TLD5095ELXUMA1 [INFINEON]
Switching Controller, Current-mode, 0.09A, 500kHz Switching Freq-Max, PDSO14, GREEN, PLASTIC, SSOP-14;型号: | TLD5095ELXUMA1 |
厂家: | Infineon |
描述: | Switching Controller, Current-mode, 0.09A, 500kHz Switching Freq-Max, PDSO14, GREEN, PLASTIC, SSOP-14 开关 光电二极管 |
文件: | 总35页 (文件大小:634K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Infineon® LITIX™ Power
Multitopology LITIXTM Power DC/DC Controller IC
TLD5095EL
Infineon® LITIX™ Power
Multitopology LITIXTM Power DC/DC Controller IC
Data Sheet
Revision 1.4
2015-03-11
Automotive Power
Infineon® LITIX™ Power
TLD5095EL
Table of Contents
Table of Contents
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1
2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3
3.1
3.2
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin Definitions and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4
General Product Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Functional Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Thermal Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.1
4.2
4.3
5
5.1
5.2
Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6
6.1
6.2
Oscillator and Synchronisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Electrical Characteristics Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Typical Performance Characteristics of Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7
Enable and Dimming Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.1
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8
Linear Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
8.1
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
9
9.1
9.2
Protection and Diagnostic Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
10
Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
10.1
Further Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
11
Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Data Sheet
2
Revision 1.4 2015-03-11
Not for Customers
TLD5095EL
Infineon® LITIX™ Power
1
Overview
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Wide Input Voltage Range from 4.75 V to 45 V
Constant Current or Constant Voltage Regulation
Drives LEDs in Boost, Buck, Buck-Boost, SEPIC and Flyback
Topology
Very Low Shutdown Current: IQ< 10 µA
Flexible Switching Frequency Range, 100 kHz to 500 kHz
Synchronization with external clock source
Output Open Circuit Diagnostic Output
PWM Dimming
PG-SSOP-14
Internal Soft Start
300mV High Side Current Sense to ensure highest flexibility and LED current accuracy
Internal 5 V Low Drop Out Voltage Regulator
Wide LED current range via simple adaptation of external components
Available in a small thermally enhanced PG-SSOP-14 package
Output Overvoltage Protection
Over Temperature Shutdown
Automotive AEC Qualified
Green Product (RoHS) Compliant
Description
The TLD5095EL is a smart multitopology LED controller with built in protection and diagnostic features. The main
function of this device is to regulate a constant LED current. The constant current regulation is especially beneficial for
LED color accuracy and longer lifetime. The controller concept of the TLD5095EL allows a multi-purpose usage such as
Boost, Buck, Buck-Boost, SEPIC and Flyback configuration with various load current levels by simply adjusting the
external components. The TLD5095EL has a PWM output for dimming a LED load. The diagnostics are communicated
on a status output (pin ST) to indicate a fault condition such as an LED open circuit. The switching frequency is adjustable
in the range of 100 kHz to 500 kHz and can be synchronized to an external clock source. The TLD5095EL features an
enable function reducing the shut-down current consumption to <10 µA. The current mode regulation scheme of this
device provides a stable regulation loop maintained by small external compensation components. The integrated soft-
start feature limits the current peak as well as voltage overshoot at start-up. This IC is suited for use in the harsh
automotive environments and provides protection functions such as output overvoltage protection and
overtemperature shutdown.
Application
•
Automotive Exterior and Interior Lighting
Type
Package
Marking
TLD5095EL
Data Sheet
PG-SSOP-14
TLD5095
3
Revision 1.4, 2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Block Diagram
2
Block Diagram
IN
IVCC
SWO
14
LDO
1
Power On
Reset
Internal
Supply
EN_INT/
PWM_INT
EN / PWMI
On/Off
Logic
13
Power Switch
Gate Driver
Soft
Start
2
FREQ/
Oscillator
PWM
Generator
SYNC 11
SWCS
SGND
Slope
Comp.
4
Switch Current
Error Amplifier
3
Leading Edge
Blanking
Thermal
Protection
ST
Diagnostics
Logic
OVFB
FBH
10
Over Volage
Protection
9
Open Load
Detection
6
7
COMP
Feedback Voltage
Error Amplifier
8
FBL
PWMO
EN_INT/
PWM_INT
Dimming Switch
Gate Driver
5
12
BlockDiagram .vsd
GND
Figure 2-1 Block Diagram TLD5095EL
Data Sheet
4
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Pin Configuration
3
Pin Configuration
3.1
Pin Assignment
1
2
3
4
5
6
7
14
13
12
11
10
9
IVCC
SWO
IN
EN/PWMI
GND
SGND
SWCS
FREQ/SYNC
PWMO
FBH
ST
OVFB
COMP
EP
FBL
8
Figure 3-1 Pin Configuration TLD5095EL
3.2
Pin Definitions and Functions
Table 3-1
Pin Definition and Function
#
Symbol
Direction Type
Function
1
IVCC
Internal LDO Output;
Used for internal biasing and gate drive. Bypass with
external capacitor. Pin must not left open.
2
3
4
5
6
7
SWO
SGND
SWCS
PWMO
FBH
Switch Output;
Connect to gate of external switching MOSFET
Current Sense Ground;
Ground return for current sense switch
Current Sense Input;
Detects the peak current through switch
PWM Dimming Output;
Connect to gate of external MOSFET
Voltage Feedback Positive;
Non inverting Input (+)
FBL
Voltage Feedback Negative;
Inverting Input (-)
Data Sheet
5
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Pin Configuration
Table 3-1
Pin Definition and Function
Direction Type
#
Symbol
Function
8
COMP
Compensation Input;
Connect R and C network to pin for stability
9
OVFB
Output Overvoltage Protection Feedback;
Connect to resistive voltage divider to set overvoltage
threshold.
10 ST
Status Output;
Open drain diagnostic output to indicate fault condition.
Connect pull up resistor to pin.
11 FREQ / SYNC
Frequency Select or Synchronization Input;
Connect external resistor to GND to set frequency.
Or apply external clock signal for synchronization within
frequency capture range.
12 GND
Ground;
Connect to system ground.
13 EN / PWMI
Enable or PWM Input;
Apply logic high signal to enable device or PWM signal for
dimming LED.
14 IN
15 EP
Supply Input;
Supply for internal biasing.
Exposed Pad;
Connect to external heat spreading Cu area with
electrically GND (e.g. inner GND layer of multilayer PCB
with thermal vias)
Data Sheet
6
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
General Product Characteristics
4
General Product Characteristics
4.1
Absolute Maximum Ratings
Tj = -40°C to +150°C; all voltages with respect to ground (unless otherwise specified)
Table 4-1
Absolute Maximum Ratings1)
Symbol
Parameter
Values
Typ.
Unit Note or
Test Condition
Number
Min.
Max.
