V23818-M305-B57 [INFINEON]
SFP - Small Form-factor Pluggable Multimode 850 nm 2.125 and 1.0625 Gbit/s Fibre Channel 1.25 Gigabit Ethernet Transceiver with LC⑩ Connector; SFP - 小型可插拔多模850纳米2.125和1.0625 Gbit / s的光纤通道1.25千兆以太网收发器LC⑩连接器
| 型号： | V23818-M305-B57 |
| 厂家： | 
Infineon |
| 描述： | SFP - Small Form-factor Pluggable Multimode 850 nm 2.125 and 1.0625 Gbit/s Fibre Channel 1.25 Gigabit Ethernet Transceiver with LC⑩ Connector |
| 文件： | 总19页 (文件大小：1344K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Fiber Optics
SFP - Small Form-factor Pluggable
V23818-M305-B57
Multimode 850 nm 2.125 and 1.0625 Gbit/s Fibre Channel
1.25 Gigabit Ethernet Transceiver with LC™ Connector
Features
• Small Form-factor Pluggable (SFP) transceiver
• Fully SFP MSA compliant1)
• Advanced release mechanism
– Easy access, even in belly to belly applications
– Grip for easy access – no tool is needed
– Color coded black (multimode)
• Excellent EMI performance
File: 1114
• RJ-45 style LC™ connector system
• Single power supply (3.3 V)
• Extremely low power consumption of 415 mW typical
• Small size for high channel density
• UL-94 V-0 certified
• ESD Class 1C per JESD22-A114-B (MIL-STD 883D Method 3015.7)
• Compliant with FCC (Class B) and EN 55022
• For distances of up to 700 m (50 µm fiber)
• Class 1 FDA and IEC laser safety compliant
• AC/AC Coupling according to SFP MSA
• Recommendation: Infineon Cage one-piece design V23838-S5-N1 for press fit and/or
solderable
• Operating case temperature: –10°C to 85°C
• SFP evaluation board V23818-S5-V2 available upon request
1)
Current MSA documentation can be found at www.infineon.com/fiberoptics
LC™ is a trademark of Lucent
Data Sheet
1
2003-04-25
V23818-M305-B57
Pin Configuration
Pin Configuration
1
2
3
4
5
6
7
8
9
10
V
T
20
19
18
17
16
15
14
13
12
11
V
T
EE
EE
Tx Fault
TD−
TD+
Tx Disable
MOD-DEF(2)
MOD-DEF(1)
V
V
T
T
EE
CC
CC
MOD-DEF(0)
Rate Select
V
V
R
R
EE
LOS
RD+
V
V
R
R
RD−
EE
V
R
EE
EE
Bottom of transceiver (as viewed
through top of transceiver)
Top of transceiver
File: 1306
Figure 1
SFP Transceiver Electrical Pad Layout
Data Sheet
2
2003-04-25
V23818-M305-B57
Pin Configuration
Pin Description
Pin No. Name
Logic Level
N/A
Function
1
VEET
Transmitter Ground1)
Transmitter Fault Indication2) 8)
Transmitter Disable3)
Module Definition 24) 8)
Module Definition 15) 8)
Module Definition 06) 8)
Not connected
2
Tx Fault
Tx Disable
MOD-DEF(2)
MOD-DEF(1)
MOD-DEF(0)
Rate Select
LOS
LVTTL
LVTTL
LVTTL
LVTTL
N/A
3
4
5
6
7
N/A
8
LVTTL
N/A
Loss Of Signal7) 8)
Receiver Ground1)
9
VEER
10
11
12
13
14
15
16
17
18
19
20
VEER
N/A
Receiver Ground1)
Receiver Ground1)
Inv. Received Data Out9)
Received Data Out9)
Receiver Ground1)
VEER
N/A
RD–
LVPECL
LVPECL
N/A
RD+
VEER
VCCR
N/A
Receiver Power
VCCT
N/A
Transmitter Power
Transmitter Ground1)
Transmit Data In10)
Inv. Transmit Data In10)
Transmitter Ground1)
VEET
N/A
TD+
LVPECL
LVPECL
N/A
TD–
VEET
1)
2)
3)
4)
5)
6)
7)
Common transmitter and receiver ground within the module.
