AD7357BRUZ-RL [ADI]
Differential Input,Dual,Simultaneous Sampling, 4.25 MSPS, 14-Bit, SAR ADC; 差分输入,双通道,同步采样, 4.25 MSPS , 14位SAR ADC型号: | AD7357BRUZ-RL |
厂家: | ADI |
描述: | Differential Input,Dual,Simultaneous Sampling, 4.25 MSPS, 14-Bit, SAR ADC |
文件: | 总17页 (文件大小:196K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Differential Input,Dual,Simultaneous
Sampling, 4.25 MSPS, 14-Bit, SAR ADC
AD7357
Preliminary Technical Data
FEATURES
FUNCTIONAL BLOCK DIAGRAM
Vdrive
Vdd
Dual 14-bit SAR ADC
Simultaneous Sampling
AD7357
Throughput rate: 4.25 MSPS Per Channel
Specified for VDD of 2.5 V
Power dissipation:
14-BIT
SUCCESSIVE
APPROXIMATION
ADC
V
V
IN
A+
A-
SDATA
A
T/H
IN
35 mW at 4.25 MSPS
On-chip reference:
BUF
BUF
2.048 V 0.5% max @ 25°C, 10ppm/°C
Dual conversion with read
High speed serial interface:
SPI®-/QSPI™-/MICROWIRE™-/DSP-compatible
−40°C to +125°C operation
Shutdown mode: 10 µA max
16-lead TSSOP package
SCLK
CS
CONTROL
LOGIC
REF
14-BIT
SUCCESSIVE
APPROXIMATION
ADC
V
IN
B+
T/H
V
IN
B-
SDATA
B
AGND
REFGND
AGND
DGND
Figure 1.
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The AD73571 is a dual, 14-bit, high speed, low power, successive
approximation ADC that operates from a single 2.5 V power supply
and features throughput rates up to 4.25 MSPS. The part contains
two ADCs, each preceded by a low noise, wide bandwidth track-
and-hold circuit that can handle input frequencies in excess of
200 MHz.
1. Two Complete ADC Functions Allow Simultaneous Sampling
and Conversion of Two Channels.
The conversion result of both channels is simultaneously
available on separate data lines or in succession on one data
line if only one serial port is available.
2. High Throughput with Low Power Consumption.
The AD7357 offers a 4.25 MSPS throughput rate with 35 mW
power consumption.
The conversion process and data acquisition use standard control
inputs allowing for easy interfacing to microprocessors or DSPs.
CS
The input signal is sampled on the falling edge of ; conversion is
also initiated at this point. The conversion time is determined by
the SCLK frequency.
3. The part features two standard successive approximation
ADCs with accurate control of the sampling instant via a
The AD7357 uses advanced design techniques to achieve very low
power dissipation at high throughput rates. With 2.5 V supply and
a 4.25 MSPS throughput rate, the part consumes 14 mA typically.
The part also offers flexible power/throughput rate management
when operating in normal mode as the quiescent current
consumption is so low.
CS
input and once off conversion control.
1 Protected by U.S. Patent No. 6,681,332
Table 1: Related Devices.
Generic
AD7356
AD7352
Resolution
Throughput Analog Input
12
12
5MSPS
3MSPS
Differential
Differential
The analog input range for the part is the differential common
mode +/- Vref/2. The AD7357 has an on-chip 2.048 V reference
that can be overdriven when an external reference is preferred.
The AD7357 is available in a 16-lead thin shrink small outline
package (TSSOP).
Rev. PrD
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2007 Analog Devices, Inc. All rights reserved.
AD7357
Preliminary Technical Data
TABLE OF CONTENTS
Revision Historyx ............................................................................. 2
ADC Transfer Function............................................................. 11
Analog Input Structure.............................................................. 11
Analog Inputs ............................................................................. 12
Modes of Operation ....................................................................... 13
Normal Mode.............................................................................. 13
Partial Power-Down Mode ....................................................... 13
Full Power-Down Mode ............................................................ 13
Power-Up Times......................................................................... 15
Serial Interface ................................................................................ 16
Outline Dimensions....................................................................... 17
Ordering Guide............................................................................... 17
Specifications..................................................................................... 3
AD7357 Specifications................................................................. 3
Timing Specifications .................................................................. 5
Absolute Maximum Ratings............................................................ 6
ESD Caution.................................................................................. 6
Pin Configuration and Function Descriptions............................. 7
Typical Performance Characteristics ............................................. 8
Terminology ...................................................................................... 9
Theory of Operation ...................................................................... 11
Circuit Information.................................................................... 11
Converter Operation.................................................................. 11
REVISION HISTORYX
09/07—Revision PrD
Rev. PrD | Page 2 of 17
Preliminary Technical Data
AD7357
SPECIFICATIONS
AD7357 SPECIFICATIONS
VDD = 2.5 +/-10% V, VDRIVE = 2.5 V to 3.3 +10% V, internal VREF = 2.048 V, unless otherwise noted, FCLKIN = 80 MHz, FSAMPLE = 4.25 MSPS;
TA = TMIN to TMAX1, unless otherwise noted.