Voltages
IN
VIN
-0.3
-40
45
45
5.5
V
V
V
P_4.1.1
P_4.1.2
P_4.1.3
Supply Input
EN / PWMI
Enable or PWM Input
VEN
FBH-FBL;
VFBH-VFBL
-5.5
Feedback Error Amplifier
Differential
FBH;
VFBH
-0.3
-0.3
45
45
V
V
P_4.1.4
P_4.1.5
Feedback Error Amplifier
Positive Input
FBL
VFBL
Feedback Error Amplifier
Negative Input
OVFB
VOVP
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
5.5
45
V
V
V
V
V
V
V
V
V
P_4.1.6
P_4.1.7
P_4.1.8
P_4.1.9
P_4.1.10
P_4.1.11
P_4.1.12
P_4.1.13
P_4.1.14
Over Voltage Feedback Input
OVFB
VOVP
t < 10s
t < 10s
t < 10s
Over Voltage Feedback Input
SWCS
VSWCS
VSWCS
VSWO
VSWO
VSGND
VCOMP
VCOMP
5.5
6.2
5.5
6.2
0.3
5.5
6.2
Switch Current Sense Input
SWCS
Switch Current Sense Input
SWO
Switch Gate Drive Output
SWO
Switch Gate Drive Output
SGND
Current Sense Switch GND
COMP
Compensation Input
COMP
t < 10s
Compensation Input
Data Sheet
7
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
General Product Characteristics
Table 4-1
Absolute Maximum Ratings1)
Symbol
Parameter
Values
Typ.
Unit Note or
Test Condition
Number
Min.
Max.
FREQ / SYNC; Frequency and VFREQ / SYNC -0.3
Synchronization Input
5.5
V
V
V
V
P_4.1.15
P_4.1.16
P_4.1.17
P_4.1.18
FREQ / SYNC; Frequency and VFREQ / SYNC -0.3
Synchronization Input
6.2
5.5
6.2
t < 10s
t < 10s
PWMO
PWM Dimming Output
VPWMO
VPWMO
-0.3
-0.3
PWMO
PWM Dimming Output
ST
VST
IST
-0.3
-5
45
5
V
P_4.1.19
P_4.1.20
P_4.1.21
Diagnostic Status Output
mA
V
IVCC
VIVCC
-0.3
5.5
Internal Linear Voltage
Regulator Output
IVCC
VIVCC
-0.3
6.2
V
t < 10s
P_4.1.22
Internal Linear Voltage
Regulator Output
Temperatures
Junction Temperature
Storage Temperature
ESD Susceptibility
ESD Resistivity to GND
ESD Resistivity to GND
Tj
-40
-55
150
150
°C
°C
P_4.1.23
P_4.1.24
Tstg
VESD,HBM
VESD,CDM
VESD,CDM,C
-2
2
kV
V
HBM2)
CDM3)
CDM3)
P_4.1.25
P_4.1.26
P_4.1.27
-500
-750
500
750
ESD Resistivity Pin 1,7,8,14
(corner pins) to GND
V
1) Not subject to production test, specified by design.
2) ESD susceptibility, Human Body Model “HBM” according to ANSI/ESDA/JEDEC JS-001 (1.5kW, 100pF)
3) ESD susceptibility, Charged Device Model “CDM” ESDA STM5.3.1 or ANSI/ESD S.5.3.1
Note:
1. Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
2. Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions are
not designed for continuous repetitive operation.
Data Sheet
8
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
General Product Characteristics
4.2
Functional Range
Table 4-2
Functional Range
Symbol
Parameter
Values
Typ.
Unit Note or
Test Condition
Number
Min.
4.75
4.5
Max.
45
Supply Voltage
VIN
V
V
V
IVCC > VIVCC,RTH,d P_4.2.1
Feedback Voltage
Input
V
FBH; VFBL
45
P_4.2.2
Junction
Tj
-40
150
°C
P_4.2.3
Temperature
Note: Within the functional range the IC operates as described in the circuit description. The electrical
characteristics are specified within the conditions given in the related electrical characteristics table.
4.3
Thermal Resistance
Note: This thermal data was generated in accordance with JEDEC JESD51 standards.
For more information, go to www.jedec.org.
Table 4-3
Thermal Resistance
Symbol
Parameter
Values
Typ.
10
Unit Note or
Test Condition
Number
Min.
Max.
Junction to Case1)2) RthJC
Junction to Ambient3) RthJA
Junction to Ambient RthJA
Junction to Ambient RthJA
K/W
K/W
K/W
K/W
P_4.3.1
P_4.3.2
P_4.3.3
P_4.3.4
42
2s2p
42
1s0p + 600mm2
1s0p + 300mm2
42
1) Not subject to production test, specified by design.
2) Specified RthJC value is simulated at natural convection on a cold plate setup (all pins and the exposed pad are fixed to
ambient temperature). Ta=25°C is dissipating 1W.
3) Specified RthJA value is according to JEDEC 2s2p (JESD 51-7) + (JESD 51-5) and JEDEC 1s0p (JESD 51-3) + heatsink
area at natural convection on FR4 board; The device was simulated on a 76.2 x 114.3 x 1.5mm board. The 2s2p board
has 2 outer copper layers (2 x 70µm Cu) and 2 inner copper layers (2 x 35µm Cu), A thermal via (diameter = 0.3mm and
25µm plating) array was applied under the exposed pad and connected the first outer layer (top) to the first inner layer and
second outer layer (bottom) of the JEDEC PCB. Ta=25°C, IC is dissipating 1W
Data Sheet
9
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Regulator
5
Regulator
5.1
Description
The TLD5095 regulator is suitable for Boost, Buck, Buck-Boost, SEPIC and Flyback configurations. The
constant output current is especially useful for light emitting diode (LED) applications. The regulator function
is implemented by a pulse width modulated (PWM) current mode controller.
The PWM current mode controller uses the peak current through the external power switch and error in the
output current to determine the appropriate pulse width duty cycle (on time) for constant output current. The
current mode controller it provides a PWM signal to an internal gate driver which then outputs the same PWM
signal to external n-channel enhancement mode metal oxide field effect transistor (MOSFET) power switch.
The current mode controller also has built-in slope compensation to prevent sub-harmonic oscillations which
is a characteristic of current mode controllers operating at high duty cycles (>50% duty).
An additional built-in feature is an integrated soft start that limits the current through the inductor and
external power switch during initialization. The soft start function gradually increases the inductor and switch
current over 1 ms (typical) to minimize potential overvoltage at the output.
TLD5095
OV FB
H when
OVFB >1.25V
OVFB
VRef
=
1.25V
High when
UV IVCC
IVCC < 4.0V
COMP
FBH
VRef
4.0V
=
NOR
Current
Comp
Gate Driver
Supply
x1
IVCC
SWO
EA
Output Stage
OFF when
Low
gmEA
IEA
High when
lEA - ISLOPE - ICS > 0
>
1
INV
R
S
OFF
when H
FBL
Q
Q
1
&
&
Gate
Driver
Low when
R
VRef
0.3V
=
Soft start
Tj > 175 °C
Q
&
&
Current
Sense
PWM-FF
Oscillator
Slope Comp
I
SWCS
SGND
NAND 2
S
t
Q
FREQ/
SYNC
ICS
&
Error-FF
Clock
Figure 5-1 Block Diagram Buck Regulator
Data Sheet
10
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Regulator
5.2
Electrical Characteristics
VIN = 6 V to 40 V; 4.5V≤ VFBH ≤ 40V, 4.5V ≤ VFBL ≤ 40V, Tj = -40°C to +150°C, all voltages with respect to ground,
positive current flowing into pin; (unless otherwise specified)
Table 5-1
Electrical Characteristics: Buck Regulator
Parameter
Symbol
Values
Typ.
Unit Note or
Test Condition
Number
Min.
