Figure 2.
Tuner modules
Antenna diversity switching
GENERAL DESCRIPTION
The parts have on-board CMOS control logic, which eliminates
the need for external control circuitry. The control inputs
are both CMOS and LVTTL compatible. The low power
consumption of these devices makes them ideally suited
for wireless applications and general-purpose high
frequency switching.
The ADG904 and ADG904-R are wideband analog 4:1
multiplexers that use a CMOS process to provide high isolation
and low insertion loss to 1 GHz. The ADG904 is an
absorptive/matched mux with 50 Ω terminated shunt legs; the
ADG904-R is a reflective mux. These devices are designed such
that the isolation is high over the dc to 1 GHz frequency range.
PRODUCT HIGHLIGHTS
The ADG904 and ADG904-R switch one of four inputs to a
common output, RFC, as determined by the 3-bit binary
1. −37 dB off isolation @ 1 GHz
2. 1.1 dB insertion loss @ 1 GHz
3. 20-lead TSSOP/LFCSP packages
address lines A0, A1, and
. A Logic 1 on the
pin disables
EN
EN
the device.
–10
–0.3
–0.4
–0.5
–0.6
–0.7
–0.8
–0.9
–1.0
–1.1
–1.2
–1.3
–1.4
–1.5
–1.6
–1.7
–1.8
–1.9
–2.0
–2.1
–2.2
–2.3
–2.4
–2.5
–2.6
–2.7
V
= 2.5V
DD
–20
–30
–40
–50
–60
–70
–80
S21
S12
V
= 2.5V
–2.8
–2.9
–3.0
DD
= 25°C
T
A
10k
100k
1M
10M
100M
1G
10G
10k
100k
1M
10M
100M
1G
10G
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 3. Off Isolation vs. Frequency
Document Feedback
Figure 4. Insertion Loss vs. Frequency
Rev. C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights ofthird parties that may result fromits use. Specifications subject to change without notice. No
licenseis granted byimplication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2004–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
IMPORTANT LINKS for the ADG904_904R*
Last content update 08/16/2013 12:48 pm
PARAMETRIC SELECTION TABLES
DESIGN COLLABORATION COMMUNITY
Choosing the Correct Switch or Multiplexer for Your Application
Switches and Multiplexers Product Selection Guide
Multiplexer Parametric Search
Collaborate Online with the ADI support team and other designers
about select ADI products.
Follow us on Twitter: www.twitter.com/ADI_News
Like us on Facebook: www.facebook.com/AnalogDevicesInc
DOCUMENTATION
AN-952: ADG9xx Wideband CMOS Switches: Frequently Asked
Questions
CN-0211: IF Band-Pass Filter Bank Switching Network for Wireless
Infrastructure
DESIGN SUPPORT
Submit your support request here:
Linear and Data Converters
Embedded Processing and DSP
Use Circuits from the Lab™ in Your Next Design
CMOS Switches Offer High Performance in Low Power, Wideband
Applications
RF Source Booklet
Telephone our Customer Interaction Centers toll free:
Americas:
Europe:
China:
1-800-262-5643
00800-266-822-82
4006-100-006
India:
Russia:
1800-419-0108
8-800-555-45-90
PRODUCT RECOMMENDATIONS & REFERENCE DESIGNS
CN-0211: IF Band-Pass Filter Bank Switching Network for Wireless
Infrastructure
Quality and Reliability
Lead(Pb)-Free Data
EVALUATION KITS & SYMBOLS & FOOTPRINTS
View the Evaluation Boards and Kits page for ADG904
SAMPLE & BUY
ADG904/ADG904-R
View the Evaluation Boards and Kits page for ADG904-R
Symbols and Footprints
View Price & Packaging
Request Evaluation Board
Request Samples Check Inventory & Purchase
Find Local Distributors
* This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet.
Note: Dynamic changes to the content on this page (labeled 'Important Links') does not
constitute a change to the revision number of the product data sheet.
This content may be frequently modified.
