NCV7703CD2G [ONSEMI]
Brush DC Motor Controller;型号: | NCV7703CD2G |
厂家: | ONSEMI |
描述: | Brush DC Motor Controller 电动机控制 光电二极管 |
文件: | 总19页 (文件大小:142K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
NCV7703C
Triple Half-Bridge Driver
with SPI Control
The NCV7703C is a fully protected Triple Half−Bridge Driver
designed specifically for automotive and industrial motion control
applications. The three half−bridge drivers have independent control.
This allows for high side, low side, and H−Bridge control. H−Bridge
control provides forward, reverse, brake, and high impedance states
(with EN = 0). The drivers are controlled via a standard Serial
Peripheral Interface (SPI).
www.onsemi.com
MARKING
DIAGRAM
Features
14
SOIC−14
D2 SUFFIX
CASE 751A
• Ultra Low Quiescent Current in Sleep Mode, 1 mA for V and V
S
CC
NCV7703CG
AWLYWW
14
• 3 High−Side and 3 Low−Side Drivers Connected as Half−Bridges
• Internal Free−Wheeling Diodes
1
1
• Configurable as H−Bridge Drivers
NCV7703C = Specific Device Code
• 500 mA (typ), 1.1 A (max) Drivers
A
WL
Y
WW
G
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
• R
= 0.8 W (typ), 1.7 W (max)
DS(on)
• 5 MHz SPI Control with Daisy Chain Capability
• Compliance with 5 V and 3.3 V Systems
• Overvoltage and Undervoltage Lockout
• Fault Reporting
PIN CONNECTIONS
• 1.45 A Overcurrent Threshold Detection
• 3 A Current Limit
GND
OUT3
GND
OUT1
OUT2
V
CC
EN
• Shoot−Through Attempt Detection
• Overtemperature Warning and Protection Levels
• Internally Fused Leads in SOIC−14 for Better Thermal Performance
• ESD Protection up to 6 kV
V
S
CSB
SI
SCLK
GND
SO
GND
• These are Pb−Free Devices
Typical Applications
• Automotive
ORDERING INFORMATION
Device
Package
Shipping†
• Industrial
• DC Motor Management
NCV7703CD2G
SOIC−14
(Pb−Free)
55 Units / Rail
V
S
V
S
V
S
NCV7703CD2R2G
SOIC−14
(Pb−Free)
2500 /
Tape & Reel
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
M
M
OUT1
OUT2
OUT3
Figure 1. Cascaded Application
© Semiconductor Components Industries, LLC, 2016
1
Publication Order Number:
December, 2016 − Rev. 0
NCV7703C/D
NCV7703C
V
S
DRIVE 1
V
S
V
S
EN
clk
ENABLE
OSC
clk
Charge
Pump
High−Side
Driver
Control
Logic
Waveshaping
V
CC
OUT1
Reference
& Bias
Fault
Detect
V
S
UVLO
Low−Side
Driver
Channel Enable
Waveshaping
SO
Under−Load
Overcurrent
Thermal
16 Bit
Logic
and
SI
Warning/Shutdown
SPI
SCLK
Latch
V
S
clk
DRIVE 2
Channel Enable
Fault
CSB
OUT2
OUT3
V
Undervoltage
Lockout
S
V
S
DRIVE 3
Channel Enable
Fault
clk
V
S
Overvoltage
Lockout
GND
Figure 2. Block Diagram
PACKAGE PIN DESCRIPTION
Pin #
1
Symbol
GND*
Description
Ground. Connect all grounds together.
Half Bridge Output 3.
2
OUT3
3
V
Power Supply input for the output drivers and internal supply voltage.
Chip Select Bar. Active low serial port operation.
Serial Input
S
4
CSB
SI
5
6
SCLK
GND*
GND*
SO
Serial Clock
7
Ground. Connect all grounds together.
Ground. Connect all grounds together.
Serial Output
8
9
10
11
12
13
14
EN
Enable. Logic high wakes the IC up from a sleep mode.
Power supply input for internal logic.
Half Bridge Output 2.
V
CC
OUT2
OUT1
GND*
Half Bridge Output 1.
Ground. Connect all grounds together.
*Pins 1, 7, 8, and 14 are internally shorted together. It is recommended to also short these pins externally.
www.onsemi.com
2
NCV7703C
ENABLE
VBAT
WDI
Wake Up
RESET
Vout
D1*
1N4001
NCV8518
−
D2**
C1
22 mF
Delay
120k
GND
10 mF
V
CC
V
S
OUT1
OUT2
OUT3
EN
C2***
10 nF
M
M
C3***
10 nF
CSB
SI
NCV7703C
SCLK
SO
C4***
10 nF
GND
GND
GND
GND
GND
* D1 optional. For use where reverse battery protection is required.