Table 1.
Parameter
Specification
Unit
Test Conditions/Comments
DYNAMIC PERFORMANCE
Signal-to-Noise Ratio (SNR)
Signal-to-Noise and Distortion (SINAD)
Total Harmonic Distortion (THD)
Spurious Free Dynamic Range (SFDR)
Intermodulation Distortion (IMD)
Second Order Terms
Third Order Terms
Channel-to-Channel Isolation
SAMPLE AND HOLD
fIN = 1 MHz sine wave
78
77
TBD
TBD
dB min
dB min
dB max
dB max
fa = TBD Hz, fb = TBD Hz
TBD
TBD
−85
dB typ
dB typ
dB typ
fIN = TBD kHz, fNOISE = TBD kHz
Aperture Delay
Aperture Delay Matching
Aperture Jitter
5
ns max
ps max
ps typ
MHz typ
MHz typ
40
15
200
30
Full Power Bandwidth
@ 3 dB
@ 0.1 dB
DC ACCURACY
Resolution
14
2
0.ꢀꢀ
10
1
6
10
1
Bits
Integral Nonlinearity
Differential Nonlinearity
Offset Error
LSB max
LSB max
LSB max
LSB typ
LSB max
LSB max
LSB typ
LSB max
Guaranteed no missed codes to 14 bits
Offset Error Match
Gain Error
Gain Error Match
6
ANALOG INPUT
Fully Differential Input Range: Vin+ and Vin−
VCM VREF⁄2
V
VCM = common-mode voltage , Vin+ and Vin− must
remain within GND⁄VDD
DC Leakage Current
Input Capacitance
1
35
10
µA max
pF typ
pF typ
When in track
When in hold
REFERENCE INPUT/OUTPUT
VREF Input Voltage Range
DC Leakage Current
VREF Output Voltage
VREF Temperature Coefficient
VREF Long Term Stability
VREF Output Voltage Hysteresis2
VREF Noise
2.048+100mV / Vdd
1
2.048
10
100
50
TBD
TBD
TBD
V min / V max
µA max
V
ppm⁄ꢂC typ
ppm typ
ppm typ
µV Typ
0.5ꢁ max @ 25ꢂC
For 1000 hours
VREF Output Impedance
VREF Input Capacitance
LOGIC INPUTS
Ω Typ
pF typ
When in track
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
0.6 × Vdrive
0.3 × Vdrive
1
10
V min
V max
µA max
pF typ
VIN = 0 V or VDRIVE
Input Capacitance, CIN
Rev. PrD | Page 3 of 17
AD7357
Preliminary Technical Data
Parameter
Specification
Unit
Test Conditions/Comments
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Floating-State Leakage Current
Floating-State Output Capacitance
Output Coding
Vdrive-0.2
0.2
1
V min
V max
µA max
pF typ
TBD
Straight Binary
CONVERSION RATE
Conversion Time
t2 + 15.5 × tSCLK
ns
Track-and-Hold Acquisition Time
Throughput Rate
30
4.25
ns max
MSPS max
Full-scale step input
POWER REQUIREMENTS
VDD
2.5
V
VDRIVE
2.5/3.3
V min/max
IDD
Digital I⁄PS = 0 V or VDRIVE
SCLK off
Normal Mode (Operational)
Normal Mode (Static)
Partial Power-Down Mode
Full Power-Down Mode
Power Dissipation
14
7
5
mA typ
mA typ
mA typ
µA typ
10
SCLK on or off
Normal Mode (Operational)
Normal Mode (Static)
Partial Power-Down Mode
Full Power-Down Mode
35
mW typ
mW typ
mW typ
µW typ
17.5
12.5
2.5
SCLK off
SCLK on or off
1 Temperature ranges are as follows: Y Grade: −40ꢂC to +125ꢂC, B Grade: −40ꢂC to +85ꢂC.
2 See theTerminology section.
Rev. PrD | Page 4 of 17
Preliminary Technical Data
AD7357
TIMING SPECIFICATIONS
VDD = 2.5 +/-10%V, VDRIVE = 2.5 V to 3.3 +10% V, internal reference = 2.048 V, TA = TMAX to TMIN1, unless otherwise noted.
Table 2.
