DBDA-25S-F0 [ITT]

D Subminiature Connector, 25 Contact(s), Female, Crimp Terminal, Receptacle,;


型号：	DBDA-25S-F0
厂家：	ITT Cannon
描述：	D Subminiature Connector, 25 Contact(s), Female, Crimp Terminal, Receptacle, 连接器
文件：	总5页 (文件大小：131K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Environmental D

D*D

The Cannon D*D Environmental Series is designed der and crimp versions, all assemblies are provided

to meet the demand for sealed subminiature rectan- with nylon potting cups and dust caps.

gular plugs with superior vibration and moisture

Solder type contacts are non-removable and are

resistance characteristics for aircraft, missile, and

factory-installed. Crimp type connectors utilize the

ground support equipement applications.

field-proven LITTLE CAESAR® rear insertion, rear-

Featureing a rugged aluminum shell and peripheral

seal, the D*D conenctor meets all applicable re-

quirements of MIL-C-24308. Available in both sol-

release retention system.

PLEASE NOTE: The D*D Series is not intermate-

able with other D Subminiature connectors.

Performance and Material Specifications

Shell

Aluminum, cadmium plated with yellow chromate supplementary coating.

Contacts

Solder pot: Copper alloy, gold plated .00002 (0.0005) over nickel .00004 (0.0010). Cirmp type. Copper

alloy, gold plated .00002 (0.0005) over nickel .00004 (0.0010)

Insulator

Diallyl phthalate, per MIL-M-14, Type MDG or SDG-F

Contact Termination

Solder pot accommodating up to #20 AWG stranded wire. Crimp type accommodating #20, #22 and

#24 AWG stranded wire.

Socket Type

Closed entry

Float Mounting Rivets & Washers

Stairless steel Passivated per QQ-P-35

Test Data

Specifications

Voltage Rating

All voltage figures are AC (rms). 60 Hz measured at approximately 25.0˚C 50% RH

Greater than 5,000 megohms, determined in accordance will MIL-STD-202A, Method 302.

Insulation Resistance

(per MIL-C-24308)

Contact Voltage Drop

2.67 millivolts, maximum, per amp.

Contact Separation Force

Air Leakage

1 to 8 ounces when tested in accordance with MIL-C-24308.

When properly wired and potted, 1 cubic inch of air per hour max. when subjected to 30 PSI pressure

differential in accordance with MIL-C-5015D, Paragraphc 4.5.3.1

Vibration

Exceeds test requirements of MIL-STD-202A, Method 204, Condition D.

(per MIL-C-24308)

Corrosion Resistance

(per MIL-C-24308)

Exceeds requirements of 50 hour exposure to salt spary in accordance with MIL-STD-202A, Method

101A, Condition B.

Moisture Resistance

(per MIL-C-24308)

Exceeds requirements of MIL-STD-202A. Method 106.

Shock

Exceeds requirements of MIL-STD-202A, Method 213. Condition G

Effective from full engagement to 1/16 short of full engagement.

Environmental Seal

Contact Retention Force

(Crimp type) 8 pounds (35.6 newtons) minimum of first cycles: 5 pounds (22.2 newtons) minimum after

tenth cycle.

Standard Layout Plugs

Measured from cotact-to-contact, and contact-to-shell or unmated condition.

AlTITUDE (FEET)

Sea

Level

20,000

50,000

70,000

Average

Flash-

over

1700

1000

650

500

Test

1250

750

475

375

See Commerical D Subminiature catalog for additional Combo D options. including 75 ohm Coax.

Dimensions are shown in inches (millimeters).

