MA4AGSW2 [TE]
AlGaAs SP2T PIN Diode Switch; SP2T的AlGaAs PIN二极管开关
| 型号： | MA4AGSW2 |
| 厂家： | 
TE CONNECTIVITY |
| 描述： | AlGaAs SP2T PIN Diode Switch |
| 文件： | 总6页 (文件大小：233K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
AlGaAs SP2T PIN
Diode Switch
V 1.00
Features
MA4AGSW2 Layout
n
n
n
n
Ultra Broad Bandwidth: 50 MHz to 50 GHz
Functional bandwidth : 50 MHz to 70 GHz
0.7 dB Insertion Loss, 33 dB Isolation at 50 GHz
Low Current consumption:
-10 mA for Low Loss State
+10 mA for Isolation
n
M/A-COM’s unique patent pending AlGaAs
hetero-junction anode technology
Silicon Nitride Passivation
n
n
Polymide Scratch protection
Description
M/A-COM’s MA4AGSW2 is an Aluminum-Gallium-Arsenide
anode enhanced, SP2T PIN diode switch. AlGaAs anodes, which
utilize M/A-COM’s patent pending hetero-junction technology,
which produce less loss than conventional GaAs processes, as
much as 0.3 dB reduction in insertion loss at 50 GHz. These
devices are fabricated on a OMCVD epitaxial wafer using a
process designed for high device uniformity and extremely low
parasitics. The diodes themselves exhibit low series resistance,
low capacitance, and fast switching speed. They are fully
passivated with silicon nitride and have an additional layer of a
polymer for scratch protection. The protective coating prevents
damage to the junction and the anode airbridges during handling.
Off-chip bias circuitry is required and allows maximum design
flexibility.
Absolute Maximum Ratings1
@ TA = +25 °C (Unless otherwise
specified)
Parameter
Operating Temperature
Storage Temperature
Incident C.W. RF Power
Breakdown Voltage
Bias Current
Maximum Rating
-55 °C to +125 °C
-65 °C to +150 °C
+ 23 dBm C. W.
25 V
Applications
The low capacitance of the PIN diodes used makes it ideal for use
in microwave multi-throw switch designs, where the series
capacitance in each off-arm will load the input. Also, the low
series resistance of the diodes helps the total insertion loss of the
devices at microwave frequencies. These AlGaAs PIN switches
are used as the switching arrays for radar systems, radiometers, and
other multi-assembly components.
+/- 30 mA
1. Exceeding any of these values may result in permanent
damage
Nominal Chip Dimensions
Chip Dimensions (mm)
X
Y
Chip
RF
1290
825
Pad Dimensions (mm)
X
Y
100
100
Pad Locations (mm)
X
Y
J1
J2
J3
0
0
-520
+350
+350
+520
Pad Locations Relative to J1
AlGaAs SP2T PIN Diode Switch
Electrical Specifications @ TA = 25 °C, +/- 10 mA Bias Current
MA4AGSW2
V 1.00
(On-Wafer Measurements)
RF Specifications
Parameters
Frequency
Minimum
Typical
Maximum
Units
Insertion Loss
0.05 - 18 GHz
18 - 50 GHz
-
0.5
0.7
0.6
0.9
dB
0.05 - 18 GHz
18 - 50 GHz
45
28
47
33
-
dB
Isolation
0.05 - 18 GHz
18 - 50 GHz
0.05 - 18 GHz
18 - 50 GHz
-
22
21
25
22
-
-
dB
dB
Input Return Loss
Output Return Loss
-
Switching Speed (10% - 90% RF Voltage)
10 GHz
-
20
-
ns
NOTES:
1. Typical switching speed is measured from 10% to 90% of the detected RF voltage driven by a TTL compatible driver. Driver
output parallel RC network uses a capacitor between 390 pF - 560 pF and a resistor between 150 - 220 Ohms to achieve
20 ns rise and fall times.