ADG904/ADG904-R
Data Sheet
TABLE OF CONTENTS
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 4
ESD Caution.................................................................................. 4
Pin Configurations and Function Descriptions ........................... 5
Terminology ...................................................................................... 6
Typical Performance Characteristics ............................................. 7
Test Circuits....................................................................................... 9
Applications..................................................................................... 11
Absorptive vs. Reflective ........................................................... 11
Antenna Diversity Switch.......................................................... 11
Filter Selection ............................................................................ 11
Tx/Rx Switching ......................................................................... 11
Evaluation Board ............................................................................ 12
Outline Dimensions....................................................................... 13
Ordering Guide .......................................................................... 14
Automotive Products................................................................. 14
REVISION HISTORY
/13—Rev. B to Rev. C
Changes to Features Section............................................................ 1
Changes to Figure 6.......................................................................... 5
Updated Outline Dimensions....................................................... 13
Changes to Ordering Guide .......................................................... 14
Added Automotive Product Section ............................................ 14
2/07—Rev. A to Rev. B
Updated Outline Dimensions....................................................... 13
Changes to Ordering Guide .......................................................... 14
8/05—Rev. 0 to Rev. A
Added LFCSP Package.......................................................Universal
Changes to Specifications ................................................................ 3
Changes to Absolute Maximum Ratings....................................... 4
Inserted New Figure 6...................................................................... 5
Changes to Table 4............................................................................ 5
Changes to Outline Dimensions................................................... 13
Changes to Ordering Guide .......................................................... 14
4/04—Revision 0: Initial Version
Rev. C | Page 2 of 16
Data Sheet
ADG904/ADG904-R
SPECIFICATIONS
VDD = 1.65 V to 2.75 V, GND = 0 V, Input Power = 0 dBm, all specifications TMIN to TMAX, unless otherwise noted.1
Table 1.
B Version
Parameter
Symbol
Conditions
Min
Typ2 Max
Unit
AC ELECTRICAL CHARACTERISTICS
Operating Frequency3
3 dB Frequency4
DC
2
2.5
7
GHz
GHz
dBm
dBm
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
Input Power4
0 V dc bias
0.5 V dc bias
DC to 100 MHz; VDD = 2.5 V 10%
500 MHz; VDD = 2.5 V 10%
1000 MHz; VDD = 2.5 V 10%
100 MHz
500 MHz
1000 MHz
100 MHz
500 MHz
1000 MHz
DC to 100 MHz
500 MHz
1000 MHz
DC to 100 MHz
500 MHz
16
Insertion Loss
S21, S12
S21, S12
S21, S12
S11, S22
S11, S22
0.4
0.6
1.1
60
45
37
58
32
35
27
26
30
22
23
22
8.5
0.8
0.9
1.5
Isolation—RFC to RF1–RF4
Crosstalk
51
35
30
50
35
30
21
18
15
18
16
18
Return Loss (On Channel)4
Return Loss (Off Channel)4
dB
dB
ns
1000 MHz
50% EN to 90% RF
On Switching Time4
Off Switching Time4
tON (
10
16
)
EN
tOFF (
50% EN to 10% RF
13
ns
)