Parameter
Limit at TMIN, TMAX
Unit
Description
fSCLK
50
80
kHz min
MHz max
ns max
ns min
ns min
ns max
ns max
ns min
ns min
ns min
ns max
ns min
ns min
ns max
tCONVERT
tQUIET
t2
t2 +15.5 × tSCLK
5
14 bit resolution, tSCLK = 1/fSCLK
CS
Minimum time between end of serial read and next falling edge of
5
CS
to SCLK setup time
t3
TBD
TBD
0.40 tSCLK
0.40 tSCLK
TBD
TBD
TBD
TBD
TBD
CS
Delay from until DOUTA and DOUTB are three-state disabled
Data access time after SCLK falling edge
SCLK low pulse width
2
t4
t5
t6
t7
t8
tꢀ
t10
SCLK high pulse width
SCLK to data valid hold time
CS
CS
rising edge to DOUTA, DOUTB, high impedance
rising edge to falling edge pulse width
SCLK falling edge to DOUTA, DOUTB, high impedance
SCLK falling edge to DOUTA, DOUTB, high impedance
Latency
1 Conversion Latency
1 Temperature ranges are as follows: Y Grade: −40ꢂC to +125ꢂC, B Grade: −40ꢂC to +85ꢂC.
2 The time required for the output to cross 0.4 V or 2.4 V.
Rev. PrD | Page 5 of 17
AD7357
Preliminary Technical Data
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter
Rating
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
VDD to AGND, DGND, REFGND
−0.3 V to +2.8V
−0.3 V to +3.8V
+2.8V to −3.8V
−0.3 V to +0.3 V
−0.3 V to VDD + 0.3 V
−0.3V to VDRIVE + 0.3V
−0.3 V to VDRIVE + 0.3 V
10 mA
VDRIVE to AGND, DGND, REFGND
VDD to VDRIVE
AGND to DGND to REFGND
Analog Input Voltages1 to AGND
Digital Input Voltages2 to DGND
Digital Output Voltages3 to DGND
Input Current to Any Pin Except
Supplies4
Operating Temperature Range
Y Grade
−40ꢂC to +125ꢂC
−40ꢂC to +85ꢂC
−65ꢂC to +150ꢂC
150ꢂC
B Grade
Storage Temperature Range
Junction Temperature
TSSOP Package
θJA Thermal Impedance
θJC Thermal Impedance
Lead Temperature, Soldering
Reflow Temperature (10 to 30 sec)
ESD
143ꢂC/W
45ꢂC/W
255ꢂC
TBD kV
1 Analog input voltages are VINA+, VINA-, VINB+, VINB-, REFA and REFB.
2
CS
Digital input voltages are
and SCLK.
3 Digital output voltages are SDATAA and SDATAB.
4 Transient currents of up to 100 mA will not cause SCR latch up.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate
on the human body and test equipment and can discharge without detection. Although this product
features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to
high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid
performance degradation or loss of functionality.
Rev. PrD | Page 6 of 17
Preliminary Technical Data
AD7357
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
V
INA+
DRIVE
V
SCLK
SDATA
SDATA
DGND
AGND
CS
INA-
REF
A
A
B
AD7357
TOP VIEW
(Not to Scale)
REFGND
AGND
REF
B
V
INB-
V
V
INB+
DD
Figure 2. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
Mnemonic Description
ꢀ
VDD
Power Supply Input. The VDD range for the AD7357 is 2.5V +/- 5ꢁ. The supply should be decoupled to AGND
with a 0.1 µF capacitor and a 10 µF tantalum capacitor.
16
VDRIVE
CS
Logic Power Supply Input. The voltage supplied at this pin determines at what voltage the interface will
operate. This pin should be decoupled to DGND. The voltage at this pin may be different to that at VDD
.
10
Chip Select. Active low logic input. This input provides the dual function of initiating conversions on the
AD7357 and framing the serial data transfer.
SCLK
15
Serial Clock. Logic input. A serial clock input provides the SCLK for accessing the data from the AD7357. This
clock is also used as the clock source for the conversion process.
SDATAA,
SDATAB
14,13
Serial Data Outputs. The data output is supplied to each pin as a serial data stream. The bits are clocked out on
the falling edge of the SCLK input. 16 SCLK falling edges are required to access the 14 bits of data from the
AD7357. The data simultaneously appears on both data output pins from the simultaneous conversions of
both ADCs. The data stream consists of one leading zero followed by the 14 bits of conversion data followed by
a trailing zero. The data is provided MSB first. If CS is held low for 18 SCLK cycles rather than 16, then two
further trailing zeros will appear after the 14 bits of data. If CS is held low for a further 18 SCLK cycles on either
SDATAA or SDATAB , the data from the other ADC follows on the SDATA pin. This allows data from a
simultaneous conversion on both ADCs to be gathered in serial format on either SDATAA or SDATAB.
12
DGND
Digital Ground. This is the ground reference point for all digital circuitry on the AD7357. This pin should
connect to the DGND plane of a system. The DGND and AGND voltages should ideally be at the same potential
and must not be more than 0.3 V apart, even on a transient basis.
5, 11
4
AGND
Analog Ground. This is the ground reference point for all analog circuitry on the AD7357. All analog input
signals and should be referred to this AGND voltage. The AGND and DGND voltages should ideally be at the
same potential and must not be more than 0.3 V apart, even on a transient basis.
Reference Ground. This is the ground reference point for the reference circuitry on the AD7357. Any external
reference signal should be referred to this REFGND voltage. Decoupling capacitors must be placed between
this pin and the REFA and REFB pins.