Max.
Regulator
Feedback Reference VREF
Voltage
0.28
–
0.30
–
0.32
0.15
V
VIN = 19 V;
REF= VFBH -VFBL
VIN = 6 to 19 V;
BO= 30 V;
BO = 500 mA
P_5.2.1
P_5.2.2
V
Voltage Line
Regulation
Δ
/ΔVIN
VREF
%/V
V
I
Figure 10-11
VIN = 6 V;
Voltage Load
Regulation
(ΔVREF
/
–
–
5
%/A
P_5.2.3
P_5.2.4
V
BO = 30V;
VREF
)
I
BO = 100 to 500 mA
/ΔIBO
Figure 10-11
Switch Peak Over
Current Threshold
VSWCS
130
90
150
93
170
95
mV
%
VIN = 6 V
VFBH = VFBL = 5 V
V
COMP = 3.5V
Maximum Duty Cycle DMAX,fixed
Maximum Duty Cycle DMAX,sync
Fixed frequency
mode
P_5.2.5
P_5.2.6
Synchronization
mode
88
–
–
%
Soft Start Ramp
tSS
350
1000
1500
µs
V
FB rising from 5% P_5.2.7
to 95% of VFB, typ.
Feedback Input
Current
IFBx
ISWCS
-10
10
-50
50
–
-100
100
–
µA
µA
V
V
V
FBH - VFBL = 0.3 V P_5.2.8
Switch Current
Sense Input Current
SWCS = 150 mV
P_5.2.9
Input Undervoltage VIN,off
Shutdown
3.75
–
VIN decreasing
VIN increasing
P_5.2.10
P_5.2.11
Input Voltage
Startup
VIN,on
–
4.75
V
Gate Driver for External Switch
Gate Driver Peak
ISWO,SRC
–
–
–
380
550
30
–
mA
mA
ns
V
V
SWO = 3.5V
SWO = 1.5V
P_5.2.12
P_5.2.13
P_5.2.14
Sourcing Current1)
Gate Driver Peak
Sinking Current
ISWO,SNK
–
Gate Driver Output tR,SWO
60
CL,SWO = 3.3nF;
Rise Time
VSWO = 1V to 4V
Data Sheet
11
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Regulator
Table 5-1
Electrical Characteristics: Buck Regulator
Parameter
Symbol
Values
Typ.
20
Unit Note or
Test Condition
Number
Min.
Max.
Gate Driver Output tF,SWO
Fall Time
Gate Driver Output
Voltage
–
40
ns
CL,SWO = 3.3nF;
P_5.2.15
P_5.2.16
VSWO = 1V to 4V
VSWO
4.5
–
5.5
V
CL,SWO = 3.3nF
1) Not subject to production test, specified by design
Data Sheet
12
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Oscillator and Synchronisation
6
Oscillator and Synchronisation
Description
R_OSC vs. switching frequency
The internal oscillator is used to determine the switching frequency of the multitopology regulator. The
switching frequency can be selected from 100 kHz to 500 kHz with an external resistor to GND. To set the
switching frequency with an external resistor the following formula can be applied.
(6.1)
1
3
R FREQ
=
−
(3.5 ⋅10
[Ω
]
)[ ]
Ω
s
⎛
1
⎞
⎟
⎡
⎤
⎡
⎤
−12
(141 ⋅10
) ⋅ ⎜ f FREQ
⎢
⎣
⎥
⎦
⎢
⎣
⎥
⎦
Ω
s
⎝
⎠
In addition, the oscillator is capable of changing from the frequency set by the external resistor to a synchronized
frequency from an external clock source. If an external clock source is provided on the pin FREQ/SYNC, then the
internal oscillator synchronizes to this external clock frequency and the multitopology regulator switches at the
synchronized frequency. The synchronization frequency capture range is 250 kHz to 500 kHz.
TLD5095
FREQ
/ SYNC
Oscillator
PWM
Logic
Gate
Driver
SWO
Multiplexer
Clock Frequency
Detector
VCLK
RFREQ
Oscillator_BlkDiag_SyncFixedMode .vsd
Figure 6-1 Oscillator and Synchronization Block Diagram and Simplified Application Circuit
TSYNC = 1 / fSYNC
VSYNC
tSYNC,PWH
VSYNC,H
VSYNC,L
t
Figure 6-2 Synchronization Timing Diagram
Data Sheet
13
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Oscillator and Synchronisation
6.1
Electrical Characteristics Oscillator
VIN = 6 V to 40 V; 4.5V ≤ VFBH ≤ 40V, 4.5V ≤ VFBL ≤ 40V, Tj = -40°C to +150°C, all voltages with respect to ground,
positive current flowing into pin; (unless otherwise specified)
Table 6-1
Electrical Characteristics
Parameter
Symbol
Min.
Values
Typ.
Unit Note or
Test Condition
Number
Max.
Oscillator
Oscillator Frequency fFREQ
250
100
300
–
350
500
kHz
kHz
R
FREQ = 20kΩ
P_6.1.1
P_6.1.2
Oscillator Frequency fFREQ
17% internal
Adjustment Range
tolerance + external
resistor tolerance
FREQ / SYNC Supply IFREQ
Current
–
–
-700
1.32
µA
V
V
FREQ = 0 V
P_6.1.3
P_6.1.4
Frequency Voltage
VFREQ
1.16
1.24
fFREQ = 100 kHz
Synchronisation
Synchronization
Frequency Capture
Range
fSYNC
250
3.0
–
–
500
–
kHz
V
P_6.1.5
P_6.1.6
1)
Synchronization
Signal
VSYNC,H
High Logic Level
Valid
1)
1)
Synchronization
Signal
Low Logic Level Valid
VSYNC,L
–
–
–
0.8
–
V
P_6.1.7
P_6.1.8
Synchronization
Signal
tSYNC,PWH
200
ns
Logic High Pulse
Width
1) Synchronization of external PWM ON signal to falling edge
Data Sheet
14
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Oscillator and Synchronisation
6.2
Typical Performance Characteristics of Oscillator
600
500
400
300
200
100
0
Tj = 25 °C
0
10 20 30 40 50 60 70 80
RFREQ/SYNC [kohm]
Oscillator _fFreq_vs_Rfreq.vsd
Figure 6-3 Switching Frequency fSW versus Frequency Select Resistor to GND RFREQ/SYNC
Data Sheet
15
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Enable and Dimming Function
7
Enable and Dimming Function
Description
The enable function powers on or off the device. A valid logic low signal on enable pin EN/PWMI powers off the
device and current consumption is less than 10 µA. A valid logic high enable signal on enable pin EN/PWMI
powers on the device. The enable function features an integrated pull down resistor which ensures that the IC
is shut down and the power switch is off in case the enable pin EN is left open.
In addition to the enable function described above, the EN/PWMI pin detects a pulse width modulated (PWM)
input signal that is fed through to an internal gate driver. The internal gate driver outputs the same PWM signal
on the PWMO pin to an external n-channel enhancement mode MOSFET for PWM dimming an LED load. PWM
dimming an LED is a commonly practiced dimming method to prevent color shift in an LED light source.
Moreover the PWM output function may also be used for to drive other types of loads besides LED.
