TPS61088-Q1 [TI]
符合 AEC-Q100 标准的 10A 完全集成式同步升压转换器;型号: | TPS61088-Q1 |
厂家: | TEXAS INSTRUMENTS |
描述: | 符合 AEC-Q100 标准的 10A 完全集成式同步升压转换器 升压转换器 |
文件: | 总35页 (文件大小:2012K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
TPS61088-Q1
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
TPS61088-Q1 10A 全集成同步升压转换器
1 特性
3 说明
1
•
符合面向汽车应用的 AEC-Q100 标准:
器件温度等级 1:–40°C 至 +125°C,TA
TPS61088-Q1 是一款输入电压为 2.7V 至 12V 的高功
率密度同步升压转换器,旨在为汽车应用提供高效的小
尺寸 解决方案。TPS61088-Q1 的最低输入电压为
2.7V,因此也可在需要高功率输出的应用(比如紧急
呼叫)中为单节或者双节锂离子备用电池 (BUB) 升
压, 进而 驱动扬声器、天线以及其它电路。
–
•
•
•
•
输入电压范围:2.7V 至 12V
输出电压范围:4.5 至 12.6V
10A 开关电流
在 VIN = 5V、
VOUT = 9V 且 IOUT = 3A 时,效率高于 90%
该器件还可用作后升压转换器,即对主汽车系统 3.3V
电源轨进行升压,从而为需要 5V 电压的 CAN 收发器
和其它电路供电。
•
在轻负载条件下,有 PFM 模式和强制 PWM 模式
可供选择
•
•
•
•
•
•
•
•
关断期间,流入 VIN 引脚的电流为 1µA
可通过电阻编程的开关峰值电流限制
可调节的开关频率范围:200kHz 至 2.2MHz
可编程软启动
12.6V 输出电压能力使得 TPS61088-Q1 同样能够为音
频放大器(例如,为紧急呼叫系统提供 10V 或 11V 电
压)、天线、同轴电缆供电 (PoC) 和汽车音频总线
(A2B) 器件供电。
13.2V 输出过压保护
逐周期过流保护
10A 开关电流可支持 要求 在冷启动期间运行的应用,
例如从 3.5V 输入转化为 11V 输出,同时仍然提供高达
2A 的负载电流。
热关断
20 引脚 4.50mm × 3.50mm 超薄型四方扁平无引线
(VQFN) 封装
器件信息(1)
•
使用 TPS61088-Q1 及其 WEBENCH 电源设计器
创建定制设计
器件型号
封装
VQFN (20)
封装尺寸(标称值)
TPS61088-Q1
4.50mm x 3.50mm
2 应用
(1) 如需了解所有可用封装,请参阅数据表末尾的可订购产品附
录。
•
•
•
汽车紧急呼叫
汽车智能天线
汽车同轴电缆供电 应用
典型应用电路
C6
L1
VIN
VOUT
BOOT
SW
VOUT
FB
C4
R1
FSW
VIN
R2
R3
C2
C1
R5
R4
C5
VCC
EN
COMP
ILIM
C3
ON
OFF
C7
SS
PGND
AGND
MODE
1
本文档旨在为方便起见,提供有关 TI 产品中文版本的信息,以确认产品的概要。 有关适用的官方英文版本的最新信息,请访问 www.ti.com,其内容始终优先。 TI 不保证翻译的准确
性和有效性。 在实际设计之前,请务必参考最新版本的英文版本。
English Data Sheet: SLVSE52
TPS61088-Q1
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
www.ti.com.cn
目录
8.4 Device Functional Modes........................................ 13
Application and Implementation ........................ 15
9.1 Application Information............................................ 15
9.2 Typical Application .................................................. 15
1
2
3
4
5
6
7
特性.......................................................................... 1
应用.......................................................................... 1
说明.......................................................................... 1
修订历史记录 ........................................................... 2
(说明 (续))....................................................... 3
Pin Configuration and Functions......................... 4
Specifications......................................................... 5
7.1 Absolute Maximum Ratings ...................................... 5
7.2 ESD Ratings.............................................................. 5
7.3 Recommended Operating Conditions....................... 5
7.4 Thermal Information.................................................. 5
7.5 Electrical Characteristics........................................... 6
7.6 Typical Characteristics.............................................. 7
Detailed Description ............................................ 10
8.1 Overview ................................................................. 10
8.2 Functional Block Diagram ....................................... 11
8.3 Feature Description................................................. 11
9
10 Power Supply Recommendations ..................... 23
11 Layout................................................................... 23
11.1 Layout Guidelines ................................................. 23
11.2 Layout Example .................................................... 23
11.3 Thermal Considerations........................................ 24
12 器件和文档支持 ..................................................... 25
12.1 器件支持................................................................ 25
12.2 接收文档更新通知 ................................................. 25
12.3 社区资源................................................................ 25
12.4 商标....................................................................... 25
12.5 静电放电警告......................................................... 25
12.6 术语表 ................................................................... 25
13 机械、封装和可订购信息....................................... 25
8
4 修订历史记录
注:之前版本的页码可能与当前版本有所不同。
Changes from Original (September 2018) to Revision A
Page
•
首次发布生产数据数据表 ........................................................................................................................................................ 1
2
版权 © 2018, Texas Instruments Incorporated
TPS61088-Q1
www.ti.com.cn
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
5 (说明 (续))
TPS61088-Q1 使用自适应恒定关断时间峰值电流控制拓扑来调节输出电压。在中等到重负载条件下,TPS61088-
Q1 在脉宽调制 (PWM) 模式下工作。在轻负载条件下,该器件可通过 MODE 引脚选择下列两种工作模式之一。一
种是可提高效率的 PFM 模式;另一种是可避免因开关频率较低而引发应用问题的强制 PWM 模式。可通过外部电
阻在 200kHz 至 2.2MHz 范围内调节 PWM 模式下的开关频率。TPS61088-Q1 还实现了可编程的软启动功能和可
调节的开关峰值电流限制功能。此外,该器件还提供 13.2V 输出过压保护、逐周期过流保护和热关断保护。
TPS61088-Q1 可提供小型 4.50mm × 3.50mm、20 引脚 VQFN 封装。
版权 © 2018, Texas Instruments Incorporated
3
TPS61088-Q1
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
www.ti.com.cn
6 Pin Configuration and Functions
RHL Package
20 Pin VQFN With Thermal Pad
Top View
EN
FSW
SW
ILIM
COMP
FB
SW
VOUT
VOUT
VOUT
MODE
NC
RHL
SW
SW
PGND
BOOT
VIN
Pin Functions
PIN
NUMBER
I/O
DESCRIPTION
NAME
VCC
Output of the internal regulator. A ceramic capacitor of more than 1 µF is required between this pin and
ground.
1
O
Enable logic input. Logic high level enables the device. Logic low level disables the device and turns it
into shutdown mode.
EN
2
3
I
I
I
FSW
SW
The switching frequency is programmed by a resister between this pin and the SW pin.
The switching node pin of the converter. It is connected to the drain of the internal low-side power
MOSFET and the source of the internal high-side power MOSFET.