Reference decoupling capacitor pins. Decoupling capacitors are connected between these pins and the
REFGND pin to decouple the reference buffer for each respective ADC. It is recommended to decouple the each
reference pin with a 10µF capacitor. Provided the output is buffered, the on-chip reference can be taken from
these pins and applied externally to the rest of the system. The nominal internal reference voltage is 2.048V
and this appears at these pins. These pins can also be overdriven by an external reference. The input voltage
range for the external reference is 2.048+100mV to Vdd.
REFGND
REFA, REFB
3, 6
1, 2
8, 7
VINA-, VINA+
VINB-, VINB+
Analog Inputs of ADC A. These analog inputs form a fully differential pair.
Analog Inputs of ADC B. These analog inputs form a fully differential pair.
Rev. PrD | Page 7 of 17
AD7357
Preliminary Technical Data
TYPICAL PERFORMANCE CHARACTERISTICS
Figure 3. Typical FFT
Figure 6. Channel to Channel Isolation
Figure 4. Typical DNL
Figure 7. Histogram of Codes
Figure 5. Typical INL
Rev. PrD | Page 8 of 17
Preliminary Technical Data
TERMINOLOGY
AD7357
Integral Nonlinearity (INL)
Common-Mode Rejection Ratio (CMRR)
The maximum deviation from a straight line passing through
the endpoints of the ADC transfer function. The endpoints of
the transfer function are zero scale, 1 LSB below the first code
transition, and full scale, 1 LSB above the last code transition.
CMRR is defined as the ratio of the power in the ADC output at
full-scale frequency, f, to the power of a 100 mV p-p sine wave
applied to the common-mode voltage of VIN+ and VIN− of
frequency fS as
CMRR (dB) = 10log (Pf/PfS)
Differential Nonlinearity (DNL)
The difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
where:
Pf is the power at frequency f in the ADC output.
PfS is the power at frequency fS in the ADC output.
Offset Error
The deviation of the first code transition (00 . . .000) to (00 . . .
001) from the ideal (that is, -VREF + 0.5 LSB).
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns to track mode at the end
of conversion. The track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within 1/2 LSB, after the end of conversion.
Offset Error Match
This is the difference in offset error between the two ADCs.
Gain Error
Signal-to-(Noise + Distortion) Ratio (SINAD)
The deviation of the last code transition (111 . . .110) to (111 . . .
111) from the ideal (that is, VREF – 1.5 LSB) after the offset error
has been adjusted out.
This is the measured ratio of signal-to-noise and distortion at
the output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals up
to half the sampling frequency (fS/2), excluding dc. The ratio is
dependent on the number of quantization levels in the
digitization process; the more levels, the smaller the
quantization noise.
Gain Error Match
The difference in gain error between the two ADCs.
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of
crosstalk between channels. It is measured by applying a full-
scale sine wave signal to one of the two channels and applying a
50 kHz signal to the other channel. The channel-to-channel
isolation is defined as the ratio of the power of the 50 kHz
signal on the converted channel to the power of the noise signal
on the other channel that appears in the FFT of this channel.
The noise frequency on the unselected channel varies from
40 kHz to 740 kHz. The noise amplitude is at 2 × VREF, while the
signal amplitude is at 1 × VREF. See Figure 6.
The theoretical signal-to-noise and distortion ratio for an ideal
N-bit converter with a sine wave input is given by
SINAD = (6.02 N + 1.76) dB
Thus, for a 12-bit converter, this is 74 dB and for a 14 bit
converter, this is 86dB.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of harmonics to the
fundamental. For the AD7356, it is defined as
Power Supply Rejection Ratio (PSRR)
2
V22 +V32 +V42 +V52 +V6
PSRR is defined as the ratio of the power in the ADC output at
full-scale frequency, f, to the power of a 100 mV p-p sine wave
applied to the ADC VDD supply of frequency fS. The frequency
of the input varies from 1 kHz to 1 MHz.
THD
where:
dB = −20log
( )
V1
PSRR (dB) = 10log(Pf/PfS)
V1 is the rms amplitude of the fundamental.
V2, V3, V4, V5, and V6 are the rms amplitudes of the second
through the sixth harmonics.
where:
Pf is the power at frequency f in the ADC output.
PfS is the power at frequency fS in the ADC output.
Rev. PrD | Page ꢀ of 17
AD7357
Preliminary Technical Data
sum of the individual distortion products to the rms amplitude
of the sum of the fundamentals expressed in dBs.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
ADCs where the harmonics are buried in the noise floor, it is a
noise peak
Thermal Hysteresis
Thermal Hysteresis is defined as the absolute maximum change
of reference output voltage after the device is cycled through
temperature from either
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities will create distortion
products at sum and difference frequencies of mfa nfb where
m, n = 0, 1, 2, 3, and so on. Intermodulation distortion terms
are those for which neither m nor n are equal to zero. For
example, the second-order terms include (fa + fb) and (fa − fb),
while the third-order terms include (2fa + fb), (2fa − fb), (fa +
2fb), and (fa − 2fb).
