UCLAMP0801T.TCT [SEMTECH]
Trans Voltage Suppressor Diode, 8V V(RWM), Unidirectional, 1 Element, Silicon, 1 X 0.60 MM, HALOGEN FREE AND ROHS COMPLIANT, ULTRA SMALL, PLASTIC, 2 PIN;型号: | UCLAMP0801T.TCT |
厂家: | SEMTECH CORPORATION |
描述: | Trans Voltage Suppressor Diode, 8V V(RWM), Unidirectional, 1 Element, Silicon, 1 X 0.60 MM, HALOGEN FREE AND ROHS COMPLIANT, ULTRA SMALL, PLASTIC, 2 PIN 局域网 二极管 |
文件: | 总7页 (文件大小:153K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
uClamp0801T
Low Profile μClamp®
1-Line ESD protection
PROTECTION PRODUCTS - MicroClamp®
Features
Description
The μClamp® series of TVS arrays are designed to pro-
tect sensitive electronics from damage or latch-up due
to ESD. It is designed to replace multilayer varistors
(MLVs) in portable applications such as cell phones, note-
book computers, and other portable electronics. It fea-
tures large cross-sectional area junctions for conducting
high transient currents. They offer desirable character-
istics for board level protection including fast response
time, low operating and clamping voltage, and no device
degradation.
Transient protection for data lines to
IEC 61000-4-2 (ESD) ±15kV (air), ±8kV (contact)
IEC 61000-4-4 (EFT) 40A (tp = 5/50ns)
Cable Discharge Event (CDE)
Ultra-small package (1.0 x 0.6 x 0.4mm)
Protects one data line
Low clamping voltage
Working voltage: 8V
Low leakage current
Solid-state silicon-avalanche technology
The μClamp0801T is in a 2-pin, SLP1006P2T package.
It measures 1.0 x 0.6 mm with a nominal height of only
0.4mm. The leads are spaced at a pitch of 0.65mm
and are finished with lead-free NiPdAu. Each device
will protect one line operating at 8 volts. It gives the
designer the flexibility to protect single lines in applica-
tions where arrays are not practical. They may be used
to meet the ESD immunity requirements of IEC 61000-
4-2, Level 4 (±15kV air, ±8kV contact discharge). The
combination of small size and high ESD surge capability
makes them ideal for use in portable applications such
as cellular phones, digital cameras, and MP3 players.
Mechanical Characteristics
SLP1006P2T package
Pb-Free, Halogen Free, RoHS/WEEE Compliant
Nominal Dimensions: 1.0 x 0.6 x 0.4 mm
Lead Finish: NiPdAu
Molding compound flammability rating: UL 94V-0
Marking : Marking code, cathode band
Packaging : Tape and Reel
Applications
Cellular Handsets & Accessories
Personal Digital Assistants (PDAs)
Notebooks & Handhelds
Portable Instrumentation
Digital Cameras
Peripherals
MP3 Players
Dimensions
Schematic & PIN Configuration
1.0
2
0.60
0.65
0.40
1
Nominal Dimensions (mm)
SLP1006P2T (Bottom View)
www.semtech.com
Revision 03/30/2011
1
uClamp0801T
PROTECTION PRODUCTS
Absolute Maximum Rating
Rating
Symbol
Value
Units
ESD per IEC 61000-4-2 (Air)
ESD per IEC 61000-4-2 (Contact)
VESD
+/- 20
+/- 15
kV
Operating Temperature
Storage Temperature
TJ
-55 to +125
-55 to +150
°C
°C
TSTG
Electrical Characteristics (T=25oC)
Parameter
Reverse Stand-Off Voltage
Reverse Breakdown Voltage
Reverse Leakage Current
Clamping Voltage
Symbol
VRWM
VBR
IR
Conditions
Minimum
Typical
Maximum
Units
8
V
V
It = 1mA
9.5
12.5
0.25
17
VRWM = 8V, T=25°C
IPP = 1.5A, tp = 8/20μs
IF = 10mA
μA
V
VC
Forward Voltage
VF
1
1.2
10
V
Junction Capacitance
Junction Capacitance
Cj
VR = 0V, f = 1MHz
VR = 3.3V, f = 1MHz
pF
pF
Cj
4.5
www.semtech.com
© 2011 Semtech Corp.
2
uClamp0801T
PROTECTION PRODUCTS
Typical Characteristics
Typical Insertion Loss (S21)
Normalized Junction Capacitance vs. Reverse Voltage
CH1 S21 LOG
6 dB / REF 0 dB
1.2
1.1
1
1: -2.3043 dB
800 MHz
1: -2.6270 dB
900 MHz
0 dB
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
1
2
2: -9.3111 dB
1.8 GHz
-6 dB
3
-12 dB
-18 dB
-24 dB
-30 dB
-36 dB
3: -21.903 dB
2.7 GHz
0.1
f = 1 MHz
0
0
1
2
3
4
5
6
7
8
Reverse Voltage - VR (V)
1
10
100
3
1
MHz
MHz
MHz
GHz GHz
3
.
STOP 000000000MHz
.