Typical Driver Connections
Control Level (DC Current)
RF Output Conditions
J2
J3
J2-J1
J3-J1
+10 mA
Low Loss
Isolation
-10 mA
-10 mA
Isolation
+10 mA
Low Loss
2
n North America: Tel. (800) 366-2266
n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298
n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
M/A-COM Inc. and its affiliates reserve the right to make changes to the product(s)
or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
AlGaAs SP2T PIN Diode Switch
Microwave and Millimeter Wave Performance
MA4AGSW2
V 1.00
TYPICAL INSERTION LOSS @ -10 mA
0
-0.2
-0.4
-0.6
-0.8
-1
0.00
10.00
20.00
30.00
40.00
50.00
FREQUENCY ( GHz )
J2
J3
TYPICAL ISOLATION @ +10 mA
0
-10
-20
-30
-40
-50
-60
-70
-80
0.00
10.00
20.00
30.00
40.00
50.00
FREQUENCY ( GHz )
J2
J3
3
n North America: Tel. (800) 366-2266
n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298
n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
M/A-COM Inc. and its affiliates reserve the right to make changes to the product(s)
or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
AlGaAs SP2T PIN Diode Switch
Microwave and Millimeter Wave Performance (cont’d)
MA4AGSW2
V 1.00
TYPICAL INPUT RETURN LOSS @ -10 mA
0
-5
-10
-15
-20
-25
-30
0.00
10.00
20.00
30.00
40.00
50.00
FREQUENCY ( GHz )
J2
J3
TYPICAL OUTPUT RETURN LOSS @ -10 mA
0
-5
-10
-15
-20
-25
-30
0.00
10.00
20.00
30.00
40.00
50.00
FREQUENCY ( GHz )
J2
J3
4
n North America: Tel. (800) 366-2266
n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298
n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
M/A-COM Inc. and its affiliates reserve the right to make changes to the product(s)
or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
AlGaAs SP2T PIN Diode Switch
Assembly Considerations
MA4AGSW2
V 1.00
Solder Die Attachment
The following precautions should be observed to avoid
damaging these chips.
All die attach and bonding methods should be compatible with
gold metal. Solder which does not scavange gold, such as
80Au/20Sn or Sn62/Pb36/Ag2 is recommended. Do not
expose die to a temperature greater than 300 °C for more than
10 seconds.
Cleanliness
These chips should be handled in a clean environment. Do not
attempt to clean die after installation.
Electrically Conductive Epoxy
Die Attachment
Assembly can be preheated to approximately 125 °C. Use a
controlled thickness of approximately 2 mils for best electrical
and thermal conductivity. Cure epoxy as per manufacturer’s
schedule. For extended cure times, temperatures should be
kept below 150 °C.
Electro-Static Sensitivity
These Devices are considered ESD Class1. Proper ESD
techniques should be used when handling these devices.
General Handling
Ribbon/Wire Bonding
The protective polymer coating on the active areas of these die
provides scratch and impact protection, particularly for the
metal airbridge which contacts the diode’s anode. Die should
primarily be handled with vacuum pickups, or alternatively
with plastic tweezers.
Wedge thermocompression bonding or ball bonding may be
used to attach ribbons or wires to the RF bonding pads. Gold
ribbons should be 1/4 x 3 mil sq. for all RF ports for lowest
inductance and best microwave performance.
Mounting Techniques
These AlGaAs devices are designed to be mounted with
electrically conductive silver epoxy or with
a lower
temperature solder perform, which is not rich in Sn content.
Operation of the MA4AGSW2
The Simultaneous Application of Negative DC Current to the Low Loss Port and Positive DC current to the
Remaining Isolated Ports achieves operation of the MA4AGSW Series of AlGaAs PIN Switches. The Backside Area of
the Die is the RF and DC Return Ground Plane. The DC Return is achieved on Common Port J1. Constant Current
Sources should supply the DC Control Currents. The Diode voltages at these Bias Nodes will not exceed + 1.6 volts
( + 1.4 volts typical for Supply Currents up to + 30 mA). In the Low Loss State, the Series Diode must be Forward
Biased and the Shunt Diode Reverse Biased. For All the Isolated Ports, the Shunt Diode is Forward Biased and the
Series Diode is Reverse Biased. The Bias Network Design should yield > 30 dB RF to DC Isolation.
Best Insertion Loss, P1dB, IP3, and Switching Speed is Achieved by using a Voltage Pull-up Resistor in the DC Return
Path, (J1). A Minimum Value of | -2 V | is recommended at this Return Node, which is achievable with a Standard,
+ 5 V TTL Controlled PIN Diode Driver.
5
n North America: Tel. (800) 366-2266
n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298
n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
M/A-COM Inc. and its affiliates reserve the right to make changes to the product(s)
or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
AlGaAs SP2T PIN Diode Switch
MA4AGSW2 Schematic with 2-18 GHz Bias Network
MA4AGSW2
V 1.00
J1
39 pF
22 pF
22 nH
100 Ohms
DC Bias
DC Bias
39 pF
39 pF
22 nH
22 nH
J3
J2
22 pF
22 pF
AlGaAs Switch Die
6
n North America: Tel. (800) 366-2266
n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298
n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
M/A-COM Inc. and its affiliates reserve the right to make changes to the product(s)
or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
相关型号：
©2020 ICPDF网 联系我们和版权申明