A high signal indicates a laser fault of some kind and that laser is switched off.
A low signal switches the transmitter on. A high signal or when not connected switches the transmitter off.
MOD-DEF(2) is the data line of two wire serial interface for serial ID.
MOD-DEF(1) is the clock line of two wire serial interface for serial ID.
MOD-DEF(0) is grounded by the module to indicate that the module is present.
A low signal indicates normal operation, light is present at receiver input. A high signal indicates the received
optical power is below the worst case receiver sensitivity.
Should be pulled up on host board to VCC by 4.7 - 10 kW.
AC coupled inside the transceiver. Must be terminated with 100 W differential at the user SERDES.
AC coupled and 100 W differential termination inside the transceiver.
8)
9)
10)
Data Sheet
3
2003-04-25
V23818-M305-B57
Description
Description
The Infineon Fibre Channel / Gigabit Ethernet multimode transceiver – part of Infineon
Small Form Factor transceiver family – is based on the Physical Medium Depend (PMD)
sublayer and baseband medium, type 1000 Base-SX (short wavelength) as specified in
IEEE Std 802.3, Fibre Channel
FC-PI (Rev. 13) 200-M5-SN-I, 200-M6-SN-I,
FC-PI (Rev. 13) 100-M5-SN-I, 100-M6-SN-I.
The appropriate fiber optic cable is 62.5 µm or 50 µm multimode fiber with LC™
connector.
Link Length as Defined by IEEE and Fibre Channel Standards
Fiber Type
Reach
max.2)
Unit
min.1)
at 1.0625 Gbit/s
50 µm, 2000 MHz*km
50 µm, 500 MHz*km
50 µm, 400 MHz*km
62.5 µm, 200 MHz*km
62.5 µm, 160 MHz*km
at 1.25 Gbit/s
0.5
0.5
0.5
0.5
0.5
860
500
450
300
250
meters
50 µm, 500 MHz*km
50 µm, 400 MHz*km
62.5 µm, 200 MHz*km
62.5 µm, 160 MHz*km
at 2.125 Gbit/s
2
2
2
2
550
500
275
220
meters
meters
50 µm, 2000 MHz*km
50 µm, 500 MHz*km
50 µm, 400 MHz*km
62.5 µm, 200 MHz*km
0.5
0.5
0.5
0.5
0.5
500
300
260
150
120
62.5 µm, 160 MHz*km
1)
Minimum reach as defined by IEEE and Fibre Channel Standards. A 0 m link length (loop-back connector) is
supported.
2)
Maximum reach as defined by IEEE and Fibre Channel Standards. Longer reach possible depending upon link
implementation.
Data Sheet
4
2003-04-25
V23818-M305-B57
Description
The Infineon SFP multimode transceiver is a single unit comprised of a transmitter, a
receiver, and an LC™ receptacle.
This transceiver supports the LC™ connectorization concept. It is compatible with RJ-45
style backpanels for high end datacom and telecom applications while providing the
advantages of fiber optic technology.
The module is designed for low cost SAN, LAN, WAN, Fibre Channel applications. It can
be used as the network end device interface in mainframes, workstations, servers, and
storage devices, and in a broad range of network devices such as bridges, routers, hubs,
and local and wide area switches.
This transceiver operates at 1.0625/1.25/2.125 Gbit/s from a single power supply
(+3.3 V). The full differential data inputs and outputs are LVPECL compatible.
Functional Description of SFP Transceiver
This transceiver is designed to transmit serial data via multimode cable.