Dimensions subject to change.

www.ittcannon.com

359

Environmental D

D*D

How to Order

D - 15

Solder Cup Terminals

SERIES PREFIX

SHELL SIZE

CLASS

CONTACT ARRANGEMENT

CONTACT TYPE

MOUNTING STYLE

MODIFICATION

CLASS

SERIES PREFIX

MOUNTING STYLE

ITT Cannon Designation

D - Environmental

A - Standard mounting holes

B - Float mounts supplied

CONTACT ARRANGEMENT

SHELL SIZE

A, B, C, D, E

9, 15, 25, 37, 50

MODIFICATION

Consult factory

CONTACT TYPE

P - Pin

S -Socket

DA F- 15 P- F0

Snap-In Crimp Terminals

SERIES PREFIX

SHELL SIZE

CLASS

MOUNTING STYLE

CONTACT ARRANGEMENT

CONTACT TYPE

MODIFICATION

SERIES PREFIX

CLASS

CONTACT TYPE

ITT Cannon Designation

DA - Enviromental, crimp type

P - Pin

S - Socket

SHELL SIZE

MOUNTING STYLE

No Designator - Standard mounting

MODIFICATION

A, B, C, D, E

F0 - Connector supplied less contacts, for othe

F - Float mounts supplied

modifications consult factory.

CONTACT ARRANGEMENT

9, 15, 25, 37, 50

Contact Arrangements

Faces View Pin Insert

10 11 12 13

10 11 12 13 14 15

14 15 16 17 18 19 20 21 22 23 24 25

Shell Size

Contact Arrangement

Contact Size

#20

10 11 12 13 14 15 16 17

10 11 12 13 14 15 16 17 18 19

20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37

34 35 36 37 38 39 40 41 42 43 46 45 46 47 48 49 50

Shell Size

#20

Contact Arrangement

Contact Size

Dimensions are shown in inches (millimeters).

Dimensions subject to change.

www.ittcannon.com

360

Environmental D

D*D

Shell Dimensions, Standard Mount

Receptacle

10˚ TYP.

.120 +_ .005 DIA.

(3.05 +_ 0.13)

2 MTG. HOLES

.677 (17.20) MAX.

CONTACT EXTENSION

A MAX.

MAX.

.061 +_ .005

(1.55 +_ 0.13)

.874

(22.20)

MAX.

K +_ .005

( +_ .013)

.058 +_ .005

(1.47 +_ .013)

.109 (2.77) FL. TYP.

Plug

.299 (7.59)

MAX.

CONACT

EXTENSION

.120 +_ .005 DIA.

(3.05 +_ 0.13)

2 MTG. HOLES

MAX.

10˚ TYP.

A MAX.

.061 +_ .005

(1.55 +_ 0.13)

.904

(22.96)

MAX.

.677

(17.20)

.109 (2.77)

R. TYP

K +_ .005

( +_ .013)

.425 +_ .005

(10.80 +_ 0.13)

.089 +_ .005

(2.26 +_ 0.13)

Float Mount Dimensions

Receptacle

.120 +_ .005 DIA.

(3.05 +_ 0.13)

2 MTG. HOLES

MAX.

.677 (17.20) MAX.

CONTACT

EXTENSION

.032 (0.81)

TOTAL

DIA. FLOAT

10˚ TYP.

A MAX.

.874

(22.20)

MAX.

K +_ .005

( +_ .013)

.061 +_ .005

(1.55 +_ 0.13)

.031 +_ .005

(0.79 +_ 0.13)

.058 +_ .005

(1.47 +_ .013)

.109 (2.77) R. TYP.

Plug

.299 (7.59) MAX.

CONACT

EXTENSION

.032 (0.81)

TOTAL

.120 +_ .005 DIA.

(3.05 +_ 0.13)

MAX.

10˚ TYP.

MAX.

DIA. FLOAT

2 MTG. HOLES

.061 +_ .005

(1.55 +_ 0.13)

.904

(22.96)

MAX.

.677

(17.20)

.031 +_ .005

(0.79 +_ 0.13)

.109 (2.77)

R. TYP

K +_ .005

( +_ .013)

.089 +_ .005

(2.26 +_ 0.13)

.425 +_ .005

(10.80 +_ 0.13)

NOTE: All D*D Environmental plugs and receptacles are provided with dust caps and removable potting cups.

