MMFT960T1 [MOTOROLA]
MEDIUM POWER TMOS FET 300 mA 60 VOLTS; 中功率FET TMOS 300毫安60伏型号: | MMFT960T1 |
厂家: | MOTOROLA |
描述: | MEDIUM POWER TMOS FET 300 mA 60 VOLTS |
文件: | 总6页 (文件大小:125K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Order this document
by MMFT960T1/D
SEMICONDUCTOR TECHNICAL DATA
Motorola Preferred Device
N–Channel Enhancement–Mode
Silicon Gate TMOS
SOT–223 for Surface Mount
MEDIUM POWER
TMOS FET
300 mA
60 VOLTS
This TMOS medium power field effect transistor is designed for
high speed, low loss power switching applications such as
switching regulators, dc–dc converters, solenoid and relay drivers.
The device is housed in the SOT–223 package which is designed
for medium power surface mount applications.
R
= 1.7 OHM MAX
DS(on)
•
•
•
•
Silicon Gate for Fast Switching Speeds
= 1.7 Ohm Max
4
R
DS(on)
1
2
2,4 DRAIN
Low Drive Requirement
3
The SOT–223 Package can be soldered using wave or reflow.
The formed leads absorb thermal stress during soldering
eliminating the possibility of damage to the die.
CASE 318E–04, STYLE 3
TO–261AA
•
Available in 12 mm Tape and Reel
Use MMFT960T1 to order the 7 inch/1000 unit reel
Use MMFT960T3 to order the 13 inch/4000 unit reel
1
GATE
3 SOURCE
MAXIMUM RATINGS (T = 25°C unless otherwise noted)
C
Rating
Drain–to–Source Voltage
Symbol
Value
60
Unit
Volts
Volts
mAdc
V
V
DS
Gate–to–Source Voltage — Non–Repetitive
Drain Current
±30
300
GS
I
D
(1)
Total Power Dissipation @ T = 25°C
Derate above 25°C
P
D
0.8
6.4
Watts
mW/°C
A
Operating and Storage Temperature Range
T , T
–65 to 150
°C
J
stg
DEVICE MARKING
FT960
THERMAL CHARACTERISTICS
Thermal Resistance — Junction–to–Ambient
R
156
°C/W
θJA
Maximum Temperature for Soldering Purposes
Time in Solder Bath
T
L
260
10
°C
Sec
1. Device mounted on a FR–4 glass epoxy printed circuit board using minimum recommended footprint.
TMOS is a registered trademark of Motorola, Inc.
Thermal Clad is a trademark of the Bergquist Company
Preferred devices are Motorola recommended choices for future use and best overall value.
REV 3
Motorola, Inc. 1997
ELECTRICAL CHARACTERISTICS (T = 25°C unless otherwise noted)
A
Characteristic
Symbol
Min
Typ
Max
Unit
OFF CHARACTERISTICS
Drain–to–Source Breakdown Voltage
V
60
—
—
—
—
—
—
10
50
Vdc
µAdc
nAdc
(BR)DSS
(V
GS
= 0, I = 10 µA)
D
Zero Gate Voltage Drain Current
(V = 60 V, V = 0)
I
DSS
DS
Gate–Body Leakage Current
(V = 15 Vdc, V = 0)
GS
I
GSS
GS
DS
(1)
ON CHARACTERISTICS
Gate Threshold Voltage
V
1.0
—
—
—
3.5
1.7
Vdc
Ohms
Vdc
GS(th)
DS(on)
DS(on)
(V
DS
= V , I = 1.0 mAdc)
GS
D
Static Drain–to–Source On–Resistance
(V = 10 Vdc, I = 1.0 A)
R
V
GS
D
Drain–to–Source On–Voltage
(V
GS
(V
GS
= 10 V, I = 0.5 A)
—
—
—
—
0.8
1.7
D
= 10 V, I = 1.0 A)
D
Forward Transconductance
(V = 25 V, I = 0.5 A)
g
—
600
—
mmhos
pF
fs
DS
D
DYNAMIC CHARACTERISTICS
Input Capacitance
C
—
—
—
—
—
—
65
33
—
—
—
—
—
—
iss
(V
DS
= 25 V, V
= 0,
GS
f = 1.0 MHz)
Output Capacitance
Transfer Capacitance
Total Gate Charge
C
oss
C
7.0
3.2
1.2
2.0
rss
Q
nC
g
(V
GS
= 10 V, I = 1.0 A,
D
V
Gate–Source Charge
Gate–Drain Charge
Q
gs
gd
= 48 V)