EN
tTRANS
tRISE
Transition Time
50% Ax to 10% RF
10% to 90% RF
90% to 10% RF
1000 MHz
900 MHz/901 MHz, 4 dBm
12
3
7.5
16
31
3
15
5
9
ns
ns
ns
dBm
dBm
mV p-p
Rise Time4
Fall Time4
tFALL
P–1 dB
IP3
1 dB Compression4
Third-Order Intermodulation Intercept
Video Feedthrough5
DC ELECTRICAL CHARACTERISTICS
Input High Voltage
26.5
VINH
VINH
VINL
VINL
II
VDD = 2.25 V to 2.75 V
VDD = 1.65 V to 1.95 V
VDD = 2.25 V to 2.75 V
VDD = 1.65 V to 1.95 V
0 ≤ VIN ≤ 2.75 V
1.7
0.65 VCC
V
V
V
V
Input Low Voltage
0.7
0.35 VCC
1
Input Leakage Current
CAPACITANCE4
0.1
µA
RF Port On Capacitance
Digital Input Capacitance
POWER REQUIREMENTS
VDD
CRF ON
C
f = 1 MHz
f = 1 MHz
3
2
pF
pF
1.65
2.75
1
V
µA
Quiescent Power Supply Current
IDD
Digital inputs = 0 V or VDD
0.1
1 Temperature range B version: −40°C to +85°C.
2 Typical values are at VDD = 2.5 V and 25°C, unless otherwise stated.
3 Operating frequency is the point at which insertion loss degrades by 1.5 dB.
4 Guaranteed by design, not subject to production test.
5 Video feedthrough is the dc transience at the output of any port of the switch when the control voltage is switched from high to low or low to high in a 50 Ω test
setup, measured with 1 ns rise time pulses and 500 MHz bandwidth.
Rev. C | Page 3 of 16
ADG904/ADG904-R
Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 2.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability. Only one absolute maximum rating may be
applied at any one time.
Parameter
Rating
VDD to GND
Inputs to GND
Continuous Current
Input Power
–0.5 V to +4 V
–0.5 V to VDD + 0.3 V1
30 mA
18 dBm
Operating Temperature Range
Industrial (B Version)
Storage Temperature Range
Junction Temperature
TSSOP Package
–40°C to +85°C
–65°C to +150°C
150°C
Table 3. Truth Table
θJA Thermal Impedance
LFCSP Package
θJA Thermal Impedance
(4-Layer Board)
143°C/W
30.4°C/W
A1
A0
ON Switch1
EN
1
X
0
0
1
1
X
0
1
0
1
None
RF1
RF2
RF3
RF4
0
0
0
0
Lead Temperature, Soldering (10 sec)
IR Reflow, Peak Temperature (<20 sec)
ESD
300°C
235°C
1 kV
1 RFx off port inputs to ground = –0.5 V to VDD – 0.5 V.
1 Off switches have: 50 Ω termination to GND (ADG904); shunt to GND
(ADG904-R).
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. C | Page 4 of 16
Data Sheet
ADG904/ADG904-R
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
ADG904/ADG904-R
EN
1
2
20 A0
19 A1
V
DD
GND
RF1
15 GND
14 RF2
13 GND
12 GND
11 RF4
GND
RF1
GND
GND
RF3
1
2
3
4
5
3
4
5
6
7
8
9
18 GND
ADG904
TOP VIEW
(Not to Scale)
ADG904-R 17 RF2
GND
GND
RF3
16 GND
15 GND
14 RF4
13 GND
12 GND
11 GND
TOP VIEW
(Not to Scale)
GND
GND
NOTES
1. THE EXPOSED PAD IS TIED
TO SUBSTRATE, V
RFC 10
.
SS
Figure 5. 20-Lead TSSOP (RU-20)
Figure 6. 20-Lead 4 mm × 4mm LFCSP (CP-20-6)
Table 4. Pin Function Descriptions
Pin No.
20-Lead LFCSP
20-Lead TSSOP
Mnemonic Function
1
18
EN
Active Low Digital Input. When high, the device is disabled and all switches
are off. When low, Ax logic inputs determine On switches.
2
19
VDD
GND
Power Supply Input. These parts can be operated from 1.65 V to 2.75 V.
VDD should be decoupled to GND.
Ground Reference Point for All Circuitry on the Part.
3, 5, 6, 8, 9, 11, 12, 1, 3, 4, 6, 7, 9, 10,
13, 15, 16, 18
12, 13, 15, 20
4
7
2
5
8
11
14
16
17
21
RF1
RF3
RFC
RF4
RF2
A1
RF1 Port.
RF3 Port.
Common RF Port for Switch.
RF4 Port.
RF2 Port.
Logic Control Input.
Logic Control Input.
Exposed Pad. The exposed pad is tied to substrate, VSS.
10
14
17
19
20
N/A
A0
EPAD
Rev. C | Page 5 of 16
ADG904/ADG904-R
Data Sheet
TERMINOLOGY
Table 5.
Parameter
Description
VDD
IDD
Most Positive Power Supply Potential.