4, 5, 6, 7
Power supply for high-side MOSFET gate driver. A ceramic capacitor of 0.1 µF must be connected
between this pin and the SW pin
BOOT
VIN
8
9
O
I
IC power supply input
Soft-start programming pin. An external capacitor sets the ramp rate of the internal error amplifier's
reference voltage during soft-start
SS
10
O
No connection inside the device. Connect these two pins to ground plane on the PCB for good thermal
dissipation
NC
11, 12
13
—
I
Operation mode selection pin for the device in light load condition. When this pin is connected to
ground, the device works in PWM mode. When this pin is left floating, the device works in PFM mode.
MODE
VOUT
FB
14, 15, 16
17
O
I
Boost converter output
Voltage feedback. Connect to the center tape of a resistor divider to program the output voltage.
Output of the internal error amplifier, the loop compensation network should be connected between this
pin and the AGND pin.
COMP
ILIM
18
19
O
O
Adjustable switch peak current limit. An external resister should be connected between this pin and the
AGND pin.
AGND
PGND
20
21
—
—
Signal ground of the IC
Power ground of the IC. It is connected to the source of the low-side MOSFET.
4
Copyright © 2018, Texas Instruments Incorporated
TPS61088-Q1
www.ti.com.cn
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature (unless otherwise noted)
(1)
MIN
–0.3
–0.3
–0.3
–0.3
–40
MAX
SW + 7
14.5
7
UNIT
BOOT
VIN, SW, FSW, VOUT
Voltage(2)
V
EN, VCC, SS, COMP, MODE
ILIM, FB
3.6
TJ
Operating junction temperature
Storage temperature
150
°C
°C
Tstg
–65
150
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to network ground terminal.
7.2 ESD Ratings
VALUE
±2000
±750
UNIT
Human body model (HBM), Classification Level 2 per AEC Q100-002, all pins(1)
Charged device model (CDM), Classification Level C5 per AEC Q100-011, all pins
Electrostatic
discharge
V(ESD)
V
(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
2.7
NOM
MAX
12
UNIT
VIN
VOUT
L
Input voltage range
V
V
Output voltage range
4.5
12.6
10
Inductance, effective value
Input capacitance, effective value
Output capacitance, effective value
Operating junction temperature
0.47
10
2.2
47
µH
µF
µF
°C
CI
CO
TJ
6.8
1000
125
–40
7.4 Thermal Information
TPS61088-Q1
THERMAL METRIC(1)
RHL (VQFN) - 20 PINS
UNIT
STANDARD
EVM
25.8
N/A
N/A
0.3
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
36.4
31.4
14.2
0.5
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
ψJB
14.2
2.6
8.8
RθJC(bot)
N/A
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
Copyright © 2018, Texas Instruments Incorporated
5
TPS61088-Q1
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
www.ti.com.cn
7.5 Electrical Characteristics
Minimum and maximum values are at VIN = 2.7 V to 12 V and TJ = -40°C to 125°C. Typical values are at VIN = 3.6 V and TJ =
25°C
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
POWER SUPPLY
VIN
Input voltage range
2.7
12
2.7
2.5
V
V
VIN rising
VIN falling
Undervoltage lockout (UVLO)
threshold
VIN_UVLO
2.4
200
2.1
V
VIN_HYS
VIN UVLO hysteresis
UVLO threshold
mV
V
VCC_UVLO
VCC falling
Operating quiescent current from the
VIN pin
1
3
µA
µA
IC enabled, VEN = 2 V, no load, RILIM = 100
kΩ , VFB = 1.3 V, VOUT = 12 V, TJ up to 125°C
IQ
Operating quiescent current from the
VOUT pin
110
250
IC disabled, VEN = 0 V, no load, no feedback
resistor divider connected to the VOUT pin, TJ
up to 125°C
ISD
Shutdown current into the VIN pin
1
3.5
µA
V
VCC
VCC regulation
IVCC = 5 mA, VIN = 8 V
5.8
EN AND MODE INPUT
VENH
EN high threshold voltage
VCC = 6 V
VCC = 6 V
VCC = 6 V
VCC = 6 V
VCC = 6 V
VCC = 6 V
1.2
4.0
V
V
VENL
EN low threshold voltage
0.4
1.5
REN
EN internal pull-down resistance
MODE high threshold voltage
MODE low threshold voltage
MODE internal pull-up resistance
800
800
kΩ
V
VMODEH
VMODEL
RMODE
OUTPUT
VOUT
V
kΩ
Output voltage range
4.5
12.6
V
V
PWM mode
PFM mode
VFB = 1.2 V
1.186
1.204
1.212
1.222
VREF
Reference voltage at the FB pin
ILKG_FB
ISS
FB pin leakage current
100
nA
Soft-start charging current
5
μA
ERROR AMPLIFIER
ISINK
COMP pin sink current
COMP pin source current
VFB = VREF +200 mV, VCOMP = 1.5 V
VFB = VREF –200 mV, VCOMP = 1.5 V
20
20
µA
µA
ISOURCE
VCCLPH
High clamp voltage at the COMP pin VFB = 1 V, RILIM = 49.9 kΩ
2.3
V
VFB = 1.5 V, RILIM = 49.9 kΩ, MODE pin
floating
VCCLPL
Low clamp voltage at the COMP pin
Error amplifier transconductance
1.4
GEA
POWER SWITCH
High-side MOSFET on-resistance
Low-side MOSFET on-resistance
CURRENT LIMIT
Peak switch current limit in PFM
VCOMP = 1.5 V
190
µA/V
VCC = 6 V
VCC = 6 V
19.5
18.0
29.7
27.5
mΩ
mΩ
RDS(on)
RILIM = 49.9 kΩ, VCC = 6 V, MODE pin floating
10.0
7.2
11.4
13.0
10.5
A
mode
ILIM
Peak switch current limit in FPWM
mode
RILIM = 49.9 kΩ, VCC = 6 V, MODE pin short to
ground
8.7
0.6
A
V
VILIM
Reference voltage at the ILIM pin
SWITCHING FREQUENCY
RFREQ =301 kΩ, VIN = 5.0 V, VOUT = 9.0 V
RFREQ =53.6 kΩ, VIN = 5.0 V, VOUT = 9.0 V
RFREQ =301 kΩ, VIN = 5.0 V, VOUT = 9.0 V
500
2000
90
kHz
kHz
ns
ƒSW
Switching frequency
Minimum on-time
tON_min
160
6
Copyright © 2018, Texas Instruments Incorporated
TPS61088-Q1
www.ti.com.cn
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
Electrical Characteristics (continued)
Minimum and maximum values are at VIN = 2.7 V to 12 V and TJ = -40°C to 125°C. Typical values are at VIN = 3.6 V and TJ =
25°C
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
PROTECTION
Output overvoltage protection
threshold
VOVP
VOUT rising
12.7
13.2
0.25
13.6
V
V
Output overvoltage protection
hysteresis
VOVP_HYS
VOUT falling below VOVP
THERMAL SHUTDOWN
TSD
Thermal shutdown threshold
Thermal shutdown hysteresis
TJ rising
150
20
°C
°C
TSD_HYS
TJ falling below TSD
7.6 Typical Characteristics
100
90
80
70
60
50
40
30
20
10
0
100
80
60
40
20
VIN = 3.0V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2 V