** D2 optional. For use where load dump exceeds 40V.
*** C2−C4, Recommended for EMC performance.
Figure 3. Application Circuit
www.onsemi.com
3
NCV7703C
MAXIMUM RATINGS
Rating
Value
Unit
Power Supply Voltage (V )
V
S
(DC)
−0.3 to 40
−1
(AC), t < 500 ms, Ivs > −2 A
Output Pin OUTx
(DC)
V
−0.3 to 40
−1
(AC), t < 500 ms, IOUTx > −2 A
Pin Voltage
−0.3 to 5.5
V
A
(Logic Input pins, SI, SCLK, CSB, SO, EN, V
)
CC
Output Current (OUTx)
(DC)
−1.8 to 1.8
−5.0 to 5.0
(AC) (50 ms pulse, 1 s period)
Electrostatic Discharge, Human Body Model,
6
kV
kV
V
V , OUT1, OUT2, OUT3 (Note 3)
S
Electrostatic Discharge, Human Body Model,
all other pins (Note 3)
2
Electrostatic Discharge, Machine Model,
300
200
V , OUT1, OUT2, OUT3 (Note 3)
S
Electrostatic Discharge, Machine Model,
all other pins (Note 3)
V
Operating Junction Temperature
Storage Temperature Range
−40 to 150
−55 to 150
MSL3
°C
°C
−
Moisture Sensitivity Level (MAX 260°C Processing)
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
Thermal Parameters
Test Conditions (Typical Value)
Unit
14 Pin Fused SOIC Package
min−pad board
(Note 1)
1″ pad board
(Note 2)
Junction−to−Lead (psi−JL8, Y ) or Pins 1, 7, 8, 14
23
22
83
°C/W
°C/W
JL8
Junction−to−Ambient (R , q
)
122
q
JA JA
2
1. 1−oz copper, 67 mm copper area, 0.062″ thick FR4.
2
2. 1−oz copper, 645 mm copper area, 0.062″ thick FR4.
3. This device series incorporates ESD protection and is characterized by the following methods:
ESD HBM according to AEC−Q100−002 (EIA/JESD22−A114)
ESD MM according to AEC−Q100−003 (EIA/JESD22−A115)
www.onsemi.com
4
NCV7703C
ELECTRICAL CHARACTERISTICS
(−40°C ≤ T ≤ 150°C, 5.5 V ≤ V ≤ 40 V, 3.15 V ≤ V ≤ 5.25 V, EN = V , unless otherwise specified)
J
S
CC
CC
Characteristic
Conditions
Min
Typ
Max
Unit
GENERAL
Supply Current (V )
V
S
= 13.2 V, OUTx = 0 V
−
1.0
5.0
mA
S
Sleep Mode (Note 5)
EN = SI = SCLK = 0 V, CSB = V
CC
0 V < V < 5.25 V
CC
(T = −40°C to 85°C)
J
V
S
= 13.2 V, OUTx = 0 V
−
−
2.0
mA
EN = SI = SCLK = 0 V, CSB = V
CC
0 V < V < 5.25 V, T = 25°C
CC
J
Supply Current (V )
EN = V , 5.5 V < V < 35 V
−
−
−
−
2.0
0.1
4.0
2.5
mA
mA
mA
V
S
CC
S
Active Mode
No Load
Supply Current (V
)
V
CC
= CSB, EN = SI = SCLK = 0 V
CC
Sleep Mode (Note 6)
(T = −40°C to 85°C)
J
Supply Current (V
Active Mode
)
EN = V
1.5
3.0
CC
CC
V
V
Power−On−Reset Threshold
2.55
2.90
CC
Undervoltage Detection
Threshold V decreasing
3.7
4.1
4.5
V
S
S
Hysteresis
100
365
450
mV
V
Overvoltage Detection
Threshold V increasing
Hysteresis
33.0
1.0
36.5
2.5
40.0
4.0
V
°C
S
S
Thermal Warning (Note 4)
Thermal Shutdown (Note 4)
Threshold
Hysteresis
120
−
140
20
170
−
Threshold
Hysteresis
155
−
175
30
195
−
°C
Ratio of Thermal Shutdown to Thermal
Warning temperature (Note 4)
1.05
1.20
−
°C/°C
OUTPUTS
Output R
Output R
(Source)
(Sink)
I
I
= −500 mA
= 500 mA
−
−
−
−
−
1.7
1.7
−
W
W
DS(on)
DS(on)
out
out
Source Leakage Current
Sum of I(OUTx) x = 1, 2, 3
OUTx = 0 V, V = 40 V, EN = 0 V
−5.0
mA
S
CSB = V
CC
0 V < V < 5.25 V
CC
Sum(I(OUTx)
OUTx = 0 V, V = 40 V, EN = 0 V
−1.0
−
−
S
CSB = V
CC
0 V < V < 5.25 V, T = 25°C
CC
J
Sum(I(OUTx)