Tx Fault
Automatic
Shut-Down
TxDis
LEN
Tx Coupling Unit
TD−
Laser
Driver
e/o
Laser
TD+
Power
Control
o/e
Multimode Fiber
Monitor
Rx Coupling Unit
o/e
RD−
RD+
Receiver
EPROM
LOS
MOD-DEF
File: 1355
Figure 2
Functional Diagram
Data Sheet
5
2003-04-25
V23818-M305-B57
Description
The receiver component converts the optical serial data into LVPECL compatible
electrical data (RD+ and RD–). The Loss Of Signal (LOS) shows whether an optical
signal is present.
The transmitter converts LVPECL compatible electrical serial data (TD+ and TD–) into
optical serial data. Data lines are differentially 100 W terminated.
The transmitter contains a laser driver circuit that drives the modulation and bias current
of the laser diode. The currents are controlled by a power control circuit to guarantee
constant output power of the laser over temperature and aging. The power control uses
the output of the monitor PIN diode (mechanically built into the laser coupling unit) as a
controlling signal, to prevent the laser power from exceeding the operating limits.
Single fault condition is ensured by means of an integrated automatic shutdown circuit
that disables the laser when it detects laser fault to guarantee the laser Eye Safety.
The transceiver contains a supervisory circuit to control the power supply. This circuit
makes an internal reset signal whenever the supply voltage drops below the reset
threshold. It keeps the reset signal active for at least 140 milliseconds after the voltage
has risen above the reset threshold. During this time the laser is inactive.
A low signal on TxDis enables transmitter. If TxDis is high or not connected the
transmitter is disabled.
The information which kind of SFP module has been plugged into an SFP port can be
read through the MOD-DEF interface. The information is stored in an I2C-Eprom inside
the SFP Transceiver.
Data Sheet
6
2003-04-25
V23818-M305-B57
Description
Regulatory Compliance
Feature
Standard
Comments
Compliant with
89/336/EEC
EN 55022
EN 55024
File: 1400
ESD:
EIA/JESD22-A114-B
Class 1C
Electrostatic Discharge (MIL-STD 883D
to the Electrical Pins
method 3015.7)
Immunity:
EN 61000-4-2
IEC 61000-4-2
Discharges ranging from 2 kV to
15 kV on the receptacle cause no
damage to transceiver (under
recommended conditions).
Against Electrostatic
Discharge (ESD) to the
Duplex LC Receptacle
Immunity:
Against Radio
Frequency
EN 61000-4-3
IEC 61000-4-3
With a field strength of 3 V/m, noise
frequency ranges from 10 MHz to
2 GHz. No effect on transceiver
performance between the
Electromagnetic Field
specification limits.
Emission:
Electromagnetic
Interference (EMI)
FCC 47 CFR
Noise frequency range:
30 MHz to 18 GHz
Part 15, Class B
EN 55022 Class B
CISPR 22
This device complies with part 15 of
the FCC Rules. Operation is subject
to the following two conditions:
1 This device may not cause
harmful interference.
SFP
V23818-M305-B57
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
File: 1402
2 This device must accept any
interference received, including
interference that may cause
undesired operation.
Data Sheet
7
2003-04-25
V23818-M305-B57
Technical Data
Technical Data
Absolute Maximum Ratings
Parameter
Symbol
Limit Values
Unit
min.
max.
0.5
Package Power Dissipation
Data Input Levels
W
V
VCC+0.5
5
Differential Data Input Voltage Swing
Storage Ambient Temperature
VCC max
VIDpk-pk
–40
85
°C
V
5.5
ECL-Output Current Data
50
mA
Exceeding any one of these values may destroy the device immediately.
Recommended Operating Conditions
Parameter
Symbol
Limit Values
typ.
Unit
min.
max.
85
Case Temperature
Power Supply Voltage
Transmitter
TC
–10
°C
VCC–VEE 3.1
3.3
3.5
V
Differential Data Input Voltage VIDpk-pk 500
3200
mV
Swing
Receiver
Input Center Wavelength
lC
770
860
nm
The electro-optical characteristics described in the following tables are valid only for use
under the recommended operating conditions.