VIN = 3.0V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2 V
0
0.0001
0.001
0.01
0.05
0.2 0.5
1
2 3 45
0.0001
0.001
0.01
0.05
0.2 0.5
1
2 3 45
Output Current (A)
D001
Output Current (A)
D002
VOUT = 5 V, PFM
图 1. Efficiency vs Output Current
VOUT = 5 V, FPWM
图 2. Efficiency vs Output Current
100
90
80
70
60
50
40
30
20
10
0
100
80
60
40
20
0
VIN = 3.0V
VIN = 3.0V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2 V
VIN = 5.0 V
VIN = 8.4 V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2 V
VIN = 5.0 V
VIN = 8.4 V
0.0001
0.001
0.01
0.05
0.2 0.5
1
2 3 45
0.0001
0.001
0.01
0.05
0.2 0.5
1
2 3 45
Output Current (A)
Output Current (A)
D003
D004
VOUT = 9 V, PFM
图 3. Efficiency vs Output Current
VOUT = 9 V, FPWM
图 4. Efficiency vs Output Current
版权 © 2018, Texas Instruments Incorporated
7
TPS61088-Q1
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
www.ti.com.cn
Typical Characteristics (接下页)
100
90
80
70
60
50
40
100
80
60
40
20
0
VIN = 3.0V
VIN = 3.0V
30
20
10
VIN = 3.3V
VIN = 3.6V
VIN = 4.2 V
VIN = 5.0 V
VIN = 8.4 V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2 V
VIN = 5.0 V
VIN = 8.4 V
0
0.0001
0.001
0.01
0.05
0.2 0.5
1
2 3 45
0.0001
0.001
0.01
0.05
0.2 0.5
1
2 3 45
Output Current (A)
Output Current (A)
D005
D006
VOUT = 12 V, PFM
图 5. Efficiency vs Output Current
VOUT = 12 V, FPWM
图 6. Efficiency vs Output Current
14
12
10
8
2200
2000
1800
1600
1400
1200
1000
800
PFM Mode
FPWM Mode
6
4
600
400
2
200
0
0
40
50
60
70
80
90
100
110
0
100 200 300 400 500 600 700 800 900 1000
Resistance (kW)
Resistance(kW)
TPS6
D008
图 7. Current Limit vs Setting Resistance
图 8. Switching Frequency vs Setting Resistance
150
145
140
135
130
125
120
115
110
105
100
95
3.5
3
2.5
2
1.5
1
0.5
0
-40
-20
0
20
40
60
80
100 120 140
-40
-20
0
20
40
60
80
100 120 140
Temperature(èC)
Temperature (èC)
D010
D009
图 9. Quiescent Current vs Temperature
图 10. Shutdown Current vs Temperature
8
版权 © 2018, Texas Instruments Incorporated
TPS61088-Q1
www.ti.com.cn
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
Typical Characteristics (接下页)
1.21
1.209
1.208
1.207
1.206
1.205
1.204
1.203
1.202
1.201
1.2
-40
-20
0
20
40
60
80
100
1201
Temperature (°C)
D007
图 11. Reference Voltage vs Temperature
版权 © 2018, Texas Instruments Incorporated
9
TPS61088-Q1
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
www.ti.com.cn
8 Detailed Description
8.1 Overview
The TPS61088-Q1 is a fully-integrated synchronous boost converter with a 21.3-mΩ power switch and a 24.4-
mΩ rectifier switch to output high power from a single cell or two-cell Lithium batteries. The device is capable of
providing an output voltage of 12.6 V and delivering up to 30-W power from a 5-V input.
The TPS61088-Q1 uses adaptive constant off-time peak current control topology to regulate the output voltage.
In moderate to heavy load condition, the TPS61088-Q1 works in the quasi-constant frequency pulse width
modulation (PWM) mode. The switching frequency in the PWM mode is adjustable ranging from 200 kHz to 2.2
MHz by an external resistor. In light load condition, the device has two operation modes selected by the MODE
pin. When the MODE pin is left floating, the TPS61088-Q1 works in the pulse frequency modulation (PFM) mode.
The PFM mode brings high efficiency at the light load. When the MODE pin is short to ground, the TPS61088-Q1
works in the forced PWM mode (FPWM). The FPWM mode can avoid the acoustic noise and other problems
caused by the low switching frequency. The TPS61088-Q1 implements cycle-by-cycle current limit to protect the
device from overload conditions during boost switching. The switch peak current limit is programmable by an
external resistor. The TPS61088-Q1 uses external loop compensation, which provides flexibility to use different
inductors and output capacitors. The adaptive off-time peak current control scheme gives excellent transient line
and load response with minimal output capacitance.
10
版权 © 2018, Texas Instruments Incorporated
TPS61088-Q1
www.ti.com.cn
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
8.2 Functional Block Diagram
L1
VIN
C3
C1
SW
VIN
BOOT
VOUT
VOUT
C2
Deadtime
Control Logic
C4
LDO
VCC
R3
PGND
Comp
Comp
C5
CLMIT
FB
FSW
gm
R4
R1
SS
1/K
VIN
Comp
SW
COMP
EN
C7
Vref
R2
C6
SS Vref
Vref
Shutdown
Shutdown
Control
AGND
ILIM
ON/
OFF
CLMIT
OVP
VOUT
VIN
UVLO
Mode
Selection
R5
Thermal
Shutdown
MODE
8.3 Feature Description
8.3.1 Enable and Start-up
The TPS61088-Q1 has an adjustable soft-start function to prevent high inrush current during start-up. To
minimize the inrush current during start-up, an external capacitor, connected to the SS pin and charged with a
constant current, is used to slowly ramp up the internal positive input of the error amplifier. When the EN pin is
pulled high, the soft-start capacitor CSS (C7 in the Functional Block Diagram) is charged with a constant current
of 5 μA typically. During this time, the SS pin voltage is compared with the internal reference (1.204 V), the lower
one is fed into the internal positive input of the error amplifier. The output of the error amplifier (which determines
the inductor peak current value) ramps up slowly as the SS pin voltage goes up. The soft-start phase is
completed after the SS pin voltage exceeds the internal reference (1.204 V). The larger the capacitance at the
SS pin, the slower the ramp of the output voltage and the longer the soft-start time. A 47-nF capacitor is usually
sufficient for most applications. When the EN pin is pulled low, the voltage of the soft-start capacitor is
discharged to ground.
Use 公式 1 to calculate the soft-start time.
版权 © 2018, Texas Instruments Incorporated
11
TPS61088-Q1
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
www.ti.com.cn
Feature Description (接下页)
VREF ìCSS
tSS
=
ISS
where
•
•
•
•
tSS is the soft-start time.
VREF is the internal reference voltage of 1.204 V.