The enable and PWM input function share the same pin. Therefore a valid logic low signal at the EN/PWMI pin
needs to differentiate between an enable power off signal or an PWM low signal. The device differentiates
between an enable off command and PWM dimming signal by requiring the signal at the EN/PWMI pin to stay
low for a minimum of 8 ms.
IN
14
Enable
Enable
PWMI
IVCC
1
2
5
LDO
EN / PWMI
SWO
Enable / PWMI
Logic
Gate
Driver
13
Microcontroller
PWMO
Gate
Driver
EN_PWMI_BlockDiagram.svg
Figure 7-1 Block Diagram and Simplified Application Circuit Enable and LED Dimming
Data Sheet
16
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Enable and Dimming Function
tEN,START
TPWMI
tPWMI,H
tEN,OFF,DEL
VEN/PWMI
VEN/PWMI,ON
VEN/PWMI,OFF
t
t
t
t
VIVCC
VIVCC,ON
VIVCC,RTH
VPWMO
1
fFREQ
TFREQ
=
VSWO
Power Off Delay Time
Power On
Power Off
Normal
SWO On
PWMO On
Dim
Normal
SWO On
PWMO On
Dim
Normal
SWO On
PWMO On
Iq < 10 μA
PWMO Off
SWO Off
PWMO Off
SWO Off
EN_PWMI_Timing.svg
Figure 7-2 Timing Diagram Enable and LED Dimming
7.1
Electrical Characteristics
VIN = 6 V to 40 V, Tj = -40°C to +150°C, all voltages with respect to ground (unless otherwise specified)
Table 7-1
Electrical Characteristics
Parameter
Symbol
Min.
Values
Typ.
Unit Note or
Test Condition
Number
Max.
Enable / PWM Input
Enable/PWMI
Turn On Threshold
VEN/PWMI,ON 3.0
VEN/PWMI,OFF
VEN/PWMI,HYS 50
IEN/PWMI,H
–
V
P_7.1.1
P_7.1.2
P_7.1.3
P_7.1.4
Enable/PWMI
Turn Off Threshold
–
–
0.8
400
30
V
Enable/PWMI
Hysteresis
200
–
mV
µA
Enable/PWMI
–
VEN/PWMI = 16.0 V
High Input Current
Data Sheet
17
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Enable and Dimming Function
Table 7-1
Electrical Characteristics
Parameter
Symbol
Values
Typ.
Unit Note or
Test Condition
Number
Min.
Max.
Enable/PWMI
Low Input Current
IEN/PWMI,L
tEN,OFF,DEL
–
0.1
1
µA
V
EN/PWMI = 0.5 V
P_7.1.5
P_7.1.6
Enable Turn Off
Delay Time
8
10
12
ms
PWMI Min Duty Time tPWMI,H
Enable Startup Time tEN,START
Gate Driver for Dimming Switch
4
–
–
–
–
µs
µs
P_7.1.7
P_7.1.8
100
PWMO Gate Driver
Peak Sourcing
Current1)
IPWMO,SR
C
–
230
–
mA
V
V
PWMO = 3.5V
PWMO = 1.5V
P_7.1.9
PWMO Gate Driver
Peak Sinking Current
IPWMO,SN
K
–
370
50
30
–
–
mA
ns
ns
V
P_7.1.10
P_7.1.11
P_7.1.12
P_7.1.13
PWMO Gate Driver
Output Rise Time
tR,PWMO
tF,PWMO
VPWMO
–
100
60
5.5
CL,PWMO = 3.3nF;
V
PWMO = 1V to 4V
PWMO Gate Driver
Output Fall Time
–
CL,PWMO = 3.3nF;
V
PWMO = 1V to 4V
PWMO Gate Driver
Output Voltage
4.5
CL,PWMO = 3.3nF
Current Consumption
Current
Consumption,
Shutdown Mode
Current
Consumption,
Active Mode2)
Iq_off
–
–
–
–
10
7
µA
V
EN/PWMI = 0.8 V;
P_7.1.14
P_7.1.15
Tj ≤ 105C; VIN = 16V
Iq_on
mA
VEN/PWMI ≥ 4.75 V;
IBO = 0 mA;
VIN = 16V
V
SWO = 0% Duty
1) Not subject to production test, specified by design
2) Dependency on switching frequency and gate charge of external switches.
Data Sheet
18
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Linear Regulator
8
Linear Regulator
Description
The internal linear voltage regulator supplies the internal gate drivers with a typical voltage of 5 V and current
up to ILIM,min (parameter 8.2.2). An external output capacitor with ESR lower than RIVCC,ESR (parameter
8.2.5) is required on pin IVCC for stability and buffering transient load currents. During normal operation the
external MOSFET switches will draw transient currents from the linear regulator and its output capacitor.
Proper sizing of the output capacitor must be considered to supply sufficient peak current to the gate of the
external MOSFET switches.
Integrated Undervoltage Protection for the External Switching MOSFET
An integrated undervoltage reset threshold circuit monitors the linear regulator output voltage (VIVCC) and resets
the device in case the output voltage falls below the IVCC undervoltage reset switch OFF threshold (VIVCC,RTH,d).
The undervoltage reset threshold for the IVCC pin helps to protect the external switches from excessive power
dissipation by ensuring the gate drive voltage is sufficient to enhance the gate of an external logic level n-channel
MOSFET.
IN
IVCC
14
1
Linear Regulator
EN / PWMI
13
Gate
Drivers
LinReg_BlckDiag.vsd
Figure 8-1 Voltage Regulator Block Diagram and Simplified Application Circuit
Data Sheet
19
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Linear Regulator
8.1
Electrical Characteristics
VIN = 6 V to 40 V; 4.5V ≤ VFBH ≤ 40V, 4.5V ≤ VFBL ≤ 40V, Tj = -40°C to +150°C, all voltages with respect to ground,
positive current flowing into pin; (unless otherwise specified)
Table 8-1
Electrical Characteristics
Parameter
Symbol
Min.
Values
Typ.
5
Unit Note or
Test Condition
Number
Max.
Output Voltage
VIVCC
4.6
5.4
V
6 V ≤ VIN ≤ 45 V
0.1 mA ≤ IIVCC ≤ 35
mA
P_8.1.1
Output Current
Limitation
ILIM
51
90
mA
VIN = 13.5 V
P_8.1.2
V
IVCC = 4.5V
Drop out Voltage
Output Capacitor
VDR
1.4
–
V
I
IVCC = 50mA 1)
P_8.1.3
P_8.1.4
P_8.1.5
2)
CIVCC
0.47
µF
W
Output Capacitor
ESR
RIVCC,ESR
0.5
f = 10kHz
Undervoltage Reset VIVCC,HDRM
Headroom
100
4.0
–
–
–
–
–
mV
V
V
V
IVCC decreasing
P_8.1.6
P_8.1.7
P_8.1.8
IVCC - VIVCC,RTH,d
Undervoltage Reset VIVCC,RTH,d
Threshold
–
V
IVCC decreasing
IVCC increasing
Undervoltage Reset VIVCC,RTH,i
4.5
V
V
Threshold
1) Measured when the output voltage VCC has dropped 100 mV from its nominal value.
2) Minimum value given is needed for regulator stability; application might need higher capacitance than the minimum.