Sink Leakage Current
OUTx = V = 40 V, EN = 0 V
−
−
−
−
300
10
mA
S
CSB = V
CC
0 V < V < 5.25 V
CC
OUTx = V = 13.2 V, EN = 0 V
S
CSB = V
CC
0 V < V < 5.25 V, T = 25°C
CC
J
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
4. Thermal characteristics are not subject to production test
5. For temperatures above 85°C, refer to Figure 6.
6. For temperatures above 85°C, refer to Figure 7.
7. Current limit is active with and without overcurrent detection.
www.onsemi.com
5
NCV7703C
ELECTRICAL CHARACTERISTICS
(−40°C ≤ T ≤ 150°C, 5.5 V ≤ V ≤ 40 V, 3.15 V ≤ V ≤ 5.25 V, EN = V , unless otherwise specified)
J
S
CC
CC
Characteristic
Conditions
Min
Typ
Max
Unit
OUTPUTS
Under Load Detection Threshold
Source
Sink
−17
2.0
−7.0
7.0
−2.0
17
mA
V
Power Transistor Body Diode Forward Voltage I = 500 mA
−
0.9
1.3
f
OVERCURRENT
Overcurrent Shutdown Threshold (OUTHx)
Overcurrent Shutdown Threshold (OUTLx)
CURRENT LIMIT (Note 7)
V
V
= 5 V, Vs = 13.2 V
−2.0
1.1
−1.45
1.45
−1.1
2.0
A
A
CC
= 5 V, Vs = 13.2 V
CC
Current Limit (OUTHx)
V
V
= 5 V, Vs = 13.2 V
= 5 V, Vs = 13.2 V,
A
A
CC
−5.0
2.0
−3.0
3.0
−2.0
5.0
Current Limit (OUTLx)
CC
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
4. Thermal characteristics are not subject to production test
5. For temperatures above 85°C, refer to Figure 6.
6. For temperatures above 85°C, refer to Figure 7.
7. Current limit is active with and without overcurrent detection.
www.onsemi.com
6
NCV7703C
ELECTRICAL CHARACTERISTICS
(−40°C ≤ T ≤ 150°C, 5.5 V ≤ V ≤ 40 V, 3.15 V ≤ V ≤ 5.25 V, EN = V , unless otherwise specified)
J
S
CC
CC
Characteristic
Symbol
Conditions
Min
Typ
Max
Unit
LOGIC INPUTS (EN, SI, SCLK, CSB)
Input Threshold
High
Low
V
2.0
−
−
−
−
0.8
Input Hysteresis (EN, SI, SCLK, CSB)
Pulldown Resistance (EN, SI, SCLK)
Pullup Resistance (CSB)
Input Capacitance (Note 8)
LOGIC OUTPUT (SO)
100
50
50
−
400
125
125
10
800
250
250
15
mV
kW
kW
pF
EN = SI = SCLK = V
CSB = 0 V
CC
Output High
I
I
= 1 mA
V
CC
– 1.0
V – 0.7
CC
−
V
V
out
Output Low
= −1.6 mA
−
−10
−
0.2
−
0.4
10
15
out
Tri−state Leakage
CSB = V , 0 V v SO v V
CSB = V
mA
pF
CC
CC
Tri−state Input Capacitance (Note 8)