CSS is the capacitance between the SS pin and ground.
ISS is the soft-start charging current of 5 µA.
(1)
8.3.2 Undervoltage Lockout (UVLO)
The UVLO circuit prevents the device from malfunctioning at low input voltage and the battery from excessive
discharge. The TPS61088-Q1 has both VIN UVLO function and VCC UVLO function. It disables the device from
switching when the falling voltage at the VIN pin trips the UVLO threshold VIN_UVLO, which is typically 2.4 V. The
device starts operating when the rising voltage at the VIN pin is 200-mV above the VIN_UVLO. It also disables the
device when the falling voltage at the VCC pin trips the UVLO threshold VCC_UVLO, which is typically 2.1 V.
8.3.3 Adjustable Switching Frequency
This device features a wide adjustable switching frequency ranging from 200 kHz to 2.2 MHz. The switching
frequency is set by a resistor connected between the FSW pin and the SW pin of the TPS61088-Q1. A resistor
must always be connected from the FSW pin to SW pin for proper operation. The resistor value required for a
desired frequency can be calculated using 公式 2.
VOUT
1
4ì(
- tDELAY
ì
)
ƒSW
V
IN
RFREQ
=
CFREQ
where
•
•
•
•
•
•
RFREQ is the resistance connected between the FSW pin and the SW pin.
CFREQ = 23 pF
ƒSW is the desired switching frequency.
tDELAY = 89 ns
VIN is the input voltage.
VOUT is the output voltage.
(2)
8.3.4 Adjustable Peak Current Limit
To avoid an accidental large peak current, an internal cycle-by-cycle current limit is adopted. The low-side switch
is turned off immediately as soon as the switch current touches the limit. The peak switch current limit can be set
by a resistor at the ILIM pin to ground. The relationship between the current limit and the resistance depends on
the status of the MODE pin.
When the MODE pin is floating, namely the TPS61088-Q1 is set to work in the PFM mode at light load, use 公式
3 to calculate the resistor value:
where
•
•
RILIM is the resistance between the ILIM pin and ground.
ILIM is the switch peak current limit.
(3)
When the resistor value is 49.9 kΩ, the typical current limit is 11 A.
When the MODE pin is connected to ground, namely the TPS61088-Q1 is set to work in the forced PWM mode
at light load, use 公式 4 to calculate the resistor value.
12
版权 © 2018, Texas Instruments Incorporated
TPS61088-Q1
www.ti.com.cn
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
Feature Description (接下页)
(4)
When the resistor value is 49.9 kΩ, the typical current limit is 9.4 A.
Considering the device variation and the tolerance over temperature, the minimum current limit at the worst case
can be 1.5 A lower than the value calculated by above equations.
8.3.5 Overvoltage Protection
If the output voltage at the VOUT pin is detected above 13.2 V (typical value), the TPS61088-Q1 stops switching
immediately until the voltage at the VOUT pin drops the hysteresis value lower than the output overvoltage
protection threshold. This function prevents overvoltage on the output and secures the circuits connected to the
output from excessive overvoltage.
8.3.6 Thermal Shutdown
A thermal shutdown is implemented to prevent damages due to excessive heat and power dissipation. Typically,
the thermal shutdown happens at a junction temperature of 150°C. When the thermal shutdown is triggered, the
device stops switching until the junction temperature falls below typically 130°C, then the device starts switching
again.
8.4 Device Functional Modes
8.4.1 Operation
The synchronous boost converter TPS61088-Q1 operates at a quasi-constant frequency pulse width modulation
(PWM) in moderate to heavy load condition. Based on the VIN to VOUT ratio, a circuit predicts the required off-
time of the switching cycle. At the beginning of each switching cycle, the low-side N-MOSFET switch, shown in
Functional Block Diagram, is turned on, and the inductor current ramps up to a peak current that is determined
by the output of the internal error amplifier. After the peak current is reached, the current comparator trips, and it
turns off the low-side N-MOSFET switch and the inductor current goes through the body diode of the high-side
N-MOSFET in a dead-time duration. After the dead-time duration, the high-side N-MOSFET switch is turned on.
Because the output voltage is higher than the input voltage, the inductor current decreases. The high-side switch
is not turned off until the fixed off-time is reached. After a short dead-time duration, the low-side switch turns on
again and the switching cycle is repeated.
In light load condition, the TPS61088-Q1 implements two operation modes, PFM mode and forced PWM mode,
to meet different application requirements. The operation mode is set by the status of the MODE pin. When the
MODE pin is connected to ground, the device works in the forced PWM mode. When the MODE pin is left
floating, the device works in the PFM mode.
8.4.1.1 PWM Mode
In the forced PWM mode, the TPS61088-Q1 keeps the switching frequency unchanged in light load condition.
When the load current decreases, the output of the internal error amplifier decreases as well to keep the inductor
peak current down, delivering less power from input to output. When the output current further reduces, the
current through the inductor will decrease to zero during the off-time. The high-side N-MOSFET is not turned off
even if the current through the MOSFET is zero. Thus, the inductor current changes its direction after it runs to
zero. The power flow is from output side to input side. The efficiency will be low in this mode. But with the fixed
switching frequency, there is no audible noise and other problems which might be caused by low switching
frequency in light load condition.
版权 © 2018, Texas Instruments Incorporated
13
TPS61088-Q1
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
www.ti.com.cn
Device Functional Modes (接下页)
8.4.1.2 PFM Mode
The TPS61088-Q1 improves the efficiency at light load with the PFM mode. When the converter operates in light
load condition, the output of the internal error amplifier decreases to make the inductor peak current down,
delivering less power to the load. When the output current further reduces, the current through the inductor will
decrease to zero during the off-time. Once the current through the high side N-MOSFET is zero, the high-side
MOSFET is turned off until the beginning of the next switching cycle. When the output of the error amplifier
continuously goes down and reaches a threshold with respect to the peak current of ILIM / 12, the output of the
error amplifier is clamped at this value and does not decrease any more. If the load current is smaller than what
the TPS61088-Q1 delivers, the output voltage increases above the nominal setting output voltage. The
TPS61088-Q1 extends its off time of the switching period to deliver less energy to the output and regulate the
output voltage to 0.7% higher than the nominal setting voltage. With the PFM operation mode, the TPS61088-Q1
keeps the efficiency above 80% even when the load current decreases to 1 mA. In addition, the output voltage
ripple is much smaller at light load due to low peak current. Refer to 图 12.
Output Voltage
PFM mode at light load
1.007 × VOUT_NOM
VOUT_NOM
PWM mode at heavy load
图 12. PFM Mode Diagram
14
版权 © 2018, Texas Instruments Incorporated
TPS61088-Q1
www.ti.com.cn
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
9 Application and Implementation
注
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The TPS61088-Q1 is designed for outputting voltage up to 12.6 V with 11-A switch current capability to deliver
more than 20-W power. The TPS61088-Q1 operates at a quasi-constant frequency pulse-width modulation
(PWM) in moderate to heavy load condition. In light load condition, the converter can either operate in the PFM
mode or in the forced PWM mode according to the mode selection. The PFM mode brings high efficiency over
entire load range, but the PWM mode can avoid the acoustic noise as the switching frequency is fixed. The
converter uses the adaptive constant off-time peak current control scheme, which provides excellent transient
line and load response with minimal output capacitance. The TPS61088-Q1 can work with different inductor and
output capacitor combination by external loop compensation. It also supports adjustable switching frequency
ranging from 200 kHz to 2.2 MHz.