Data Sheet
20
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Protection and Diagnostic Functions
9
Protection and Diagnostic Functions
9.1
Description
The TLD5095EL has integrated circuits to diagnose and protect against output overvoltage, open load, open
feedback and overtemperature faults. In case any of the four fault conditions occur the Status output ST will output
an active logic low signal to communicate that a fault has occurred. During an overvoltage or open load condition
the gate driver outputs SWO and PWMO will turn off. Figure 9-3 illustrates the various open load and open
feedback conditions. In the event of an overtemperature condition (Figure 9-6) the integrated thermal shutdown
function turns off the gate drivers and internal linear voltage regulator. The typical junction shutdown temperature
is 175°C. After cooling down the IC will automatically restart operation. Thermal shutdown is an integrated
protection function designed to prevent immediate IC destruction and is not intended for continuous use in normal
operation.
Input
Output
Protection and
Diagnostic Circuit
Output
Overvoltage
Open Load
SWO and PWMO
Gate Driver Off
OR
Open Feedback
Overtemperature
Linear Regualtor
Off
OR
Input
Undervoltage
Pro_Diag_BlckDiag.vsd
Figure 9-1 Protection and Diagnostic Function Block Diagram
Input
Output
Condition
Level*
False
True
ST
H
L
SWO
Sw*
L
PWMO
H or Sw*
IVCC
Active
Active
Overvoltage
L
False
True
H
L
Sw*
L
H or Sw*
Active
Active
Open Load
L
False
True
False
True
H
L
H
L
Sw*
L
Sw*
L
H or Sw*
Active
Active
Active
Shutdown
Pro_Diag_TT.vsd
Open Feedback
Overtemperature
L
H or Sw*
L
*Note:
Sw = Switching
False = Condition does not exist
True = Condition does exist
Figure 9-2 Status Output Truth Table
Data Sheet
21
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Protection and Diagnostic Functions
VBO
Output Open Circuit Conditions
Open Circuit 3
Open Circuit 1
Open Circuit
Fault Condition
Condition
Fault Threshold Voltage
VREF
TLD5095
1
2
3
4
Open FBH
Open FBL
-20 to -100 mV
0.5 to 1.0 V
ROVH
RFB
Overvoltage
Compartor
OVFB
Open Circuit 2
D1
9
Open VBO
Open PWMO
VFBx < VFBx,min = 4.5V
Detected by overvoltage
ROVL
VOVFB,TH
D2
D3
D4
D5
D6
D7
D8
D9
D10
VREF
Feedback Voltage
Error Amplifier
FBH
6
+
VREF
-
FBL
Max Threshold = 1.0 V
7
Min Threshold = 0.5 V
Typical VREF = 0.3 V
Open Circuit 4
TDIM
Max Threshold = -20 mV
Min Threshold = -100 mV
PWMO
5
Figure 9-3 Open Load and Open Feedback Conditions
VOVFB
example: VOUT,max=40V
VOVP,max
1.25mA
Overvoltage Protection
40V
ROVH
ACTIVE
≅ 33.2kΩ
TLD5095
1.25mA
9
VOVFB,TH
OVFB
1.25V
ROVL
1kΩ
1.25V
Overvoltage Protection is
disabled
GND
12
t
Figure 9-4 Overvoltage Protection Description
Data Sheet
22
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Protection and Diagnostic Functions
Status Output Timing Diagram
Startup
Normal
Thermal
Shutdown
Overvoltage
2
Open Load /
Feedback
Shutdown
1
3
VIVCC
VIVCC,RTH,i
VIVCC,RTH,d
t
t
t
t
TJ,SD,HYST
1
TJ
TJ,SD
2
VBO
VOVFB ≥ VOVFB,TH
VOVFB < VOVFB,T L
3
VFBH-VFBL
VREF,2
tSS
tSS
0.3 V Typ
VREF,1
tSD
tSD
tSD
VST
t
Figure 9-5 Status Output Timing Diagram
Data Sheet
23
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Protection and Diagnostic Functions
VEN/PWMI
H
L
t
Tj
T
jSD
ΔΤ
TjSO
t
Ta
VSWO
t
ILED
Ipeak
t
VPWMO
t
VST and
VIVCC
5V
t
Device
OFF
Overtemp
Fault
Overtemp
Fault
Overtemp Overtemp
ON
Fault Fault
Normal Operation
ON
ON
Figure 9-6 Device Overtemperature Protection Behavior
Data Sheet 24
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Protection and Diagnostic Functions
9.2
Electrical Characteristics
VIN = 6 V to 40 V; 4.5V ≤ VFBH ≤ 40V, 4.5V ≤ VFBL ≤ 40V, Tj = -40°C to +150°C, all voltages with respect to ground,
positive current flowing into pin; (unless otherwise specified)
Table 9-1
Electrical Characteristics
Parameter
Symbol
Min.
Values
Typ.
Unit Note or
Test Condition
Number
Max.
Status Output
Status Output
Voltage Low
VST,LOW
–
2
–
8
–
0.4
–
V
I
ST = 1mA
P_9.2.1
P_9.2.2
P_9.2.3
P_9.2.4
Status Sink Current IST,MAX
Limit
–
mA
µA
ms
VST = 1V
Status Output
Current
IST,HIGH
–
1
VST = 5V
Status Delay Time
tSD
10
12
Temperature Protection
Overtemperature
Shutdown
Tj,SD
160
–
175
15
190
–
°C
°C
P_9.2.5
P_9.2.6
Overtemperature
Shutdown
Tj,SD,HYST
Hystereses
Overvoltage Protection
Output Over Voltage VOVFB,TH
Feedback Threshold
Increasing
1.21
1.25
1.29
V
P_9.2.7
Output Voltage
decreasing
Output Over Voltage VOVFB,HYS
Feedback Hysteresis
50
2
–
150
10
1
mV
µs
P_9.2.8
P_9.2.9
P_9.2.10
Over Voltage
Reaction Time
tOVPRR
IOVFB
–
Output Voltage
decreasing
Over Voltage
Feedback Input
Current
-1
0.1
µA
VOVFB = 1.25 V
Open Load and Open Feedback Diagnostics
OpenLoad/Feedback VREF,1,3
Threshold
-100
–
–
-20
1
mV
V
VREF = VFBH - VFBL
Open Circuit 1 or 3
P_9.2.11
P_9.2.12
Open Feedback
Threshold
VREF,2
0.5
VREF = VFBH - VFBL
Open Circuit 2
Note: Integrated protection functions are designed to prevent IC destruction under fault conditions described in
the data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions
are not designed for continuous repetitive operation.
Data Sheet
25
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Application Information
10
Application Information
Note: The following information is given as a hint for the implementation of the device only and shall not be
regarded as a description or warranty of a certain functionality, condition or quality of the device.
