MN101CF94D [PANASONIC]
MN101C94D;
| 型号： | MN101CF94D |
| 厂家： | 
PANASONIC |
| 描述： | MN101C94D 微控制器和处理器 外围集成电路 时钟 |
| 文件： | 总3页 (文件大小：289K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MN101C94A
Type
MN101C94A
Mask ROM
32K
MN101CF94D
FLASH
64K
Internal ROM type
ROM (byte)
RAM (byte)
1K
2K
Package (Lead-free)
QFP044-P-1010F
0.10 µs (at 4.5 V to 5.5 V, 20 MHz)
0.238 µs (at 2.7 V to 5.5 V, 8.39 MHz)
0.477 µs (at 2.0 V to 5.5 V, 4.19 MHz)*
Minimum Instruction
Execution Time
* The lower limit for operation guarantee for flash memory built-in type is 2.5 V.
Interrupts
RESET, Watchdog, External 0 to 2, Timer 0 to 5, Time base, Serial 0, A/D conversion finish
Timer Counter
Timer counter 0 : 8-bit × 1 (square-wave/8-bit PWM output, event count, generation of remote control carrier)
Clock source................ 1/1, 1/4 of system clock frequency; 1/1 of OSC oscillation clock frequency; external clock input
Interrupt source ........... coincidence with compare register 0
Timer counter 1 : 8-bit × 1 (square-wave output, event count, synchronous output event)
Clock source................ 1/16, 1/64 of system clock frequency; external clock input
Interrupt source ........... coincidence with compare register 1
Timer counter 0, 1 can be cascade-connected.
Timer counter 2 : 8-bit × 1 (square-wave/8-bit PWM output, event count, synchronous output event)
Clock source................ 1/1, 1/4 of system clock frequency; external clock input
Interrupt source ........... coincidence with compare register 2
Timer counter 3 : 8-bit × 1
(square-wave output, event count, generation of remote control carrier, serial 0 baud rate timer)
Clock source................ 1/4, 1/16 of system clock frequency; 1/1 of OSC oscillation clock frequency; external clock input
Interrupt source ........... coincidence with compare register 3
Timer counter 2, 3 can be cascade-connected.
Timer counter 4 : 16-bit × 1 (square-wave/16-bit PWM output, event count, synchronous output event, input capture)
Clock source................ 1/4, 1/16 of system clock frequency; 1/1 of OSC oscillation clock frequency; external clock input
Interrupt source ........... coincidence with compare register 4
Time base timer (one-minute count setting, independently operable 8-bit timer counter 5)
Clock source................ 1/4 of system clock frequency; 1/1, 1/8192 of OSC oscillation clock frequency
Interrupt source ........... coincidence with compare register 5; 1/8192 prescaler overflow
Watchdog timer
Interrupt source ........... 1/1048576 of system clock frequency
Serial interface
Serial 0 : synchronous type/simple UART (half-duplex) × 1
Clock source................ 1/2, 1/4, 1/16 of system clock frequency; output of timer counter 3
I/O Pins
Common use : 17, Specified pull-up resistor available
Input/output selectable (bit unit) : 26
I/O
26
11
Input
Common use, Specified pull-up resistor available
A/D converter
10-bit × 8-ch. (with S/H)
Special Ports
Buzzer output, remote control carrier signal output, high-current drive port
MAD00052CEM
MN101C94A
Electrical Charactreistics (Supply current)
Limit
Parameter
Symbol
Condition
Unit
min
typ
15
6
max
40
18
3
IDD1
IDD2
IDD3
IDD4
IDD5
fosc = 20 MHz , VDD = 5 V
mA
mA
mA
µA
Operating supply current
Supply current at HALT
Supply current at STOP
fosc = 8.39 MHz , VDD = 5 V
fosc = 8.39 MHz , VDD = 5 V , Ta = 25°C
VDD = 5 V , Ta = 25°C
1.2
2
VDD = 5 V , Ta = –40°C to +85°C
20 (50) µA
) : Flash memory built-in type
(
Development tools
In-circuit Emulator
PX-ICE101C/D+PX-PRB101C94-QFP044-P-1010
Pin Assignment
P64
P65
22
21
20
19
18
17
16
15
14
13
12
P10, RMOUT
P06, BUZZER
P02, SBT0
P01, SBI0, RXD
P00, SBO0, TXD
N.C.
34
35
36
37
38
39
40
41
42
43
44
P66
P67
P70
MN101C94A
NRST, P27
MMOD
LED7, P87
LED6, P86
LED5, P85
LED4, P84
VSS
OSC1
OSC2
VDD
PA7, AN7
QFP044-P-1010F
MAD00052CEM
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other
company which may arise as a result of the use of technical information described in this book.
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
– Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-
ucts may directly jeopardize life or harm the human body.
– Any applications other than the standard applications intended.
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita
Electric Industrial Co., Ltd. Industrial Co., Ltd.
相关型号：
MN101CFA7D
Microcontroller, 8-Bit, FLASH, 10MHz, CMOS, PQFP48, 7 X 7 MM, LEAD FREE, PLASTIC, QFP-48
PANASONIC
MN101CP28DHT
Microcontroller, 8-Bit, OTPROM, 20MHz, CMOS, PQFP80, 14 X 14 MM, LEAD FREE, PLASTIC, LQFP-80
PANASONIC
MN101CP38C
Microcontroller, 8-Bit, OTPROM, 20MHz, CMOS, PQFP100, 14 X 14 MM, LEAD FREE, PLASTIC, LQFP-100
PANASONIC
©2020 ICPDF网 联系我们和版权申明