DS
Q
1. Pulse Test: Pulse Width ≤ 300 µs, Duty Cycle ≤ 2.0%.
TYPICAL ELECTRICAL CHARACTERISTICS
5
4
3
1
T
= 25°C
J
T
= 25°C
J
T
= –55°C
J
0.8
V
= 10 V
GS
T
= 125°C
J
8 V
7 V
0.6
0.4
0.2
0
2
1
0
6 V
5 V
4 V
V
= 10 V
DS
0
2
4
6
8
10
0
2
4
6
8
10
V
, DRAIN–TO–SOURCE VOLTAGE (VOLTS)
V
, GATE–TO–SOURCE VOLTAGE (VOLTS)
DS
GS
Figure 1. On–Region Characteristics
Figure 2. Transfer Characteristics
2
Motorola Small–Signal Transistors, FETs and Diodes Device Data
TYPICAL ELECTRICAL CHARACTERISTICS
5
4
3
2
1
0
10
V
= 10 V
GS
I = 1 A
D
GS
V
= 10 V
T
= 125
°
C
1
J
25
°C
–55°C
0.1
0
0
0
0.5
1
1.5
2
2.5
–75
–50
–25
0
25
50
75
100
C)
125
150
I
, DRAIN CURRENT (AMPS)
T , JUNCTION TEMPERATURE (
°
D
J
Figure 3. On–Resistance versus Drain Current
Figure 4. On–Resistance Variation with Temperature
250
225
200
175
150
125
V
= 0 V
GS
f = 1 MHz
= 25°C
T
J
1
T
= 125
°
C
T = 25°C
J
J
100
75
0.1
C
iss
C
oss
50
C
25
0
rss
0.3
0.6
0.9
1.2
1.5
0
5
10
15
20
25
30
V
, SOURCE–DRAIN DIODE FORWARD VOLTAGE (VOLTS)
V
DS
, DRAIN–SOURCE VOLTAGE (VOLTS)
SD
Figure 5. Source–Drain Diode Forward Voltage
Figure 6. Capacitance Variation
10
9
8
7
6
5
4
3
2
1
0
2
1.5
1
V
= 10 V
DS
I
T
= 1 A
= 25°C
D
J
V
= 30 V
DS
V
= 48 V
DS
T
= –55°C
J
25°C
0.5
0
125°C
0.5
1
1.5
2
2.5
3
3.5
4
0
0.5
1
1.5
, DRAIN CURRENT (AMPS)
D
2
2.5
Q , TOTAL GATE CHARGE (nC)
I
g
Figure 7. Gate Charge versus Gate–to–Source Voltage
Figure 8. Transconductance
Motorola Small–Signal Transistors, FETs and Diodes Device Data
3
INFORMATION FOR USING THE SOT-223 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must
be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
0.15
3.8
0.079
2.0
0.248
6.3
0.091
2.3
0.091
2.3
0.079
2.0
inches
mm
0.059
1.5
0.059
1.5
0.059
1.5
SOT-223
SOT-223 POWER DISSIPATION
The power dissipation of the SOT-223 is a function of the
dissipation can almost be doubled with this method, area is
taken up on the printed circuit board which can defeat the
pad size. This can vary from the minimum pad size for
soldering to a pad size given for maximum power dissipation.
Power dissipation for a surface mount device is determined
purpose of using surface mount technology. A graph of R
versus collector pad area is shown in Figure 9.
θJA
by T
, the maximum rated junction temperature of the
, the thermal resistance from the device junction to
J(max)
die, R
160
θJA
ambient, and the operating temperature, T . Using the
values provided on the data sheet for the SOT-223 package,
A
Board Material = 0.0625
G-10/FR-4, 2 oz Copper
″
T = 25°C
A
140
120
P
can be calculated as follows:
D
0.8 Watts
T
– T
A
J(max)
R
P
=
D
°
θJA
1.5 Watts
1.25 Watts*
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values into
100
80
the equation for an ambient temperature T of 25°C, one can
A
calculate the power dissipation of the device which in this
case is 0.8 watts.
*Mounted on the DPAK footprint
0.0
0.2
0.4
0.6
0.8
1.0
150°C – 25°C
A, Area (square inches)
P
=
= 0.8 watts
D
156°C/W
Figure 9. Thermal Resistance versus Collector
Pad Area for the SOT-223 Package (Typical)
The 156°C/W for the SOT-223 package assumes the use
of the recommended footprint on a glass epoxy printed circuit
board to achieve a power dissipation of 0.8 watts. There are
other alternatives to achieving higher power dissipation from
the SOT-223 package. One is to increase the area of the
collector pad. By increasing the area of the collector pad, the
power dissipation can be increased. Although the power
Another alternative would be to use a ceramic substrate or
an aluminum core board such as Thermal Clad . Using a
board material such as Thermal Clad, an aluminum core
board, the power dissipation can be doubled using the same
footprint.