Shell Size

Max.

+_ .005 (0.13)

+_ .010 (0.25)

DED-9P

.915 (23.24)

1.233 (31.32)

1.786 (45.36)

2.458 (62.43)

2.390 (60.71)

.596 (15.14)

.567 (14.40)

.680 (17.27)

1.125 (28.58)

1.437 (36.50)

1.993 (50.62)

2.625 (66.68)

2.531 (64.29)

1.442 (36.63)

1.755 (44.58)

2.295 (58.29)

2.937 (74.60)

2.859 (72.62)

.614 (15.60)

.735 (18.67)

.825 (20.86)

1.143 (29.03)

1.683 (42.75)

2.343 (59.51)

2.251 (57.18)

.483 (12.27)

.596 (15.14)

DED-9S

DAD-15P

DAD-15S

DBD-25P

DBD-25S

DCD-37P

DCD-37S

DDD-50P

DDD-50S

All tolerances are +_ .010 (0.24) unless noted otherwise.

Dimensions are shown in inches (millimeters).

Dimensions subject to change.

www.ittcannon.com

361

Environmental D

D*D

Mounting Dimensions

.324 +_ .010˚

(8.23 +_ 0.25)

.189 +_ .015˚

(4.80 +_ 0.38)

.292 +_ .010˚

(7.42 +_ 0.25)

.133 +_ .010˚

(3.38 +_ .025)

FRONT

REAR

PLUG

RECEPT

Figure 1

Figure 2

Figure 3

Figure 4

4-40 NC2A THREAD

PLUG

.280 +_ .013˚

(7.11 +_ 0.32)

.230 +_ .013˚

(5.85 +_ 0.32)

.230 +_ .013˚

(5.85 +_ 0.32)

.194 +_ .008˚

(4.94 +_ 0.19)

PLUG

RECEPT

Figure 6

Figure 8

Figure 5

Figure 7

NOTE: Max panel thickness is .125 (3.17) for

non-floating rear panel mounting.

With plug assembly front mounted and recepta-

With plug assembly rear mounted (float rivets)

and receptacle assembly front mounted, use

hardware from Figures 2 and 3.

cle assembly rear mounted, use hardware from

Figures 5 and 6.

With both connectors rear mounted, ues #4-40

flat head screws flush with the panel (Fig. 1).

With both connectors front mounted, use #4-40

binder or pan head screws (Fig. 2).

With plug assembly front mounted and recepta-

cle assembly rear mounted (plug assembly has

float mounting screw), use hardware fron figure

1 for receptacle assembly.

Electrical contact engagement when mounted

per Figure 1 is .046 (1.17) min./.070(1.78) max.

NOTE: Float rivets are for rear mounting only and

float screw for front mounting only. (Specify when

ordering.)

With both connectors rear mounted (float rivets

on plug assembly side); use #4-40 flat head

scerws, flush with the panel (Fig. 3).

* Dimensions between panels represent the rec-

ommended limit to be used in the design of the

connector mounting method.

With both connecotrs front mounted (plug as-

sembly has float mounting screw), use #4-40

binder or pan head screws for receptacle as-

sembly (Fig. 4)

With plug assembly rear mounted and receptaccle

assembly front mounted, use hardware from

Figures 1 and 2.

Panel Cutouts

USE .120(3.05) DIA. HOLE OR 4-40 TAP (CUSTOMER PREFERENCE) FOR FRONT MOUNTING.

FOR REAR MOUNTING USE .120(3.05) DIA. HOLE COUNTERSUNK FOR FLATHEAD SCREW.

.083(2.11) R. MAX.

TYPICAL

Shell Size

DED-9

+_ .010 (0.25)

1.442 (36.63)

1.755 (44.58)

2.295 (58.29)

2.937 (74.60)

2.859 (72.62)

Min.