LBO
DBO
VIN = 4.75V to 45V
CIN
CBO
RFB
VREF
TSW
2
4
SWO
14
1
IN
SWCS
D1
IVCC
VCC or VIVCC
CIVCC
RCS
D2
D3
D4
D5
D6
D7
D8
D9
D10
3
9
SGND
OVFB
ROVH
RST
10
STATUS
ST
ROVL
IC1
TLD5095
IC2
Microcontroller
(e.g. XC866)
PWMI
13
11
8
EN / PWMI
FREQ / SYNC
COMP
Digital Dimming
6
7
FBH
FBL
Spread
Spectrum
ILED
CCOMP
PWMO
TDIM
5
PWMO
GND
RFREQ
RCOMP
12
Figure 10-1 Boost to Ground Application Circuit - B2G (Boost configuration)
Reference
Designator
Part
Number
Value
Manufacturer
Type
Quantity
D1 - 10
DBO
White
Schottky, 3 A, 100 VR
100 uF, 50V
10 nF
Osram
Vishay
LUW H9GP
SS3H10
LED
Diode
10
1
2
1
1
1
1
1
1
1
2
1
1
1
1
2
2
CIN, CBO
CCOMP
CIVCC
IC1
Panasonic
EPCOS
EEEFK1H101GP
X7R
Capacitor
Capacitor
Capacitor
IC
MLCC CCNPZC105KBW X7R
TLD5095
1uF , 6.3V
EPCOS
--
Infineon
IC2
--
Infineon
XC866
IC
LBO
100 uH
Coilcraft
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Infineon
MSS1278T-104ML
ERJ3EKF1002V
ERJ14BQFR82U
ERJ3EKF2002V
ERJ3EKF3322V
ERJ3EKF1001V
ERJB1CFR05U
IPG20N06S4L-26
IPG20N10S4L-22
BSP318S
Inductor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Transistor
Transistor
Transistor
RCOMP
RFB
10 kΩ, 1%
820 mΩ, 1%
20 kΩ, 1%
RFREQ, RST
ROVH
33.2 kΩ, 1%
1 kΩ, 1%
ROVL
RCS
50 mΩ, 1%
Dual N-ch enh. (60V, 20A)
alternativ: 100V N-ch, 35A
alternativ: 60V N-ch, 2.6A
TDIM,TSW
Infineon
Infineon
Figure 10-2 Bill of Materials for B2G Application Circuit
Data Sheet 27
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Application Information
L1
DBO
CSEPIC
VIN
VIN = 4.75V to 45V
CIN
ISW
RFB
L2
VREF
CBO
TSW
2
4
SWO
14
IN
SWCS
ILED
VCC or VIVCC
RCS
D1
ROVH
3
9
SGND
OVFB
D2
D3
D4
D5
D6
D7
RST
10
STATUS
ST
ROVL
IC1
IC2
Microcontroller
TLD5095
EN / PWMI
FREQ/ SYNC
COMP
(e.g. XC866)
PWMI
13
11
8
Digital Dimming
Spread Spectrum
6
7
FBH
FBL
CCOMP
Dn
DPOL
RPOL
1
IVCC
CIVCC
PWMO
RFREQ
RCOMP
TDIM
5
PWMO
GND
12
Figure 10-3 SEPIC Application Circuit (Buck-Boost configuration)
Reference
Designator
Part
Number
Value
Manufacturer
Type
Quantity
D1 - n
DBO
White
Schottky, 3 A, 100 VR
80V Diode
Osram
Vishay
LUW H9GP
SS3H10
LED
Diode
Diode
variable
1
1
1
DPOL
CSEPIC
Infineon
EPCOS
BAS1603W
X7R, Low ESR
3.3 uF, 20V
Capacitor
Capacitor
Capacitor
Capacitor
IC
CIN, CBO
CCOMP
CIVCC
IC1
100 uF, 50V
Panasonic
EPCOS
EPCOS
Infineon
Infineon
Coilcraft
EEEFK1H101GP
X7R
2
1
1
1
1
2
10 nF
1uF , 6.3V
--
X7R
TLD5095
IC2
--
XC866
IC
L1 , L2
47 uH
MSS1278T-473ML
Inductor
alternativ: 22uH coupled
inductor
Coilcraft
MSD1278-223MLD
Inductor
1
RCOMP, RPOL
RFB
RFREQ, RST
ROVH
10 kΩ, 1%
820 mΩ, 1%
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Infineon
ERJ3EKF1002V
ERJ14BQFR82U
ERJ3EKF2002V
ERJ3EKF3322V
ERJ3EKF1001V
ERJB1CFR05U
IPG20N06S4L-26
IPD35N10S3L-26
BSP318S
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Transistor
Transistor
Transistor
2
1
2
1
1
1
1
2
2
20 kΩ, 1%
33.2 kΩ, 1%
ROVL
1 kΩ, 1%
RCS
50 mΩ, 1%
Dual N-ch enh. (60V, 20A)
alternativ: 100V N-ch, 35A
alternativ: 60V N-ch, 2.6A
TDIM,TSW
Infineon
Infineon
Figure 10-4 Bill of Materials for SEPIC Application Circuit
Data Sheet 28
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Application Information
DBO
VIN
VIN = 4.75V to 45V
CIN
L1
ISW
RFB
L2
VREF
CBO
TSW
2
4
SWO
14
IN
SWCS
ILED
VCC or VIVCC
RCS
ROVH
D1
3
9
SGND
OVFB
D2
D3
D4
D5
D6
D7
RST
10
STATUS
ST
ROVL
IC1
IC2
Microcontroller
TLD5095
EN / PWMI
FREQ/ SYNC
COMP
(e.g. XC866)
PWMI
13
11
8
Digital Dimming
Output
6
7
FBH
FBL
CCOMP
DPOL
RPOL
Dn
1
IVCC
CIVCC
RFREQ
RCOMP
TDIM
5
PWMO
GND
PWMO
12
Figure 10-5 Flyback Application Circuit (Buck-Boost configuration)
Reference
Designator
Part
Number
Value
Manufacturer
Type
Quantity
D1 - n
DBO
CBO
CIN
White
Schottky, 3 A, 100 VR
3.3 uF, 50V (100V)
100 uF, 50V
47 nF
Osram
Vishay
LUW H9GP
SS3H10
LED
Diode
variable
1
1
1
1
1
1
1
EPCOS
Panasonic
EPCOS
EPCOS
Infineon
Infineon
X7R, Low ESR
Capacitor
Capacitor
Capacitor
Capacitor
IC
EEEFK1H101GP
X7R
CCOMP
CIVCC
IC1
1 uF , 6.3V
--
X7R
TLD5095
XC866
IC2
--
IC
L1 , L2
1 µH / 9 uH
EPCOS
Transformer EHP 16
ERJ3EKF1002V
Inductor
Resistor
1
2
RCOMP, RPOL
10 kΩ, 1%
Panasonic
DPOL
RFB
80 V Diode
820 mΩ, 1%
Infineon
Isabellenhütte
Panasonic
Panasonic
Panasonic
Isabellenhütte
Infineon
BAS1603W
SMS – Power Resistor
ERJ3EKF1002V
ERJ3EKF5622V
ERJ3EKF1241V
SMS - Power Resistor
IPG20N06S4L-26
IPG20N10S4L-22
BSP318S
Diode
1
1
2
1
1
1
1
2
2
Resistor
Resistor
Resistor
Resistor
Resistor
RFREQ, RST
ROVH
10 kΩ, 1%
56.2 kΩ, 1%
ROVL
1.24 kΩ, 1%
RCS
5 mΩ, 1%
Dual N-ch enh. (60V, 20A)
alternativ: 100V N-ch, 35A
alternativ: 60V N-ch, 2.6A
TDIM,TSW
Transistor
Transistor
Transistor
Infineon
Infineon
Figure 10-6 Bill of Materials for Flyback Application Circuit
Data Sheet 29