TIMING SPECIFICATIONS
Under Load Detection Delay Time
Overcurrent Shutdown Delay Time
10
CC
200
350
600
ms
V
= 5 V, Vs = 13.2 V,
CC
Bit13 = 0
Bit13 = 1
80
10
200
25
400
50
ms
ms
High Side Turn On Time
High Side Turn Off Time
Low Side Turn On Time
Low Side Turn Off Time
High Side Rise Time
High Side Fall Time
Low Side Rise Time
Low Side Fall Time
NonOverlap Time
ThsOn
V
V
V
V
V
V
V
V
= 13.2 V, R
= 13.2 V, R
= 13.2 V, R
= 13.2 V, R
= 13.2 V, R
= 13.2 V, R
= 13.2 V, R
= 13.2 V, R
= 25 W
= 25 W
= 25 W
= 25 W
= 25 W
= 25 W
= 25 W
= 25 W
−
−
7.5
3.0
6.5
3.0
5.0
2.0
1.0
1.0
−
15
6.0
15
6.0
10
5.0
3.0
3.0
−
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
S
S
S
S
S
S
S
S
load
load
load
load
load
load
load
load
ThsOff
TlsOn
−
TlsOff
−
ThsTr
−
ThsTf
−
TlsTr
−
TlsTf
−
ThsOffLsOn
TlsOffHsOn
High Side Turn Off to Low Side Turn On
Low Side Turn Off to High Side Turn On
1.0
1.0
NonOverlap Time
−
−
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
8. Not production tested.
www.onsemi.com
7
NCV7703C
ELECTRICAL CHARACTERISTICS
(−40°C < T < 150°C, 5.5 V < V < 3.15 V < V < 5.25 V, EN = V , unless otherwise specified)
J
S
CC
CC
Characteristic
Conditions
Symbol
Min
Typ
Max
Unit
SERIAL PERIPHERAL INTERFACE (V = 5 V)
CC
SCLK Frequency
−
−
−
−
5.0
MHz
ns
SCLK Clock Period
V
CC
V
CC
= 5 V
= 3.3 V
200
500
−
−
−
−
Maximum Input Capacitance (Note 9)
SCLK High Time
SI, SCLK
−
−
−
−
−
12
−
pF
ns
ns
ns
TCLKH
TCLKL
85
85
SCLK Low Time
−
SCLK Setup Time
TCLKSU1
TCLKSU2
85
85
−
−
−
−
SI Setup Time
SI Hold Time
TISU
TIHT
50
50
−
−
−
−
ns
ns
ns
CSB Setup Time
TCSBSU1
TSSBSU2
100
100
−
−
−
−
CSB High Time (Note 10)
TCSBHT
TSOCSBF
TSOCSBR
−
5.0
−
−
−
−
50
50
25
25
100
ms
ns
ns
ns
ns
ns
SO enable after CSB falling edge
SO disable after CSB rising edge
SO Rise Time (10% to 90%)
SO Fall Time (90% to 10%)
SO Valid Time (Note 9)
−
−
C
C
= 40 pF
= 40 pF
−
10
10
50
load
load
−
−
SCLK High to SO 50%
TSOV
−
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
9. Not tested in production
10.This is the minimum time the user must wait between SPI commands.
www.onsemi.com
8
NCV7703C
CHARACTERISTIC TIMING DIAGRAMS
TlsTr
90%
TlsOff
50%
10%
LS Turn OFF
HS Turn ON
TlsOffHsOn
90%
50%
10%
ThsTr
50%
ThsOn
CSB
LS Turn On
TlsTf
90%
50%
TlsOn
10%
HS Turn Off
ThsOffLsOn
90%
50%
10%
ThsTf
50%
ThsOff
CSB
Figure 4. Detailed Driver Timing
www.onsemi.com
9
NCV7703C
TCLKSU2
TCSBHT
50%
CSB
50%
50%
TCSBSU1
TCSBSU2
50%
SCLK
50%
50%
50%
50%
50%
TCLKH
TCLKL
TCLKSU1
CSB
50%
50%
50%
50%
SO
TSOCSBF
50%
TSOCSBR
SI
50%
TIHT
50%
50%
SCLK
SO
TISU
TSOV
50%
Figure 5. SPI Timing Diagram
www.onsemi.com
10
NCV7703C
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
7.0
6.0
5.0
4.0
3.0
2.0
V
S
= 5.25 V
V
S
= 13.2 V
1.0
0
V
= 0 V to 5.25 V
CC
0
−40 −20
0
20 40
60 80 100 120 140 160
−40 −20
0
20 40
60 80 100 120 140 160
T , TEMPERATURE (°C)
J
T , TEMPERATURE (°C)
J
Figure 6. VS Sleep Supply Current vs. Temperature
Figure 7. VCC Sleep Supply Current vs. Temperature
www.onsemi.com
11
NCV7703C
TYPICAL CHARACTERISTICS
140
120
100
80
1 oz Cu
2 oz Cu
60
40
20
0
0
100 200 300 400 500 600 700 800
2
COPPER HEAT SPREADING AREA (mm )
Figure 8. qJA vs. Copper Spreader Area,
14 Lead SON (fused leads)
1000
100
10
2
Cu Area = 100 mm 1.0 oz
2
200 mm 1.0 oz
2
300 mm 1.0 oz
2
400 mm 1.0 oz
2
1
500 mm 1.0 oz
0.1
0.01
0.000001 0.00001
0.0001
0.001
0.01
0.1
1
10
100
1000
TIME (sec)
Figure 9. Transient Thermal Response to a
Single Pulse 1 oz Copper (Log−Log)
140
120
2
Cu Area = 100 mm 1.0 oz
2
200 mm 1.0 oz
100
80
2
300 mm 1.0 oz
2
400 mm 1.0 oz
2
500 mm 1.0 oz
60
40
20
0
0.000001 0.00001
0.0001
0.001
0.01
0.1
1
10
100
1000
TIME (sec)
Figure 10. Transient Thermal Response to a
Single Pulse 1 oz Copper (Semi−Log)
www.onsemi.com
12
NCV7703C
SPI Communication
Frame Detection
Standard 16−bit communication has been implemented to
this IC to turn drivers on/off, and to report faults. (See
Figure 12). The LSB (Least Significant Bit) is clocked in
first.