Data Sheet
8
2003-04-25
V23818-M305-B57
Technical Data
Transmitter Electro-Optical Characteristics
Transmitter
Symbol
Limit Values
Unit
min.
typ.
max.
Launched Power (Average)1)
Optical Modulation Amplitude2) OMA
PO
–9.5
–6
–4
dBm
µW
2.125 Gbit/s
1.25/1.0625 Gbit/s
196
156
450
450
Center Wavelength
Spectral Width (RMS)
Relative Intensity Noise
Extinction Ratio (Dynamic)
Total Tx Jitter
lC
830
850
860
nm
sI
0.85
–117
RIN
ER
TJ
dB/Hz
dB
9
13
40
80
ps
Reset Threshold3)
Reset Time Out3)
VTH
tRES
tR
2.5
2.75
240
2.99
560
150
65
V
140
ms
ps
Rise Time, 20% - 80%
Supply Current
45
mA
1)
Into multimode fiber, 62.5 µm or 50 µm diameter.
Fibre Channel PI Standard.
Laser power is shut down if power supply is below VTH and switched on if power supply is above VTH after tRES
2)
3)
.
Receiver Electro-Optical Characteristics
Receiver
Symbol
Limit Values
typ.
Unit
min.
max.
Sensitivity (Average Power)1)
2.125 Gbit/s
1.25/1.0625 Gbit/s
PIN
dBm
–18.5
–19.5
–16
–17
Saturation (Average Power)
PSAT
0
dBm
µW
Min. Optical Modulation
Amplitude2)
OMA
2.125 Gbit/s
1.0625 Gbit/s
24
19
49
31
Stressed Receiver Sensitivity
50 µm Fiber3)
SPIN
50 µm
µW
2.125 Gbit/s
1.0625 Gbit/s
29
24
96
55
Data Sheet
9
2003-04-25
V23818-M305-B57
Technical Data
Receiver Electro-Optical Characteristics (cont’d)
Receiver
Symbol
Limit Values
Unit
min.
typ.
max.
Stressed Receiver Sensitivity
62.5 µm Fiber3)
SPIN
62.5 µm
µW
2.125 Gbit/s
1.0625 Gbit/s
34
32
109
67
Loss Of Signal (LOS)
Assert Level4)
PLOSA
PLOSD
–30
–25
–23
2
dBm
dBm
dB
Loss Of Signal (LOS)
Deassert Level5)
–18
Loss Of Signal (LOS) Hysteresis PLOSA
–PLOSD
0.5
Loss Of Signal (LOS)
Assert Time
tASS
100
350
2.5
6
µs
Loss Of Signal (LOS)
Deassert Time
tDAS
µs
Receiver 3 dB cut off
Frequency2)
GHz
GHz
mV
Receiver 10 dB cut off
Frequency2)
Differential Data Output Voltage VODpk-pk 500
700
80
1230
Swing6)
Return Loss of Receiver
Supply Current7)
ORL
12
dB
90
mA
1)
Average optical power at which the BER is 1x10–12. Measured with a 27–1 NRZ PRBS and ER = 9 dB.
Fibre Channel PI Standard.
2)
3)
Measured at the given Stressed Receiver Eye Closure Penalty and DCD component given in Fibre Channel
PI Standard (2.03/2.18 dB & 40/80 ps).
An increase in optical power above the specified level will cause the LOS output to switch from a high state to
a low state.
A decrease in optical power below the specified level will cause the LOS to change from a low state to a high
state.
AC/AC for data. Load 50 W to GND or 100 W differential. For dynamic measurement a tolerance of 50 mV
should be added.
4)
5)
6)
7)
Supply current excluding Rx output load.
Data Sheet
10
2003-04-25
V23818-M305-B57
Technical Data
Timing of Control and Status I/O
Parameter
Symbol
Limit Values Unit
Condition
min.
max.