Positive Supply Current.
GND
Ax
Ground (0 V) Reference.
Logic Control Input.
VINL
VINH
IINL (IINH
CIN
Maximum Input Voltage for Logic 0.
Minimum Input Voltage for Logic 1.
Input Current of the Digital Input.
Digital Input Capacitance.
)
tON (
Delay between Applying the EN Control Input and the Output Switching On.
)
EN
tOFF (
Delay between Applying the EN Control Input and the Output Switching Off.
)
EN
tRISE
tFALL
tTRANS
Rise Time. Time for the RF signal to rise from 10% of the on level to 90% of the on level.
Fall Time. Time for the RF signal to fall from 90% of the on level to 10% of the on level.
Transition Time. Delay between applying the digital control input and the output switching on.
Off Isolation
Insertion Loss
Crosstalk
P–1 dB
The Attenuation between Input and Output Ports of the Switch when the Switch Control Voltage is in the Off Condition.
The Attenuation between Input and Output Ports of the Switch when the Switch Control Voltage is in the On Condition.
Measure of Unwanted Signal Coupled through from One Channel to Another as a Result of Parasitic Capacitance.
1 dB Compression Point. The RF input power level at which the switch insertion loss increases by 1 dB over its low level
value. P–1 dB is a measure of how much power the on switch can handle before the insertion loss increases by 1 dB.
IP3
Third-Order Intermodulation Intercept. This is a measure of the power in false tones that occur when closely spaced
tones are passed through a switch, and the nonlinearity of the switch causes these false tones to be generated.
Return Loss
The Amount of Reflected Power Relative to the Incident Power at a Port. Large return loss indicates good matching. By
measuring return loss, the voltage standing wave ratio (VSWR) can be calculated from conversion charts. VSWR indicates
the degree of matching present at a switch RF port.
Video
Feedthrough
Spurious Signals Present at the RF Ports of the Switch when the Control Voltage Is Switched from High to Low or Low to
High without an RF Signal Present.
Rev. C | Page 6 of 16
Data Sheet
ADG904/ADG904-R
TYPICAL PERFORMANCE CHARACTERISTICS
–0.3
–0.4
–0.5
–0.6
–0.7
–0.3
–0.4
–0.5
–0.6
–0.7
–0.8
–0.9
–1.0
–1.1
–1.2
–1.3
–1.4
–1.5
–1.6
–1.7
–1.8
–1.9
–2.0
–2.1
–2.2
–2.3
–2.4
–2.5
–2.6
–2.7
–2.8
–2.9
–3.0
T
T
= –40°C
A
–0.8
–0.9
–1.0
–1.1
–1.2
–1.3
–1.4
–1.5
–1.6
–1.7
–1.8
–1.9
–2.0
–2.1
–2.2
–2.3
–2.4
–2.5
–2.6
–2.7
–2.8
–2.9
–3.0
V
V
V
= 2.25V
= 2.75V
= 2.50V
DD
DD
DD
= +25°C
= +85°C
A
T
A
T
= 25°C
V
= 2.5V
A
DD
10k
100k
1M
10M
100M
1G
10G
10G
10G
10k
100k
1M
10M
100M
1G
10G
10G
10G
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 7. Insertion Loss vs. Frequency over Supplies
(RF1–RF4, S12, and S21)
Figure 10. Insertion Loss vs. Frequency over Temperature
((RF1–RF4, S12, and S21)
–0.3
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
V
= 1.65V TO 2.75V
DD
–0.4
–0.5
–0.6
–0.7
–0.8
–0.9
–1.0
–1.1
V
V
V
= 2.50V
= 2.75V
= 2.25V
DD
DD
DD
S21
S12
T
= 25°C
A
10k
100k
1M
10M
100M
1G
10k
100k
1M
10M
100M
1G
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 8. Insertion Loss vs. Frequency over Supplies
(RF1–RF4, S12, and S21). Zoomed Figure 7 Plot