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Application Information
CBO
RFB
TDIM2
VIN = 4.75V to 45V
CIN
DZ
Dn
D1
RDIM2
Number of LEDs could be
variable independent from VIN:
Æ BUCK-BOOST configuration
RDIM1
ILED
LBO
DBO
TDIM1
ISW
PWMO
VOUT
TSW
5
PWMO
2
4
SWO
SWCS
VCC or VIVCC
6
FBH
RCS
7
FBL
IN
3
9
SGND
OVFB
ROVH
RST
14
10
STATUS
ST
IC2
ROVL
IC1
Microcontroller
(e.g. XC866)
TLD5095
PWMI
13
11
Digital Dimming
Spread Spectrum
EN / PWMI
FREQ / SYNC
8
COMP
IVCC
CCOMP
1
CIVCC
GND
12
RFREQ
RCOMP
Figure 10-7 Boost to Battery Application Circuit - B2B (Buck-Boost configuration)
Reference
Designator
Part
Number
Value
Manufacturer
Type
Quantity
D1 - n
DBO
DZ
White
Schottky, 3 A, 100 VR
5V
Osram
Vishay
Vishay
LUW H9GP
SS3H10
Zener
Diode
Diode
Diode
variable
1
1
CBO
CIN
100 uF, 80V
100 uF, 50V
Panasonic
Panasonic
EEVFK1K101Q
Capacitor
Capacitor
1
1
EEEFK1H101GP
CCOMP
CIVCC
IC1
10 nF
1 uF, 6.3V
--
EPCOS
EPCOS
Infineon
Infineon
Coilcraft
X7R
MLCC CCNPZC105KBW X7R
TLD5095
Capacitor
Capacitor
IC
1
1
1
1
1
IC2
--
XC866
IC
LBO
100 uH
MSS1278T-104ML_
Inductor
RCOMP, RDIM1, RDIM2
RFB
RFREQ, RST
ROVH
10 kΩ, 1%
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Infineon
ERJ3EKF1002V
ERJ14BQFR82U
ERJ3EKF2002V
ERJP06F5102V
ERJ3EKF1001V
ERJB1CFR05U
BSO615CG
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Transistor
Transistor
Transistor
3
1
2
1
1
1
1
1
1
820 mΩ, 1%
20 kΩ, 1%
33.2 kΩ, 1%
ROVL
1 kΩ, 1%
RCS
50 mΩ, 1%
TDIM1,TDIM2
60V Dual N-ch (3.1A) and P-ch. enh. (2A)
alternativ: 100V N-ch (0.37A),
alternativ: 60V P-ch (1.9A)
Infineon
BSP123
Infineon
BSP171P
N-ch, OptiMOS-T2 100V, 35A
alternativ: 60V N-ch, 30A
TSW
Infineon
Infineon
Infineon
IPD35N10S3L-26
IPD30N06S4L-23
BSP318S
Transistor
1
Transistor
Transistor
1
1
alternativ: 60V N-ch, 2.6A
Figure 10-8 Bill of Materials for B2B Application Circuit
Data Sheet 30
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Application Information
DBO
CBO
D2
D1
VREF
LBO
VIN = 4.75V to 45V
CIN
ILED
RFB
BUCK Setup:
VIN > VOUT
TSW
2
4
SWO
14
1
IN
CIVCC
SWCS
IVCC
VCC or VIVCC
RCS
3
9
SGND
OVFB
RST
10
STATUS
ST
IC1
IC2
Microcontroller
TLD5095
EN / PWMI
FREQ / SYNC
COMP
(e.g. XC866)
13
11
8
Enable
6
7
FBH
FBL
Spread Spectrum
CCOMP
5
PWMO
GND
RFREQ
RCOMP
12
Figure 10-9 Buck Application Circuit
Reference
Value
Part
Number
Manufacturer
Type
Quantity
Designator
D1 -2
DBO
White
Schottky, 3 A, 100 VR
4.7 uF, 50V
100 uF, 50V
47 nF
Osram
Vishay
LE UW Q9WP
SS3H10
LED
2
1
1
1
1
1
1
1
Diode
CBO
EPCOS
Panasonic
EPCOS
EPCOS
Infineon
Infineon
X7R
Capacitor
Capacitor
Capacitor
Capacitor
IC
CIN
EEEFK1H101GP
X7R
CCOMP
CIVCC
IC1
MLCC CCNPZC105KBW X7R
TLD5095
1 uF , 6.3V
--
IC2
--
XC866
IC
L1
22 µH
Coilcraft
Panasonic
Isabellenhütte
MSS1278T
Inductor
Resistor
1
1
RCOMP
10 kΩ, 1%
ERJ3EKF1002V
RFB
RFREQ, RST
RCS
820 mΩ, 1%
20 kΩ, 1%
SMS – Power Resistor
ERJ3EKF2002V
Resistor
Resistor
1
2
1
1
1
Panasonic
Isabellenhütte
Infineon
50 mΩ, 1%
SMS - Power Resistor
IPG20N10S4L-22
IPD30N06S4L-23
Resistor
100V, N-ch, 35A
TSW
Transistor
Transistor
alternativ: 60V N-ch, 30A
Infineon
Figure 10-10 Bill of Materials for Buck Application Circuit
Data Sheet 31
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Application Information
LBO
DBO
ILoad
VIN = 4.75V to 45V
CIN
CBO
constant
VOUT
RL
2
4
TSW
SWO
14
1
IN
SWCS
IVCC
VCC or VIVCC
CIVCC
RCS
3
9
ROVH
SGND
OVFB
RST
10
5
STATUS
ST
ROVL
IC1
IC2
Microcontroller
(e.g. XC866)
PWMO TLD5095
EN / PWMI
FREQ / SYNC
COMP
RFB1
13
11
8
Enable
6
7
FBH
FBL
Spread Spectrum
RFB2
VREF
CCOMP
RFB3
GND
12
RFREQ
RCOMP
Figure 10-11 Boost Voltage Application Circuit
Reference
Designator
Part
Number
Value
Manufacturer
Type
Quantity
1
DBO
Schottky, 3 A, 100 VR
Vishay
SS3H10
Diode
CBO
CIN
100 uF, 80V
100 uF, 50V
Panasonic
Panasonic
EEVFK1K101Q
Capacitor
Capacitor
1
1
EEEFK1H101GP
X7R
CCOMP
CIVCC
IC1
10 nF, 16V
1 uF, 6.3V
EPCOS
Panasonic
Infineon
Capacitor
Capacitor
IC
1
1
1
1
1
1
1
1
2
1
1
1
1
X7R
--
TLD5095
XC866
IC2
--
Infineon
IC
LBO
100 uH
Coilcraft
MSS1278T-104ML_
ERJ3EKF1002V
ERJ3EKF5102V
ERJ3EKF1001V
ERJ3EKF2002V
ERJ3EKF3322V
ERJ3EKF1001V
ERJB1CFR05U
IPD35N10S3L-26
Inductor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Resistor
Transistor
RCOMP
RFB1,RFB3
RFB2
10 kohms, 1%
51 kohms, 1%
1 kohms, 1%
20 kohms, 1%
33.2 kohms, 1%
1 kohms, 1%
50 mohms, 1%
N-ch, OptiMOS-T2 100V
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
Infineon
RFREQ, RST
ROVH
ROVL
RCS
TSW
Figure 10-12 Bill of Materials for Boost Voltage Application Circuit
Note: The application drawings and corresponding bill of materials are simplified examples. Optimization of the
external components must be done accordingly to specific application requirements.