Tx Disable
Assert Time
t_off
10
µs
Time from rising edge of Tx
Disable to when the optical
output falls below 10% of
nominal.
Tx Disable
Negate Time
t_on
1
ms
Time from falling edge of Tx
Disable to when the modulated
optical output rises above 90%
of nominal.
Time to Initialize, t_init
Including Reset
of Tx Fault
300
100
From power on or negation of
Tx Fault using Tx Disable.
Tx Fault Assert t_fault
Time
µs
Time from fault to Tx Fault on.
Tx Disable to
Reset
t_reset
10
Time Tx Disable must be held
high to reset Tx Fault.
LOS Assert Time t_loss_on
100
100
100
Time from LOS state to Rx
LOS assert.
LOS Deassert
Time
t_loss_off
Time from non-LOS state to Rx
LOS deassert.
I2C Bus
Clock Rate
f_i2cbus_
clock
kHz
Data Sheet
11
2003-04-25
V23818-M305-B57
Eye Safety
Eye Safety
This laser based single mode transceiver is a Class 1 product.
It complies with IEC 60825-1 and FDA 21 CFR 1040.10 and 1040.11.
To meet laser safety requirements the transceiver shall be operated within the Absolute
Maximum Ratings.
Attention: All adjustments have been made at the factory prior to shipment of the
devices. No maintenance or alteration to the device is required.
Tampering with or modifying the performance of the device will result
in voided product warranty.
Note: Failure to adhere to the above restrictions could result in a modification that is
considered an act of “manufacturing”, and will require, under law, recertification of
the modified product with the U.S. Food and Drug Administration (ref. 21 CFR
1040.10 (i)).
Laser Data
Wavelength
850 nm
Total Output Power
< 675 µW
(as defined by IEC: 7 mm aperture at 14 mm distance)
Total Output Power
< 70 µW
(as defined by FDA: 7 mm aperture at 20 cm distance)
Beam Divergence
12°
FDA
IEC
Complies with 21 CFR
1040.10 and 1040.11
Class 1 Laser Product
File: 1401
Figure 3
Required Labels
Indication of
laser aperture
and beam
20
11
Tx
Top view
Rx
File: 1333
Figure 4
Laser Emission
Data Sheet
12
2003-04-25
V23818-M305-B57
Application Notes
Application Notes
EMI-Recommendations
To avoid electromagnetic radiation exceeding the required limits please take note of the
following recommendations.
When Gigabit switching components are found on a PCB (multiplexers, clock recoveries
etc.) any opening of the chassis may produce radiation also at chassis slots other than
that of the device itself. Thus every mechanical opening or aperture should be as small
as possible.
On the board itself every data connection should be an impedance matched line (e.g.
strip line, coplanar strip line). Data, Datanot should be routed symmetrically, vias should
be avoided. A terminating resistor of 100 W should be placed at the end of each matched
line. An alternative termination can be provided with a 50 W resistor at each (D, Dn). In
DC coupled systems a thevenin equivalent 50 W resistance can be achieved as follows:
for 3.3 V: 125 W to VCC and 82 W to VEE, for 5 V: 82 W to VCC and 125 W to VEE at Data
and Datanot. Please consider whether there is an internal termination inside an IC or a
transceiver.
In certain cases signal GND is the most harmful source of radiation. Connecting chassis
GND and signal GND at the plate/bezel/chassis rear e.g. by means of a fiber optic
transceiver/cage may result in a large amount of radiation. Even a capacitive coupling
between signal GND and chassis may be harmful if it is too close to an opening or an
aperture.
If a separation of signal GND and chassis GND is not planned, it is strongly
recommended to provide a proper contact between signal GND and chassis GND at
every location where possible. This concept is designed to avoid hotspots. Hotspots are
places of highest radiation which could be generated if only a few connections between
signal and chassis GND exist. Compensation currents would concentrate at these
connections, causing radiation.
By use of Gigabit switching components in a design, the return path of the RF current
must also be considered. Thus a split GND plane of Tx and Rx portion may result in
severe EMI problems.