T_HYS+ = +25°C to TMAX to +25°C
T_HYS– = +25°C to TMIN to +25°C
It is expressed in ppm using the following equation:
V
REF (25°C) −VREF (T _ HYS)
V
HYS (ppm) =
× 106
V
REF (25°C)
where:
REF(25°C) = VREF at 25°C
VREF(T_HYS) = Maximum change of VREF at T_HYS+ or
The AD7356 is tested using the CCIF standard where two input
frequencies near the top end of the input bandwidth are used.
In this case, the second-order terms are usually distanced in
frequency from the original sine waves, while the third-order
terms are usually at a frequency close to the input frequencies.
As a result, the second- and third-order terms are specified
separately. The calculation of the intermodulation distortion is
as per the THD specification, where it is the ratio of the rms
V
T_HYS–.
Rev. PrD | Page 10 of 17
Preliminary Technical Data
AD7357
become unbalanced. Both inputs are disconnected once the
THEORY OF OPERATION
conversion begins. The control logic and charge redistribution
DACs are used to add and subtract fixed amounts of charge
from the sampling capacitor arrays to bring the comparator
back into a balanced condition. When the comparator is
rebalanced, the conversion is complete. The control logic
generates the ADC output code. The output impedances of the
sources driving the VIN+ and VIN- pins must be matched,
otherwise, the two inputs will have different settling times,
resulting in errors.
CIRCUIT INFORMATION
The AD7357 is a fast, dual, 14-bit, single-supply, successive
approximation analog-to-digital converter. The part operates
from a 2.5 V power supply and features throughput rates up to
4.25 MSPS.
The AD7357 contains two on-chip differential track-and-hold
amplifiers, two successive approximation analog-to-digital
converters and a serial interface with two separate data output
pins. They part is housed in a 16-lead TSSOP package, offering
the user considerable space-saving advantages over alternative
solutions.
CAPACITIVE
DAC
COMPARATOR
C
C
B
A
S
V
V
IN+
The serial clock input accesses data from the part, but also
provides the clock source for each successive approximation
ADC. The AD7357 has an on-chip 2.048V reference. If an
external reference is desired the internal reference can be
overdriven with a reference of value ranging from (2.048V +
100mV) to Vdd. If the internal reference is to be used elsewhere
in the system, then the reference output needs to be buffered
first. The differential analog input range for the AD7357 is VCM
SW1
SW2
CONTROL
LOGIC
SW3
S
A
B
IN–
V
REF
CAPACITIVE
DAC
Figure 9. ADC Conversion Phase
VREF∕2.
ADC TRANSFER FUNCTION
The output coding for the AD7357 is straight binary. The
designed code transitions occur at successive LSB values (1 LSB,
2 LSBs and so on). The LSB size is (2 ×VREF)/16384 for the
AD7357. The ideal transfer characteristic of the AD7357 is
shown in Figure 10.
The AD7357 features power-down options to allow power
saving between conversions. The power-down feature is
implemented via the standard serial interface, as described in
the Modes of Operation section.
CONVERTER OPERATION
The AD7357 has two successive approximation analog-to-
digital converters, each based around two capacitive DACs.
Figure 8 and Figure 9 show simplified schematics of one of
these ADCs in acquisition and conversion phase, respectively.
The ADC is comprised of control logic, a SAR, and two
capacitive DACs. In Figure 8 (the acquisition phase), SW3 is
closed, SW1 and SW2 are in position A, the comparator is held
in a balanced condition, and the sampling capacitor arrays may
acquire the differential signal on the input.
111...111
111...110
111...101
000...010
000...001
000...000
CAPACITIVE
DAC
–V
+1 LSB
+V
–1 LSB
COMPARATOR
REF
+0.5 LSB
REF
–1.5 LSB
C
C
B
A
S
–V
+V
REF
REF
V
V
IN+
ANALOG INPUT
SW1
SW2
CONTROL
LOGIC
SW3
S
Figure 10. AD7356 Ideal Transfer Characteristic
A
B
IN–
ANALOG INPUT STRUCTURE
V
REF
Figure 11 shows the equivalent circuit of the analog input
structure of the AD7357. The four diodes provide ESD
CAPACITIVE
DAC
protection for the analog inputs. Care must be taken to ensure
that the analog input signals never exceed the supply rails by
more than 300mV. This causes these diodes to become forward-
biased and start conducting into the substrate. These diodes can
Figure 8. ADC Acquisition Phase
When the ADC starts a conversion (Figure 9), SW3 opens and
SW1 and SW2 move to Position B, causing the comparator to
Rev. PrD | Page 11 of 17
AD7357
Preliminary Technical Data
conduct up to 10mA without causing irreversible damage to the
part.
be tolerated. The THD increases as the source impedance
increases and performance degrades. Figure 12 shows a graph
of the THD vs. the analog input signal frequency for different
source impedances.
The C1 capacitors in Figure 11 are typically TBD pF and can
primarily be attributed to pin capacitance. The resistors are
lumped components made up of the on resistance of the
switches. The value of these resistors is typically about TBD Ω.
The C2 capacitors are the ADC’s sampling capacitors with a
capacitance of TBD pF typically.