Figure 11. Isolation vs. Frequency over Supplies
(RF1–RF4, S12, and S21)
–0.3
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
V
DD
= 2.5V
–0.4
–0.5
–0.6
–0.7
–0.8
–0.9
–1.0
–1.1
–1.2
–1.3
–1.4
–1.5
–1.6
–1.7
–1.8
–1.9
–2.0
–2.1
–2.2
–2.3
–2.4
–2.5
–2.6
–2.7
–2.8
–2.9
–3.0
V
= 1.65V
= 1.80V
= 1.95V
DD
DD
DD
V
V
T
=+85°C
=+25°C
A
T
A
T
= –40°C
A
T
= 25°C
A
10k
100k
1M
10M
100M
1G
10k
100k
1M
10M
100M
1G
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 9. Insertion Loss vs. Frequency over Supplies
(RF1–RF4, S12, and S21)
Figure 12. Isolation vs. Frequency over Temperature
(RF1–RF4, S12, and S21)
Rev. C | Page 7 of 16
ADG904/ADG904-R
Data Sheet
0
[
]
T
T
TRIG'D
: 2.40mV
–5
A0
–10
–15
–20
1
3
OFF SWITCH
–25
–30
–35
RFC
ON SWITCH
V
= 2.5V
DD
= 25°C
T
A
10k
100k
1M
10M
100M
1G
10G
CH1 1.00V
M 20.0ns
FREQUENCY (Hz)
CH3 1.00mV
Figure 16. Video Feedthrough
Figure 13. Return Loss vs. Frequency (RF1–RF4, S11)
–10
35
30
25
20
15
10
5
–20
–30
–40
–50
–60
–70
–80
V
= 2.5V
V
T
= 2.5V
= 25°C
DD
= 25°C
DD
T
A
A
0
100
10k
100k
1M
10M
100M
1G
10G
200
300
400
500
600
700
800
900
FREQUENCY (Hz)
FREQUENCY (MHz)
Figure 14. Crosstalk vs. Frequency
Figure 17. IP3 vs. Frequency
18
16
14
12
10
8
TEK RUN: 5.00GS/s ET ENVELOPE
[
]
T
A1
1
3
6
RF1/3
4
2
V
= 2.5V
DD
T
= 25°C
A
0
0
250
500
750
1000
1250
1500
FREQUENCY (MHz)
CH1
1.00V
Ch2 100mV
M 5.00ns
CH3 100mV
Figure 18. P-1 dB vs. Frequency
Figure 15. Switch Timing
Rev. C | Page 8 of 16
Data Sheet
ADG904/ADG904-R
TEST CIRCUITS
V
DD
10F
V
OUT
V
DD
DD
R
50
L
10F
ADG904R
V
DD
RFx
RF2
NETWORK
ANALYZER
V
50
RFC
V
OUT
RFx
RFC
50%
50%
50
R
V
L
Ax
V
V
S
S
50
Ax
90%
10%
1 0F 4
DECODER
V
OUT
GND
GND
V
V
S
A0
A1
EN
OUT
INSERTION LOSS = 20log
tON
Figure 19. Switch Timing: tON, tOFF
tOFF
Figure 22. Insertion Loss
V
DD
10F
V
V
DD
NETWORK
ANALYZER
10F
DD ADG904R
V
RF1
RF2
50
V
S
DD
RFC
50
V
OUT
RFx
RFC
50%
50%
V
OUT
V
Ax
R
L
R
50
L
V
50
S
90% 90%
Ax
10%
10%
V
OUT
1 0F 4
DECODER
GND
GND
V
V
A0
A1
EN
OUT
CROSSTALK = 20log
tRISE
tFALL
S
Figure 20. Switch Timing: tRISE, tFALL
Figure 23. Crosstalk
V
V
DD
V
DD
DD
10F
10F
50
V
S
DD ADG904R
ADG904R
V
V
OUT
NC
NC
RF1
RF2
R
50
L
RFx
RF2
RFC
RFC
OSCILLOSCOPE
NETWORK
ANALYZER
50
1 0F 4
DECODER
1 0F 4
DECODER
GND
GND
V
OUT
A0
A1
EN
OFF ISOLATION = 20log
A0
A1
EN
V
S
Figure 21. Off Isolation
Figure 24. Video Feedthrough
Rev. C | Page 9 of 16
ADG904/ADG904-R
Data Sheet
V
V
DD
DD
10F
10F
V
DD ADG904R
DD ADG904R
V
RF1
RF2
RF1
RF2
50
RF
SOURCE
50
RFC
SPECTRUM
ANALYZER
RFC
SPECTRUM
ANALYZER
RF
COMBINER
SOURCE
V
S
RF
SOURCE
1 0F 4
DECODER
1 0F 4
DECODER
GND
GND
A0
A1
EN
A0
A1
EN
Figure 25. IP3
Figure 26. P-1 dB
Rev. C | Page 10 of 16
Data Sheet
ADG904/ADG904-R
APPLICATIONS
The ADG904 and ADG904-R are ideal solutions for low power,
high frequency applications. The low insertion loss, high
isolation between ports, low distortion, and low current
consumption of these parts make them excellent solutions for
many high frequency switching applications. They may be used
in applications such as switchable filters, transmitters and
receivers for radar systems, and communications systems from
base stations to cell phones.