The cutout should be sized so that all contact springs of the cage make good contact
with the face plate.
For the SFP transceiver a connection of the SFP cage pins to chassis GND is
recommended. If no separate chassis GND is available on the users PCB the pins
should be connected to signal GND. In this case take care of the notes above.
Please consider that the PCB may behave like a waveguide. With an er of 4, the
wavelength of the harmonics inside the PCB will be half of that in free space. In this
scenario even the smallest PCBs may have unexpected resonances.
Data Sheet
13
2003-04-25
V23818-M305-B57
Application Notes
The SFP transceiver can be assembled onto the host board together with all cages and
host board connectors complying with the SFP multi source agreement.
Infineon Proposes
Cage:
Host board connector:
Tyco Electronics
Part Number: 1367073-1
Infineon Technologies
Part Number: V23838-S5-N1
Cage
SFP
Host board
connector
File: 1502
Figure 5
Data Sheet
14
2003-04-25
V23818-M305-B57
Application Notes
Handling Notes
INSTALLING
FRONT BEZEL
DOOR IS CLOSED
SFP CAGE
PUSH
HOST PCB
REMOVING
STEP 1
FRONT BEZEL
SFP CAGE
DOOR
HOST PCB
STEP 2
PULL
File: 1504
Figure 6
Installing and Removing of SFP-Transceiver
Data Sheet
15
2003-04-25
V23818-M305-B57
Application Notes
EEPROM Serial ID Memory Contents
Data Address Hex
MSA Name/Description
Content/Value
0
03
04
07
00
00
00
01
20
40
0C
05
01
15
00
00
00
32
0F
00
00
Transceiver type
Extended identifier
Connector type
Reserved
SFP
1
Serial ID
LC
2
3
4
SONET OC-48
SONET OC-3/12
Gigabit Ethernet
FC reach/technology
FC technology
5
6
7
8
9
FC media
10
FC speed
11
Encoding
12
Nominal bit rate
Reserved
13
14
Length (9 µm) x 1 km
Length (9 µm) x 100 m
Length (50 µm) x 10 m
Length (62.5 µm) x 10 m
Length (copper) x 1 m
Reserved
15
16
17
18
19
20 - 35
36
Vendor name
Infineon AG
00
Reserved
37 - 39
40 - 55
56
Vendor IEEE OUI
Vendor part number
Vendor revision
Vendor revision
Wavelength
00-03-19
V23818-M305-B57
Infineon production code
57 - 59
60 - 61
62
1.0
850
00
Reserved
63
Check code (0 to 62)
Reserved
64
00
1A
69
32
65
Transceiver options
Upper bit rate margin (%)
Lower bit rate margin (%)
Vendor serial number
Vendor date code
Tx Disable, Tx Fault, LOS
66
67
68 - 83
84 - 91
92 - 94
95
Diagnostic / SFF-8472 compliance Not implemented
Check code (64-94)
96 - 127
00
Vendor specific data
Data Sheet
16
2003-04-25
V23818-M305-B57
Application Notes
Multimode 850 nm Fibre Channel SFP Transceiver, AC/AC TTL
1 µH
1) Design criterion of the capacitor used is
the resonant frequency and its value must
be in the order of the nominal data rate.
Short trace lengths are mandatory.