Input word integrity (SI) is evaluated by the use of a frame
consistency check. The word frame length is compared to an
h x 16 bit acceptable word length before the data is latched
into the input register. This guarantees the proper word
length has been imported and allows for daisy chain
operation applications.
The frame length detector is enabled with the CSB falling
edge and the SCLK rising edge.
SCLK must be low during the CSB rising edge. The fault
register is cleared with a valid frame detection. Existing
faults are re−latched after the fault filter time.
Communication is Implemented as Follows:
1. CSB goes low to allow serial data transfer.
2. A 16 bit word is clocked (SCLK) into the SI
(Serial Input) pin.
3. CSB goes high to transfer the clocked in
information to the data registers.
NOTE: SO is tristate when CSB is high.
Frame detection starts
Frame detection mode ends with
CSB rising edge.
after the CSB falling edge
and the SCLK rising edge.
CSB
SCLK
SI
SRR OUTL1 OUTH1 OUTL2 OUTH2 OUTL3 OUTH3
X
X
X
X
X
X
OCD ULDSD OVLO
Internal Counter
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Valid 16 bits shown
Figure 11. Frame Detection
CSB
SRR OUTL1 OUTH1 OUTL2 OUTH2 OUTL3 OUTH3
X
X
X
X
X
X
X
X
OCD ULDSD OVLO
SI
SCLK
TW
OUTL1 OUTH1 OUTL2 OUTH2 OUTL3 OUTH3
X
X
X
STA OCDR ULDR PSF
SO
Figure 12. SPI Communication Frame Format
Table 1 defines the programming bits and diagnostic bits.
Figure 12 displays the timing diagram associated with
Table 1. Fault information is sequentially clocked out the
SO pin of the NCV7703C as programming information is
clocked into the SI pin of the device. Daisy chain
communication between SPI compatible IC’s is possible by
connection of the Serial Output pin (SO) to the input of the
sequential IC (SI) (Reference the Daisy Chain Section).
www.onsemi.com
13
NCV7703C
Table 1. SPI BIT DESCRIPTION
Input Data
Output Data
Bit Number
Bit Description
Bit Status
Bit Number
Bit Description
Bit Status
0 = No Fault
1 = Fault
15
Over Voltage Lock Out
Control (OVLO)
0 = Disable
1 = Enable
0 = Disable
1 = Enable
0 = 200 msec
1 = 25 msec
15
Power Supply Fail Signal
(PSF for OVLO or UVLO)
14
13
12
Under Load Detection Shut
Down Control (ULDSD)
14
13
12
Under Load Detection Reporting
Signal (ULDR)
0 = No Fault
1 = Fault
Over Current Detection Shut
Down Control (OCD)
Over Current Detection
Reporting Signal (OCDR)
0 = No Fault
1 = Fault
Not Used
Shoot−Through Attempt
(STA)
0 = No Attempt
1 = Attempt
11
10
9
Not Used
Not Used
Not Used
Not Used
Not Used
OUTH3
11
10
9
Not Used
Not Used
Not Used
Not Used
Not Used
OUTH3
8
8
7
7
6
0 = Off
1 = On
6
0 = Off
1 = On
5
4
3
2
1
0
OUTL3
OUTH2
0 = Off
5
4
3
2
1
0
OUTL3
OUTH2
0 = Off
1 = On
1 = On
0 = Off
0 = Off
1 = On
1 = On
OUTL2
0 = Off
OUTL2
0 = Off
1 = On
1 = On
OUTH1
0 = Off
OUTH1
0 = Off
1 = On
1 = On
OUTL1
0 = Off
OUTL1
0 = Off
1 = On
1 = On
Status Register Reset (SRR)
0 = No Reset
1 = Reset
Thermal Warning (TW)
0 = Not in TW
1 = In TW
DETAILED OPERATING DESCRIPTION
Power Up/Down Control
General
The NCV7703C Triple Half Bridge Driver provides drive
capability for 3 Half−Bridge configurations. Each output
drive is characterized for a 500 mA load and has a typical
1.4 A surge capability. Strict adherence to integrated circuit
die temperature is necessary, with a maximum die
temperature of 150°C. This may limit the number of drivers
enabled at one time. Output drive control and fault reporting
are handled via the SPI (Serial Peripheral Interface) port.