9.2 Typical Application
C6
0.1 µF
VOUT=9 V
IOUT= 2 A
1.2 µH
L1
VIN=3.3V to 4.2V
VOUT
FB
BOOT
C9
1 µF
C4
47 µF
SW
R1
360kQ
R3
R2
FSW
VIN
255kQ
C1
56kQ
C8
10 µF
R5
R4
C2
C5
VCC
COMP
ILIM
C3
0.1 µF
49.9kQ
3.3 µF
EN
PGND
C7
SS
47nF
AGND
MODE
图 13. TPS61088-Q1 3.3 V to 9-V/3-A Output Converter
9.2.1 Design Requirements
表 1. Design Parameters
DESIGN PARAMETERS
Input voltage
EXAMPLE VALUES
3.3 to 4.2 V
Output voltage
9 V
100 mV peak to peak
2 A
Output voltage ripple
Output current rating
Operating frequency
Operation mode at light load
600 kHz
PFM
版权 © 2018, Texas Instruments Incorporated
15
TPS61088-Q1
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
www.ti.com.cn
9.2.2 Detailed Design Procedure
9.2.2.1 Custom Design with WEBENCH Tools
Click here to create a custom design using the TPS61088-Q1 device with the WEBENCH® Power Designer.
1. Start by entering your VIN, VOUT and IOUT requirements.
2. Optimize your design for key parameters like efficiency, footprint and cost using the optimizer dial and
compare this design with other possible solutions from Texas Instruments.
3. WEBENCH Power Designer provides you with a customized schematic along with a list of materials with real
time pricing and component availability.
4. In most cases, you will also be able to:
–
–
–
–
Run electrical simulations to see important waveforms and circuit performance,
Run thermal simulations to understand the thermal performance of your board,
Export your customized schematic and layout into popular CAD formats,
Print PDF reports for the design, and share your design with colleagues.
5. Get more information about WEBENCH tools at www.ti.com/webench.
9.2.2.2 Setting Switching Frequency
The switching frequency is set by a resistor connected between the FSW pin and the SW pin of the TPS61088-
Q1. The resistor value required for a desired frequency can be calculated using 公式 5.
VOUT
1
4ì(
- tDELAY
ì
)
ƒSW
V
IN
RFREQ
=
CFREQ
where
•
•
•
•
•
•
RFREQ is the resistance connected between the FSW pin and the SW pin.
CFREQ = 23 pF
ƒSW is the desired switching frequency.
tDELAY = 89 ns
VIN is the input voltage.
VOUT is the output voltage.
(5)
9.2.2.3 Setting Peak Current Limit
The peak input current is set by selecting the correct external resistor value correlating to the required current
limit. Because the TPS61088-Q1 is configured to work in the PFM mode in light load condition, use 公式 6 to
calculate the correct resistor value:
where
•
•
RILIM is the resistance connected between the ILIM pin and ground.
ILIM is the switching peak current limit.
(6)
For a typical current limit of 11.0 A, the resistor value is 49.9 kΩ. Considering the device variation and the
tolerance over temperature, the minimum current limit at the worst case can be 1.3 A lower than the value
calculated by 公式 6. The minimum current limit must be higher than the required peak switch current at the
lowest input voltage and the highest output power to make sure the TPS61088-Q1 does not hit the current limit
and still can regulate the output voltage in these conditions.
9.2.2.4 Setting Output Voltage
The output voltage is set by an external resistor divider (R1, R2 in the Functional Block Diagram). Typically, a
minimum current of 20 μA flowing through the feedback divider gives good accuracy and noise covering. A
standard 56-kΩ resistor is typically selected for low-side resister R2.
16
版权 © 2018, Texas Instruments Incorporated
TPS61088-Q1
www.ti.com.cn
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
The value of R1 is then calculated as:
(VOUT - VREF )ìR2
R1 =
VREF
(7)
9.2.2.5 Inductor Selection
Because the selection of the inductor affects the power supply’s steady state operation, transient behavior, loop
stability, and boost converter efficiency, the inductor is the most important component in switching power
regulator design. Three most important specifications to the performance of the inductor are the inductor value,
DC resistance, and saturation current.
The TPS61088-Q1 is designed to work with inductor values between 0.47 and 10 µH. A 0.47-µH inductor is
typically available in a smaller or lower-profile package, while a 10-µH inductor produces lower inductor current
ripple. If the boost output current is limited by the peak current protection of the IC, using a 10-µH inductor can
maximize the controller’s output current capability.
Inductor values can have ±20% or even ±30% tolerance with no current bias. When the inductor current
approaches saturation level, its inductance can decrease 20% to 35% from the value at 0-A current depending
on how the inductor vendor defines saturation. When selecting an inductor, make sure its rated current,
especially the saturation current, is larger than its peak current during the operation.
Follow 公式 8 to 公式 10 to calculate the peak current of the inductor. To calculate the current in the worst case,
use the minimum input voltage, maximum output voltage, and maximum load current of the application. To leave
enough design margin, TI recommends using the minimum switching frequency, the inductor value with –30%
tolerance, and a low-power conversion efficiency for the calculation.
In a boost regulator, calculate the inductor DC current as in 公式 8.
VOUT ìIOUT
IDC
=
V ì h
IN
where
•
•
•
•
VOUT is the output voltage of the boost regulator.
IOUT is the output current of the boost regulator.
VIN is the input voltage of the boost regulator.
η is the power conversion efficiency.
(8)
Calculate the inductor current peak-to-peak ripple as in 公式 9.
1
IPP
=
1
1
L ì(
+
)ì ƒSW
VOUT - V
V
IN
IN
where
•
•
•
•
•
IPP is the inductor peak-to-peak ripple.
L is the inductor value.
ƒSW is the switching frequency.
VOUT is the output voltage.
VIN is the input voltage.
(9)
Therefore, the peak current, ILpeak, detected by the inductor is calculated with 公式 10.
IPP
ILpeak = IDC
+
(10)
Set the current limit of the TPS61088-Q1 higher than the peak current ILpeak. Then select the inductor with
saturation current higher than the setting current limit.
Boost converter efficiency is dependent on the resistance of its current path, the switching loss associated with
the switching MOSFETs, and the inductor core loss. The TPS61088-Q1 has optimized the internal switch
resistance. However, the overall efficiency is affected significantly by the DC resistance (DCR) of the inductor,
equivalent series resistance (ESR) at the switching frequency, and the core loss. Core loss is related to the core
material and different inductors have different core loss. For a certain inductor, larger current ripple generates
版权 © 2018, Texas Instruments Incorporated
17
TPS61088-Q1
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
www.ti.com.cn
higher DCR and ESR conduction losses and higher core loss. Usually, a data sheet of an inductor does not
provide the ESR and core loss information. If needed, consult the inductor vendor for detailed information.