V
T
CC
0.1 µF
1)
1)
xx nF
V
T
EE
1 µH
3.3 V
10 µF
V
R
CC
0.1 µF
10 µF
0.1 µF
xx nF
V
R
EE
Host Board
SFP Module
File: 1304
Figure 7
Recommended Host Board Supply Filtering Network
Infineon
3.3 V
1 µH
1 µH
SFP
Transceiver
10 µF 0.1 µF
Protocol V
16
CC
V
T
CC
1)
xx nF
Protocol V
CC
4.7 to
10 kΩ
0.1 µF
4.7 to
10 kΩ
17
Tx Disable
Tx Fault
Tx Disable
Tx Fault
0.01 µF
TD–
Laser
Driver
100 Ω
TD+
0.01 µF
V
T
EE
15
V
R
1)
CC
4.7 to
10 kΩ
xx nF
Protocol IC
SerDes IC
10 µF 0.1 µF
14
0.01 µF
0.01 µF
RD+
1)
xx nF
100 Ω
Preamp &
Quantizer
RD–
LOS
LOS
3.3 V
V
R
EE
4.7 to
4.7 to
4.7 to
10 kΩ
10 kΩ
10 kΩ
MOD-DEF(0)
MOD-DEF(1)
MOD-DEF(2)
PLD / PAL
1) Design criterion of the capacitor used is the resonant frequency and its value must
be in the order of the nominal data rate. Short trace lengths are mandatory.
File: 1305
Figure 8
Example SFP Host Board Schematic
Data Sheet
17
2003-04-25
V23818-M305-B57
Package Outlines
Package Outlines
55.9
[2.200]
13.7
[.538]
10.4
[.411]
6.25
[.246]
Dimensions in mm [inches]
File: 1207
Figure 9
Data Sheet
18
2003-04-25
V23818-M305-B57
Revision History:
2003-04-25
DS1
Previous Version:
2002-01-24
Page
Subjects (major changes since last revision)
Document completely revised
For questions on technology, delivery and prices please contact the Infineon
Technologies Offices in Germany or the Infineon Technologies Companies and
Representatives worldwide: see our webpage at http://www.infineon.com.
Edition 2003-04-25
Published by Infineon Technologies AG,
St.-Martin-Strasse 53,
D-81541 München, Germany
© Infineon Technologies AG 2003.
All Rights Reserved.
Attention please!
The information herein is given to describe certain components and shall not be considered as warranted
characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding
circuits, descriptions and charts stated herein.
Infineon Technologies is an approved CECC manufacturer.
Information
For further information on technology, delivery terms and conditions and prices please contact your nearest
Infineon Technologies Office in Germany or our Infineon Technologies Representatives worldwide.
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devices or systems with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life-support
devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
相关型号：
V23818-M305-L57
Small Form Factor Multimode 850 nm 2.125 and 1.0625 GBd Fibre Channel 2x5 Transceiver with LC⑩ Connector
INFINEON
V23818-N15-L16
Small Form Factor Single Mode 1300 nm Multirate up to 2.5 Gbit/s Transceiver 2x5/2x10 Pinning with LC⢠Connector
INFINEON
V23818-N15-L17
Small Form Factor Single Mode 1300 nm Multirate up to 2.5 Gbit/s Transceiver 2x5/2x10 Pinning with LC⢠Connector
INFINEON
V23818-N15-L353
Small Form Factor Single Mode 1300 nm Multirate up to 2.5 Gbit/s Transceiver 2x5/2x10 Pinning with LC⢠Connector
INFINEON
V23818-N15-L354
Small Form Factor Single Mode 1300 nm Multirate up to 2.5 Gbit/s Transceiver 2x5/2x10 Pinning with LC⢠Connector
INFINEON
V23818-N15-L355
Small Form Factor Single Mode 1300 nm Multirate up to 2.5 Gbit/s Transceiver 2x5/2x10 Pinning with LC⢠Connector
INFINEON
V23818-N15-L356
Small Form Factor Single Mode 1300 nm Multirate up to 2.5 Gbit/s Transceiver 2x5/2x10 Pinning with LC⢠Connector
INFINEON
V23818-N15-L356-C
Small Form Factor Single Mode 1300 nm Multirate up to 2.5 Gbit/s Transceiver 2x5/2x10 Pinning with LC⢠Connector
INFINEON
V23818-N15-L36
Small Form Factor Single Mode 1300 nm Multirate up to 2.5 Gbit/s Transceiver 2x5/2x10 Pinning with LC⢠Connector
INFINEON
©2020 ICPDF网 联系我们和版权申明