Figure 13 shows a graph of the THD vs. the analog input
frequency while sampling at 4.25 MSPS. In this case the source
impedance is TBD Ω.
V
DD
D
D
C2
R1
V
IN+
C1
V
DD
D
D
C2
R1
V
IN–
C1
Figure 13.THD vs. Analog Input Frequency
Figure 11.Equivalent Analog Input Circuit,
Conversion Phase – Switches Open, Track Phase – Switches Closed
ANALOG INPUTS
Differential signals have some benefits over single-ended
signals, including noise immunity based on the devices
common-mode rejection and improvements in distortion
performance.
For ac applications, removing high frequency components from
the analog input signal is recommended by the use of an RC
low-pass filter on the analog input pins. In applications where
harmonic distortion and signal-to-noise ratio are critical, the
analog input should be driven from a low impedance source.
Large source impedances significantly affect the ac performance
of the ADC and may necessitate the use of an input buffer
amplifier. The choice of the op amp will be a function of the
particular application.
The amplitude of the differential signal is the difference
between the signals applied to the VIN+ and VIN- pins in each
differential pair (VIN+ - VIN-). VIN+ and VIN- should be
simultaneously driven by two signals each of amplitude VREF
that are 180° out of phase. This amplitude of the differential
signal is, therefore –VREF to +VREF peak-to –peak regardless of
the common mode (CM).
The common mode is the average of the two signals and is
therefore the voltage on which the two inputs are centered.
CM = (VIN+ + VIN-)/2
This results in the span of each input being CM VREF/2. This
voltage has to be set up externally. When a conversion takes
place, the common mode is rejected resulting in a virtually
noise free signal of amplitude –VREF to +VREF corresponding to
the digital codes of 0 to 16383 for the AD7357.
Figure 12.THD vs. Analog Input Frequency for Various Source Impedances
When no amplifier is used to drive the analog input, the source
impedance should be limited to low values. The maximum
source impedance will depend on the amount of THD that can
Rev. PrD | Page 12 of 17
Preliminary Technical Data
AD7357
Once a data transfer is complete and SDATAA and SDATAB have
returned to three-state, another conversion can be initiated after
MODES OF OPERATION
The mode of operation of the AD7357 is selected by controlling
CS
the quiet time, tQUIET, has elapsed by bringing
low again
CS
the (logic) state of the
signal during a conversion. There are
(assuming the required acquisition time has been allowed).
three possible modes of operation: normal mode, partial power-
down mode and full power-down mode. After a conversion has
PARTIAL POWER-DOWN MODE
This mode is intended for use in applications where slower
throughput rates are required. Either the ADC is powered down
between each conversion, or a series of conversions may be
performed at a high throughput rate and the ADC is then
powered down for a relatively long duration between these
bursts of several conversions. When the AD7357 is in partial
power-down, all analog circuitry is powered down except for
the on-chip reference and reference buffers.
CS
been initiated, the point at which
which power-down mode, if any, the device enters. Similarly, if
CS
is pulled high determines
already in a power-down mode,
can control whether the
device returns to normal operation or remains in power-down.
These modes of operation are designed to provide flexible
power management options. These options can be chosen to
optimize the power dissipation/throughput rate ratio for the
differing application requirements.
To enter partial power, the conversion process must be
NORMAL MODE
nd
CS
interrupted by bringing
high anywhere after the 2 falling
This mode is intended for applications needing fastest
throughput rates since the user does not have to worry about
any power-up times with the AD7357 remaining fully powered
at all times. Figure 14 shows the general diagram of the
operation of the AD7357 in this mode.
edge of SCLK and before the 10th falling edge of SCLK, as
CS
shown in Figure 15. Once
window of SCLKs, the part enters partial power-down, the
CS
has been brought high in this
conversion that was initiated by the falling edge of
is
terminated, and SDATAA and SDATAB go back into three-state.
nd
CS
CS
If
is brought high before the 2 SCLK falling edge, the part
remains in normal mode and does not power down. This avoids
1
10
14
CS
accidental power-down due to glitches on the
line.
SCLK
D
D
A
B
OUT
OUT
CS
LEADING ZEROS + CONVERSION RESULT
1
2
10
14
Figure 14. Normal Mode Operation
SCLK
CS
The conversion is initiated on the falling edge of , as
D
D
A
B
THREE-STATE
OUT
OUT
described in the Serial Interface section. To ensure that the part
CS
remains fully powered up at all times,
must remain low until
at least 10 SCLK falling edges have elapsed after the falling edge
Figure 15. Entering Partial Power-Down Mode
th
CS CS
of . If
is brought high any time after the 10 SCLK falling
To exit this mode of operation and power up the AD7357 again,
a dummy conversion is performed. On the falling of , the
edge but before the 16th SCLK falling edge, the part remains
powered up, but the conversion is terminated and SDATAA and
SDATAB go back into three-state. 16 serial clock cycles are
required to complete the conversion and access the conversion
result for the AD7357. The SDATA lines do not return to three-
state after 16 SCLK cycles have elapsed, but instead do so when
CS
device begins to power up, and continues to power up as long as
th
CS
is held low until after the falling edge of the 10 SCLK. The
device is fully powered up after approximately TBD μs has
elapsed, and valid data results from the next conversion, as
nd
CS
shown in Figure 16. If
is brought high before the 2 falling
CS
CS
is brought high again. If
is left low for another 2 SCLK
CS
edge of SCLK, the AD7357 again goes into partial power-down.