Generally, TI recommends an inductor with lower DCR and ESR. However, there is a tradeoff among the
inductor’s inductance, DCR and ESR resistance, and its footprint. Furthermore, shielded inductors typically have
higher DCR than unshielded inductors. 表 2 lists recommended inductors for the TPS61088-Q1. Verify whether
the recommended inductor can support the user's target application with the previous calculations and bench
evaluation. In this application, the Sumida's inductor CDMC8D28NP-1R2MC is selected for its small size and low
DCR.
表 2. Recommended Inductors
PART NUMBER
L (µH)
DCR MAXIMUM
SATURATION CURRENT /
HEAT RATING CURRENT (A)
SIZE MAXIMUM
(L × W × H mm)
Vendor(1)
(mΩ)
CDMC8D28NP-1R2MC
744311150
1.2
1.5
2.2
2.2
2.2
7
7.2
7
12.2 / 12.9
14 / 11
9.5 × 8.7 × 3
7.3 × 7.2 × 4
11.2 × 10.3 × 4
11.2 × 10.3 × 3
7.4 × 6.8 × 5
Sumida
Wurth
PIMB104T-2R2MS
PIMB103T-2R2MS
PIMB065T-2R2MS
18 / 12
Cyntec
Cyntec
Cyntec
9
16 / 13
12.5
12 / 10.5
(1) See Third-party Products Disclaimer
9.2.2.6 Input Capacitor Selection
For good input voltage filtering, TI recommends low-ESR ceramic capacitors. The VIN pin is the power supply for
the TPS61088-Q1. A 0.1-μF ceramic bypass capacitor is recommended as close as possible to the VIN pin of the
TPS61088-Q1. The VCC pin is the output of the internal LDO. A ceramic capacitor of more than 1 μF is required
at the VCC pin to get a stable operation of the LDO.
For the power stage, because of the inductor current ripple, the input voltage changes if there is parasite
inductance and resistance between the power supply and the inductor. It is recommended to have enough input
capacitance to make the input voltage ripple less than 100mV. Generally, 10-μF input capacitance is sufficient for
most applications.
注
DC bias effect: High-capacitance ceramic capacitors have a DC bias effect, which has a
strong influence on the final effective capacitance. Therefore, the right capacitor value
must be chosen carefully. The differences between the rated capacitor value and the
effective capacitance result from package size and voltage rating in combination with
material. A 10-V rated 0805 capacitor with 10 μF can have an effective capacitance of less
5 μF at an output voltage of 5 V.
9.2.2.7 Output Capacitor Selection
For small output voltage ripple, TI recommends a low-ESR output capacitor like a ceramic capacitor. Typically,
three 22-μF ceramic output capacitors work for most applications. Higher capacitor values can be used to
improve the load transient response. Take care when evaluating a capacitor’s derating under DC bias. The bias
can significantly reduce capacitance. Ceramic capacitors can lose most of their capacitance at rated voltage.
Therefore, leave margin on the voltage rating to ensure adequate effective capacitance. From the required output
voltage ripple, use the following equations to calculate the minimum required effective caapctance COUT
:
18
版权 © 2018, Texas Instruments Incorporated
TPS61088-Q1
www.ti.com.cn
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
(VOUT - VIN_MIN)ìIOUT
VOUT ì ƒSW ìCOUT
= ILpeak ìRC _ESR
V
=
ripple _ dis
(11)
V
ripple _ESR
where
•
•
•
•
•
•
•
•
Vripple_dis is output voltage ripple caused by charging and discharging of the output capacitor.
Vripple_ESR is output voltage ripple caused by ESR of the output capacitor.
VIN_MIN is the minimum input voltage of boost converter.
VOUT is the output voltage.
IOUT is the output current.
ILpeak is the peak current of the inductor.
ƒSW is the converter switching frequency.
RC_ESR is the ESR of the output capacitors.
(12)
9.2.2.8 Loop Stability
The TPS61088-Q1 requires external compensation, which allows the loop response to be optimized for each
application. The COMP pin is the output of the internal error amplifier. An external compensation network
comprised of resister R5, ceramic capacitors C5 and C8 is connected to the COMP pin.
The power stage small signal loop response of constant off time (COT) with peak current control can be modeled
by 公式 13.
≈
∆
«
’≈
÷∆
’
÷
S
S
1 +
1 -
RO ì 1 - D
2 ì p ì ƒESRZ ◊«
2 ì p ì ƒRHPZ ◊
(
)
ì
GPS (S) =
S
2 ì Rsense
1 +
2 ì p ì ƒP
where
•
•
•
D is the switching duty cycle.
RO is the output load resistance.
Rsense is the equivalent internal current sense resistor, which is 0.08 Ω.
(13)
(14)
2
ƒP
=
2p ì RO ì CO
where
•
CO is output capacitor.
1
ƒESRZ
=
2p ì RESR ì CO
where
•
RESR is the equivalent series resistance of the output capacitor.
(15)
(16)
2
RO ì 1 - D
(
)
ƒRHPZ
=
2p ì L
版权 © 2018, Texas Instruments Incorporated
19
TPS61088-Q1
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
www.ti.com.cn
The COMP pin is the output of the internal transconductance amplifier. 公式 17 shows the small signal transfer
function of compensation network.
≈
∆
«
’
÷
S
1 +
2 ì p ì ƒCOMZ ◊
GEA ì REA ì VREF
Gc(S) =
ì
VOUT
≈
∆
«
’≈
’
÷
S
S
1 +
1 +
÷∆
2 ì p ì ƒCOMP1 ◊«
2 ì p ì ƒCOMP2 ◊
where
•
•
•
•
•
•
GEA is the amplifier’s transconductance
REA is the amplifier’s output resistance
VREF is the refernce voltage at the FB pin
VOUT is the output voltage
ƒCOMP1, ƒCOMP2 are the poles' frequency of the compensation network.
ƒCOMZ is the zero's frequency of the compensation network.
(17)
The next step is to choose the loop crossover frequency, ƒC. The higher in frequency that the loop gain stays
above zero before crossing over, the faster the loop response is. It is generally accepted that the loop gain cross
over no higher than the lower of either 1/10 of the switching frequency, ƒSW, or 1/5 of the RHPZ frequency,
ƒRHPZ
.
Then set the value of R5, C5, and C8 (in 图 13) by following these equations.
2pì VOUT ìRsense ì ƒC ìCO
R5 =
(1 œ D)ì VREF ìGEA
where
•
ƒC is the selected crossover frequency.
(18)
(19)
(20)
The value of C5 can be set by 公式 19.
RO ìCO
C5 =
2R5
The value of C8 can be set by 公式 20.
RESR ì CO
C8 =
R5
If the calculated value of C8 is less than 10 pF, it can be left open.
Designing the loop for greater than 45° of phase margin and greater than 10-dB gain margin eliminates output
votlage ringing during the line and load transient.