VGA
RF1
RF2
RF3
RF4
CABLE
TUNER
ADG904
ANTENNA
Figure 27. Tuner Modules
The ADG9xx wideband switches are designed to meet the
demands of devices that transmit at ISM band frequencies of
1 GHz and higher. The low insertion loss, high isolation
between ports, single pin control interface, no requirement for
dc blocking capacitors, and TTL interface compatibility of these
parts make them cost-effective and an easy-to-integrate
switching solution for many high frequency switching
applications and low power applications where the parts can
handle up to 16 dBm of power.
FILTER SELECTION
The ADG904 can be used to switch high frequency signals
between different filters and to multiplex the signal to the
output. These SP4T switches are also ideal for high speed
signal routing.
RF1
RF2
RF3
RF4
RF1
RF2
RF3
RF4
ABSORPTIVE VS. REFLECTIVE
RF
RF
OUT
IN
ADG904
ADG904
RFC
RFC
The ADG904 is an absorptive (matched) switch with 50 Ω
terminated shunt legs; the ADG904-R is a reflective switch with
0 Ω terminated shunts to ground. The ADG904 absorptive
switch has a good VSWR on each port, regardless of the switch
mode. An absorptive switch should be used when there is a
need for a good VSWR that is looking into the port but not
passing the through signal to the common port. The ADG904 is
therefore ideal for applications that require minimum
reflections back to the RF source. It also ensures that the
maximum power is transferred to the load.
Figure 28. Filter Selection
Tx/Rx SWITCHING
The low insertion loss and high isolation between ports ensure
that the ADG904 and ADG904-R are suitable transmit/receive
switches for all ISM band and wireless LAN, providing the
required isolation between the transmit signal and the
receive signal.
The ADG904-R reflective switch is suitable for applications
where high off port VSWR does not matter, and the switch has
other performance features. It may be used in many applica-
tions, including high speed filter selection. In most cases, an
absorptive switch may be used instead of a reflective switch, but
not vice versa.
Rx
ANTENNA
Rx
Rx
Rx
ADG904
Tx
ANTENNA DIVERSITY SWITCH
The ADG904 is ideal for use as an antenna diversity switch,
switching different antennas into the tuner. The low insertion
loss ensures minimum signal loss and high isolation between
channels, making these SP4T switches suitable for switching
applications in tuner modules and set-top boxes.
Figure 29. Tx/Rx Switching
Rev. C | Page 11 of 16
ADG904/ADG904-R
EVALUATION BOARD
Data Sheet
The ADG904/ADG904-R evaluation board allows designers
to evaluate the high performance, wideband switches with
minimal effort.
Only a power supply and a network analyzer, along with the
evaluation board, are required to demonstrate that these devices
meet user requirements. An application note, available with the
evaluation board, provides complete operating information.