CS
cycles, two trailing zeros are clocked out after the data. If
is
This avoids accidental power-up due to glitches on the
Although the device may begin to power up on the falling edge
CS CS
line.
left low for a further 16 SCLK cycles, the result for the other
ADC on board is also accessed on the same SDATA line as
shown in Figure 20 (see the Serial Interface section).
of , it powers down again on the rising edge of . If the
CS
AD7357 is already in partial power-down mode and
is
brought high between the 2nd and 10th falling edges of SCLK, the
device enters full power-down mode.
Once 32 SCLK cycles have elapsed, the SDATA line returns to
nd
CS
three-state on the 32 SCLK falling edge. If
is brought high
prior to this, the SDATA line returns to three-state at that point.
CS
high again sometime prior to the next conversion if so desired,
since the bus still returns to three-state upon completion of the
dual result read.
FULL POWER-DOWN MODE
Thus,
may idle low after 32 SCLK cycles until it is brought
This mode is intended for use in applications where throughput
rates slower than those in the partial power-down mode are
required, as power-up from a full power-down takes
substantially longer than that from a partial power-down. This
Rev. PrD | Page 13 of 17
AD7357
Preliminary Technical Data
mode is more suited to applications where a series of
has been brought high in this window of SCLKs, the part
completely powers down.
conversions performed at a relatively high throughput rate are
followed by a long period of inactivity and thus, power-down.
When the AD7357 is in full power-down, all analog circuitry is
powered down. Full power-down is entered in a similar way as
partial power-down, except the timing sequence shown in
Figure 15 must be executed twice. The conversion process must
CS
Note that it is not necessary to complete the 16 SCLKs once
has been brought high to enter a power-down mode.
To exit full power-down mode and power-up the AD7357, a
dummy conversion is performed, as when powering up from
CS
CS
be interrupted in a similar fashion by bringing
high
partial power-down. One the falling edge of
, the device
anywhere after the 2nd falling edge of SCLK and before the 10th
falling edge of SCLK. The device enters partial power down at
this point.
CS
begins to power up, as long as
is held low until after the
falling edge of the 10th SCLK. The required power-up time must
elapse before a conversion can be initiated, as shown in Figure
18.
To reach full power-down, the next conversion cycle must be
CS
interrupted in the same way, as shown in Figure 17. Once
THE PART IS FULLY
POWERED UP; SEE
POWER-UP TIMES
SECTION.
THE PART BEGINS
TO POWER UP.
tPOWER-UP1
CS
1
10
14
1
14
SCLK
D
D
A
B
OUT
INVALID DATA
VALID DATA
OUT
Figure 16. Exiting Partial Power-Down Mode
THE PART ENTERS
PARTIAL POWER DOWN.
THE PART BEGINS
TO POWER UP.
THE PART ENTERS
FULL POWER DOWN.
CS
1
2
10
14
1
2
10
14
SCLK
D
D
A
B
THREE-STATE
THREE-STATE
OUT
INVALID DATA
INVALID DATA
OUT
Figure 17. Entering Full Power-Down Mode
THE PART IS FULLY POWERED UP,
SEE POWER-UP TIMES SECTION.
THE PART BEGINS
TO POWER UP.
tPOWER-UP2
CS
14
14
10
1
1
SCLK
D
D
A
B
OUT
INVALID DATA
VALID DATA
OUT
Figure 18. Exiting Full Power-Down Mode
Rev. PrD | Page 14 of 17
Preliminary Technical Data
AD7357
When power supplies are first applied to the AD7357, the ADC
can power up in either of the power-down modes or in normal
mode. Because of this, it is best to allow a dummy cycle to
elapse to ensure that the part is fully powered up before
attempting a valid conversion. Likewise, if the part is to be kept
in partial power-down mode immediately after the supplies are
applied, then two dummy cycles must be initiated. The first
POWER-UP TIMES
The AD7357 has two power-down modes, partial power-down
and full power-down, which are described in detail in the
previous sections. This section deals with the power-up time
required when coming out of either of these modes.
To power up from partial power-down mode, one dummy cycle
is required. The device is fully powered up after approximately
TBD µs from the falling edge of
dummy cycle must hold
low until after the 10th SCLK falling
CS
edge; in the second cycle,
must be brought high between the
CS
has elapsed. Once the
CS
second and 10th SCLK falling edges (see Figure 15).
partial power-up time has elapsed, the ADC is fully powered up
and the input signal is acquired properly. The quiet time, tQUIET
must still be allowed from the point where the bus goes back
into three-state after the dummy conversion to the next falling
,
Alternatively, if the part is to be placed into full power-down
mode when the supplies are applied, three dummy cycles must
be initiated. The first dummy cycle must hold
low until after
CS
edge of
.