20
版权 © 2018, Texas Instruments Incorporated
TPS61088-Q1
www.ti.com.cn
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
9.2.3 Application Curves
Vout(AC)
20 mV/div
Vout(AC)
100 mV/Div
Inductor
Current
2 A/Div
SW
5 V/div
Inductor
Current
1 A/div
SW
5 V/Div
2 µS/Div
1 uS/div
图 14. Switching Waveforms in CCM
图 15. Switching Waveforms in DCM
Vout(AC)
20 mV/div
EN
1 V/Div
SW
5 V/div
Vout
2 V/Div
Inductor
Current
1 A/div
Inductor
Current
2 A/Div
20 µS/div
2 mS/Div
图 17. Start-up Waveforms
图 16. Switching Waveforms in PFM Mode
EN
1 V/Div
Output
Current
1 A/div
Vout
2 V/Div
Inductor
Current
2 A/Div
Vout(AC)
500 mV/div
500 µS/div
200 µS/Div
VOUT = 9 V
IOUT = 1 to 2 A
图 18. Shutdown Waveforms
图 19. Load Transient
版权 © 2018, Texas Instruments Incorporated
21
TPS61088-Q1
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
www.ti.com.cn
Input
Voltage
500 mV/div
Vout(AC)
100 mV/div
500 µS/div
VOUT = 9 V
VIN = 3.3 to 3.6 V
图 20. Line Transient
22
版权 © 2018, Texas Instruments Incorporated
TPS61088-Q1
www.ti.com.cn
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
10 Power Supply Recommendations
The device is designed to operate from an input voltage supply range between 2.7 V to 12 V. This input supply
must be well regulated. If the input supply is located more than a few inches from the converter, additional bulk
capacitance may be required in addition to the ceramic bypass capacitors. A typical choice is an electrolytic or
tantalum capacitor with a value of 47 μF.
11 Layout
11.1 Layout Guidelines
As for all switching power supplies, especially those running at high switching frequency and high currents,
layout is an important design step. If layout is not carefully done, the regulator could suffer from instability and
noise problems. To maximize efficiency, switch rise and fall times are very fast. To prevent radiation of high-
frequency noise (for example, EMI), proper layout of the high-frequency switching path is essential. Minimize the
length and area of all traces connected to the SW pin, and always use a ground plane under the switching
regulator to minimize interplane coupling.
The input capacitor must be close to the VIN pin and GND pin in order to reduce the Iinput supply ripple.
The layout should also be done with well consideration of the thermal as this is a high power density device. A
thermal pad that improves the thermal capabilities of the package should be soldered to the large ground plate,
using thermal vias underneath the thermal pad.
11.2 Layout Example
The bottom layer is a large ground plane connected to the PGND plane and AGND plane on top layer by vias.
AGND
L1
EN
FSW
SW
ILIM
VIN
COMP
FB
SW
VOUT
VOUT
VOUT
MODE
NC
SW
SW
VOUT
BOOT
VIN
PGND
CIN
COUT
PGND
图 21. Recommended TPS61088-Q1 Layout
版权 © 2018, Texas Instruments Incorporated
23
TPS61088-Q1
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
www.ti.com.cn
11.3 Thermal Considerations
The maximum IC junction temperature should be restricted to 125°C under normal operating conditions.
Calculate the maximum allowable dissipation, PD(max), and keep the actual power dissipation less than or equal to
PD(max). The maximum-power-dissipation limit is determined using 公式 21.
125 - TA
RqJA
PD(max)
=
where
•
•
TA is the maximum ambient temperature for the application.
θJA is the junction-to-ambient thermal resistance given in the Thermal Information table.
R
(21)
The TPS61088-Q1 comes in a thermally-enhanced VQFN package. This package includes a thermal pad that
improves the thermal capabilities of the package. The real junction-to-ambient thermal resistance of the package
greatly depends on the PCB type, layout, and thermal pad connection. Using thick PCB copper and soldering the
thermal pad to a large ground plate enhance the thermal performance. Using more vias connects the ground
plate on the top layer and bottom layer around the IC without solder mask also improves the thermal capability.
24
版权 © 2018, Texas Instruments Incorporated
TPS61088-Q1
www.ti.com.cn
ZHCSIC0A –SEPTEMBER 2018–REVISED NOVEMBER 2018
12 器件和文档支持
12.1 器件支持
12.1.1 第三方产品免责声明
TI 发布的与第三方产品或服务有关的信息,不能构成与此类产品或服务或保修的适用性有关的认可,不能构成此类
产品或服务单独或与任何 TI 产品或服务一起的表示或认可。
12.1.2 开发支持
12.1.2.1 使用 WEBENCH 工具创建定制设计
请单击此处,使用 TPS61088-Q1 器件及其 WEBENCH®电源设计器创建定制设计。
1. 首先,输入您的输入电压、输出电压和输出电流要求。
2. 使用优化器拨盘优化效率、封装和成本等关键设计参数并将您的设计与德州仪器 (TI) 的其它可行解决方案进行
比较。
3. WEBENCH 电源设计器提供一份定制原理图以及罗列实时价格和组件供货情况的物料清单。
4. 在大多数情况下,您还可以:
–
–
–
–
运行电气仿真,观察重要波形以及电路性能;
运行热性能仿真,了解电路板热性能;
将定制原理图和布局方案导出至常用 CAD 格式,
打印设计方案的 PDF 报告并与同事共享。
5. 请访问 www.ti.com.cn/webench,获取有关 WEBENCH 工具的详细信息。
12.2 接收文档更新通知
要接收文档更新通知,请导航至 TI.com.cn 上的器件产品文件夹。单击右上角的通知我进行注册,即可每周接收产
品信息更改摘要。有关更改的详细信息,请查看任何已修订文档中包含的修订历史记录。
12.3 社区资源
下列链接提供到 TI 社区资源的连接。链接的内容由各个分销商“按照原样”提供。这些内容并不构成 TI 技术规范,
并且不一定反映 TI 的观点;请参阅 TI 的 《使用条款》。
TI E2E™ 在线社区 TI 的工程师对工程师 (E2E) 社区。此社区的创建目的在于促进工程师之间的协作。在
e2e.ti.com 中,您可以咨询问题、分享知识、拓展思路并与同行工程师一道帮助解决问题。
设计支持
TI 参考设计支持 可帮助您快速查找有帮助的 E2E 论坛、设计支持工具以及技术支持的联系信息。
12.4 商标
E2E is a trademark of Texas Instruments.