START 030 MHz
Clamping Voltage vs. Peak Pulse Current
20
18
16
14
12
10
8
6
Waveform
Parameters:
tr = 8μs
4
2
td = 20μs
0
0
0.5
1
1.5
2
Peak Pulse Current - IPP (A)
ESD Clamping
ESD Clamping
(+8kV Contact per IEC 61000-4-2)
(-8kV Contact per IEC 61000-4-2)
Note: ESD data is taken with a 10x attenuator
www.semtech.com
© 2011 Semtech Corp.
3
uClamp0801T
PROTECTION PRODUCTS
Applications Information
Device Connection Options
Circuit Diagram
This device is designed to protect one data or power
supply line. The device is unidirectional and may be
used on lines where the signal polarity is above ground.
The cathode band should be placed towards the line
that is to be protected.
Circuit Board Layout Recommendations for Suppres-
sion of ESD.
Good circuit board layout is critical for the suppression
of ESD induced transients. The following guidelines are
recommended:
z
z
z
z
Place the TVS near the input terminals or connec-
tors to restrict transient coupling.
Minimize the path length between the TVS and the
protected line.
Minimize all conductive loops including power and
ground loops.
The ESD transient return path to ground should be
kept as short as possible.
z
z
Never run critical signals near board edges.
Use ground planes whenever possible.
www.semtech.com
© 2011 Semtech Corp.
4
uClamp0801T
PROTECTION PRODUCTS
Applications Information - Spice Model
uClamp0801T Spice Model
uClamp0801T Spice Parameters
Parameter
Unit
Amp
Volt
Volt
Ohm
Amp
Farad
sec
--
D1 (TVS)
3.87E-13
10.9
IS
BV
VJ
0.79
RS
IBV
CJO
TT
2.71
1.0E-3
5.71E-12
2.541E-9
0.27
M
N
--
1.1
EG
eV
1.11
www.semtech.com
© 2011 Semtech Corp.
5
uClamp0801T
PROTECTION PRODUCTS
Outline Drawing - SLP1006P2T
B
A
D
DIMENSIONS
INCHES MILLIMETERS
MIN NOM MAX MIN NOM MAX
E
DIM
A
A1
b
D
E
e
.015
.000
.018
.017 0.37 0.40 0.43
.016
0.00
.001 .002
0.03 0.05
TOP VIEW
.022 0.45 0.50 0.55
.020
1.00
0.60
.035 .039 .043 0.90
1.10
.020 .024 .028 0.50
0.70
.026 BSC
0.65 BSC
L
.008 .010 .012 0.20 0.25 0.30
.002 .004 .006 0.05 0.10 0.15
A
R
SEATING
PLANE
N
2
.003
.004
2
0.08
0.10
aaa C
A1
aaa
bbb
C
PIN 1 ID
R
bxN
bbb
C A B
2x L
e
BOTTOM VIEW
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
Land Pattern - SLP1006P2T
DIMENSIONS
Y
DIM
INCHES
MILLIMETERS
Z
(.033)
.012
.024
.022
.055
(0.85)
0.30
0.60
0.55
1.40
(C)
C
G
X
Y
Z
G
X
NOTES:
1.
CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY.
CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR
COMPANY'S MANUFACTURING GUIDELINES ARE MET.
2.
www.semtech.com
© 2011 Semtech Corp.
6
uClamp0801T
PROTECTION PRODUCTS
Marking Code
Ordering Information
Working Qty per Reel
Part Number
Voltage
Reel
Size
uClamp0801T.TCT
8V
3,000 7 Inch
Notes:
8T
1) This is a lead-free, RoHS/WEEE compliant product
MicroClamp, uClamp and μClamp are marks of Semtech
Corporation
PIN 1 ID
Tape and Reel Specification
Cathode Bar
User Direction of feed
Device Orientation in Tape
A0
B0
K0
0.69 +/-0.10 mm
1.19 +/-0.10 mm
0.66 +/-0.10 mm
Tape
B, (Max)
Width
D
D1
E
F
P
P0
P2
T
W
1.5 + 0.1 mm
1.750±.10
mm
(.069±.004)
4.0±0.10
mm
(.157±.00-
4)
4.0±0.1
mm
(.157±.00-
4)
8.0 mm
+ 0.3 mm
- 0.1 mm
0.4 mm
±0.25
(.031)
3.5±0.05
mm
(.138±.002)
2.0±0.05
mm
(.079±.002)
4.2 mm
8 mm
- 0.0 mm
(0.59 +.005
- .000)
0.254±0.02
mm (.016)
(.165)
(.312±.012)
Contact Information
Semtech Corporation
Protection Products Division
200 Flynn Rd., Camarillo, CA 93012
Phone: (805)498-2111 FAX (805)498-3804
www.semtech.com
© 2011 Semtech Corp.
7
相关型号:
UCLAMP0871P.TNT
Trans Voltage Suppressor Diode, 1500W, 8V V(RWM), Unidirectional, 1 Element, Silicon,
SEMTECH
UCLAMP1071P.TNT
Trans Voltage Suppressor Diode, 1500W, 10V V(RWM), Unidirectional, 1 Element, Silicon,
SEMTECH
©2020 ICPDF网 联系我们和版权申明