CS
the 10th SCLK falling edge; the second and third dummy cycles
place the part into full power-down mode (see Figure 17). See
the Modes of Operation section.
To power up from full power-down, approximately TBD μs
should be allowed from the falling edge of , shown in Figure
CS
18 as tPOWER-UP2
.
Note that during power-up from partial power-down mode, the
track-and-hold, which is in hold mode while the part is powered
down, returns to track mode after the first SCLK edge that the
part receives after the falling edge of
.
CS
Rev. PrD | Page 15 of 17
AD7357
Preliminary Technical Data
SERIAL INTERFACE
Figure 19 shows the detailed timing diagram for serial
interfacing to the AD7357. The serial clock provides the
conversion clock and controls the transfer of information from
the AD7357 during conversion.
A minimum of 16 serial clock cycles are required to perform
the conversion process and to access data from one conversion
CS
on either data line of the AD7357.
going low provides the
leading zero to be read in by the microcontroller or DSP. The
remaining data is then clocked out by subsequent SCLK falling
edges, beginning with a second leading zero. Thus, the first
falling clock edge on the serial clock has the leading zero
provided and also clocks out the second leading zero. The 14-bit
result then follows with the final bit in the data transfer valid on
the 16th falling edge, having being clocked out on the previous
(15th) falling edge. In applications with a slower SCLK, it may be
possible to read in data on each SCLK rising edge depending on
CS
The
signal initiates the data transfer and conversion process.
CS
The falling edge of
puts the track and hold into hold mode at
which point the analog input is sampled and the bus is taken
out of three-state. The conversion is also initiated at this point
and requires a minimum of 16 SCLKs to complete. Once 15
SCLK falling edges have elapsed, the track and hold will go back
into track on the next SCLK rising edge, as shown in Figure 19
at point B. On the rising edge of , the conversion will be
terminated and SDATAA and SDATAB will go back into three-
CS
CS
the SCLK frequency. The first rising edge of SCLK after the
falling edge would have the second leading zero provided, and
the 15th rising SCLK edge would have DB0 provided.
CS
state. If
is not brought high, but is instead held low for a
further 16 SCLK cycles on SDATAA, the data from the
conversion on ADCB will be output on SDATAA.
CS
Likewise, if
is held low for a further 16 SCLK cycles on
SDATAA, the data from the conversion on ADCA will be output
on SDATAB. This is illustrated in Figure 20 where the case for
SDATAA is shown. In this case, the SDATA line in use will go
back into three-state on the 32nd SCLK falling edge or the rising
CS
edge of , which ever occurs first.
tACQUISITION
CS
t9
tCONVERT
t2
t6
B
SCLK
3
4
5
1
2
15
16
t5
t8
t7
t3
t4
tQUIET
D
D
A
B
OUT
OUT
0
DB13
DB12
DB2
DB0
0
0
DB11
DB10
DB1
THREE-STATE
THREE-
STATE
2 LEADING ZEROS
Figure 19. Serial Interface Timing Diagram
CS
t6
t2
SCLK
3
4
5
1
2
15
16
17
18
32
31
t5
t3
t4
t7
DB13
DB12
DB12
B
0
DB11
DB0
0
0
0
DB13
0
DB1
B
DB0
B
B
D
A
A
A
A
A
OUT
THREE-
STATE
THREE-
STATE
2 ZEROS
2 LEADING
ZEROS
Figure 20. Reading Data from Both ADCs on One SDATA Line with 32 SCLKs
Rev. PrD | Page 16 of 17
Preliminary Technical Data
OUTLINE DIMENSIONS
AD7357
5.10
5.00
4.90
16
9
8
4.50
4.40
4.30
6.40
BSC
1
PIN 1
1.20
MAX
0.15
0.05
0.20
0.09
0.75
0.60
0.45
8°
0°
0.30
0.19
0.65
BSC
SEATING
PLANE
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 21. 16-LeadThin Shrink Small Outline Package
Dimensions shown in millimeters
ORDERING GUIDE
Model
Temperature Range
−40ꢂC to +85ꢂC
Package Description
Package Option
AD7357BRUZ
16-Lead TSSOP
16-Lead TSSOP
16-Lead TSSOP
16-Lead TSSOP
16-Lead TSSOP
16-Lead TSSOP
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
AD7357BRUZ-500RL7
AD7357BRUZ-RL
AD7357YRUZ
AD7357YRUZ-500RL7
AD7357YRUZ-RL
−40ꢂC to +85ꢂC
−40ꢂC to +85ꢂC
−40ꢂC to +125ꢂC
−40ꢂC to +125ꢂC
−40ꢂC to +125ꢂC
©2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
PR06003-0-9/07(PrD)
Rev. PrD | Page 17 of 17
相关型号:
©2020 ICPDF网 联系我们和版权申明