+_ .010 (0.25)

Min.

+_ .006 (0.15)

.614 (15.60)

.735 (18.67)

.497 (12.62)

1.125 (28.58)

1.437 (36.50)

1.993 (50.62)

2.625 (66.68)

2.531 (64.29)

.839 (21.31)

1.157 (29.39)

1.697 (43.10)

2.357 (59.87)

2.265 (57.53)

.497 (12.62)

.610 (15.49)

DAD-15

DBD-25

DCD-37

DDD-50

Add .032 (0.81) to dimensions C and E for float mounting.

Note: Panel cutout does not allow for potting cup clearance.

Dimensions are shown in inches (millimeters).

Dimensions subject to change.

www.ittcannon.com

362

Environmental D

D*D

Contact Crimping Information

Semi-Automatic Crimp Machines

Crimp Type Contacts

Contact

Size

Wire Size

Accom.

Standard Finish

Military Finish

Socket

20, 22, 24

330-5291-015

031-1007-000

330-5291-079

031-1007-042

CIET-20HD

Insertion/Extraction Tools

Contact

Plastic Insertion/Extraction

Plastic Extraction

Size

AWG

Part No.

Description

Part No.

Description

CBT-646

20, 22, 24

980-2000-426

CIET-20HD

323-7010-000

CET-20-11

The CBT-646, Vibra-Bowl Crimper is

pneumat-

ically powered, electoronically controlled machine. It

is designed to semi-automatically crimp closed

barrel, machined contacts, as used in the aerospace

and commercial industries. The machine will ac-

commodate wire sizes 30 thru 12 AWG. The

CBT-646 is actuated automatically upon insertion

of a pre-stripped stranded or single conductor wire.

The CBT-646 meets all Mil. Spec. requirements for

crimping closed barrel contacts.

Hand Crimp Tools

M22520/1-01

M22520/2-01

Crimp Tool

Locator

Contact

Size

Machine Crimp Rage: 1300 + per hour

AWG

Part No.

Description

M22520/2-01

M22520/1-01

Part No.

Description

M22520/2-08

TH25

995-0001-584

995-0001-585

995-0001-604

995-0001-244

Power Requirements:

20, 22, 24

Electrical = 115 Vac, 60 Hz, 5A

Pneumatic = 85 psi, 2 cu. ft. per min.

Products: Most ITT Cannon Commercial and Aero-

space closed-barrel contacts, wire sizes 30 thru 12

AWG. See connector line for part numbers.

Assembly Instructions

Wire Stripping-

Contact Crimping

Contact Insertion

Machined Contacts

Min.

Max.

.188 (4.78)

.208 (5.28)

1. Cut wires to length. Strip insulation per above illustration. Check 2. Insert contact and wires into poper crimp tool (and locator, if 3. Center wired contact in groove of insertion tool with tool tip

for broken or frayed wires.

required). Crimp contact to wires. Inspect crimp.

butting contact shoulder. Insert contact into cavity until a positive

stop is felt. Inspection insertion.

Contact Extraction

4. To be sure contact is locked securely, pull back lightly on wire. 5. Place wire into extraction tool tip.

Repeat for balance of contacts working row by row across the

insulator.

6. Insert tool tip into contact cavity until tip bottoms against contact

shoulder, releasing tines. Hold wires against tool with finger and

remove tool and contact. Repeat for balance of contacts.

Dimensions are shown in inches (millimeters).

Dimensions subject to change.

www.ittcannon.com

363

DBDA-25S-F0 [ITT]

相关型号：

DBDAF-25P-F0

DBDD1200S33K2C20

DBDD200S33K2C20

DBDD200S65K1

DBDD400S33K2C20

DBDD400S65K1

DBDD600S65K1

DBDD800S33K2C20

DBDDB6U145N

DBDDB6U205N

DBDDB6U215N

DBDDB6U85N