An Enable function (EN) provides a low quiescent sleep
current mode when the device is not being utilized. A pull
down is provided on the EN, SI and SCLK inputs to ensure
they default to a low state in the event of a severed input
signal. A pull−up is provided on the CSB input disabling SPI
communication in the event of an open CSB input.
A feature incorporated in the IC is an under voltage
lockout circuit that prevents the output drivers from turning
on unintentionally. V
and V are monitored for
CC
S
undervoltage conditions supporting a smooth turn−on
transition. All drivers are initialized in the off (high
impedance) condition, and will remain off during a V or
CC
V
S
undervoltage condition. This allows power up
sequencing of V , and V up to the user. Once V is out
CC
S
CC
of UVLO, SPI communication can begin regardless of the
voltage on V . The V supply input does not ever affect the
S
S
SPI logic. However, drivers will remain off if V is in an
S
undervoltage condition. Hysteresis in the UVLO circuits
results in glitch free operation during power up/down.
www.onsemi.com
14
NCV7703C
Overvoltage Shutdown (Table 2)
Overvoltage lockout circuitry monitors the voltage on the
to “1”, all outputs will turn off during this overvoltage
condition. Turn On/Off status is maintained in the logic
circuitry, so that when proper input voltage level is
reestablished, the programmed outputs will turn back on.
The PSF output bit is reset with SRR = 1.
V pin. The response to an overvoltage condition is selected
S
by SPI input bit 15. PSF output bit 15 is set when a V
overvoltage condition exists. If input bit 15 (OVLO) is set
S
Table 2. INPUT BIT 15, OVERVOLTAGE LOCK OUT (OVLO) SHUT DOWN
OVLO Input
Bit 15
V
OVLO
Output Data Bit 15 Power
Supply Fail (PSF) Status
S
Condition
OUTx Status
Unchanged
Unchanged
Unchanged
0
0
1
1
0
1
0
1
0
1 (Need SRR to reset)
0
1 (Need SRR to reset)
All Outputs Shut Off (Remain off until V is out of OVLO)
S
H−Bridge Driver Configuration
Detection shutdown protects the device during current limit
because the Overcurrent threshold is below the Current
Limit threshold. The Overcurrent Detection Shutdown
Control Timer is initiated at the Overcurrent Shutdown
Threshold which starts before the Current Limit is reached.
Note: High currents will cause a rise in die temperature.
Devices will not be allowed to turn on if the die temperature
exceeds the thermal shutdown temperature.
The NCV7703C has the flexibility of controlling each half
bridge driver independently. This allows for high side, low
side and H−bridge control. H−bridge control provides
forward, reverse, brake and high impedance states.
Overvoltage Clamping − Driving Inductive Loads
Each output is internally clamped to ground and VS by
internal freewheeling diodes. The diodes have ratings that
complement the FETs they protect. A flyback event from
driving an inductive load causes the voltage on the output to
rise up. Once the voltage rises higher than VS by a diode
voltage (body diode of the high−side driver), the energy in
the inductor will dissipate through the diode to VS. If a
reverse battery diode is used in the system, care must be
taken to insure the power supply capacitor is sufficient to
dampen any increase in voltage to VS caused by the current
flow through the body diode so that it is below 40 V.
Negative transients will momentarily occur when a
high−side driver driving an inductive load is turned off. This
will be clamped by an internal diode from the output pin
(OUT1 or OUT2) to the IC ground.
Shoot−Through Attempt
The NCV7703C provides detection for attempting to turn
on common drivers of the same channel (OUTL1&OUTH1,
OUTL2&OUTH2, OUTL3&OUTH3) simultaneously. An
attempt to turn on common drivers if allowed would result
in a high current event from VS to GND. Any attempt to
create this setup is recorded in bit 12 of the output data and
forces the common high−side and low−side driver to an off
state. The STA output bit is reset with SRR = 1. The STA bit
must be cleared before an affected driver can turn on.
Overcurrent Shutdown
Effected outputs will turn off when the Overcurrent
Shutdown Threshold has been breached for the Overcurrent
Shutdown Delay Time. The respective OCDR status bit will
be set to a “1” and the driver will latch off. The driver can
only be turned back on via the SPI port with a SPI command
that includes an SRR = 1.