4
Motorola Small–Signal Transistors, FETs and Diodes Device Data
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed
or stainless steel with a typical thickness of 0.008 inches.
The stencil opening size for the SOT-223 package should be
the same as the pad size on the printed circuit board, i.e., a
1:1 registration.
circuit board, solder paste must be applied to the pads. A
solder stencil is required to screen the optimum amount of
solder paste onto the footprint. The stencil is made of brass
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
•
•
•
The soldering temperature and time should not exceed
260°C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient should be 5°C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
•
•
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100°C or less.*
•
Mechanical stress or shock should not be applied during
cooling
•
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference should be a maximum of 10°C.
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of control
actual temperature that might be experienced on the surface
of a test board at or near a central solder joint. The two
profiles are based on a high density and a low density board.
The Vitronics SMD310 convection/infrared reflow soldering
system was used to generate this profile. The type of solder
used was 62/36/2 Tin Lead Silver with a melting point
between 177–189°C. When this type of furnace is used for
solder reflow work, the circuit boards and solder joints tend to
heat first. The components on the board are then heated by
conduction. The circuit board, because it has a large surface
area, absorbs the thermal energy more efficiently, then
distributes this energy to the components. Because of this
effect, the main body of a component may be up to 30
degrees cooler than the adjacent solder joints.
settings that will give the desired heat pattern. The operator
must set temperatures for several heating zones, and a
figure for belt speed. Taken together, these control settings
make up a heating “profile” for that particular circuit board.
On machines controlled by a computer, the computer
remembers these profiles from one operating session to the
next. Figure 10 shows a typical heating profile for use when
soldering a surface mount device to a printed circuit board.
This profile will vary among soldering systems but it is a good
starting point. Factors that can affect the profile include the
type of soldering system in use, density and types of
components on the board, type of solder used, and the type
of board or substrate material being used. This profile shows
temperature versus time. The line on the graph shows the
STEP 5
HEATING
ZONES 4 & 7
“SPIKE”
STEP 6
VENT COOLING
STEP 7
STEP 1
PREHEAT
ZONE 1
“RAMP”
STEP 4
HEATING
ZONES 3 & 6
“SOAK”
STEP 2
VENT
“SOAK”
STEP 3
HEATING
ZONES 2 & 5
“RAMP”
205°
TO
219°C
170°C
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
200°C
PEAK AT
SOLDER
JOINT
160°C
150°C
150°C
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
100°C
140°C
MASS OF ASSEMBLY)
100°C
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
50°C
T
TIME (3 TO 7 MINUTES TOTAL)
MAX
Figure 10. Typical Solder Heating Profile
Motorola Small–Signal Transistors, FETs and Diodes Device Data
5
PACKAGE DIMENSIONS
A
F
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
4
2
S
B
INCHES
MILLIMETERS
1
3
DIM
A
B
C
D
F
G
H
J
K
L
M
S
MIN
MAX
0.263
0.145
0.068
0.035
0.126
0.094
MIN
6.30
3.30
1.50
0.60
2.90
2.20
0.020
0.24
1.50
0.85
0
MAX
6.70
3.70
1.75
0.89
3.20
2.40
0.100
0.35
2.00
1.05
10
0.249
0.130
0.060
0.024
0.115
0.087
D
L
G
0.0008 0.0040
J
0.009
0.060
0.033
0
0.014
0.078
0.041
10
C
0.08 (0003)
M
H
0.264
0.287
6.70
7.30
K
STYLE 3:
PIN 1. GATE
2. DRAIN
3. SOURCE
4. DRAIN
CASE 318E–04
ISSUE H
TO-261AA
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specificallydisclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
datasheetsand/orspecificationscananddovaryindifferentapplicationsandactualperformancemayvaryovertime. Alloperatingparameters,including“Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applicationsintended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
ordeathmayoccur. ShouldBuyerpurchaseoruseMotorolaproductsforanysuchunintendedorunauthorizedapplication,BuyershallindemnifyandholdMotorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
Opportunity/Affirmative Action Employer.
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Mfax is a trademark of Motorola, Inc.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315
Mfax : RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MMFT960T1/D
◊
相关型号:
©2020 ICPDF网 联系我们和版权申明