Data Sheet
32
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Application Information
10.1
Further Application Information
•
•
For further information you may contact http://www.infineon.com/
Application Note: TLD509x DC-DC Multitopology Controller IC “Dimensioning and Stability Guideline -
Theory and Practice”
Data Sheet
33
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Package Outlines
11
Package Outlines
0.35 x 45˚
1)
0.1 C D
0.1
3.9
+0.06
0.19
0.08
C
C
0.64
0.25
0.65
2)
0.05
0.2
0.25
6
M
M
0.2
D 8x
0.15
C A-B D 14x
D
Bottom View
0.2
3
A
1
7
14
8
1
7
14
8
Exposed
Diepad
B
0.1 C A-B 2x
1)
0.1
4.9
Index Marking
1) Does not include plastic or metal protrusion of 0.15 max. per side
2) Does not include dambar protrusion
PG-SSOP-14-1,-2,-3-PO V02
Figure 11-1 Outline PG-SSOP-14 Dimensions in mm
Green Product (RoHS Compliant)
To meet the world-wide customer requirements for environmentally friendly products and to be compliant
with government regulations the device is available as a green product. Green products are RoHS-Compliant
(i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).
Note: For further package information, please visit our website: http://www.infineon.com/packages.
Data Sheet
34
Revision1.4
2015-03-11
Infineon® LITIX™ Power
TLD5095EL
Revision History
Revision 1.4, 2015-03-11
Page or Item Subjects (major changes since previous revision)
Responsible Date
2009-11-30 to
Rev1.0 to Rev Initial Data Sheet for TLD5095EL
1.4
2014-03-10
Data Sheet
35
Revision 1.4 2015-03-11
Trademarks of Infineon Technologies AG
AURIX™, C166™, CanPAK™, CIPOS™, CoolGaN™, CoolMOS™, CoolSET™, CoolSiC™, CORECONTROL™, CROSSAVE™, DAVE™, DI-POL™, DrBLADE™, EasyPIM™,
EconoBRIDGE™, EconoDUAL™, EconoPACK™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™, HITFET™, HybridPACK™, Infineon™, ISOFACE™, IsoPACK™, i-
Wafer™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OmniTune™, OPTIGA™, OptiMOS™, ORIGA™, POWERCODE™, PRIMARION™, PrimePACK™,
PrimeSTACK™, PROFET™, PRO-SIL™, RASIC™, REAL3™, ReverSave™, SatRIC™, SIEGET™, SIPMOS™, SmartLEWIS™, SOLID FLASH™, SPOC™, TEMPFET™,
thinQ!™, TRENCHSTOP™, TriCore™.
Other Trademarks
Advance Design System™ (ADS) of Agilent Technologies, AMBA™, ARM™, MULTI-ICE™, KEIL™, PRIMECELL™, REALVIEW™, THUMB™, µVision™ of ARM Limited,
UK. ANSI™ of American National Standards Institute. AUTOSAR™ of AUTOSAR development partnership. Bluetooth™ of Bluetooth SIG Inc. CAT-iq™ of DECT
Forum. CIPURSE™ of OSPT Alliance. COLOSSUS™, FirstGPS™ of Trimble Navigation Ltd. EMV™ of EMVCo, LLC (Visa Holdings Inc.). EPCOS™ of Epcos AG.
FLEXGO™ of Microsoft Corporation. HYPERTERMINAL™ of Hilgraeve Incorporated. MCS™ of Intel Corp. IEC™ of Commission Electrotechnique Internationale.
IrDA™ of Infrared Data Association Corporation. ISO™ of INTERNATIONAL ORGANIZATION FOR STANDARDIZATION. MATLAB™ of MathWorks, Inc. MAXIM™ of
Maxim Integrated Products, Inc. MICROTEC™, NUCLEUS™ of Mentor Graphics Corporation. MIPI™ of MIPI Alliance, Inc. MIPS™ of MIPS Technologies, Inc.,
USA. muRata™ of MURATA MANUFACTURING CO., MICROWAVE OFFICE™ (MWO) of Applied Wave Research Inc., OmniVision™ of OmniVision Technologies,
Inc. Openwave™ of Openwave Systems Inc. RED HAT™ of Red Hat, Inc. RFMD™ of RF Micro Devices, Inc. SIRIUS™ of Sirius Satellite Radio Inc. SOLARIS™ of
Sun Microsystems, Inc. SPANSION™ of Spansion LLC Ltd. Symbian™ of Symbian Software Limited. TAIYO YUDEN™ of Taiyo Yuden Co. TEAKLITE™ of CEVA,
Inc. TEKTRONIX™ of Tektronix Inc. TOKO™ of TOKO KABUSHIKI KAISHA TA. UNIX™ of X/Open Company Limited. VERILOG™, PALLADIUM™ of Cadence Design
Systems, Inc. VLYNQ™ of Texas Instruments Incorporated. VXWORKS™, WIND RIVER™ of WIND RIVER SYSTEMS, INC. ZETEX™ of Diodes Zetex Limited.
Trademarks Update 2014-11-12
www.infineon.com
Edition 2015-03-11
Published by
Infineon Technologies AG
81726 Munich, Germany
Legal Disclaimer
The information given in this document shall in
no event be regarded as
Warnings
Due to technical requirements, components
may contain dangerous substances. For
information on the types in question, please
contact the nearest Infineon Technologies
Office. Infineon Technologies components may
be used in life-support devices or systems only
with the express written approval of Infineon
Technologies, if a failure of such components
can reasonably be expected to cause the failure
of that life-support device or system or to affect
the safety or effectiveness of that device or
system. Life support devices or systems are
intended to be implanted in the human body or
to support and/or maintain and sustain and/or
protect human life. If they fail, it is reasonable to
assume that the health of the user or other
persons may be endangered.
a guarantee of
conditions or characteristics. With respect to any
examples or hints given herein, any typical
values stated herein and/or any information
regarding the application of the device, Infineon
Technologies hereby disclaims any and all
warranties and liabilities of any kind, including
without limitation, warranties of non-
infringement of intellectual property rights of
any third party.
© 2014 Infineon Technologies AG.
All Rights Reserved.
Do you have a question about any
aspect of this document?
Email: erratum@infineon.com
Information
For further information on technology, delivery
terms and conditions and prices, please contact
the nearest Infineon Technologies Office
(www.infineon.com).
Document reference
Doc_Number
相关型号:
TLD5191ES
TLD5191ES 是一款具有内置保护功能的同步 MOSFET H 桥 DC-DC 控制器。 该设计有利于以最高的系统效率和最少的外部组件驱动高功率 LED。 TLD5191ES 具有模拟和数字 (PWM) 调光及嵌入式 PWM 发生器。 开关频率可在 200 kHz 至 700 kHz 范围内调节。 内置扩频开关频率调制和强制连续电流调节模式改善了整体 EMC 行为。 此外,电流模式调节方案提供了一个由小型外部补偿元件维持的稳定调节环路。 可调软启动功能可限制启动时的电流峰值和电压过冲。 TLD5191ES 适用于汽车环境以及工业和消费类应用(例如无线充电)。
INFINEON
©2020 ICPDF网 联系我们和版权申明