Current Limit
OUTx current is limited per the Current Limit electrical
parameter for each driver. The magnitude of the current has
a minimum specification of 2 A at V = 5 V and V =
CC
s
13.2 V. The output is protected for high power conditions
during Current Limit by thermal shutdown and the
Overcurrent Detection shutdown function. Overcurrent
Note: High currents will cause a rise in die temperature.
Devices will not be allowed to turn on if the die temperature
exceeds the thermal shutdown temperature.
Table 3. OVERCURRENT DETECTION SHUT DOWN
OCD Input
Bit 13
OUTx OCD
Condition
Output Data Bit 13 Over
Current Detect (OCDR) Status
Current Limit
of all Drivers
OUTx Status
0
0
0
1
0
Unchanged
3 A
3 A
1 (Need SRR to reset)
OUTx Latches off after 200 ms
(Need SRR to reset)
1
1
0
1
0
Unchanged
3 A
3 A
1 (Need SRR to reset)
OUTx Latches Off After 25 ms
(Need SRR to reset)
www.onsemi.com
15
NCV7703C
Overcurrent Detection Shut Down Control Timer
There are two protection mechanisms for output current,
overcurrent and current limit.
Once an Overcurrent Shutdown Delay Time event has
been detected by the NCV7703C, the timer setting cannot be
interrupted by an attempted change via a SPI command of
Bit 13.
1. Current limit − Always active with a typical
threshold of 3 A (typ).
2. Overcurrent Detection − Selectable shutdown time
via Bit 13 with a 1.45 A (typ) threshold.
Table 4.
Figure 13 shows the typical performance of a part which
has exceeded the 1.45 A (typ) Overcurrent Detection
threshold and started the shutdown control timer. When Bit
13 = 1, the shutdown time is 25 msec (typ). When Bit 13 =
0, the shutdown time is 200 msec (typ).
Input Bit 13
Overcurrent Shutdown Delay Time
200 msec (typ)
0
1
25 msec (typ)
(Current Limit) 3 A
(Current Limit) 1.45 A
OUTx Current
25 msec (typ)
Bit13 = 1
(Current Limit) 3 A
(Current Limit) 1.45 A
OUTx Current
Bit13 = 0
200 msec (typ)
Figure 13. Output Current Shutdown Control
UnderLoad Detection (Table 5)
The NCV7703C uses a global under load timer. An under
load condition starts the global under load delay timer. If
under load occurs in another channel after the global timer
has been started, the delay for any subsequent under load
will be the remainder of the initially started timer. The timer
runs continuously with any persistent under load condition
and will impact multi−underload situations. The under load
detect bit is reset by setting input data bit 0, SRR = 1.
The underload detection circuit monitors the current from
each output driver. A minimum load current (this is the
maximum open circuit detection threshold) is required when
the drivers are turned on. If the under−load detection
threshold has been detected continuously for more than the
under−load delay time, the ULDR bit (output bit #14) will
be set to a “1”. In addition, the offending driver will be
latched off if input Bit 14 (ULDSD) is set to 1 (true).
Table 5. OUTPUT BIT 14, UNDER LOAD DETECTION SHUT DOWN
ULDSD Input
Bit 14
OUTx ULD
Condition
Output Data Bit 14, Under
Load Detect (ULDR) Status
OUTx Status
0
0
1
1
0
1
0
1
0
Unchanged
Unchanged
1 (Need SRR to reset)
0
Unchanged
1 (Need SRR to reset)
OUTx Latches Off (Need SRR to reset)
www.onsemi.com
16
NCV7703C
Thermal Shutdown
Three independent thermal shutdown circuits are featured
(one common sensor for each HS and LS transistor pair).
Each sensor has two temperature levels; Level 1, Thermal
Warning sets the “TW” status bit to a 1 and would have to
be reset with a command that includes the SRR after the IC
cools to a temperature below Level 1. The output will remain
on in this condition.
If the IC temperature reaches Level 2, Over Temperature
Shutdown, all drivers are latched off. It can be reset only
after the part cools below the shutdown temperature,
(including thermal hysteresis) with a turn−on command that
includes the SRR set bit.
software polling of this bit will allow for load control and
possible prevention of thermal shutdown conditions.
Thermal warning information can be retrieved
immediately without performing a complete SPI access
cycle. Figure 14 below displays how this is accomplished.
Bringing the CSB pin from high to low with SI = 0
immediately displays the information on Output Data Bit 0,
thermal warning. As the temperature of the NCV7703C
changes from a condition from below the thermal warning
threshold to above the thermal warning threshold, the state
of the SO pin changes and this level is available immediately
when the CSB goes low. A low on SO indicates there is no
thermal warning, while a high indicates the IC is above the
thermal warning threshold. This warning bit is reset by
setting SRR to “1”.