WEBENCH is a registered trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.5 静电放电警告
这些装置包含有限的内置 ESD 保护。 存储或装卸时,应将导线一起截短或将装置放置于导电泡棉中,以防止 MOS 门极遭受静电损
伤。
12.6 术语表
SLYZ022 — TI 术语表。
这份术语表列出并解释术语、缩写和定义。
13 机械、封装和可订购信息
以下页面包含机械、封装和可订购信息。这些信息是指定器件的最新可用数据。数据如有变更,恕不另行通知,且
不会对此文档进行修订。如需获取此数据表的浏览器版本,请查阅左侧的导航栏。
版权 © 2018, Texas Instruments Incorporated
25
重要声明和免责声明
TI 均以“原样”提供技术性及可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资
源,不保证其中不含任何瑕疵,且不做任何明示或暗示的担保,包括但不限于对适销性、适合某特定用途或不侵犯任何第三方知识产权的暗示
担保。
所述资源可供专业开发人员应用TI 产品进行设计使用。您将对以下行为独自承担全部责任:(1) 针对您的应用选择合适的TI 产品;(2) 设计、
验证并测试您的应用;(3) 确保您的应用满足相应标准以及任何其他安全、安保或其他要求。所述资源如有变更,恕不另行通知。TI 对您使用
所述资源的授权仅限于开发资源所涉及TI 产品的相关应用。除此之外不得复制或展示所述资源,也不提供其它TI或任何第三方的知识产权授权
许可。如因使用所述资源而产生任何索赔、赔偿、成本、损失及债务等,TI对此概不负责,并且您须赔偿由此对TI 及其代表造成的损害。
TI 所提供产品均受TI 的销售条款 (http://www.ti.com.cn/zh-cn/legal/termsofsale.html) 以及ti.com.cn上或随附TI产品提供的其他可适用条款的约
束。TI提供所述资源并不扩展或以其他方式更改TI 针对TI 产品所发布的可适用的担保范围或担保免责声明。IMPORTANT NOTICE
邮寄地址:上海市浦东新区世纪大道 1568 号中建大厦 32 楼,邮政编码:200122
Copyright © 2018 德州仪器半导体技术(上海)有限公司
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TPS61088QRHLRQ1
TPS61088QRHLTQ1
ACTIVE
ACTIVE
VQFN
VQFN
RHL
RHL
20
20
3000 RoHS & Green
250 RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
-40 to 125
-40 to 125
S61088Q
S61088Q
NIPDAU
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
7-Jan-2021
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS61088QRHLRQ1
TPS61088QRHLTQ1
VQFN
VQFN
RHL
RHL
20
20
3000
250
330.0
180.0
12.4
12.4
3.8
3.8
4.8
4.8
1.3
1.3
8.0
8.0
12.0
12.0
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
7-Jan-2021
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS61088QRHLRQ1
TPS61088QRHLTQ1
VQFN
VQFN
RHL
RHL
20
20
3000
250
367.0
213.0
367.0
191.0
38.0
35.0
Pack Materials-Page 2
PACKAGE OUTLINE
VQFN - 1 mm max height
RHL0020A
PLASTIC QUAD FLATPACK- NO LEAD
A
3.6
3.4
B
PIN 1 INDEX AREA
4.6
4.4
C
1 MAX
SEATING PLANE
0.08 C
2.05±0.1
2X 1.5
SYMM
0.5
0.3
20X
(0.2) TYP
10
11
14X 0.5
9
12
SYMM
21
2X
3.05±0.1
3.5
19
2
0.29
20X
0.19
0.1
0.05
20
1
PIN 1 ID
(OPTIONAL)
C A B
C
4X (0.2)
2X (0.55)
4219071 / A 05/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
VQFN - 1 mm max height
RHL0020A
PLASTIC QUAD FLATPACK- NO LEAD
(3.3)
(2.05)
2X (1.5)
SYMM
1
20
2X (0.4)
20X (0.6)
19
2
20X (0.24)
14X (0.5)
SYMM
21
(3.05) (4.3)
6X (0.525)
2X (0.75)
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
9
12
(R0.05) TYP
(Ø0.2) VIA
TYP)
10
11
4X (0.2)
4X
(0.775)
2X (0.55)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 18X
0.07 MAX
ALL AROUND
SOLDER MASK
OPENING
0.07 MIN
ALL AROUND
EXPOSED METAL
EXPOSED METAL
METAL
METAL UNDER
SOLDER MASK
SOLDER MASK
OPENING
NON SOLDER MASK
SOLDER MASK
DEFINED
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4219071 / A 05/2017
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments
literature number SLUA271 (www.ti.com/lit/slua271)
.
5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
6. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to theri
locations shown on this view. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
VQFN - 1 mm max height
RHL0020A
PLASTIC QUAD FLATPACK- NO LEAD
(3.3)
2X (1.5)
(0.55)
TYP
(0.56)
TYP
1
20
SOLDER MASK EDGE
TYP
20X (0.6)
2
19
20X (0.24)
14X (0.5)
SYMM
(1.05)
TYP
(4.3)
21
6X
(0.85)
(R0.05) TYP
METAL
TYP
12
9
2X
(0.775)
2X (0.25)
6X (0.92)
11
10
4X (0.2)
SYMM
SOLDER PASTE EXAMPLE
BASED ON 0.1mm THICK STENCIL
EXPOSED PAD
75% PRINTED COVERAGE BY AREA
SCALE: 20X
4219071 / A 05/2017
NOTES: (continued)
7.
Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations..
www.ti.com
重要声明和免责声明
TI 提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,不保证没
有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他安全、安保或其他要求。这些资源如有变更,恕不另行通知。TI 授权您仅可
将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。您无权使用任何其他 TI 知识产权或任何第三方知
识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款 (https:www.ti.com.cn/zh-cn/legal/termsofsale.html) 或 ti.com.cn 上其他适用条款/TI 产品随附的其他适用条款
的约束。TI 提供这些资源并不会扩展或以其他方式更改 TI 针对 TI 产品发布的适用的担保或担保免责声明。IMPORTANT NOTICE
邮寄地址:上海市浦东新区世纪大道 1568 号中建大厦 32 楼,邮政编码:200122
Copyright © 2021 德州仪器半导体技术(上海)有限公司
相关型号:
TPS61088QRHLRQ1
符合 AEC-Q100 标准的 10A 完全集成式同步升压转换器 | RHL | 20 | -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS61088QRHLTQ1
符合 AEC-Q100 标准的 10A 完全集成式同步升压转换器 | RHL | 20 | -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS61088RHLR
10A 全集成同步升压转换器 | RHL | 20 | -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS61088RHLT
10A 全集成同步升压转换器 | RHL | 20 | -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS61089
采用 2.0mm x 2.5mm VQFN 封装的 12.6V、7A 全集成同步升压转换器Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS61089RNRR
采用 2.0mm x 2.5mm VQFN 封装的 12.6V、7A 全集成同步升压转换器 | RNR | 11 | -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS61089RNRT
采用 2.0mm x 2.5mm VQFN 封装的 12.6V、7A 全集成同步升压转换器 | RNR | 11 | -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS61090
SYNCHRONOUS BOOST CONVERTER WITH 2A SWITCHWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS61090EVM-029
EVALUATION MODULEWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS61090RSA
SYNCHRONOUS BOOST CONVERTER WITH 2A SWITCHWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS61090RSAR
SYNCHRONOUS BOOST CONVERTER WITH 2A SWITCHWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS61090RSARG4
SYNCHRONOUS BOOST CONVERTER WITH 2A SWITCHWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
©2020 ICPDF网 联系我们和版权申明