The RFC port (see Figure 30) is connected through a 50 Ω
transmission line to the bottom left SMA connector, J4. RF1,
RF2, RF3, and RF4 are connected through 50 Ω transmission
lines to SMA connectors J5, J6, J7, and J8, respectively. A through
transmission line connects J9 and J10; this transmission line
is used to estimate the loss of the PCB over the environmental
conditions being evaluated.
Figure 30. ADG904/ADG904-R Evaluation Board Top View
The board is constructed of four-layer, FR4 material with a
dielectric constant of 4.3 and an overall thickness of 0.062 inches.
Two ground layers with grounded planes provide ground for
the RF transmission lines. The transmission lines were designed
using a coplanar waveguide with a ground plane model using
a trace width of 0.024 inches, clearance to ground plane of
0.008 inches, dielectric thickness of 0.02 inches, and a metal
thickness of 0.0021 inches.
Rev. C | Page 12 of 16
Data Sheet
ADG904/ADG904-R
OUTLINE DIMENSIONS
6.60
6.50
6.40
20
11
10
4.50
4.40
4.30
6.40 BSC
1
PIN 1
0.65
BSC
1.20 MAX
0.15
0.05
0.20
0.09
0.75
0.60
0.45
8°
0°
0.30
0.19
COPLANARITY
0.10
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-153-AC
Figure 31. 20-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-20)
Dimensions shown in millimeters
4.10
4.00 SQ
3.90
0.30
0.25
0.18
PIN 1
INDICATOR
PIN 1
INDICATOR
16
15
20
0.50
BSC
1
EXPOSED
PAD
2.30
2.10 SQ
2.00
11
5
6
10
0.65
0.60
0.55
0.20 MIN
TOP VIEW
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
0.80
0.75
0.70
0.05 MAX
0.02 NOM
COPLANARITY
0.08
SECTION OF THIS DATA SHEET.
SEATING
PLANE
0.20 REF
COMPLIANT TO JEDEC STANDARDS MO-220-WGGD-1.
Figure 32. 20-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
4 mm × 4 mm Body, Very Very Thin Quad
(CP-20-6)
Dimensions shown in millimeters
Rev. C | Page 13 of 16
ADG904/ADG904-R
Data Sheet
ORDERING GUIDE
Model1, 2
Temperature Range
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Package Description
Package Option
ADG904BCPZ
20-Lead Lead Frame Chip Scale Package [LFCSP_WQ] CP-20-6
20-Lead Lead Frame Chip Scale Package [LFCSP_WQ] CP-20-6
20-Lead Lead Frame Chip Scale Package [LFCSP_WQ] CP-20-6
20-Lead Lead Frame Chip Scale Package [LFCSP_WQ] CP-20-6
20-Lead Thin Shrink Small Outline Package [TSSOP]
20-Lead Thin Shrink Small Outline Package (TSSOP)
20-Lead Thin Shrink Small Outline Package (TSSOP)
20-Lead Thin Shrink Small Outline Package (TSSOP)
Evaluation Board
ADG904BCPZ-R-REEL
ADG904BCPZ-REEL
ADG904BCPZ-REEL7
ADG904BRUZ
RU-20
RU-20
RU-20
RU-20
ADG904BRUZ-R
ADG904BRUZ-REEL7
ADW54011Z-0REEL7
EVAL-ADG904EBZ
EVAL-ADG904REBZ
Evaluation Board
1 Z = RoHS compliant part.
2 W = Qualified for Automotive Applications.
AUTOMOTIVE PRODUCTS
The ADW54011Z model is available with controlled manufacturing to support the quality and reliability requirements of automotive
applications. Note that this automotive model may have specifications that differ from the commercial models; therefore, designers
should review the Specifications section of this data sheet carefully. Only the automotive grade product shown are available for use in
automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to
obtain the specific Automotive Reliability reports for this model.
Rev. C | Page 14 of 16
Data Sheet
NOTES
ADG904/ADG904-R
Rev. C | Page 15 of 16
ADG904/ADG904-R
NOTES
Data Sheet
©2004–2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04504–0– /13(C)
Rev. C | Page 16 of 16
相关型号：
©2020 ICPDF网 联系我们和版权申明