The output data bit 0, Thermal Warning, will latch and
remain set, even after cooling, and is reset by sending a SPI
command to reset the status register (SRR, input 0 set to
“1”). Since thermal warning precedes a thermal shutdown,
CSB
CSB
SCLK*
SCLK*
Tristate Level
SO
SO
TWH
NTW
Tristate Level
Thermal Warning High
No Thermal Warning
*SCLK can be high or low in order to maintain the thermal information on SO. Toggling SCLK will cause other output bits to shift out.
TWH = Thermal Warning High
NTW = No Thermal Warning
Figure 14. Access to Temperature Warning Information
Applications Drawing
Daisy Chain
The NCV7703C is capable of being setup in a daisy chain
configuration with other similar devices which include
additional NCV7703C devices as well as the NCV7708
Double Hex Driver. Particular attention should be focused
on the fact that the first 16 bits which are clocked out of the
SO pin when the CSB pin transitions from a high to a low
will be the Diagnostic Output Data. These are the bits
representing the status of the IC and are detailed in the SPI
Bit Description Table. Additional programming bits should
be clocked in which follow the Diagnostic Output bits. Word
length must be h x 16 due to the use of frame detection.
www.onsemi.com
17
NCV7703C
CSB SCLK
NCV7703C
CSB SCLK
CSB SCLK
NCV7708C
CSB SCLK
NCV7708C
NCV7703C
SI
SO
SI
SO
SI
SO
SI
SO
Figure 15. Daisy Chain Operation
Parallel Control
A more efficient way to control multiple SPI compatible
devices is to connect them in a parallel fashion and allow
each device to be controlled in a multiplex mode. The
diagram below shows a typical connection between the
microprocessor or microcontroller and multiple SPI
compatible devices. In a daisy chain configuration, the
programming information for the last device in the serial
string must first pass through all the previous devices. The
parallel control setup eliminates that requirement, but at the
cost of additional control pins from the microprocessor for
each individual CSB pin for each controllable device. Serial
data is only recognized by the device that is activated
through its respective CSB pin.
V
S
OUTx
NCV7703C
SI
SCLK
SI
SCLK
CSB
SO
OUT1
OUT2
OUT3
SO
OUTx
CSB
NCV7703C
SI
chip1
CSB
SCLK
CSB
SO
chip2
OUT1
OUT2
OUT3
CSB
chip3
GND
NCV7703C
SI
SCLK
CSB
SO
OUT1
OUT2
OUT3
Figure 17. High−Side / Low−Side Application Drawing
Figure 16. Parallel Control
Any combination of H−bridge and high or low−side
drivers can be designed in. This allows for flexibility in
many systems.
Additional Application Setup
In addition to the cascaded H−Bridge application shown
in Figure 1, the NCV7703C can also be used as a high−side
driver or low−side driver (Figure 17).
www.onsemi.com
18
NCV7703C
PACKAGE DIMENSIONS
SOIC−14 NB
CASE 751A−03
ISSUE K
NOTES:
D
A
B
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE PROTRUSION
SHALL BE 0.13 TOTAL IN EXCESS OF AT
MAXIMUM MATERIAL CONDITION.
4. DIMENSIONS D AND E DO NOT INCLUDE
MOLD PROTRUSIONS.
14
8
7
A3
E
H
5. MAXIMUM MOLD PROTRUSION 0.15 PER
SIDE.
L
DETAIL A
1
MILLIMETERS
DIM MIN MAX
INCHES
MIN MAX
13X b
M
M
B
0.25
A
A1
A3
b
D
E
1.35
0.10
0.19
0.35
8.55
3.80
1.75 0.054 0.068
0.25 0.004 0.010
0.25 0.008 0.010
0.49 0.014 0.019
8.75 0.337 0.344
4.00 0.150 0.157
M
S
S
B
0.25
C A
DETAIL A
h
A
X 45
_
e
H
h
L
1.27 BSC
0.050 BSC
6.20 0.228 0.244
0.50 0.010 0.019
1.25 0.016 0.049
5.80
0.25
0.40
0
M
A1
e
M
7
0
7
_
_
_
_
SEATING
PLANE
C
SOLDERING FOOTPRINT*
6.50
14X
1.18
1
1.27
PITCH
14X
0.58
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
For additional information, please contact your local
Sales Representative
NCV7703C/D
◊
相关型号:
©2020 ICPDF网 联系我们和版权申明